DPC3X ATEX version Pre-compensated Load Sensing Sectional Valves
Additional information This catalogue shows the product in the most standard configurations. Please contact Sales Dpt. for more detailed information or special request. WARNING! All specifications of this catalogue refer to the standard product at this date. Walvoil, oriented to a continuous improvement, reserves the right to discontinue, modify or revise the specifications, without notice. WALVOIL IS NOT RESPONSIBLE FOR ANY DAMAGE CAUSED BY AN INCORRECT USE OF THE PRODUCT. st edition March 6
ATEX version General information The DPC Series The DPC Series is a family of open/closed center pre-pressure compensated sectional valves designed specifically for Mobile Applications. The DPC series provides exceptional controllability, efficiency and flexibility for applications requiring up to 4 l/min (63.4 US gpm) flow rate. DPC Series is available in two different sizes: DPC3 (DPC3X) and DPC. DPC3 DPC3X DPC The Load Sensing technology Thanks to the use of specially designed pumps and control valves, the Load Sensing principle can be considered the most comprehensive means of creating a flexible hydraulic circuit that can adapt to the various operating conditions demanded by users. The main feature of this principle is that the flow rate to the user is proportional to the spool position under any operating condition, regardless of the resistance encountered by the user (pressure) and the number of levers activated (exceeding the pump s total flow rate, a condition here in after defined as saturation, is the only limitation). Therefore, with the LS systems, there is a specific correspondence between the position of the control lever and the movement speed of the user, cylinder or hydraulic motor. This feature is particularly useful in the hydraulic handling machine sector (excavators, cranes, loaders, agricultural and forestry machinery) in which each movement phase has specific sequences that the operator must control by using memorised movements. Advantages and options Energy saving. Extension of part service life. Lower energy dissipation. Noise reduction. Available to create a single-pump circuit (compared with the use of multiple-pump circuits in which each pump is dedicated to different actuators to be operated simultaneously). Real energy savings can be obtained above all when the DPC directional valves operate together with variable displacement Load Sensing pumps. When the DPC valve is utilised with fixed displacement pumps, the previously mentioned movement independence and repeatability features are guaranteed, but energy savings will be limited. For special options please contact Sales Dept. The ATEX version The DPC3X is the DPC Series new valve built according to the ATEX directive for safe use in classified areas, with inflammable and potentially explosive materials. Hydraulic features and performance remain the same of the DPC3 standard valve. 3
DPC3X ATEX version Contents Working conditions......................... page 5 Standard threads.............................. 5 ATEX directive introductions....................... 6 Explosion risk assessment........................ 8 Dimensional data and performance................. Complete section ordering codes.................. Inlet section Solenoid operated L.S. unloading valve........... Working section "A" side spool control kit..................... 3 "B" side spool control kit..................... 6 Installation............................... 7 4
ATEX version DPC3X Working conditions This catalogue shows technical specifications and diagrams measured with mineral oil of 46 mm /s - 46 cst viscosity at 4 C - 4 F temperature. Nominal flow rating (open center circuit) Max. pressure Back pressure (max.) Standard internal leakage A(B)->T Fluid Fluid temperature range on inlet port with compensator @ stand-by (margin pressure) 5 l/min - 39.6 US gpm @ 9 bar - 3 psi on working ports with compensator @ stand-by (margin pressure) l/min - 6.4 US gpm @ 7 bar - psi on working ports without compensator @ stand-by (margin pressure) 3 l/min - 34.3 US gpm @ 9 bar - 3 psi P inlet port 35 bar ( ) - 45 psi ( ) A and B working ports 35 bar ( ) - 45 psi ( ) on T outlet port 5 bar - 363 psi on L drain port.5 bar - 36 psi p= bar - 45 psi 6 cm 3 /min -.98 in 3 /min with port valves, p= bar - 45 psi cm 3 /min -.8 in 3 /min Mineral oil with seals NBR (BUNA-N) from - C to 8 C - from -4 F to 76 F with seals FPM (VITON) from - C to 8 C - from -4 F to 76 F Viscosity operating range min. from 5 to 75 mm /s - from 5 to 75 cst mm /s - cst max. 4 mm /s - 4 cst Contamination level max. -/8/5 - ISO 446 - NAS 638 class 9 Environmental temperature for working conditions without solenoid operated unloader valve from - C to 6 C ( ) - from -4 F to 4 F ( ) with solenoid operated unloader valve from - C to 4 C ( ) - from -4 F to 4 F ( ) Environmental from +.8 to +. bar - from +.6 to 6 psi pressure for working conditions NOTES: ( ) According to NFPA T.6.., fatigue rating verified for million cycles on 6 sample valves with test Pressure =.3 x Max. pressure indicated - ( ) DPC3X can operate with gases with an ignition temperature above 35 C - 75 F and powders with an ignition temperature above 3 C - 66 F. Standard thread REFERENCE STANDARD THREAD ACCORDING TO BSP UN-UNF ISO 8/ ISO 63 BS 779 ANSI B. unified PORTS BSP UN-UNF P inlet G 3/4 /6- (SAE ) A and B ports G / 7/8-4 (SAE) T outlet G 3/4 /6- (SAE ) CAVITY DIMENSION ACCORDING TO ISO 79 96 SAE DIN 385-, X or Y shape J96 NOTES ( 3 ): Standard pressure series - ( 4 ): For pressure up to 35 bar (5 psi) LS Load Sensing G /4 9/6-8 (SAE 6) V pilot G /4 9/6-8 (SAE 6) depends on inlet section type: V pilot see pages from 4 to 7 ( 5 ) L drain G /4 7/6- (SAE 4) M pressure gauge G /4 9/6-8 (SAE 6) Hydraulic control ports G /4 9/6-8 (SAE 6) NOTES ( 5 ): ATTENTION! V pilot port requires dedicated joints; please see Inlet section pages. 5
DPC3X ATEX version ATEX directive introduction ATEX 94/9/EC Directive - ATEX 4/34/UE The ATEX 94/9EC Directive (and the release ATEX 4/34/UE) is applied to the manufacture specifications of all those products destined to be used in potentially explosive atmosphere caused by the dangers deriving from the presence of dust or gas with the aim to reduce the risk of use that could be derived. An explosive atmosphere according to this directive is made up from a mixture of inflammable substances (as gas, vapours, mists and dust) with air in determined atmospheric conditions in which, after triggering, the combustion propagates together with unburned mixture. An atmosphere susceptible to transforming into a an explosive atmosphere because of local and/or operative conditions is defined potentially explosive atmosphere. To define a conformity evaluation procedure adequate for this directive, the manufacturer must, on the basis of the declared use, establish the products functioning conditions (this means to say, envision the type of working area, the type of the explosive mixture with which it will come into contact and the level of probability that an explosive atmosphere verifies itself): successively he must establish to which Group the product belongs and determine the category inside the group. Areas With the Atex 99/9/EC Directive (For the safety of workers) the working conditions in which products in compliance with Atex 99/4/EC Directive will function are indicated here.these are expressed in Areas and defined according to the level of probability that a potentially explosive atmosphere is verified, respectively for every type of atmosphere (gas-air mix or dust-air mix). Area and Places in which an explosive atmosphere is constantly present or present for long periods or frequently. Area and Places in which an explosive atmosphere is probable. It is verified in normal functioning and exercise conditions. Area and Places in which an explosive atmosphere has low probability of being verified or, if it occurs only lasts for a brief period of time. Gas-Air-type explosive mixture (G) The products destined to work in environments characterized by this type of explosive atmosphere will be respectively indicated for Area, or depending on the Group and category of origin (see below) and are marked with the letter G. Dust-Air-type explosive mixture (D) The products destined to work in environments characterized by this type of explosive atmosphere will be respectively indicated for Area, or depending on the Group and category of origin (see below) and are marked with the letter D. 6
ATEX version DPC3X ATEX directive introduction Group I Includes the appliances destined to be used in underground jobs in the mines and their surface plants, exposed to the risk of the release of firedamp and/or combustible dust. The sub-division into categories depends on the fact if the power supply must be interrupted or not if an explosive atmosphere manifests due to a mixture of air and gas, vapours mists (D) or a mixture of air and dust (G). Category M: Very high protection level These products must be able to remain operative, for safety reasons, in the presence of an explosive atmosphere and present specific performances or protection configurations for breakdown in case of explosion. Category M: High protection level The power supply to these products must be interrupted in the presence of an explosive atmosphere. Protection means must be incorporated to guarantee the level of protection during normal functioning and also in oppressive working conditions or resulting from great stress. Group II Includes appliances destined to be used in different environments (from the mines) in which there is a probability that an explosive atmosphere manifests itself. Their subdivision into categories depends on two fators: the place, where the product will be used and if the probability that a potentially explosive atmosphere, owing to the mixture of air and gas, vapours, mists (D) and the mixture of air and dust (G), comes about in a constant or occasional manner and if it does occur, does this possibility remain for long or brief period of time. Category : Very high protection level These products must be planned to function in compliance with operative parameters established by the Manufacturer in environments in which there is a high probability that explosive atmospheres are always detected or manifest often or for long periods of time. They must present specific performances or protection configurations for breakdown in case of explosion. Category : High protection level These products must be planned to function in compliance with operative parameters established by the Manufacturer in environments in which there is a high probability that explosive atmospheres can manifest. Protection against explosions relative to this cate-gory must Function in a way to guarantee the required safety level even in the presence of functioning defects of the appliances or in dangerous operative conditions, which frequently must be taken into consideration. Category 3: Normal protection level These products must be planned to function in compliance with operative parameters established by the Manufacturer in environments in which there is a slight probability that explosive atmospheres can manifest, and however only rarely or for a brief period of time. This type of product belonging to the category in question must guarantee the safety level required in normal functioning condition. 7
DPC3X ATEX version Explosion risk assessment Equipment description The DC3 sectional control valves, manufactured by Walvoil S.p.A, included in the equipment definition stated by the Directive 94/9/CE, published on March 994 and effective form 7//3 and then replaced by the Directive ATEX4/34/UE published on Feb-ruary 6th and which is to be effective from April th 6. The Directive defines the equipment as [ ] machines, materials, fixed or mobile devices, control components, instrumentation and detection or prevention systems which, separately or jointly, are intended for the generation, transfer, storage, measurement, control and conversion of energy and/or the material processing and which are capable of causing an explosion because of their own potential sources of ignition. According with this definitions the Walvoil SpA DPC3X sectional control valves, are not able to work properly if they are not previously connected to a hydraulic feeding line and in some cases to an electrical one. The Walvoil SpA DPC3 Series, in compliance with the Directive ATEX, is composed by different valve types whose dimensions may change but not their working principle. Electric/hydraulic components installed on Walvoil DPC3X, are to be considered as commercial components, marked ATEX, purchased from different suppliers and suitable to the area oh use. Please find in this catalogue the environmental conditions for DPC3X sectional valve assembling. Use conditions Walvoil DPC3 valves are manufactured for open/closed center hydraulic circuits and they are specifically designed specifically for Mobile Machines Applications. The standard operating conditions are the environmental ones, with atmospheric pressure from +.8 to +. bar and environmental temperature from - C to +6 C (from -4 F to 4 F); if the MS unloader valve is installed, the range of environmental temperature is limited from - C to +4 C (from -4 F to F). The temperature range of the operating fluid is from - C to +8 C (from -4 F to 76 F). Because of the possibility that this equipment is used in environments classified for the presence of flammable gases or combustible dusts, or in mines and in their surface plants, which may be exposed to the risk of firedamp and/or combustible dusts, it is necessary to elaborate an accurate risk assessment in order to avoid that this equipment becomes an of ignition source. This risks is aimed at makingthe equipment suitable for installation in an environment classified as AREA for the presence of flammable gases or as AREA for the presence of combustible dust, or in mining environment which may be po-tentially explosive: category II G category II D category I M (Main) reference sources Legislative Body Directive ATEX 94/9/CE: Directive of European Parliament and of the Council of the 3 March 994 on the approximation of the laws of the Member States concerning equipments and protective systems intended for use in potentially explosive atmosphere DPR 3/3/98n 6: Regulation which contains the standards to actuate the Directive 94/9/CE. Directive ATEX 4/34/UE of 6 February 4 concerning the harmonization of the laws of the Member States related to the equipment and the systems of protection intended to be used in a potentially explosive atmosphere. Standard Body UNI EN 3463-: 9: Non-electrical equipment for use in potentially explosive atmosphere Part : Basic concepts and requirements. UNI EN 3463-5: : Non-electrical equipment for use in potentially explosive atmosphere Part 5: Protection by constructional safety c. UNI EN 7-: : Explosive atmospheres: Explosion prevention and protection - Part : Basic concepts and methodology. UNI EN 443-: Hydraulic Fluid Powers General rules and safety requirements for sys-tems and their components. 8
ATEX version DPC3X Explosion risk assessment Risks analisys Different types of explosion risks are linked to the DPC3X working conditions. This is equipment has to be assembled in environments classified as AREA or AREA or in M category mining environments, that is to say environments where the presence of combustible gases in air or of flammable dust, which may form a potentially explo-sive airborne cloud, is to be considered occasional during the regular plant working. From this point of view, also in case of predictable malfunction, the equipment, has not to be an ignition source for the possible present explosive atmosphere. Walvoil supplies DPC3X in category G, D and for some product types in category M as well. Therefore with reference to the service and maintenance manual, please note that the installer and the user are requested to choose all the certified mechanical and electrical components, to be assembled on the equipment accordingly: category G (ZONE ), or category D (ZONE ), or category M. In case of maintenance or cleaning operations, the user has to be sure to be far from a potentially explosive area. Ignition hazard assessment As for the possible ignition risk assessment, the analysis of the different equipment constructive drawings and the analysis of their functionality have seen carried out, by considering all the predictable malfunctions in compliance with the Directive. In particular, all the possible ignition sources (suggested by the standard UNI EN 7- and according to UNI EN 3463-) have seen considered and, for each of them, the technical or operational measures adopted in order to make the ignition source not effective. More in details (with reference to the selected categories): all the relevant parts, exposed to the explosion risk, have been evaluated for the risk from falling material or accidental impact and they meet the essential requirements (see impact test); the determination of the surface temperature and of the electrostatic risk, the service and maintenance manual indications, the marking and the application of the preventive and protective measures for all the potential ignition sources. The DPC3X valves will be supplied in ATEX configuration with a maximal surface temperature defined with a wider range that the one verified during the tests. The DPC 3X valves will be supplied as follows: Marking: II G c T4 II D c T3 C Without MS unloader valve mounted on the control valve: I M c All the accessories arw marked ATEX of a category suitable to the area of use and of limit temperature class T4 e T3 C. Working AREA: ZONE or ZONE or M 9
DPC3X ATEX version Dimensional data and performance 3 9.6 54.5.5 37..46 8 3.9 6.63 48. 5.97 6.63 53.9.39 5.97 Ø 8.5 Ø.33 43.5. 9.35 8.3 3.94 8.3 4.7.9 6 4.57 33.5.3.43 33.3 L A A P 93.5.56 LS 33.5.3 B B T 45.5.79 3.4 5.3 5 5.98 8.3 E F product name product code customer code production allotment ATEX category environmental temperature Type manufacturer reference DPC3X/ 6...... PA5568/4 II G c T4 - II c T3 c - I M c T amb - +6 C T fluid - +8 C Via Adige 3/D 44 Reggio E. Italy fluid temperature E F Weight mm in mm in Kg lb DPC3/ 84 7.4 7.87.4 7.3 DPC3/ 3 9.3 48 9.76 9.4 4.8 DPC3/3 8. 96.65 5.3 55.8 DPC3/4 38.9 344 3.54 3. 68.3 DPC3/5 376 4.8 39 5.43 36.5 8.5 DPC3/6 44 6.69 44 7.3 4.6 93.9 CE mark DPC3/7 47 8.58 488 9. 48.7 7. DPC3/8 5.47 536. 54.8. DPC3/9 568.36 584.99 6.9 34. DPC3/ 66 4.5 63 4.88 67. 48. DATAMATRIX ATEX mark Pressure Pressure P T Pressure drop inlet compensator (margin pressure) 4 (bar) 3 8 6 4 3 (US gpm) (psi) 5 4 3 3 6 9 5 (l/min) Flow 4 (bar) 3 A(B) T pressure drop (standard spool @ max.stroke) 8 6 4 3 without compensator with compensator 8 th section st section l/min 6.4 US gpm 3 l/min 34.3 US gpm (US gpm) (psi) 5 4 3 3 6 9 5(l/min) Flow
ATEX version DPC3X Complete section ordering codes Valve type DPC3X-E/3/BR-S-ELNXFL/C-S8EZ3TXFL-LG/C-S8EZ3TXFL-LG/... /RF3-...-VDC-TAX-LTXE Pump stand-by Nr. of working sections Datamatrix code (on plate) <SB-CVNX-DAMA-MNP-ADC-MUM-DDC> 3 4 Marking with progressive number (on plate) Valve threading Voltage 5 Product plate: according to ATEX directive Marking layout 6 The valve is supplied painted, as standard, with one coat of Primer black antirust paint. Painting special procedure. Declaration of Conformity attached Service manual attached Testing data acquisition Section without unloader valve Assembling kit Section with unloader valve Assembling kit 3 Tie rod tightening wrench 3-3 Nm ( lbft) NOTE - Sections listed below are for example; for further section configurations and ordering codes please ask to Sale Department. Inlet section Closed Center circuit TYPE: DPC3/BN-S DESCRIPTION: With secondary pressure control system and pressure reducing valve, with L.S. pressure relief valve. TYPE: DPC3/BR-S-ELNXFL-VDC DESCRIPTION: As previous one, with pressure reducing valve, and VDC solenoid operated unloader valve Open Center circuit TYPE: DPC3/BN-S DESCRIPTION: With 3-way compensator and L.S. pressure relief valve, without pressure reducing valve TYPE: DPC3/BR-S-ELNXFL-VDC DESCRIPTION: As previous one, with pressure reducing valve, and VDC solenoid operated unloader valve. For unloader valve specification, see page Working section TYPE: DPC3/C-S8EZ3TXFL-LG-VDC DESCRIPTION: With way compensator, double acting spool for 6 l/ min (6 US gpm), proportional electrohydraulic control with lever TYPE: DPC3/C-S8EZ3TXFL-LG.UTUTSTST-VDC DESCRIPTION: As previous one, arranged for port valves and L.S. relief valves For more controls according to ATEX directive please see from pages 4 to 7 3 Outlet section TYPE DPC3/RF DPC3/RF DPC3/RD3 DESCRIPTION Without ports; for valve with mechanical control Without ports, internal drain; for valve with hydraulic control With P and T ports (plugged), LS port, L external drain; for valve with electrohydraulic. control
DPC3X ATEX version Inlet section Solenoid operated L.S. unloader valve 5 4.3 E LT ELN F ELP G C Valve type Dim. C mm in ELN 65.5.58 ELP 88.5 3.48 ELV 88.5 3.48 ELT 9 3.58 ELV ELT Valve features Max. flow................: 4 l/min (.6 US gpm) Max. pressure.............: 38 bar (55 psi) Internal leakage...........:.5 cm 3 /min @ bar (.5 in 3 /min @ 35 psi) Coil features Nominal voltage...........: VDC / 4 VDC ±% Power rating..............: 9 W Coil insulance.............: Class H (8 C - 356 F) Weather protection.........: IP66 Insertion................: % Legenda ELN: without emergency ELP: push button emergency override ELV: screw emergency override ELT: push&twist emergency override LT: valve blanking plug Wrenches and tightening torques E = wrench - 4 Nm (7.7 lbf) F = wrench 4-3 Nm ( lbf) G = manual tightening
ATEX version DPC3X Working section "A" side spool control kit With spring return to neutral position: 8 type It is supplied with standard spring A type (see force-stroke diagram); available with stronger spring C type (8MC code: 5V83). 6.63 Force vs. Stroke diagram -.5 -. -.5 -. -.5 -.3(in) 7.5.8 X Force (N).5..5..5 5 9 6 3 Spring C type Spring A type (in) 3 (lbf) 4 6 8 Wrenches and tightening torque X = allen wrench 5-9.8 Nm (7. lbf) 3 4 5 6 7 pos. (mm) - - -3-4 -5-6 -7 pos. (mm) Stroke Spring A type = from 35.6 N (8 lbf) to 8.8 N (8.4 lbf) Spring C type = from 8.3 N (8.5 lbf) to 6.8 N (6.3 lbf) With detent in 4 th position (pos.3), for floating circuit: 3 type F, G or FV type working sections and floating circuit 5 type spool are requested for..5.4 X 3 7.5.8 Y 45.5.79 Features Detent force (±%)..... : 3 N (7 lbf) Release force (±%).... : N (4.7 lbf) Wrenches and tightening torque X = allen wrench 5-9.8 Nm (7. lbf) Y = wrench 3-4 Nm ( 7.7 lbf) 3
DPC3X ATEX version Working section "A" side spool control kit Proportional hydraulic controls: IMO type 3. G/4 nr. threads VB VA 7.6 VA VB 7.5.8 X 7.5.8 Features Max. pressure.............: 5 bar (75 psi) 4.94 48.89 Wrenches and tightening torque X = allen wrench 5-9.8 Nm (7. lbf) Y = wrench 3-4 Nm ( 7.7 lbf) Pressure (bar) 5 5 Stroke vs. Pressure diagram -.5 -. -.5 -. -.5.5..5..5 spool dead band (in) (psi) -7-6 -5-4 -3 - - 3 4 5 6 7 (mm) position Stroke position 5 5 5 Pilot pressure.5..5..5.3 (in) 4 (psi) 35 bar (58 psi) (bar) 5 3 Suggested pressure control curve: type 5.3 bar ( psi) 4.3 bar (63 psi) 7.5 mm (.9 in) 7.6 mm (.3 in) 4 3.85 mm (.33 in) 4 6 8 (mm) Pusher stroke 4
ATEX version DPC3X Working section "A" side spool control kit Proportional electrohydraulic control: 8EZ3TXFL type Following specifications are measured with: mineral oil of 46 mm /s (46 cst) viscosity at 4 C (4 F) temperature, C (6 F) environmental temperature, standard spools, connecting P A B T ports without flow multiplication, VDC and 4 VDC nominal voltage with ± % tolerance. ±5 78.74±.97 4±5.55±. Features VDC 4 VDC Coil impedance.............. : 5.3 Ω. Ω Max. operating current........ :.5 A.75 A Min. flow control signal........ : 5 ma 5 ma Max. flow control signal........ : ma 5 ma 3 9.6 3.5 8. X Z EVA A port EVB B port Hysteresis max. () (external drain). : < % Time response (from % and from % ).......... : < 5 ms Dither frequency (high frequency). : Hz ( ma) Insertion.................. : % Coil insulance ()............. : ---------- Connection type............. : flying leads Weather protection........... : IP69K Max. pressure............... : 5 bar (75 psi) Max. back pressure on drain..... :.5 bar (36 psi) 7.5.8 Note () For the calculation rules please see "Appendicies" section on page 7. Note () Not availbale; operating temperature according to ATEX directive. A B EVA EVB 85 3.35 Wrenches and tightening torque X = allen wrench 5-9.8 Nm (7. lbf) Z = allen wrench 3-5 Nm (3.7 lbf) Stroke vs. Current diagram 4 (ma@vdc) 5 Current 7 35 -.5 -. -.5 -. -.5.5..5..5 5/5 ma /5 ma spool dead band (in) 7 (ma@4vdc) 55 35 75-7 -6-5 -4-3 - - 3 4 5 6 7 (mm) position Stroke position 5
DPC3X ATEX version Working section "B" side spool control kit Cast iron lever box; LG type 3 4.65 X 45 6 3' 3 5 3 6 3' 3 3 3 W Z Y 39.55 47.85 7.5.8 3 3 B 87 3.43.83 4 Lever assembly position Please see page 9 for specification in working section description M8 Wrenches and tightening torque X = allen wrench 5-9.8 Nm (7. lbf) Y = allen wrench 3 Z = wrench - 9.8 Nm (7. lbf) W = allen wrench 4-6.6 Nm (4.9 lbf) 6
ATEX version DPC3X Installation Main rules The DPC Series valves are assembled and tested as per the technical specifications of this catalogue. Before the final installation on your equipment, please follow the below recommendations: the valve can be assembled in any position; in order to prevent body deformation and spool sticking mount the product on a flat surface; In order to prevent the possibility of water entering the spool control kit, do not use high pressure washdown directly on the valve; prior to painting, ensure plugs on normally open ports are tightly in place. WARNING: for painting refer always to the guidelines included in the User and Maintenance Manual supplied with the product per indicazioni dettagliate in merito all'installazione e all'impiego consultare sempre il Manuale d'uso e manutenzione. for detailed instructions about the installation and use always refer to the User and Maintenance Manual. B A L T p V Ls V FITTINGS TIGHTENING TORQUE - Nm / lbft THREAD TYPE P inlet port A and B workports T outlet port LS signal port V pilot ports* L drain port Hydraulic control ports BSP G 3/4 G / G 3/4 G /4 G /4 G /4 With O-Ring seal 9 / 66.4 5 / 36.9 9 / 66.4 5 / 8.4 5 / 8.4 5 / 8.4 With copper washer 9 / 66.4 6 / 44.3 9 / 66.4 3 /. 3 /. 3 /. With steel and rubber washer 7 / 5.6 6 / 44.3 7 / 5.6 6 /.8 6 /.8 6 /.8 UN-UNF NOTE These torque are recommended. Assembly tightening torque depends on many factors, including lubrication, coating and surface finish. /6- (SAE ) 7/8-4 (SAE ) /6- (SAE ) 9/6-8 (SAE 6) 9/6-8 (SAE 6) 9/6-8 (SAE 6) With O-Ring seal 95 / 7 5 / 36.9 95 / 7 3 /. 3 /. 3 /. (*) V port is M4x.5 threading: tightenìng torque value is the same of G/4 thread 7
DPC3X ATEX version 8
9
st edition March 6 WWW.WALVOIL.COM