Riggers and Associated Parts Pins are all 13mm shafts, with 8x27mm tops, and supplied with washers, nuts and spacers. Rig 1A-sc 13x105mm shaft, 10x55mm base - for scull & sweep Carbon wing S/S yes 28.57 31.43 Rig 1B-sc 13x105mm shaft, 10x30mm base - for L block S/S yes 28.57 31.43 Rig 1C-sc 13x105mm shaft, 12x55mm base - for Euro, Gull, scull & sweep Al. S/S yes 28.57 31.43 Rig 1D-sc 13x105mm shaft, 12x30mm base S/S no 28.57 31.43 Rig 1A-sw 13x120mm shaft, 10x55mm base S/S no 28.57 31.43 Rig 1B-sw 13x120mm shaft, 10x30mm base - for L block S/S yes 28.57 31.43 Rig 1C-sw 13x120mm shaft, 12x55mm base - for Euro, Gull wing S/S yes 28.57 31.43 Rig 1D-sw 13x120mm shaft, 12x30mm base S/S yes 28.57 31.43 Rig 3A 13x100mm shaft - for carbon tube and ali back rigger S/S yes 21.43 23.57 Rig 4 Complete C bracket for carbon tube rigger S/S yes 17.86 19.64 Rig 4A C bracket (only) for carbon tube rigger S/S yes 14.29 15.71 Rig 4B Bolts to fix C bracket to carbon tube rigger (1 set) S/S yes 5.36 5.89 Rig 8A O shape spacer for pin 2mm (pack of 100 pieces) Pla yes 5.36 5.89 Rig 9 C bracket for Al. back rigger, including back plate and 2 bolts Al. yes 14.29 15.71 Pin wedges are to change the angle (pitch) of the pin. Either fore/aft, lateral, or both. 2 pieces must be used, one above and one below the rigger block, inserted in opposing directions. Rig 10 Pin wedges, 2 each of 0.5, 1.0, 1.5, 2.0, 2.5 degrees Pla no 2.86 3.14 Rigger height wedges are inserted between the saxboards and the foor of the rigger, and will increase or decrease the work height. Pin angle will also change, but pin wedges can be used to correct this. Rig 11 Rigger height wedges, 1 each of 0.5, 1.0, 1.5, 2.0, 2.5 degrees Pla no 3.57 3.93 Aluminium Riggers Rig 20A 3 stay scull rigger frame, with European style 12mm block Al. yes 142.86 157.14 Rig 21A 3 stay sweep rigger frame, with European style 12mm block Al. yes 142.86 157.14 Rig 20C 3 stay scull rigger frame, for L style block Al. yes 142.86 157.14 Rig 21C 3 stay sweep rigger frame, for L style block Al. yes 142.86 157.14 Rig 22A Non-adjustable L block for pins 1B-sc and 1B-sw Al. yes 19.64 21.61 Rig 22B Adjustable L block for 10mm pins Al. no NA NA Rig 23 2 stay scull back rigger frame Al. yes 142.86 157.14 Rig 24 2 stay sweep back rigger frame Al. yes 142.86 157.14 Rig 29 Scull wing rigger Al. yes 320.00 352.00 Rig 30 Sweep wing rigger Al. yes 270.00 297.00 Rig 31 2 stay scull gull rigger frame Al. yes NYA NYA Rig 32 2 stay sweep gull rigger frame Al. yes NYA NYA
Carbon Riggers Rig 25 2 stay scull carbon tube rigger with C bracket (back rigger only) Carb yes 392.86 432.14 Rig 26 2 stay sweep carbon tube rigger with C bracket (back rigger only) Carb yes 428.57 471.43 Rig 27 Scull carbon wing rigger with European stye 10mm block Carb yes 780.00 858.00 Rig 28 Sweep carbon wing rigger with European stye 10mm block Carb yes 642.86 707.14 Topstays are made from 2 parts, the long pipe and (shorter) extender. The long pipe has bow and stroke side, but is the same for ALL boats (incl. 1x, 4x+, 4+, 8+ etc), but needs to be cut to the right length by the customer. There is a different extender for each boat class, but bowside and strokeside are the same. Rig 40b Long pipe for backstay with 8.5mm hole - bowside Al. yes 17.86 19.64 Rig 40s Long pipe for backstay with 8.5mm hole - strokeside Al. yes 17.86 19.64 Rig 41-1x Extender for backstay for 1x complete Al. yes 21.43 23.57 Rig 41-xx Extender for backstay for 2x complete Al. yes 21.43 23.57 Rig 41-4x Extender for backstay for 4x complete Al. yes 21.43 23.57 Rig 41-2- Extender for backstay for 2- complete Al. yes 21.43 23.57 Rig 41-4+/- Extender for backstay for 4+/- complete Al. yes 21.43 23.57 Rig 41-8+ Extender for backstay for 8+ complete Al. yes 21.43 23.57 Rig 41-w Extender for backstay for wing rigger boats complete Al. yes 21.43 23.57 Rig 45A Rigger plates for saxboards, 2x60x60mm, un-drilled small Carb yes 4.00 4.40 Rig 45B Rigger plates for saxboards, 2x70x100mm, un-drilled big Carb yes 4.00 4.40 Rigger bolts have square "necks" which fit the square hole in the rigger bolt washers. Because the inside and outside surfaces of ribs (shoulders) are not parallel, the head of the bolt needs to be bent, relative to the shaft. Rig 50-35 6x35 rigger bolts S/S no 2.86 3.14 Rig 50-40 6x40 rigger bolts S/S no 2.86 3.14 Rig 50-45 6x45 rigger bolts S/S no 2.86 3.14 Rig 50-50 6x50 rigger bolts S/S no 2.86 3.14 Rig 50-60 6x60 rigger bolts S/S no 2.86 3.14 Rig 50-80 6x80 rigger bolts S/S no 3.21 3.54 Rig 50-100 6x100 rigger bolts S/S no 3.57 3.93 Rig 50-35pb 6x35 rigger bolts - pre bent bolt head S/S yes 3.57 3.93 Rig 50-40pb 6x40 rigger bolts - pre bent bolt head S/S yes 3.57 3.93 Rig 50-45pb 6x45 rigger bolts - pre bent bolt head S/S yes 3.57 3.93 Rig 50-50pb 6x50 rigger bolts - pre bent bolt head S/S yes 3.57 3.93 Rig 50-60pb 6x60 rigger bolts - pre bent bolt head S/S yes 3.57 3.93 Rig 50-80pb 6x80 rigger bolts - pre bent bolt head S/S yes 3.93 4.32 Rig 50-100pb 6x100 rigger bolts - pre bent bolt head S/S yes 4.29 4.71 Rigger bolt washers are sold flat. They should be fitted to the rib/shoulder with a rigger bolt that is tightened. Then tap the "ears" of the washer around the rib/shoulder with a hammer. Rig 51 Rigger bolt washer (square hole) - not bent S/S yes 2.50 2.75 QUICKR Quick Release Option No 100.00 110.00
Stretchers and Associated Products For attaching the 25mm strethcer pipe, 3 U brackets are used. Every stretcher has 3 rows of 5 predrilled holes for Str 1-235 Stretcher board - standard - 235mm Carb no 125.00 137.50 Str 1-240 Stretcher board - standard - 240mm Carb no 125.00 137.50 Str 1-245 Stretcher board - standard - 245mm Carb yes 125.00 137.50 Str 1-250 Stretcher board - standard - steering - 250mm Carb yes 125.00 137.50 Str 1-260 Stretcher board - standard - steering - 260mm Carb yes 125.00 137.50 Str 1-270 Stretcher board - standard - steering - 270mm Carb yes 125.00 137.50 Str 1-280 Stretcher board - standard - steering - 280mm Carb no 125.00 137.50 Str 1-290 Stretcher board - standard - steering - 290mm Carb no 125.00 137.50 Str 1-300 Stretcher board - standard - steering 300mm Carb no 125.00 137.50 Complete stretchers include 16mm Al pipe, 1 of Str3, 2 of Str3A, 2 of square neck bolts, 2 of U brackets with bolts, 3 of bolts for holding shoe plate. (T bolts, 25mm Al pipe not included) Str 1-235c Stretcher complete - standard - 235mm Carb no 160.00 176.00 Str 1-240c Stretcher complete - standard - 240mm Carb no 160.00 176.00 Str 1-245c Stretcher complete - standard - 245mm Carb yes 160.00 176.00 Str 1-250c Stretcher complete - standard - steering - 250mm Carb yes 160.00 176.00 Str 1-260c Stretcher complete - standard - steering - 260mm Carb yes 160.00 176.00 Str 1-270c Stretcher complete - standard - steering - 270mm Carb yes 160.00 176.00 Str 1-280c Stretcher complete - standard - steering - 280mm Carb no 160.00 176.00 Str 1-290c Stretcher complete - standard - steering - 290mm Carb no 160.00 176.00 Str 1-300c Stretcher complete - standard - steering 300mm Carb no 160.00 176.00 Str 2 16mm pipe for base of stretcher (150mm long) Al. yes 3.50 3.85 Str 3 is used to attach the base of the stretcher to the stretcher track. Str 3 "C" type track runner for 16mm diameter pipe, shark tooth Pla yes 3.50 3.85 Str 3A (2 of) holds the 16mm pipe to the back of the stretcher, which is used to adjust stretcher angle (rake) Str 3A "C" type track runner for 16mm diameter pipe, flat face Pla yes 3.50 3.85 Str 4 Square neck bolts, 40mm, with washers and wing nuts (for Str 5) S/S yes 5.00 5.50 Str 5 6 x 60mm elongated washer for stretcher S/S yes 5.00 5.50 Str 6 U bracket for holding 25mm ali pipe to stretcher S/S yes 3.50 3.85 Str 7 4mm bolt (with washer and locking nut) for U bracket (Str 6) S/S yes 1.50 1.65 Str 8 Stretcher track, shark tooth type - 250mm Pla yes 6.50 7.15 Str 9 Stretcher track, shark tooth type - 320mm Pla no 11.00 12.10 Str 10 Insert type runner for 25mm diameter pipe Pla yes 3.50 3.85 Str 11 Flat type track runner for keel (not used on ) Pla no 4.00 4.40 Str 12 "C" type track runner for 25mm diameter pipe Pla yes 5.00 5.50 Str 15 Long T bolt 6x45mm S/S no 4.00 4.40 Str 16 Short T bolt 6x30mm S/S yes 4.00 4.40 Str 17 25mm cross pipe, 1.5m length uncut, silver anodized Al. yes 25.00 27.50 Str 18 6mm tube nut (short) S/S yes 4.50 4.95
Carbon Shoe Plates Str31, 32 and 33 (except 33A) have 1 row of 7 holes down the center. And any 2 of these holes can be used to attach the shoe plate to the stretcher. As there are no holes on the outside edges of the shoe plates, shoes are positioned wider than with most other makes of boats, which allows more comfort and better application of power. Str 31-235 Shoe plate for "square" shoes - 235mm Carb no 55.00 60.50 Str 31-240 Shoe plate for "square" shoes - 240mm Carb no 55.00 60.50 Str 31-245 Shoe plate for "square" shoes - 245mm Carb yes 55.00 60.50 Str 31-250 Shoe plate for "square" shoes - 250mm Carb yes 55.00 60.50 Str 31-260 Shoe plate for "square" shoes - 260mm Carb yes 55.00 60.50 Str 31-270 Shoe plate for "square" shoes - 270mm Carb yes 55.00 60.50 Str 31-280 Shoe plate for "square" shoes - 280mm Carb no 55.00 60.50 Str 31-290 Shoe plate for "square" shoes - 290mm Carb no 55.00 60.50 Str 31-300 Shoe plate for "square" shoes - 300mm Carb no 55.00 60.50 Str 32-235 Shoe plate for Adidas shoes - 235mm Carb no 55.00 60.50 Str 32-240 Shoe plate for Adidas shoes - 240mm Carb no 55.00 60.50 Str 32-245 Shoe plate for Adidas shoes - 245mm Carb no 55.00 60.50 Str 32-250 Shoe plate for Adidas shoes - 250mm Carb no 55.00 60.50 Str 32-260 Shoe plate for Adidas shoes - 260mm Carb no 55.00 60.50 Str 32-270 Shoe plate for Adidas shoes - 270mm Carb no 55.00 60.50 Str 32-280 Shoe plate for Adidas shoes - 280mm Carb no 55.00 60.50 Str 32-290 Shoe plate for Adidas shoes - 290mm Carb no 55.00 60.50 Str 32-300 Shoe plate for Adidas shoes - 300mm Carb no 55.00 60.50 Str33 is for those people who want to attach other makes of shoe, or otherwise customize their shoe plate. Str 33-235 Shoe plate with no shoe holes - 235mm Carb no 55.00 60.50 Str 33-240 Shoe plate with no shoe holes - 240mm Carb no 55.00 60.50 Str 33-245 Shoe plate with no shoe holes - 245mm Carb no 55.00 60.50 Str 33-250 Shoe plate with no shoe holes - 250mm Carb no 55.00 60.50 Str 33-260 Shoe plate with no shoe holes - 260mm Carb no 55.00 60.50 Str 33-270 Shoe plate with no shoe holes - 270mm Carb no 55.00 60.50 Str 33-280 Shoe plate with no shoe holes - 280mm Carb no 55.00 60.50 Str 33-290 Shoe plate with no shoe holes - 290mm Carb no 55.00 60.50 Str 33-300 Shoe plate with no shoe holes - 300mm Carb no 55.00 60.50
Steering Shoes Plates and Parts The steering system is very simple, and must be used with a stretcher, and can then be used in nearly all makes of boats. The strethcer position can be adjusted without having to adjust the rudder wire length. Str 41-250 Steering shoes plate - for shoes - complete - 250mm Carb yes 95.00 104.50 Str 41-260 Steering shoes plate - for shoes - complete - 260mm Carb yes 95.00 104.50 Str 41-270 Steering shoes plate - for shoes - complete - 270mm Carb yes 95.00 104.50 Str 42-250 Steering shoes plate - for Adidas shoes - complete - 250mm Carb no NA NA Str 42-260 Steering shoes plate - for Adidas shoes - complete - 260mm Carb no NA NA Str 42-270 Steering shoes plate - for Adidas shoes - complete - 270mm Carb no NA NA Str 43-250 Steering shoes plate - no shoe holes - complete - 250mm Carb no 95.00 104.50 Str 43-260 Steering shoes plate - no shoe holes - complete - 260mm Carb no 95.00 104.50 Str 43-270 Steering shoes plate - no shoe holes - complete - 270mm Carb no 95.00 104.50 Str 44 Cable guide Pla yes 7.00 7.70 Str 44A Cable guide holder (with screws, washers, nuts) S/S yes 2.50 2.75 Str 45 Cable (1m) Pla yes 7.00 7.70 Str 46B Steering finger for "square" shoes - with Str47 Al. yes 35.00 38.50 Str 46C Steering finger for Adidas shoes - with Str47 Al. yes 35.00 38.50 Str 46D Steering finger with no shoe holes - with screw for fixing wire Al. yes 35.00 38.50 Str 47 Clamp (to clamp wire to finger) with bolt, washer, wing nut Pla yes 9.00 9.90 Str 48 Large washer for under steering finger Pla yes 2.00 2.20 Str 49 Square neck bolt, washer, locking nut for steering finger (18mm) S/S yes 3.00 3.30 Shoes Str62 have a very simple, rectangular hole pattern of 35mm across, 25mm down. 5mm screws are supplied with shoes. Str 62-37 Shoes, "square" holes - EUR37, UK4 1/4, US4 3/4, JPN22.75 Pla yes 80.00 88.00 Str 62-38 Shoes, "square" holes - EUR38, UK5, US5 1/2, JPN23.5 Pla yes 80.00 88.00 Str 62-39 Shoes, "square" holes - EUR39, UK5 3/4, US6 1/4, JPN24.25 Pla yes 80.00 88.00 Str 62-40 Shoes, "square" holes - EUR40, UK6 1/2, US7, JPN25 Pla yes 80.00 88.00 Str 62-41 Shoes, "square" holes - EUR41, UK7 1/4, US7 3/4, JPN25.75 Pla yes 80.00 88.00 Str 62-42 Shoes, "square" holes - EUR42, UK8, US8 1/2, JPN26.5 Pla yes 80.00 88.00 Str 62-43 Shoes, "square" holes - EUR43, UK8 3/4, US9 1/4, JPN27.25 Pla yes 80.00 88.00 Str 62-44 Shoes, "square" holes - EUR44, UK9 1/2, US10, JPN28 Pla yes 80.00 88.00 Str 62-45 Shoes, "square" holes - EUR45, UK10 1/4, US10 3/4, JPN28. Pla yes 80.00 88.00 Str 62-46 Shoes, "square" holes - EUR46, UK11, US11 1/2, JPN29.5 Pla yes 80.00 88.00 Str 62-47 Shoes, "square" holes - EUR47, UK11 3/4, US12 1/4, JPN30. Pla yes 80.00 88.00 Str 62-48 Shoes, "square" holes - EUR48, UK12 1/2, US13, JPN31 Pla yes 80.00 88.00 Str 62-49 Shoes, "square" holes - EUR49, UK13 1/4, US13 3/4, JPN31. Pla yes 80.00 88.00 Str 62-50 Shoes, "square" holes - EUR50, UK14, US14 1/2, JPN32.5 Pla yes 80.00 88.00 Str 62-51 Shoes, "square" holes - EUR51, UK14 3/4, US15 1/4, JPN33. Pla yes 80.00 88.00 Str 62-52 Shoes, "square" holes - EUR52, UK15 1/2, US16, JPN34 Pla yes 80.00 88.00 Str 62-53 Shoes, "square" holes - EUR53, UK16 1/4, US16 3/4, JPN34. Pla yes 80.00 88.00 Str 62-54 Shoes, "square" holes - EUR54, UK17, US17 1/2, JPN35.5 Pla yes 80.00 88.00
Seats and Associated Parts Sea 1-140 Single action seat - 140mm Carb no 180.00 198.00 Sea 1-160 Single action seat - 160mm Carb no 180.00 198.00 Sea 1-165 Single action seat - 165mm Carb no 180.00 198.00 Sea 1-170 Single action seat - 170mm Carb no 180.00 198.00 Sea 1-180 Single action seat - 180mm Carb yes 180.00 198.00 Sea 1-200 Single action seat - 200mm Carb no 180.00 198.00 Sea 1-210 Single action seat - 210mm Carb no 180.00 198.00 Sea 1-230 Single action seat - 230mm Carb yes 180.00 198.00 Sea 1-254 Single action seat - 254mm (10 inch) Carb no 180.00 198.00 Sea 1-260 Single action seat - 260mm Carb no 180.00 198.00 Sea 1-280 Single action seat - 280mm (11 inch) Carb yes 180.00 198.00 Sea 2-140 Single action seat - 140mm Wood no 130.00 143.00 Sea 2-160 Single action seat - 160mm Wood no 130.00 143.00 Sea 2-165 Single action seat - 165mm Wood no 130.00 143.00 Sea 2-170 Single action seat - 170mm Wood no 130.00 143.00 Sea 2-180 Single action seat - 180mm Wood no 130.00 143.00 Sea 2-200 Single action seat - 200mm Wood no 130.00 143.00 Sea 2-210 Single action seat - 210mm Wood no 130.00 143.00 Sea 2-230 Single action seat - 230mm Wood no 130.00 143.00 Sea 2-254 Single action seat - 254mm (10 inch) Wood no 130.00 143.00 Sea 2-260 Single action seat - 260mm Wood no 130.00 143.00 Sea 2-280 Single action seat - 280mm (11 inch) Wood no 130.00 143.00 Sea 10-140 Axels - 140mm Al. no 4.00 4.40 Sea 10-160 Axels - 160mm Al. no 4.00 4.40 Sea 10-165 Axels - 165mm Al. no 4.00 4.40 Sea 10-170 Axels - 170mm Al. no 4.00 4.40 Sea 10-180 Axels - 180mm Al. yes 4.00 4.40 Sea 10-200 Axels - 200mm Al. no 4.00 4.40 Sea 10-210 Axels - 210mm Al. no 4.00 4.40 Sea 10-230 Axels - 230mm Al. yes 4.00 4.40 Sea 10-254 Axels - 254mm (10 inch) Al. no 4.00 4.40 Sea 10-260 Axels - 260mm Al. no 4.00 4.40 Sea 10-280 Axels - 280mm (11 inch) Al. yes 4.00 4.40 Sea 11A Support for single action seats - high Pla no 6.50 7.15 Sea 11B Support for single action seats - standard Pla yes 5.00 5.50 Sea 12 Ball bearing wheel Pla yes 10.00 11.00 Sea 12-s Seat top - small (varnished) for 140, 160, 170, 180mm Wood no 75.00 82.50 Sea 12-m Seat top - medium (varnished) for 180, 200, 210 or 230mm Wood no 75.00 82.50 Sea 12-l Seat top - large (varnished) for 230, 254, 260, 280mm Wood no 75.00 82.50 Sea 13-265 Seat top- 265mm for 140, 160, 170, 180mm Carb yes 125.00 137.50 Sea 13-280 Seat top- 280mm wide for 180, 200, 210 or 230mm Carb yes 125.00 137.50 Sea 13-300 Seat top- 300mm wide for 230, 254, 260, 280mm Carb yes 125.00 137.50 Sea 14-800 Complete seat rail, silver anodised - 800mm Al. yes 20.00 22.00 Sea 14-850 Complete seat rail, silver anodised - 850mm Al. no 20.00 22.00 Sea 14Afl Black rail stopper - front left/ back right Pla yes 3.00 3.30 Sea 14Afr Black rail stopper - front right/ back left Pla yes 3.00 3.30 Sea 14Ba Seat rail bolt with washer and wing nut S/S 5x35mm S/S yes 5.50 6.05 Sea 14Bb Seat rail bolt with washer and wing nut S/S 5x45mm S/S yes 5.50 6.05 Sea 15 Seat rail wedge, painted black Wood yes 6.00 6.60
Sea16 are new parts (April 2007). Seats can now be taken off slides without removing the rail stoppers. Sea 16-800 Complete seat rail, silver anodised - 800mm Al. yes 20.00 22.00 Sea 16-850 Complete seat rail, silver anodised - 850mm Al. no 20.00 22.00 Sea 16A Seat rail stopper, new style (red) Pla yes 1.50 1.65 Sea 16B Seat rail bolt with wing nut Pla yes 4.00 4.40 Sea20 is a simple 10mm wooden spacer to fit between the seat top and seat chassis. Can be used with most makes of single action seat to lift the rower higher in the boat. Sea 20 10mm spacer for adjusting seat height, painted black Wood no 2.00 2.20 Sea21 fits between the seat top and chassis, to adjust the angle of the seat top for comfort and performance. Sea 21 2 degree wedge for adjusting seat top angle Pla no 3.00 3.30 Sea 22 Insert in seat deck for rail bolt hole Pla yes 1.50 1.65 Fins and Rudders makes 2 sizes of rudder for every racing boat. A small one (50x80mm) for straight courses, and a larger one (80x100mm) for river rowing. The shaft diameter is 7.5mm, and the length of the shaft is shown for each rudder. Shaft lengths may vary between wing rigger boats (W), and traditional rigger boats (T). It may be possible to use a rudder on other boats. If the shaft is too long, washers, or a piece of pipe can be used to make up the length. Fin 1-200S Std rudder for Freedom 2x S/S yes 90.00 99.00 Fin 1-240S Std rudder for moulds # 201(W & T), 203(W & T), 204(W & T) S/S yes 90.00 99.00 Fin 1-255S Std rudder for moulds # 202(W & T), 401(W & T) S/S yes 90.00 99.00 Fin 1-285S Std rudder for moulds # 402W, 403W, 802W S/S yes 90.00 99.00 Fin 1-305S Std rudder for moulds # 402T, 403T, 802T S/S yes 90.00 99.00 Fin 1-350S Std rudder for moulds # 801T S/S yes 90.00 99.00 Fin 1-200L Large rudder for Freedom 2x S/S yes 90.00 99.00 Fin 1-240L Large rudder for moulds # 201(W & T), 203(W & T), 204(W & T) S/S yes 90.00 99.00 Fin 1-255L Large rudder for moulds # 202(W & T), 401(W & T) S/S yes 90.00 99.00 Fin 1-285L Large rudder for moulds # 402W, 403W, 802W S/S yes 90.00 99.00 Fin 1-305L Large rudder for moulds # 402T, 403T, 802T S/S yes 90.00 99.00 Fin 1-350L Large rudder for moulds # 801T S/S yes 90.00 99.00 Fin 4-150 Rudder yoke, 150mm long, for 2s and 4s Al. yes 28.00 30.80 Fin 4-240 Rudder yoke, 240mm long, for 8s Al. yes 28.00 30.80 Fin 5 Direction pointer S/S yes 14.00 15.40
fins are the same size and shape as Empacher fins, and so are interchangeable with Empacher. Fin 10-1 Fin for 1x, replaceable type Al. yes 44.00 48.40 Fin 10-2 Fin for 2x/-/+, replaceable type Al. yes 22.00 24.20 Fin 10-4 Fin for 4x/-/+ replaceable type Al. yes 22.00 24.20 Fin 10-8 Fin for 8+, replaceable type Al. yes 22.00 24.20 Fin 10A Fin box for replaceable fin Al. yes 22.00 24.20 Fin 10B 4x15mm S/S bolt for fin box Al. yes 0.20 0.22 Fin 11-1 Fin for 1x, non-replaceable type Al. no 22.00 24.20 Fin 11-2 Fin for 2x/-/+, non-replaceable type Al. no 22.00 24.20 Fin 11-4/8 Fin for 4x/-/+, 8+, non-replaceable type Al. no 22.00 24.20 Fin 21 2mm pipe for guide holes in ribs S/S yes 3.00 3.30 Fin 22A Plastic coated rudder wire (per 1m) S/S yes 4.00 4.40 Fin 22B Plastic coated rudder wire (per 1,250m) S/S yes 3.00 3.30 Fin 23 Rudder wire guide wheel Al. yes 18.00 19.80 Fin 24 Wire fastener (2 screw type) Brass yes 2.00 2.20 Other Rowing Parts For hatches, the size refers to the hole of the hatch. Oth2-155 was only used on a few 2006 4s and 8s. Oth2-60 was only used on some 1s in 2005 and 2006. Oth 1 Bow ball Rub yes 8.50 9.35 Oth 2-60 Black hatch - 60mm (inner and outer part) Plas yes 10.00 11.00 Oth 2-100 Black hatch - 100mm (inner and outer part) Plas yes 15.00 16.50 Oth 2-133 Black hatch - 133mm (inner and outer part) Plas yes 20.00 22.00 Oth 3 Number plate holder Plas yes 5.00 5.50 We try to keep the list of colors as up to date as possible, but some colors may be out of production. Oth 4black Deck tape 25m roll - black RAL9005 Plas yes 50.00 55.00 Oth 4gmgrey Deck tape 25m roll - gunmetal grey RAL???? Plas yes 50.00 55.00 Oth 4mgrey Deck tape 25m roll - medium grey RAL7036 Plas yes 50.00 55.00 Oth 4dbrown Deck tape 25m roll - dark brown RAL8011 Plas yes 50.00 55.00 Oth 4mbrown Deck tape 25m roll - medium brown RAL8002 Plas yes 50.00 55.00 Oth 4purple Deck tape 25m roll - purple RAL4008 Plas yes 50.00 55.00 Oth 4dblue Deck tape 25m roll - dark blue RAL5010 Plas yes 50.00 55.00 Oth 4lblue Deck tape 25m roll - light (sky) blue RAL5015 Plas yes 50.00 55.00 Oth 4aqua Deck tape 25m roll - aqua RAL5012 Plas yes 50.00 55.00 Oth 4dgreen Deck tape 25m roll - hunter (dark) green RAL6012 Plas yes 50.00 55.00 Oth 4mgreen Deck tape 25m roll - kelley (medium) green RAL6001 Plas yes 50.00 55.00 Oth 4lgreen Deck tape 25m roll - light green RAL6017 Plas yes 50.00 55.00 Oth 4red Deck tape 25m roll - red RAL3001 Plas yes 50.00 55.00 Oth 4tang Deck tape 25m roll - tangerine orange RAL???? Plas yes 50.00 55.00 Oth 4yellow Deck tape 25m roll - yellow RAL1018 Plas yes 50.00 55.00 Oth 4white Deck tape 25m roll - white RAL9003 Plas yes 50.00 55.00 Oth 5 Boat names, 50mm tall, black (2 pieces) Plas no 22.00 24.20 Oth 6-200A 200g (approx.) weight/stabilizer with 10mm thread S/S no 27.50 30.25 Oth 6-200B 200g (approx.) weight/stabilizer with 12mm thread S/S no 27.50 30.25
Oth 6-400A 400g (approx.) weight/stabilizer with 10mm thread S/S no 35.00 38.50 Oth 6-400B 400g (approx.) weight/stabilizer with 12mm thread S/S no 35.00 38.50 Oth 6A-200 200g (approx.) weight with 8mm hole (no thread) S/S no 22.50 24.75 Oth 6A-400 400g (approx.) weight with 8mm hole (no thread) S/S no 27.50 30.25 Adaptive Boat Floats ADF 1 Complete float (per piece) FG yes 123.43 135.77 ADF 2 Float (without fixing arm), incl. 6mm washers and locking nuts FG yes 90.00 99.00 ADF 3 Fixing arm (for float) S/S yes 25.71 28.29 ADF 4a Rigger attachment (for Euro and ali wing, incl. 12x60mm bolt, nut, w S/S yes 12.86 14.14 ADF 4b Rigger attachment (for carbon wing, incl. 10x60mm bolt, nut, washe S/S yes 12.86 14.14 Adaptive Boat Seats ADSea 1 Complete seat (per piece - excluding straps) Al. yes 282.86 311.14 ADSea 2 Base Al. yes 90.00 99.00 ADSea 3 Back upright(pair) Al. yes 61.71 67.89 ADSea 4a Sliding adjuster for back angle (outer pipe pair) Al. yes 42.43 46.67 ADSea 4b Sliding adjuster for back angle (inner pipe pair) Al. yes 38.57 42.43 ADSea 5 Back height extender Al. yes 19.29 21.21 ADSea 6a Back cushion yes 25.71 28.29 ADSea 6b Seat cushion yes 23.14 25.46 ADSea 7a Easy release strap for lap yes 32.14 35.36 ADSea 7b Easy release strap for upper body yes 32.14 35.36 ADSea 8 "C" seat rail with 5 fixing bolts, 2 T bolts, nuts and washers (per pie Al. yes 23.14 25.46 ADSea 9 "C" seat rail only Al. yes 12.86 14.14 ADSea 10 Fixing bolt & nut for C seat rail (to seat deck of boat) S/S yes 0.51 0.57 ADSea 11 T bolt (8 x??mm), nut and washer for fixing seat to seat rail S/S yes 3.86 4.24 Gates UMKS/S Magik Sculling oarlocks set of two No 88.00 96.80 UMKR/S Magik Rowing oarlocks set of two No 88.00 96.80 UCCS/S Concept II Sculling oarlocks set of two No 58.00 63.80 UCCR/S Concept II Rowing oarlocks set oftwo No 58.00 63.80 Trestles TRE 61cm LRG Trestles (PAIR) No 135.00 148.50 TRE 86cm SML Trestles (PAIR) No 115.00 126.50
Boat Lights LTBTP/S Boat Light Port/Starboard - Bow Light B No 45.45 50.00 LTBTRU Boat Light Rudder Post - Stern Light A No 36.36 40.00 LTBTBW Boat Light (Bow) - Bow Light A No 36.36 40.00 LTBTSU Suction Light Stern - Tadpole No 36.36 40.00 WWW.SWIFTAUSTRALIA.COM