WTR SRIS QULITY Y TRITION sil mla water meter valves THNIL SHT 05/2017 IP09020 SOP SRVI ONITIONS SIL ML series are metallic ball valves manually operated that, due to their design are intended to be used in: - rinking water supplies. - Home feed applications. In general, all those applications that require a valve capable of shutting off the liquid flow, assuring leak tightness and fulfill all the following service conditions. SIL ML are quarter turn valves. Nominal pressure: Test pressure: Temperature range: Fluid: 16 bar 25 bar old water rinking water PG. 1/8
QULITY Y TRITION OMPONNTS 1 2 3 4 5 Item omponent Material Treatment 1 Handle rass W617N 2 Screw rass 3 Stem rass W617N 4 O-Ring NR 5 Lateral rass W617N 6 Seats PTF 7 Sphere rass hrome plated 8 ody rass W617N 9 Nut rass W617N 10 Washer Stainless steel ISI 304 11 Flat joint NR 11 10 9 8 7 6 Item omponent Material Treatment 15 14 1 2 3 4 5 1 Handle rass W617N 2 Screw rass 3 Stem rass W617N 4 O-ring NR 5 Flat joint NR 6 Washer Stainless steel ISI 304 7 Nut rass W617N 8 Lateral rass W617N 9 Seat PTF 10 all rass hrome plated 11 ody rass W617N 12 O-rings NR 13 Washer P rass 14 icone P25 rass 15 Nut P25 rass W617N 13 12 11 10 9 8 7 6 PG. 2/8
QULITY Y TRITION OMPONNTS Item omponent Material Treatment 1 Handle rass W617N 11 1 2 3 4 6 5 2 Screw rass 3 Stem rass W617N 4 O-rings NR 5 Flat joint NR 6 Washer Stainless steel ISI 304 7 Nut rass W617N 8 Lateral rass W617N 9 ody rass W617N 10 all rass hrome plated 11 Seat PTF 12 O-rings NR 13 Washer rass 14 icone rass 15 Nut rass W617N 12 15 14 13 9 10 8 7 PG. 3/8
QULITY Y TRITION MIN ONSTRUTIV FTURS OY N LTRL Main body and lateral made in uropean brass W617 by means of hot stamping process. oth process and the material confer the following advantages versus casting valves. - Pores and bumpy texture absence. - Surfaces with better finished. - Higher mechanical endurance against high pressures. O-rings STS Made in PTF, assuring internal and external leak tightness due to its perfect fit on metallic surfaces. INTRNL leak tightness Internal leak tightness is assured in both directions by the PTF seats that press against the spherical closure. This system can not be dismantled, avoiding improper manipulations. XTRNL leak tightness xternal leak tightness is achieved by the mean of a pair of NR O-rings. These avoid every leak and moreover are allowed to be in contact with drinking water. PTF Seat IMNSIONS SIL Straight F-LN Size 1/2 F x 3/4 LN G1/2 60 37 3/4 F x 3/4 LN 63 37 PG. 4/8
QULITY Y TRITION IMNSIONS SIL Straight M-LN Size 1/2 M x 3/4 LN G1/2 60 36 3/4 M x 3/4 LN 68 36 SIL Straight P-LN Size P 25 x 1/2 LN 25 G1/2 74 38 P 25 x 3/4 LN 25 74 38 P 32 x 3/4 LN 32 74 43 SIL Straight P25-P25 Size P 25 x P 25 25 25 74 37 PG. 5/8
QULITY Y TRITION IMNSIONS F 1/2 M x 3/4 LN G1/2 78 37 41 3/4 M x 3/4 LN 81 37 41 Size SIL ngle M-LN F Size 1/2 M x 3/4 LN G1/2 60 36 3/4 M x 1/2 LN G1/2 68 36 SIL Straight M-LN Manual ir Vent F P 25 x 3/4 LN 25 90 37 42 P 32 x 3/4 LN 32 97 37 42 Size SIL ngle P-LN F PG. 6/8
QULITY Y TRITION HYRULI FTURS SIL ML series have been tested in our laboratory to determine the hydraulic features of flow vs. loss of pressure according to uropean Norm N 1267. Loss of pressure (bar) 0,50 0,45 0,40 0,35 0,30 0,25 0,20 0,15 0,10 0,05 0,00 Flow vs. Loss of pressure 1/2 M x 3/4 LN 3/4 M x 3/4 LN 1/2 F x 3/4 LN 3/4 F x 3/4 LN 0 0,5 1,0 1,5 2,0 2,5 3,0 Flow (l/sec.) Loss of pressure (bar) 0,50 0,45 0,40 0,35 0,30 0,25 0,20 0,15 0,10 0,05 0,00 Flow vs. Loss of pressure P 25 x 1/2 LN P 25 x 3/4 LN P 32 x 3/4 LN P 25 x P 25 0 0,5 1,0 1,5 2,0 2,5 Flow (l/sec.) 3,0 PG. 7/8
QULITY Y TRITION HYRULI FTURS Loss of pressure (bar) 0,50 0,45 0,40 0,35 0,30 0,25 0,20 0,15 0,10 0,05 0,00 Flow vs. Loss of pressure 0 0,5 1,0 1,5 2,0 ngle 1/2 F x 3/4 LN ngle 3/4 F x 3/4 LN Flow (l/sec.) INSTLTION N SSMLY The installation of valves must be done with the right tool, mostly with a spanner. Hold the valve from the end of the connection, never from the central part or the neck of the valve in order to avoid internal components deformation, the valve could be damaged inevitably. The maximum lifespan of the valve is obtained with the spherical closure in full open or closed position, it is recommended to not operate in intermediate positions for long time periods. Valves should be maneuvered every 3 months. This frequency should be increased for waters with French hardness over 50º. QULITY Y TRITION v. del id, 16 46134 Foios Valencia Spain ngineering departament: Tel: +34 963 171 0 tecnica@valvulasarco.es valvulasarco.com very product has an impact on the environment during all stages of its life-cycle, including final disposal. ll components of these valves can be recycled, deposit the valve in a green or recycled point when no longer useful. Válvulas RO, SL reserves the right to change our products and specifications at any time and without prior notice. PG. 8/8