POOL FENCE EXPANSION KIT Complies with Australian Standard, AS1926.1-2012: Safety barriers for swimming pools WARNING! ADULT ASSEMBLY ONLY
PACKAGE CONTENTS: Part A - 1 x 30cm LONG POST SECTION Part B 1 x CPR CHART Part C - 1 x SECTION OF MESH FENCING FITTED WITH POLES Part D - 2 x SPRING-LOADED HOOK & EYES Part E - 4 x STEEL GROUND SPIGOTS WITH LOCKING SCREW Part F 3 x TENT PEGS Part G 2 x CABLE TIES TOOLS REQUIRED: HAMMER or MALLET 6mm ALLEN KEY
1. Layout the contents of the box to check you have all the components. 2. Select a flat, level grass area with dense soil to install the Be-Safe Pool Fence. *Please note this fence is only suitable for dense grass areas with a solid foundation. Soft clay, sand bases or any type of loose soil will not be stable enough to support the fence* 3. Layout your fence panel section (Part C) to position the ground spigots. 4. Once you are satisfied with the position of the fence section, insert the 30cm long post section (Part A) in each spigot and one at a time hammer the spigot into the ground. Note: Do not directly hammer/hit the top of the ground spigot. *Be sure to check each spigot is straight & level as it enters the ground* 5. With the ground spigots firmly in place begin inserting each fence section post into the spigots. Note: When you are first installing the fence, tension at the top of the poles is not achieved until after the sections of fence are fully attached to one another by the hook and eyes. 6. With all fence posts inserted into the ground now tighten the locking screws on each ground spigot.
7. Connect the hook & eye latches (Part D) at the top of each post where one fence section meets another. 8. Insert the tent pegs (Part F) through the eyelet in the bottom of each mesh fence panel and hammer into the ground to secure the base of the mesh. 16. Attach your CPR chart to the fence or gate with the supplied cable ties.
Congratulations your Be-Safe Pool Fence is now complete! Please read & understand the following important information: It is very important to regularly check the safe and consistent operation of your gate. Conduct repeated tests of opening the gate fully and allowing it to slam itself shut. Each time the gate shuts it should latch close. If you find the gate is not latching shut every time please check the level of the gate assembly and reposition or adjust to ensure safe and consistent operation of the gate mechanism. This fence is only suitable for dense grass areas with a solid foundation. Soft clay, sand bases or any type of loose soil will not be stable enough to support the fence. Regularly inspect the fence, mesh, posts and ground spigots for any damage or wear. Ensure all ground spigots are tight and unable to be easily removed at all times. Do not hang anything on the fence, like towels or toys. Regularly check the hinges and gate latch for safe operation. A general purpose grease should be applied to the operating parts of the gate to ensure smooth operation at all times. If you are NOT making a complete circle with your fence take into consideration that the fence must be attached to a fixed structure, then use the hook and eye to attach it and create tension. There are certain criteria you should use when deciding where to locate your fence. Make sure the fence isolates the pool area from all exits of the house. All sides of your pool area should be enclosed. Layers of protection such as a fence, pool alarm, door alarm, personal immersion alarms and constant competent adult supervision in and around your swimming pool can help reduce unauthorized access to the pool area. Your Be-Safe Pool Fence will require approval from your local council. Please contact your local council to discuss the installation and approval of your fence before attempting assembly. The Be-Safe Pool Fence complies with Australian Standard AS1926.1-2012 Safety Barriers for Swimming Pools. A copy of this test report & certificate are supplied with this manual. For a copy of the report & certificate please contact Hunter Products. Refer to Australian standard AS 2818-1993 Guide to swimming pool safety & AS 1926.2-2007 Location of safety barriers for swimming pools for further guidance on where to locate & construct your Be-Safe Pool Fence Maintenance of your Be-Safe Pool Fence : The Be-Safe Pool Fence is generally maintenance free but below are some helpful tips: If the fence gets dirty clean only with soapy water mild detergents. Do not use harsh chemicals like bleach. After a day of splashing from the pool, hose down the fence with a garden hose. Depending on the level of chlorine in the pool, pool water left on the fencing could pose deterioration issues. Store the pool fence in a dry, mould free area. Do not store with pool chemicals as the vapours or leakage may cause deterioration issues. If you have trouble inserting the posts into the ground spigot use a metal file or sand paper over the end of the post to smooth it and remove any defects that may cause it to jam on the spigot.
One-Year Limited Warranty Hunter Products warrants that your Be-Safe Pool Fence will be free from defects in materials and workmanship for a period of one year (12 months), from the date of purchase. This warranty is nontransferable. This warranty only applies where the product is completely and correctly assembled and used in accordance with all accompanying recommendations and users instructions. This warranty is in addition to your rights under the Australia Consumer Law. Hunter Products, at it s option will provide you with a refund or replacement parts for this product if it becomes defective within the warranty period. Hunter Products will bear the reasonable expense of claiming the warranty. This warranty will no longer apply where the defect is a result of an accident, misuse, abuse, neglect or other causes not arising out of defects in materials or workmanship, nor does it cover damages arising out of service by other than an authorised service person. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Please retain your receipt as proof of purchase and contact Hunter Products for further assistance. Business name: Hunter Products Pty Ltd Business address: Level 2, 424 Warrigal Road, Moorabbin, VIC, 3189, Australia Telephone number: 1800 224 094 (Monday to Friday 9am to 5pm AEST) Email address: enquiries@hunterproducts.com.au