Material Safety Data Sheet Section 1 Identification Product Name: Clearfix Spray Cleaner - CCL Manufacturer: Clearfix Aerospace, Inc. 3960 W Point Loma Blvd H369 San Diego, CA 92110 Emergency Phone Number: 619-297-3678 Recommended Use: Cleaner for Acrylic and Polycarbonate aircraft windows and for use with the Clearfix Aviation Window Restoration System Section 2 Hazard Identification 2.1 EMERGENCY OVERVIEW Odor, Color, Grade: Little or no odor, water like liquid General Physical Form: Liquid Immediate health, physical, and environmental hazards: May cause allergic skin reaction. May cause target organ effects. 2.2 POTENTIAL HEALTH EFFECTS Eye Contact: Moderate Eye Irritation: Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision. Skin Contact: Contact with the skin during product use is not expected to result in significant irritation. Allergic Skin Reaction (non-photo induced): Signs/symptoms may include redness, swelling, blistering, and itching. Dermal Effects: Signs/symptoms may include localized redness, itching, drying and cracking of skin. Inhalation: Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and throat pain. May be absorbed following inhalation and cause target organ effects. Ingestion: Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea. May be absorbed following ingestion and cause target organ effects. Target Organ Effects: Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination, nausea, slowed reaction time, slurred speech, giddiness, and unconsciousness. Contains a chemical or chemicals, which can cause birth defects or other reproductive harm. Section 3 Composition/information Ingredient C.A.S. No. % by Wt WATER SURFACTANT MELHYL P-HYDROXYNENZOATE 7732-18-5 67-63-0 Mixture 99-76-3 95-99 1-5 < 1.5 <= 0.1 Page 1 / 5
Section 4 First-aid measures The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are followed. Eye Contact: Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention. Skin Contact: Remove contaminated clothing and shoes. Immediately flush skin with large amounts of water. Get medical attention. Wash contaminated clothing and clean shoes before reuse. Inhalation: Remove person to fresh air. If signs/symptoms develop, get medical attention. If Swallowed: Do not induce vomiting unless instructed to do so by medical personnel. Give victim two glasses of water. Never give anything by mouth to an unconscious person. Get medical attention. Section 5 Fire-fighting measures Autoignition temperature Flash Point Flammable Limits(LEL) Flammable Limits(UEL) No Flash Point Material will not burn Special Fire Fighting Procedures: Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus (SCBA). Unusual Fire and Explosion Hazards: Not applicable. Section 6 Accidental Release Measures Personal precautions, protective equipment and emergency procedures Ventilate the area with fresh air. Environmental precautions Collect the resulting residue containing solution. Place in a closed container approved for transportation by appropriate authorities. Clean-up methods Contain spill. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Clean up residue with detergent and water. In the event of a release of this material, please refer to local, state and federal regulations to determine if the release qualifies as reportable. Section 7 Handling and Storage HANDLING Avoid breathing of vapors, mists or spray. Avoid eye contact with vapors, mists, or spray. STORAGE Keep from freezing. Page 2 / 5
Section 8 Exposure controls/personal protection CONTROLS Provide appropriate local exhaust ventilation on open containers. When using keep the product moist at all times. Use in an enclosed process area is recommended. Use in a well-ventilated area. Do not use in a confined area or areas with little or no air movement. EXPOSURE GUIDELINES Ingredient Authority Type Limit ACGIH ACGIH OSHA TWA STEL TWA 200 ppm 400 ppm 980 mg/m3 Additional Information SOURCE OF EXPOSURE LIMIT DATA: ACGIH: American Conference of Governmental Industrial Hygienists CMRG: Chemical Manufacturer Recommended Guideline OSHA: Occupational Safety and Health Administration AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL) PERSONAL PROTECTIVE EQUIPMENT (PPE) Eye/Face Protection Avoid eye contact with vapors, mists, or spray. Wear safety glasses Skin Protection Avoid skin contact. Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible materials. Gloves made from the following material(s) are recommended: Nitrile Rubber Respiratory Protection Avoid breathing of vapors, mists or spray. Prevention of Swallowing Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water. Page 3 / 5
Section 9 Physical and chemical properties Odor, Color, Grade: General Physical Form: Autoignition temperature Flash Point Flammable Limits(LEL) Flammable Limits(UEL) Boiling Point Vapor Density Vapor Pressure Specific Gravity ph Melting point Solubility in Water Evaporation rate Hazardous Air Pollutants Volatile Organic Compounds Kow - Oct/Water partition coef Viscosity Off-white, little or no odor Liquid No flash point 212 F 1.1 [Ref Std: AIR=1] 17.5 mmhg [@ 20 C] 1 32 F Complete 1 [Ref Std: WATER=1] 0 % weight 29 g/l 1 centipoise Section 10 Stability and reactivity Stability: Stable. Materials and Conditions to Avoid: 10.1 Conditions to avoid: None known Materials to avoid: None known Hazardous Polymerization: Hazardous polymerization will not occur. Hazardous Decomposition or By-Products Substance Condition Carbon monoxide Carbon dioxide Oxides of Sulfur Section 11 Toxicological information Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its components. Section 12 Ecological information Not determined Section 13 Disposal considerations Waste Disposal Method: Reclaim product if feasible. As a disposal alternative, dispose of waste product in a facility permitted to accept chemical waste. Page 4 / 5
Section 14 Transport information No transport restrictions Section 15 Regulatory information 311/312 Hazard Categories: Fire Hazard - No Pressure Hazard - No Reactivity Hazard - No Immediate Hazard - Yes Delayed Hazard - Yes CHEMICAL INVENTORIES Contact Clearfix Aerospace, Inc. for more information Section 16 Other Issue Date: Supercedes Date: 8/1/2014 5/7/2013 DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. Clearfix Aerospace, Inc. MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE. User is responsible for determining whether the Clearfix Aerospace, Inc. product is fit for a particular purpose and suitable for user's method of use or application. Given the variety of factors that can affect the use and application of this product, some of which are uniquely within the user's knowledge and control, it is essential that the user evaluate this product to determine whether it is fit for a particular purpose and suitable for user's method of use or application. Clearfix Aerospace, Inc. provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may have resulted in errors, omissions or alterations in this information, Clearfix Aerospace, Inc. makes no representations as to its completeness or accuracy. In addition, information obtained from a database may not be as current as the information in the MSDS available directly from Clearfix Aerospace, Inc. Page 5 / 5