Fall Propane Odorization And Odor Fade Factors

Similar documents
Knowing the Job: Any employee actively engaged in dispensing propane should meet minimum responsibilities

At this time of year,

Cylinder Exchange Training Manual

5.0 INSPECTING, FILLING AND LABELING SMALL CYLINDERS

Inert Air (N2) Systems Manual

WARNING: FOR OUTDOOR USE ONLY

SUBSTATION MAINTENANCE ELECTRICAL OPERATING PROCEDURE

HOT SHOT OPERATING INSTRUCTIONS AND OWNER S MANUAL. Model SPC-500. (Propane Torch)

SCENARIO 18 Leak on Intermodal Pressure Tank Container

Diagnosing EVAP systems By: Bernie Thompson

Veriforce TG CCT 609OP. Training Guide

CastCreations PRODUCT DESCRIPTION. Redwood Stump Fire Pit Item #: C1002. CastCreations Ph: Aurora, Utah

LP Gas Odorization and Testing

R E D I C O N T R O L S

H 2 S in the Oilfield Fact Sheet. Introduction to H 2 S. Where does H 2 S come from? Hazards of H 2 S

CNG/LPG Vehicles Emergency First Response Guide

Emergency Procedures for Forecourt Sites Storing and Dispensing LPG

LUBRICATOR ASSEMBLY AND OPERATING INSTRUCTIONS

2.2 Bobtail Delivery Operations Performance-Based Skills Assessment 2016

Focus on VOC Emissions Reduction Using an Oxygen Based Inerting Control System For Inert Gas Blanketing of Chemical Process Vessels

CITY AND COUNTY OF DENVER CR&CF RISK UNIT Compressed Gas Safety Standard

Liquid Oxygen- Helios & Helios Marathon A Guide for Patients in the Home

3/8" Dr. Air Butterfly Impact Wrench

RE: PROPANE SYSTEM & REGULATOR TESTING/INSPECTION PROCEDURE

ESCONDIDO FIRE DEPT TRAINING MANUAL Section Truck Module Page 1 of 5 Utilities Gas Emergencies Revised

OPERATING INSTRUCTIONS

TABLE OF CONTENTS Case Studies for Group Discussion... 2 End of Module Quizzes: Answer Key... 6 Pre-Certification Exam: Answer Key...

LITTLE MAX MODEL 50G 50,000 BTU PROPANE TORCH

Refrigerant R170 - ETHANE

The following instructions were provided by the manufacturer.

Emergency Water Injection /28/2017 updated 07/21/2017

3.0 Basic Plant Operations Performance-Based Skills Assessment 2016

PL-8750 Poultry House Flame Sanitizer. Assembly and Operating Instructions

AIR/OVER HYDRAULIC JACK 20 TON

MK 3 Passive Operating Guide

HEALTH AND SAFETY MANUAL

Training Program 1A Filling 1 lb. Refillable Propane Cylinders

Developing a Policy for Auto Transportation of Medical Oxygen in High Pressure Cylinders and Cryogenic Vessels

Types 749B and R130 Changeover Manifolds

PORTABLE 5 GALLON AIR TANK ASSEMBLY & OPERATING INSTRUCTIONS

School of Chemistry SOP For Operation Of Glove Boxes

MATERIAL SAFETY DATA SHEET ODORIZED PROPANE

Vortex Dual. Refrigerant Recovery Machine

XpressFill XF2500 Counter Pressure Filler. Operating Instructions

Owner's Manual and Instructions

LPG TANK INFORMATION An energy company that puts

Striking an underground pipeline or underground electric line can lead to serious injury or death. If you hit either, call (800) , even if

XpressFill XF4500C Counter Pressure Can Filler. Operating Instructions

Early evap monitors. Photo courtesy Toyota Motor Sales, U.S.A., Inc.; diagram courtesy University of Toyota

Installation and Operation Instructions

RULE 36 & H 2 S SAFETY

Winter Weather System And Health Issues

Quebec Quebec Tel : Fax : MSDS: Methane, Oxygen in Nitrogen Mixture PRODUCT INFORMATION

2008 by Controlmatik ABW

Material Safety Data Sheet

NOTES ON WATER HAMMER. 55

Material Handling and Storage of compressed gases and Air equipment

CORROSION AT THE AIR-WATER INTERFACE REMOVE THE GAS

User Information Sheet 013

Hotspotter. Model WB-100 Professional Series. Assembly, Testing & Operating Instructions. Safety Information:

Natural Gas Conversion Kit

OPERATOR S MANUAL Ar-Gone Weld Gas Analyzer

New Hampshire Public Utilities Commission CFR 49 Part 192 Regulations. MINIMUM Pipeline Safety Regulations

USER S INFORMATION MANUAL

CONTACT INFORMATION. Wayne St. Germain Transportation Specialist U.S. Department of Transportation PHMSA Inspector Training and Qualifications

Atmospheric Hazards. Hazardous Atmosphere 3/29/2017. Oxygen deficiency and enrichment Flammable gases and vapors Toxic contaminants

Safety Data Sheet Natural Gas

LIQUID OXYGEN. General. Health Effects. Safety Considerations

DUQUESNE UNIVERSITY. Liquid Nitrogen Safety

MSDS (MATERIAL SAFETY DATA SHEET) north sea BUTANE. MSDS Nr: BOC(A) Page: 1/5

MATERIAL SAFETY DATA SHEET FOR ODORIZED PROPANE

Quebec Quebec Tel : Fax : MSDS: Propane Commercial Grade PRODUCT INFORMATION

GP-1000 Berm Flamer GPK-1054 Berm Flamer Kit GP-020 Alley Flamer Attachment Assembly and Operating Instructions

XpressFill XF4500 Counter Pressure Filler. Operating Instructions

Table of Contents. I. General Instructions. II. Task Information. III. Operator Qualification Checklist. IV. Railroad Commission/Employer Record

CENTRAL PLANT HEATING/CHILLED WATER OPERATOR Ref. Code: C-WO-4

Safe Handling. of Chlor Alkali Products

Congratulations! Hand Held Torch. Warranty Policy PARTS

Compressed Gas Properties. Introduction. Compressed Gas Properties. Definition of a Compressed Gas

AIR INLINE METAL SHEAR

Owner s Manual for Assembly, Operating & Maintenance of

1 DRIVE INDUSTRIAL IMPACT WRENCH

1 Exam Prep NFPA 99 Health Care Facilities Questions and Answers (Plumbing Contractor)

ATD LB PRESSURE BLASTER INSTRUCTION MANUAL

OVERVIEW OF ODORIZATION SYSTEMS. Kyle Welker. OdorEyes Technologies, Inc West Bellfort Sugar Land, TX Introduction

Gulfstream Natural Gas System

Oxygen Dialflow Meter. Instructions for Use

OVERVIEW OF PROPANE DISTRIBUTION SYSTEMS FOR HVAC AND PLUMBING PROFESSIONALS SAMPLE COURSE

Flow meter. bellow vaporizer. APL valve. Scavenging system

OPERATING INSTRUCTIONS

Steam Locomotive Operating Procedures SVLS Locomotive 1973 Steam Up

There are three fuelling systems which use LNG/CNG and which may be found in vehicles today:

Chapter 38 Recognizing and Identifying Hazardous Materials Hazardous Materials Hazardous Materials (Haz Mat) are present in every city, county, and

Leticia Santos Hernández Pipeline Safety Specialist U.S. Department of Transportation PHMSA Inspector Training and Qualifications

TOPIC: KNOWLEDGE: K1.01 [2.5/2.7] An atmospheric pressure of 15.0 psia is equivalent to... A psig. B psig. C psig.

Oxygen Contamination

Section 2 Safety, Tools and Equipment, Shop Practices Unit 4 General Safety Practices. Unit Objectives. Pressure Vessels and Piping (1 of 2)

TECHNICAL DATA. the Viking Pilot Pressure Regulating Valve 1 Model A-1 Speed Control Assembly: OBSOLETE. the Viking Speed Control Assembly 1

CONGRATULATIONS ON YOUR PURCHASE OF YOUR THUNDER COMPRESSOR For your personal safety please read, understand and follow the information provided in

AIR COMPRESSOR OPERATING INSTRUCTION AND PARTS LIST

Transcription:

Fall 2015 Propane Odorization And Odor Fade Factors Propane is unfairly viewed by some people to be an unsafe energy source, but think about this, Can you smell an electrical short before something starts to burn? Despite this obvious weakness, most people, some of whom have a deep fear of propane, inherently view electricity as a safe way to heat and light homes. The acutely scented ethyl mercaptan adds an important safety feature to otherwise unscented propane, a chemical that is nearly undetectable without gas detecting instruments. What happens when that odor fades or is diluted? Without it, preventable accidents become far more probable. A small leak in a sealed space becomes dangerous. What factors can cause it to fade? We are going to discuss those factors in this Think Safety along with ways to prevent some of those factors from occurring. Odorization: The dosage of ethyl mercaptan must be at least 1.0 lbs/ 10,000 gallons of propane as required by NFPA 58, but typically the industry adds it at a Inside... rate of 1.5 lbs/10,000 gallons of propane. The odorant is typically injected into the odorless propane at the terminal or loading facility. The driver of the vehicle receiving the odorized propane should document any information regarding the odorization of the propane on the bill of lading and keep a copy for his files. The bill of lading for tank cars or transports should certify that odorant has been added, Continued to Next Page Odorant Recognition... Page 2 Oxidation... Page 3 New Tanks... Page 3 Removing Air And Moisture... Page 3

Think Safety! Page 2 Fall 2015 Odorization: Continued from Page One the type of odorant and the amount used. The receiving plant should review the bill of lading to confirm the certification, per- Odorant Recognition: Anyone using propane should be instructed on the smell of odorized propane. This should certainly be done at the time of first delivery and on any opportunity available thereafter. Scratch-N-Sniff pamphlets are a helpful tool in the education process as well. The odor on the pamphlet is a mixture of ethyl mercaptan and teritiary butyl mercaptan, which produces a smell very similar to odorized propane. The pamphlets can also help identify individuals with an impaired sense of smell that may have difficulty detecting the smell of odorized propane. Certain conditions can impair ones ability to detect smells. For example: sinus conditions, allergies, head colds, smoking, or recent use of alcohol or drugs all decrease the olfactory sense. Some medications can also interfere with one s ability to smell. Other people may not be able to smell propane odorants at all due to a condition called anosmia. Once those people form a sniff test and record the results. The presence of an odorant should be verified by sniff test each time the propane changes custody in the distribution network. It is also a good idea to make a written record of the positive sniff test at each point it is performed. If there is any doubt about are identified, they should be made aware of the availability of propane gas detectors. Some people who work with propane and smell it regularly can become immune to its smell and develop odor fatigue. Even someone not accustomed to smelling propane odorant over extended time periods can lose their recognition of the odor if they are subjected to it for a prolonged time period. If the smell seems to diminish, it does not mean the leak has stopped. whether there is adequate odorant present, proper testing should be conducted and odorant added or the propane replaced by properly odorized propane. Other smells may also mask propane odorant such as cooking odors, certain foods eaten, the smell of a dead animal such as a rodent, or damp smells that may be found in the basement. It also should be noted that smell of propane odorant from a leak would be most heavily concentrated near the floor as propane is heavier than air. A heavy smell of propane as the tank runs low should not be considered normal. While there might be a momentary whiff of propane odorant when the burners are lighted, the smell should not persist. The concentration of odorant in propane may be more heavily concentrated as the liquid level in the tank drops. The more heavily concentrated aroma may reveal small leaks that were not noticed when the propane entering the system was less densely odorized. A persistent rotten egg smell should signal the need for a system integrity check.

Think Safety! Page 3 Fall 2015 Oxidation: Thanks to the organosulfur compound of ethyl mercaptan we can detect propane in amounts small enough to form a precursor to any actual danger. Propane can lose its distinctive aroma when the ethyl mercaptan oxidizes. This can occur inside a storage tank due to the presence of air, water and or rust. If oxidation occurs to high enough degree it can cause extreme odor fade and make the propane s scent undetectable. Smaller cylinders have a larger ratio of interior surface to loading capacity and more susceptible to odor fade due New Tanks: to increased opportunity for absorption of the odorant by the metal surface and oxidation of the odorant by rust. It is best t o k e e p these smaller cylinders in continuous use with frequent fillings as the more they are filled the less likely they are to develop odorization problems. Odorant can stick to the surface of new tanks. If odor fade is occurring in a container, then it should be passivated to render the surface inactive. Repeated fillings of the container with propane have been shown to reduce odor fade in those containers. Passivation can be accomplished by filling a tank with Removing Air And Moisture: The United States Consumer Product Safety Commission addressed the effect of rust and the resultant condition of odor fade in propane in a 1985 study as well as in an October 1987 Memorandum. Water and air can occur in a tank when propane is introduced into new tanks that have not been properly purged or tanks that have been left open to the atmosphere. In most cases, tanks in continuous service that were properly prepared in the first place are not as susceptible to odor fade. A proper purging procedure will will reduce the effect of air and subsequently moisture on a tank. We will discuss the proper purging procedure later. Problems can also occur when older storage tanks are allowed to sit on a yard with valves or other appurtenances removed. Moisture and air is allowed to enter the tank. Rust can accumulate inside the tank. If it is restored to service without proper purging, the rust can continue to develop in the field. odorized propane and allowing it to sit for 24 hours, after which time the tank is evacuated. This process should be repeated a minimum of five times over the period of a week. This will allow the elements to react positively with the odorant. Air in cylinders and tanks can lead to moisture in the tank and in turn can lead to water vapor, then oxidation and eventually odor fade. Most of the air needs to be removed and the moisture produced by the remaining air neutralized to reduce oxidation and reduce the likelihood of odor fade occurring. Air should be purged from any new tank not pre-purged or from any used tank that has had valves opened that allowed the entrance of air. Shrink-wrapped valves in new tanks are an indication of prepurging. Avoid opening the valves of these pre-purged tanks. Open the valve on the pre-purged tank and the air will pour through to fill the vacuum and nullify the prepurge. If the new tank is not prepurged or if air has been allowed to enter the openings of an older tank, it must be purged. Never purge a tank with liquid. The liquid will flash-freeze any water vapor to the walls of the tank where it will remain Continued to Next Page

Think Safety! Fall 2015 Page 4 Removing Air And Moisture: Continued from Page Three during the purging process. Instead, use propane vapor to purge the container using the following steps: 1. Install an unloading adapter on the double check filler valve, leaving it in the closed position. 2. Install a gauge adapter assembly on the service valve POL outlet connection. Exhaust to atmosphere any air pressure in the container. 3. Attach a truck vapor equalizing hose to the vapor return valve on Articles in this publication are for information only. Nothing in this publication is to be construed as setting standards or requirements. Please consult with appropriate regulatory and rulemaking bodies for all legal requirements. the container. 4. Open the valve on the outlet end of the vapor equalizing hose, throttling it to avoid slugging the excess flow valve on the truck. Carefully observe the pressure gauge. When the gauge reading shows 15 psig, shut off the vapor valve on the hose. 5. Switch the lever on the unloading adapter to open the double check filler valve and blow down to exhaustion. 6. Close unloading adapter lever, allowing the double check filler valve to close. 7. Repeat steps (4), (5), (6), and (7) FOUR MORE TIMES. Total required time is 15 minutes or less. This purging method should only be performed in a controlled environment such as the plant. It should not be 1st Purging 2nd Purging 3rd Purging 4th Purging 5th Purging 6th Purging performed at a customer location as a considerable amount of propane will be vented to the atmosphere, 18.4 gallons for a 1,000-gallon tank and 9.2 gallons for a 500-gallon tank. Any moisture left in the tank should be neutralized by injecting methanol into the tank at a rate of one pint per 100 gallons of water capacity. %Air Remaining 50 25 12.5 6.25 3.13 1.56 % Propane Remaining 50 75 87.5 93.75 96.87 98.44 Tom Osina: Executive Director 107 S. West Street, #825 Alexandria, VA 22314 Phone: 703/530-9772 Fax: 703/530-9653 Web address: www.wvpropanegas.org Email address: wvpga@aol.com

Training Quiz Name Social Security Number 1. The dosage of ethyl mercaptan must be at least gallons of propane A. 1.0 lbs/10,000 B. 2.0 lbs/2,000 C. 1.5 lbs/1,500 D. 3.0 lbs/3,000 2. Mercaptan is typically injected into the odorless propane at the terminal or loading facility. 3. The driver of the vehicle receiving the odorized propane should document any information regarding the odorization of the propane on the bill of lading and keep a copy for his files. 4. It is a good idea to make a written record of the positive sniff test at each point it is performed. 5. Anyone using propane should be instructed on the smell of odorized propane at the time of the first delivery and on any opportunity available thereafter. 6. Which factor(s) can diminish one s ability to smell odorized propane? A. Sinus condition B. Allergies C. Head Colds D. A, B, and C 7. A heavy smell of propane as the tank runs low should be considered normal. 8. Propane can lose its distinctive aroma when the ethyl mercaptan oxidizes. 9. Which factor(s) can lead to the oxidation of ethyl mercaptan? A. Air B. Water C. Rust D. A, B, and C 10. The smaller the tank the more susceptible it is to odor fade. 11. The possibility of odor fade occurring in a new tank can be reduced by allowing the filled tank to sit for hours and repeating the process times over the period of a week. A. 5, 10 B. 24, 5 C. 24, 10 D. 1, 3 12. Air should be purged from any new tank not pre-purged or from any used tank that has had valves opened that allowed the entrance of air. 13. Each time the purging procedure is repeated, it reduces the remaining air in the tank by percent. A. 65 B. 50 C. 90 D. 30 14. It takes gallons of propane to properly purge a 500-gallon tank. A. 18.4 B. 10 C. 9.2 D. 2.9

Training Quiz Answers Name Social Security Number 1. The dosage of ethyl mercaptan must be at least gallons of propane A. 1.0 lbs/10,000 B. 2.0 lbs/2,000 C. 1.5 lbs/1,500 D. 3.0 lbs/3,000 2. Mercaptan is typically injected into the odorless propane at the terminal or loading facility. 3. The driver of the vehicle receiving the odorized propane should document any information regarding the odorization of the propane on the bill of lading and keep a copy for his files. 4. It is a good idea to make a written record of the positive sniff test at each point it is performed. 5. Anyone using propane should be instructed on the smell of odorized propane at the time of the first delivery and on any opportunity available thereafter. 6. Which factor(s) can diminish one s ability to smell odorized propane? A. Sinus condition B. Allergies C. Head Colds D. A, B, and C 7. A heavy smell of propane as the tank runs low should be considered normal. 8. Propane can lose its distinctive aroma when the ethyl mercaptan oxidizes. 9. Which factor(s) can lead to the oxidation of ethyl mercaptan? A. Air B. Water C. Rust D. A, B, and C 10. The smaller the tank the more susceptible it is to odor fade. 11. The possibility of odor fade occurring in a new tank can be reduced by allowing the filled tank to sit for hours and repeating the process times over the period of a week. A. 5, 10 B. 24, 5 C. 24, 10 D. 1, 3 12. Air should be purged from any new tank not pre-purged or from any used tank that has had valves opened that allowed the entrance of air. 13. Each time the purging procedure is repeated, it reduces the remaining air in the tank by percent. A. 65 B. 50 C. 90 D. 30 14. It takes gallons of propane to properly purge a 500-gallon tank. A. 18.4 B. 10 C. 9.2 D. 2.9