A112 STANDARDS STATUS REPORT DESIGNATION & TITLE STATUS RESPONSIBILITY A112.1.2 2012 (R2017) Air Gaps in Plumbing Systems (For Plumbing Fixtures and Water- Connected Receptors) RC #08-1056, PINS #284 LB #11-1353 (Approved) 12/28/2011 BSR-8 #1656 BSR-9 #1228 ANSI Approved S. F. Asay, Chair A112.1.2 Air Gaps LB #16-3676 (Approved) 02/02/2017 BSR-8 #2254 04/27/2017 BSR-9 #1726 A112.1.3 2000 (R2015) Air Gap Fittings for Use With Plumbing Fixtures, Appliances, and Appurtenances A112.3.1 2007 (R2017) Stainless Steel Drainage Systems for Sanitary DWV, Storm, and Vacuum Applications, Above- and Below Ground A112.3.4/CSA B45.9 2013 Macerating Toilet Systems and Related Components Published: LB #14-2738 (Approved) 12/16/2014 BSR-8 #1997 03/10/2015 BSR-9 #1513 03/13/2015 ANSI Approved LB #16-3676 (Approved) 02/02/2017 BSR-8 #2255 04/27/2017 BSR-9 #1718 /Consolidation/Redesignation 05/11/2004 RC #11-785, PINS #414 LB #13-810 /Consolidation (Disapproved) LB #13-810RC1 Recirculation (Approved) 09/23/2013 BSR-8 #1669 12/12/2013 BSR-9 #1387 12/30/2013 ANSI Approved RC #17-2511, PINS #646 LB #17-3164 Approved LB #17-3164RC1 Recirculation Approved 02/23/2018 BSR-8 #2366 05/23/2018 BSR-9 #1799 S. F. Asay, Chair A112.1.3 Air Gap Fitting/Break Devices G. W. Harrison, Chair A112.3.1 Stainless Steel Drain Systems J. Ballanco, Chair A112.3.4 Macerating Pumped Waste Systems
A112.4.1 2009 (R2014) Water Heater Relief Valve Drain Tubes LB #14-218 (Approved) 03/05/2014 BSR-8 #1917 05/21/2014 BSR-8 #1443 05/29/2014 ANSI Approved M. Weiss, Chair A112.4.1 Relief Valve Drains ASME A112.4.2/CSA B45.16 2015 Personal Hygiene Devices for Water Closets Published: September 03, 2015 A112.4.2 2009 (R2014) Water Closet Personal Hygiene Devices /Consolidation/Redesignation 12/01/2014 RC #14-2269, PINS #550 LB #14-2817 Approval (Disapproved) LB #14-2817RC1 Recirculation Approval (Approved) 03/31/2015 BSR-8 #2044 06/17/2015 BSR-9 #1549 06/19/2015 ANSI Approved 09/03/2015 Revised/Consolidated/Redesignated as ASME A112.4.2/CSA B45.16 M. Campos, Chair A112.4.2 Water Closet Personal Hygiene Devices A112.4.3 1999 (R2015) Plastic Fittings for Connecting Water Closets to the Sanitary Drainage System A112.4.4 2017 Plastic Push Fit Drain, Waste and Vent (DWV) Fittings A112.4.5 Draft Hydro-seat Lift LB #14-2738 Approved 12/16/2014 BSR-8 #1998 03/10/2015 BSR-9 #1514 03/13/2015 ANSI Approved 08/4/2016 RC #16-1833, PINS #601 LB #16-3694 New Standard Disapproved LB #16-3694RC1 New Standard Recirculation Approval (Cancelled) LB #16-3694RC101 New Std Approved 03/10/2017 BSR-8 #2271 05/24/2017 BSR-9 #1736 05/25/2017 ANSI Approved New Edition. 10/12/2017 - Published Project Dropped M. Campos, Chair A112.4.3 Plastic Fittings for Connecting Water Closets to the Sanitary Drainage System William Morris, Chair A112.4.4 Push-Fit Drain, Waste and Vent (DWV) Fittings
A112.4.6 Draft Project Dropped Mechanical Tee Tools A112.4.7-2002 (R2008) Point of Use and Branch Water Sub-metering Systems WITHDRAWN RC #09-136 LB #09-134 Approved BSR-8 #1253 BSR-9 #940 06/11/2009 ANSI Approved A112.4.8 Draft Vent Pipe Plastic Membrane Funnels ASME A112.4.14/CSA B125.14-2017 Manually Operated Valves for Use in Plumbing Systems Published: June 30, 2017 A112.4.14 2004 (R2010) Manually Operated Quarter-Turn Shutoff Valves for Use In Plumbing Systems New Harmonization 11/14/2014 RC #14-2150, PINS #547 LB #16-3071 New Std Disapproved LB #16-3071 New Std Approved 03/15/2017 BSR-8 #2275 05/31/2017 BSR-9 #1738 06/01/2017 ANSI Approved New Edition 06/01/2017 Revised/Consolidated/Redesignated as ASME A112.4.14/CSA B125.14 W. E. Chapin, Chair A112.4.8 Vent Pipe Plastic Membrane Funnels M. Campos, Chair A112.4.14 Ball Valves A112.6.1M 1997 (R2017) Supports for Off-the-Floor Plumbing Fixtures LB #16-3676 (Approved) 02/02/2017 BSR-8 #2256 04/27/2017 BSR-9 #1719 B. Tubaugh, Chair A112.6.1 Supports for Off-the- Floor Plumbing Fixtures
A112.6.2 2017 Framing-Affixed Supports for Offthe-Floor Plumbing Fixtures LB #09-1293 - Approved BSR-8 #1328 BSR-9 #992 01/04/2010 ANSI Approved 02/24/2014 PINS #524 RC #14-393, LB #14-522 Review and Comment RC #17-658 LB #17-837 Disapproved LB #17-837RC1 Approved 07/21/2017 BSR-8 #2308 10/20/2017 BSR-9 #1767 11/01/2017 ANSI Approved 12/09/2017 Published L. Himmelblau, Chair A112.6.2 Wall Affixed Support A112.6.3 2016 Floor and Trench Drains A112.6.4 2003 (R2012) Roof, Deck, and Balcony Drains 06/16/2011 RC #11-1018, PINS #420 LB #15-1084 Disapproved LB #15-1084RC1 Approved LB #15-1084RC101 Approved 11/04/2015 BSR-8 #2084 01/21/2016 BSR-9 #1582 01/26/2016 ANSI Approved RC #17-1791, PINS #638 LB #17-2822 Approved LB #17-2822RC1 Approved 11/27/2017 BSR-8 #2335 LB #12-1984 Approved 09/25/2012 BSR-8 #1734 12/12/2012 BSR-9 #1292 12/17/2012 ANSI Approved RC #13-242, PINS #483 A. Murra, Chair A112.6.3 Floor Drains M. Weiss, Chair A112.6.4 Roof Drains
and Redesignation of A112.21.3-1985 (R2007) 08/18/2011 RC #11-1413, PINS #426 A112.6.5 Draft Hydrants 01/26/2017 Project closed during the A112 Standards Committee meeting in San Juan, PR R. Burnham, Chair A112.6.5 Hydrants A112.6.6 Draft Expansion Joints SCREW THREAD GAGES A112.6.7 2010 (R2015) Sanitary Floor Sinks 01/26/2017 Project closed during the A112 Standards Committee meeting in San Juan, PR 12/10/2009 PINS #356 BSR-8 1#476 BSR-9 #1094 10/19/2010 - ANSI Approved LB #14-2738 Approved 12/16/2014 BSR-8 #1999 03/10/2015 BSR-9 #1515 03/13/2015 ANSI Approved M. Campos, Chair A112.6.6 Expansion Joints M. Weiss, Chair A112.6.7 Floor Sinks A112.6.8 Draft Trench Drains 06/16/2011 RC #11-1019, PINS #421 Brian Tubaugh, Chair A112.6.8 Trench Drains A112.6.9 2005 (R2015) Siphonic Roof Drains A112.14.1 2003 (R2017) Backwater Valves LB #14-2738 Approved 12/16/2014 BSR-8 #2000 03/10/2015 BSR-9 #1516 03/13/2015 ANSI Approved LB #16-3676 Approved 02/02/2017 BSR-8 #2257 04/27/2017 BSR-9 #1720 M. Weiss, Chair A112.6.9 Siphonic Roof Drains R. Burnham, Chair A112.14.1 Metallic and Non- Metallic Backwater Valves
A112.14.3 2018 Grease Interceptors 06/02/2015 RC #15-1263, PINS #561 LB #15-1538 Disapproved LB 15-1538RC1 Approved 07/12/2017 BSR-8 #2306 09/27/2017 BSR-9 #1765 01/10/2018 ANSI Approved 05/18/2018 Published D. Orton, Chair A112.14.3 Grease Interceptors A112.14.4 2001 (R2017) Grease Removal Devices A112.14.5 Draft Oil Separators A112.14.6 2010 (R2015) FOG (Fats, Oils & Greases) Disposal Systems LB #16-3676 Approved 02/02/2017 BSR-8 #2258 04/27/2017 BSR-9 #1721 Project Closed 08/11/2009 RC #09-1284, PINS #337 LB #09-1474RC1 Approved BSR-8 #1463 06/14/2010 ANSI Approved LB #14-2738 Approved 12/16/2014 BSR-8 #2001 03/10/2015 BSR-9 #1517 03/13/2015 ANSI Approved W. C. Whitehead, Chair A112.14.4 Grease Recovery Devices M. Weiss, Chair A112.14.6 FOG Disposal Systems
A112.18.1/CSA B125.1 2012 (R2017) Plumbing Supply Fittings Under Continuous Maintenance (No PINS Required) Published: RC #16-2298, RC #16-2299, RC #16-2300 LB #16-2965 s Approved RC #17-783 LB #17-1033 Approved 05/01/2017 BSR-8 #2286 07/18/2017 BSR-9 #1746 07/21/2017 ANSI Approved RC #17-2517 LB #17-2867 Disapproved LB #17-2867RC1 Recirculation Approved 03/05/2018 BSR-8 #2369 05/23/2018 BSR-9 #1801 M. Malatesta, Chair A112.18.1 Plumbing Fixture Fittings A112.18.2/CSA B125.2 2015 Plumbing Waste Fittings Under Continuous Maintenance (No PINS Required) Published: September 03, 2015 A112.18.3 2002 (R2017) Performance Requirements for Backflow Protection Devices and Systems in Plumbing Fixture Fittings 12/01/2014 RC #14-2270, PINS #551 LB #14-2818 Disapproved LB #14-2818RC1 Recirculation Approved 03/31/2015 BSR-8 #2043 06/17/2015 BSR-9 #1548 06/19/2015 ANSI Approved LB #16-3676 Approved 02/02/2017 BSR-8 #2259 04/27/2017 BSR-9 #1722 D. W. Viola, Chair A112.18.2 Fixture Waste Fittings Vacant, Chair A112.18.3 Backflow Devices
A112.18.6/CSA B125.6 2017 Flexible Water Connectors Under Continuous Maintenance (No PINS Required) Published: 08/11/2017 LB #14-218 Approved 03/05/2014 BSR-8 #1919 05/21/2014 BSR-8 #1445 05/29/2014 ANSI Approved RC #16-1663 LB #16-2281 Approved 03/29/2017 BSR-8 #2279 06/15/2017 BSR-9 #1740 06/19/2017 ANSI Approved S. Rawalpindiwala, Chair A112.18.6 Flexible Water Connectors A112.18.6 Flexible Water Connectors A112.18.7M-1999 (R2004) Deck Mounted Bath/Shower Transfer Valves With Internal Backflow Protection A112.18.8 2009 (R2014) In-Line Sanitary Waste Valves for Plumbing Drainage Systems A112.18.9 2011 (R2017) Protectors/Insulators for Exposed Waste and Supplies on Accessible Fixtures REVISED AND REDESIGNATED as A112.18.6/CSA B125.6-2009; Flexible Water Connectors Reaffirmed on October 5, 2004 PT and Stds Comm Ballot 11-234 Approved Public Review BSR8 1646 Closed 31 Jan 12 BSR9 1219 ANSI Approved Withdrawal 23 Feb 2012 WITHDRAWN LB #14-218 Disapproved LB #14-218RC1 Approved 03/25/2014 BSR-8 #1924 06/11/2014 BSR-9 #1452 07/10/2014 ANSI Approved LB #16-2431 Disapproved LB #16-2431RC1 Approved 10/31/2016 BSR-8 #2206 01/31/2017 BSR-9 #1677 02/24/2017 ANSI Approved G. S. Duren, Chair A112.18.8 Sanitary Waste Valves J. Ballanco, Chair A112.18.9 Barrier Free Protection for Traps and Supplies
A112.19.1/CSA B45.2 2013 Enameled Cast Iron and Enameled Steel Plumbing Fixtures Under Continuous Maintenance (No PINS Required) Published: August 08, 2013 LB #12-2881 Disapproved LB #12-2881RC1 Approved 03/26/2013 BSR-8 #1817 06/13/213 BSR-9 #1352 06/26/2013 ANSI Approved RC #17-2481 LB #17-2824 Disapproved LB #17-2824RC1 Recirculation Approved 02/23/2018 BSR-8 #2365 05/23/2018 BSR-9 #1800 S. Rawalpindiwala, Chair A112.19.1 Enameled Cast Iron Plumbing Fixtures A112.19.2/CSA B45.1 2013 Ceramic Plumbing Fixtures Under Continuous Maintenance (No PINS Required) Published: August 08, 2013 A112.19.3/CSA B45.4 2017 Stainless Steel Plumbing Fixtures Under Continuous Maintenance (No PINS Required) Published: 05/31/2017 LB #12-2882 Disapproved LB #12-2882RC1 Approved 03/26/2013 BSR8 #1818 06/13/2013 BSR-9 #1353 07/23/2013 ANSI Approved Update 01 Editorial Changes 11/05/2013 Published RC #17-2482 LB #17-2825 Disapproved LB #17-2825RC1 Recirculation Approved 03/20/2018 BSR-8 #2367 RC #16-2365 LB #16-3075 Approved 12/19/2016 BSR-8 #2235 03/001/2017 BSR-9 #1699 03/10/2017 ANSI Approved Errata #1 RC #17-1367 Issued 05/31/2017 Errata #2 RC #17-2518 Issued 05/31/2017 P. V. DeMarco, Chair A112.19.2 Vitreous China Plumbing Fixtures S. Rawalpindiwala, Chair A112.19.3 Stainless Steel Plumbing Fixtures
A112.19.4M-1994 (R2004) Porcelain Enameled Formed Steel Plumbing Fixtures CONSOLIDATED into A112.19.1/CSA B45.2-2008 also included: Supplement 1 and 2 to ASME A112.19.4M Errata issued December 96 A112.19.5/CSA B45.15 2017 Flush Valves and Spuds for Water Closets, Urinals, and Tanks Under Continuous Maintenance (No PINS Required) Published: June 02, 2017 A112.19.5-2005 Trim for Water-Closet Bowls, Tanks, and Urinals A112.19.6-1995; Hydraulic Requirements for Water Closets and Urinals Update 01 (Erratum) May 2012 Reference to CSA B125.3-2011 was missing in reference section. The year was also created in section found. LB #16-614 Approved 04/11/2016 BSR-8 #2136 07/05/2016 BSR-9 #1617 07/14/2016 ANSI Approved RC #16-1696 LB #16-2321 Disapproved LB #16-2321RC 1 Approved 02/21/2017 BSR-8 #2265 05/12/2017 BSR-8 #2265 05/23/2017 ANSI Approved Original Publication ANSI approved on November 29, 2005 REVISED AND REDESIGNATED as A112.19.5/CSA B45.15-2011; Trim for Water-Closet Bowls, Tanks, and Urinals CONSOLIDATED into A112.19.2/CSA B45.1-2008 S. Rawalpindiwala, Chair A112.19.5 A112.19.5 Project Team on Trim for Water Closet Bowls/Tanks
A112.19.7/CSA B45.10 2012 (R2017) Hydromassage Bathtub Systems Under Continuous Maintenance (No PINS Required) Published: Revsion 08/27/2010 PINS #385 LB #11-1042 Disapproved LB #11-1042RC1 Approved BSR-8 #1650 BSR-9 #1223 02/23/2012 ANSI Approved RC #16-2623 LB #16-3344 Approved 12/06/2016 BSR-8 #2228 02/17/2017 BSR-9 #1685 02/23/2017 ANSI Approved S. Rawalpindiwala, Chair A112.19.7 Whirlpool Bathtub Appliances A112.19.7-2006; Whirlpool Bathtub Appliances A112.19.8-2007; Suction Fittings for Use in Swimming Pool, Wading Pools, Spas, and Hot Tubs Original Publication ANSI approved July 24, 1995 REVISED AND REDESIGNATED as ASME A112.19.7 / CSA B45.10; Hydromassage Bathtub Systems WITHDRAWN SUPERSEDED BY APSP-16 Publish by Association of Pool & Spa Professionals Std Comm & PT Recirculation Ballot 11-464RC1 APPROVED Public Review BSR8 1557 closed 17 May 11 BSR9 1174 ANSI Approved 15 Aug 11 Addenda 'a' to ASME A112.19.8-2008 Addenda 'b' to ASME A112.19.8-2009 BSR-9 #842 08/11/2008 ANSI Approved Spa Addenda and Editorial Changes Spa Addenda Record 09-389 Stds Comm APPROVED Editorial Changes LB #09-815RC1 Stds Comm APPROVED Public Review BSR-8 #1319 BSR-9 #982 10/22/2009 ANSI Approved PUBLISHED
A112.19.9M (R2008); Non-Vitreous Ceramic Plumbing Fixtures CONSOLIDATED into A112.19.2/CSA B45.1-2008 also included: Supplement 1 to ASME A112.19.9M-1991 Erratum released for publication on 4/26/99 A112.19.10 2017 Retrofit Dual Flush Devices for Water Closets A112.19.11 Draft Penalware and Special Use Fixtures A112.19.12 2014 Wall Mounted, Pedestal Mounted, Adjustable, Elevating, Tilting, and Pivoting Lavatory, Sink, and Shampoo Bowl Carrier Systems and Drain Waste Systems A112.19.13-2001 (R2007) Electrohydraulic Water Closets Withdrawal RC #10-480 Withdrawal Disapproved 02/15/2012 RC #12.327, PINS #448 PT LB #12-569 (Disapproved) LB #13-853 (Disapproved) LB #13-853RC1 (Approved) LB #13-853RC101 Approved 03/13/2017 BSR-8 #2272 05/24/2017 BSR-9 #1737 06/19/2017 ANSI Approved 02/21/2018 Published Project Closed 05/10/2013 PINS #539; RC #14-1394 LB #14-1891 Approved LB #14-1891RC1 Approved 09/18/2014 Submitted to Publishing 09/18/2014 BSR-8 #1969 12/05/2014 BSR-9 #1486 12/09/2014 ANSI Approved 02/17/2015 Published Consolidated into A112.19.2/CSA B45.1-2008 M. Campos, Chair A112.19.10 Dual Flush Devices for Water Closets M. Campos, Chair A112.19.12 Movable Lavatory Systems
A112.19.14 2013 (R2018) Six-Liter Water Closets Equipped With a Dual Flushing Device 05/10/2013 PINS #497; RC #13-851 LB #13-1312 Approved 07/08/2013 BSR8 #1844 12/03/2013 BSR8 #1385 12/12/2013 ANSI Approved RC #18-351 LB # 18-368 Approved 02/08/2018 BSR-8 #2360 05/03/2018 BSR-9#1792 05/08/2018 ANSI Approved S. Rawalpindiwala, Chair A112.19.14 Dual Flush for 6L Water Closets A112.19.15 2012 (R2017) Bathtub/Whirlpool Bathtubs With Pressure Sealed Doors A112.19.16-2006 Terrazzo Plumbing Fixtures 04/21/2011 RC #11-1456, PINS #413 LB #11-2160 Approved BSR-8 #1640 BSR-9 #1229 03/05/2012 ANSI Approved LB #16-3676 Approved 02/02/2017 BSR-8 #2260 04/27/2017 BSR-9 #1723 WITHDRAWN 08/23/2006 ANSI Approved Stds Com Blt 09-2045 Approved Board Ballot 10-154 Approved Public Review BSR8 1455 Closed 08 Jun 10 BSR9 1065 Withdrawal ANSI Approved 07 Jul 10 Published as a harmonized Standard CSA B45.8-13/IAPMO Z403-2013 S. Rawalpindiwala, Chair A112.19.15 Bathtubs and Whirlpools with Pressure Sealed Door
A112.19.17 2010 (R2018) Manufactured Safety Vacuum Release Systems (SVRS) For Residential and Commercial Swimming Pool, Spa, Hot Tub and Wading Pool Suction Systems 04/08/2009 RC #03-1629, PINS #325 LB #08-1072RC101 Approved BSR-9 #1030 04/13/2010 ANSI Approved G. S. Duren, Chair A112.19.17 Safety Vacuum Release System (SVRS) LB #15-364 Approved 03/18/2015 BSR-8 #2039 Cancelled Extension 03/25/2015 BSR-11 #150 Extension Granted until 03/25/2018 RC #18-352 LB # 18-368 Approved 02/08/2018 BSR-8 #2361 05/03/2018 BSR-9#1793 05/08/2018 ANSI Approved A112.19.18 Glass Lavatory Fixtures A112.19.19 2016 Vitreous China Nonwater Urinals A112.20.1-2004 Qualification of Installers of High Purity Piping Systems A112.20.2-2004 Qualification of Installers of Firestops Systems and Devices for Piping Systems A112.20.3-Draft Qualification of Installers of Residential Fire Sprinkler Systems A112.21.1M-1991 Floor Drains PIR Dropped Project picked up by CSA and IAPMO CSA B45.11/IAPMO Z401-2011 01/12/2016 RC #16-68, PINS #582 LB #16-1253 Disapproved LB #16-1253RC1 Approved 06/10/2016 BSR-8 #2153 09/26/2016 BSR-9 #1628 08/31/16 ANSI Approved ANSI Approved March 18, 2004 TRANSFERRED to ASSE (July 2009 Meeting) ANSI Approved March 18, 2004 TRANSFERRED to ASSE (July 2009 Meeting) TRANSFERRED to ASSE (July 2009 Meeting) REVISED AND REDESIGNATED as A112.6.3; Floor and Trench Drains J. M. Koeller, Chair A112.19.19 Non-Water Urinals.
A112.21.2M-1983 REVISED AND REDESIGNATED as Roof Drains A112.6.4 Roof, Deck, and Balcony Drains A112.21.3M-1985 (R2017) Hydrants for Utility and Maintenance Use A112.36.2M-1991 (R2017) Cleanouts A112.26.1M Water Hammer Arresters ASSE 1002-15/ASME A112.1002-2015/CSA B125.12-15 Performance Requirements for Anti-Siphon Fill Valves (Ballcocks) for Gravity Water Closet Flush Tanks ANSI Forms Process by ASSE Published: LB #16-3676 Approved 02/02/2017 BSR-8 #2261 04/27/2017 BSR-9 #1724 LB #16-3676 Approved 02/02/2017 BSR-8 #2262 04/27/2017 BSR-9 #1725 Project Closed /Consolidation/Redesignation RC #15-913 LB #15-1082 New Std Disapproved LB #15-1082RC1 New Std Approved 10/16/2015 ANSI Approved Update #1 September 2017 D. Marbry
ASSE 1016-17/ASME A112.1016-2017/CSA B125.16-17 Performance Requirements for Automatic Compensating Valves for Individual Showers and Tub/Shower Combinations ANSI Forms Processed by ASSE Published: 02/17/2017 /Consolidation/Redesignation RC #10-920 LB #10-1040 Disapproved LB #10-1040RC101 - Approved 07/12/2012 ANSI Approved Update 01 (Erratum) May 2012 The year of a reference document in preface was corrected. Subsections of 4.5.2 were incorrectly labeled. M. Malatesta Update 02 Editorial Changes 11/05/2013 Published RC #16-924 LB #16-1371 Disapproved LB #16-1371RC1 Approved LB #16-3234 Board Approved 01/06/2017 ANSI Approved ASSE 1018/ASME A112.1018/CSA B125. Performance Requirements for Trap Seal Primer Valves Potable Water Supplied ASSE 1037-2015/ASME A112.1037-2015/ CSA B125.37-15 Performance Requirements for Pressurized Flushing Devices for Plumbing Fixtures ANSI Forms Processed by ASSE Published: February, 19, 2015 07/17/2014 During the A112 Standards Committee Meeting in Seattle, WA it was approved to remove ASME from this Tri-Harmonized project /Consolidation/Redesignation RC #13-1828 LB #13-2375 New Std Disapproved LB #13-2375RC1 New Std Approved LB #13-2375RC101 New Std Approved 10/09/2014 BSR-8 Submitted by ASSE 01/07/2015 BSR-9 Submitted by ASSE 01/21/2015 ANSI Approved Update #1 September 2017 M. Malatesta
ASSE 1070-15/ASME A112.1070-2015/CSA B125.70-15 Performance Requirements for Water Temperature Limiting Devices /Consolidation/Redesignation RC #13-2164 LB #13-2771 New Std Disapproved LB #13-2771RC1 New Std Approved LB #13-2771RC101 New Std Approved L. Himmelblau 10/30/2015 ANSI Approved ANSI Forms Processed by ASSE Published: Update #1 September 2017 Legend Blue: Red: New Standards/Draft Stage Superseded/Closed/Withdrawn Standards Revised: 05/24/2018 by A. L. Guzman Rodriguez