TX6002 Installation Instructions www.bodet-sport.com ODET SA P30001 49340 Trémentines I FRANCE Tél. 02 41 71 72 00 Fax 02 41 71 72 01 Réf : 607479 E Upon receipt, always check the product for damage during shipment. If any is found, you may file a damage claim with the carrier. 1
Table des matières I - Installation for standalone operating mode...3 Fig. 1 3 II - Installation for synchronisation with the main scoreboard...4 III - Normal operation of the 30 sec. shot clock keyboard...5 IV - Modification of the current shot clock timer value...5 V - Retrieval of the shot clock timer value...5 VI - Modification of the preset value of the RESET (default: 30 sec)...6 VII - Adjustment of the luminosity of the TX6002...6 VIII - DIP configuration for two TX6002 (max)...6 * These instructions concern only the installation of the TX6002 shot clock when it is used with the TX6220 WP (water polo) scoreboard. 2
I - Installation for standalone operating mode Installation of the horn box : TX6220 WP Shot clock keyboard RS485 Horn box Mains T+/T- (2 wires) Low voltage power supply (2 wires) Main keyboard The shotclock keyboard operates then independently. 1/ Connect each TX6002 WP to the horn box in (). 2/ Connect the shot clock keyboard to (A) of the horn box: RS485 communication. 3/ Connect the power cord to (C). A C 3
II - Installation for synchronisation with the main scoreboard Example TX6220 WP T+/T- (2 wires) Horn box Mains T+/T- (2 wires) Low voltage power supply (2 wires) RS485 Shot clock keyboard Main keyboard Installation of the horn box: 1/ Open up the horn box. 2/ Disconnect the 4 wires and remove the DIN (A) connector. Replace it by the cable gland. 3/ Feed the Data cable (2 wires) coming from the main scoreboard (D) through the gland and connect it on the terminal block (E) (white wire RT+ and brown wire RT-) of the electronic card inside the horn box. 4/ Close the horn box. 5/ Connect the shot clock keyboard do the main keyboard. 6/ Connect the power cord to (C). D A E C 4
III - Normal operation of the 30 sec. shot clock keyboard 4 5 6 7 + c - EFFACE CLEAR 3 START STOP RESET 14s RESET poss. 1 8 2 Time Pad 1/ Pressing START / STOP key (1) starts the countdown of the shot clock. Pressing again stops the countdown. When the countdown reaches 0, a sound signal is generated during 3 seconds. The LED (9) turns red when the shot clock is stopped and green when the shot clock is running. 2/ Pressing the RESET 24s (2) key for few seconds turns off the display on the TX6002 and on the keyboard. When the key is released the shot clock timer is reset to its inial value of 30 sec. 3/ Pressing the CLEAR (3) key causes the blanking of the TX6002 (the keyboard to displays - -). The timer continues to countdown. Pressing this key again causes the LCD display and the TX6002 to display the current value of the timer. 4/ Pressing the HORN (4) key turns off the horn which comes on when the shot clock reaches 0. This key does not turn on the horn. 5/ The RESET 14s (8) key is not used. IV - Modification of the current shot clock timer value 1/ Stop the shot clock by pressing the START / STOP (1). 2/ Press the C key (6). The keyboard LCD display, the keyboard LED (9) and the TX6002 blink. 3/ Pressing the + (5) key increments the shot clock timer value by 1 second. This value can be greater than the preset value of the RESET (2) (dafault value: 30 seconds). 4/ Pressing the - (7) key decrements the shot clock timer value by 1 second. 5/ Press the C (6) key to go back to normal operation. V - Retrieval of the shot clock timer value 1/ If by accident, the RESET (2) key was pressed while the shot clock was running, it is possible to retrieve the value that the timer held at the time of the accident by pressing the CLEAR (3) key within 2 seconds following the accident. 5
VI - Modification of the preset value of the RESET (default: 30 sec) 1/ Stop the shot clock by pressing the START / STOP (1). 2/ Press the C key (6) for 3 seconds. The keyboard LCD display and the TX6002 display blink. The displayed value is the current preset value of RESET. 3/ The value of the RESET is incremented by 1 sec. each time the + (5) key is pressed. The value cannot exceed 99 seconds. 4/ The value of the RESET is decremented by 1 sec. each time the - (7) key is pressed. 5/ Press the C (6) key to go back to normal operation. This parameter is not saved in case of a power failure or if the keyboard is disconnected before the end of the match. VII - Adjustment of the luminosity of the TX6002 1/ Press the + (5) key of the shot clock keyboard for 3 seconds. The LCD displays the current luminosity adjustment level (1 to 5). 2/ Press + (5) to increase the luminosity. 3/ Press - (7) to decrease it. 4/ Press C (6) to validate the luminosity level. This parameter is not saved in case of a power failure or if the keyboard is disconnected before the end of the match. VIII - DIP configuration TX6002 n 2 => The scoreboard n 1 being the main scoreboard (ex.: TX6220WP) Synchronised on on on off on off on on off off off off off off off off Standalone on on on off on on on on off off off off off off off off TX6002 n 3 Synchronised on on on off on oon on on off off off off off off off off Standalone on on on off on on on on off off off off off off off off 6
TX6002 n 4 Synchronised on on on off on on off on off off off off off off off off Standalone on on off off on on off on off off off off off off off off TX6002 n 5 Synchronised on on on off off on off on off off off off off off off off Standalone on on on off ooff on off on off off off off off off off off Dip 1 Dip 2 Dip 3 Dip 4 Dip 5 Dip 6 Dip 7 Dip 8 Dip 9 Dip 10 Dip 11 Dip 12 Dip 13 Dip 14 Dip 15 Dip 16 on on on off on on on on off off off off off off off off 7