Plumbing Products FLOOR DRAIN CLEANOUT GATE VALVE BALL VALVE.

Plumbing Products FLOOR DRAIN CLEANOUT GATE VALVE BALL VALVE www.wilsontaylor.co

INTRODUCTION Wilson Taylor Asia Pacific, headquartered in Singapore with a subsidiary based in Hong Kong and a representative office in Shanghai, is a leading provider of all aspects of corrosion control, cathodic protection systems and engineering services, and supplier of corrosion protection services relating to coatings, pipeline integrity and reinforced concrete structures. ABOUT US Wilson Taylor has achieved rapid growth since its formation in 1997 through internal expansion. Wilson Taylor offers a complete range of high quality floor drains, cleanouts and valves. Wilson Taylor plumbing products are made of selected materials and strict quality control procedures are adhered to, to ensure that right products reaches you. The products are made with high precision and can be used for commercial and residential purpose. INTRODUCTION I ABOUT US I WILSON TAYLOR

TABLE OF CONTENT FLOOR DRAIN Push fit type 4 Cover type 5 Threaded type 6 CLEANOUT Push fit type 8 Cover type 9 Threaded type 10 VALVE Gate Valves 12 Ball Valves 13 Check Valves 14 WILSON TAYLOR I TABLE OF CONTENT

FLOOR DRAINS Floor drains are designed to quickly discharge clear waste liquids into sewers; to accumulate and hold debris where necessary and direct it to proper interceptors; to provide adequate drainage regardless of traffic loads; to provide drainage in locations where aesthetic considerations must be satisfied; to provide drainage facilities in floor construction of complex design or structural limitations. The selection of proper floor drains for small buildings where floors are not subject to heavy or specialized traffic is relatively simple. There are, however, numerous types of buildings which have unusual drainage problems and require special analysis to select proper drainage equipment. Floor Drains are produced from SS304 grade material which can provide better corrosion control performances. P3 I FLOOR DRAINS I WILSON TAYLOR

PUSH FIT TYPE CONNECTION DIMENSIONS (mm) DRAWING d D1 D2 H1 H2 63 sq x 40 40 63 37 20 2.5 79 sq x 50 51 79 47 20 2.5 109 sq x 75 77 109 73 21 2.5 150 sq x 100 103 150 96 23 2.5 200 sq x 100 103 200 96 23 2.5 200 sq x 150 146 200 137 36 4 SPECIFICATIONS MATERIAL FINISH: Available in - Polished Stainless Steel - Satin Stainless Steel - Brass Plated PIPE SIZES: Available in 2, 3, 4 & 6 CODE DESCRIPTION: MODEL NOS: WT - FD - 442 - PF - SSS WT - FD - 662 - PF - SSS WT - FD - 443 - PF - SSS WT - FD - 663 - PF - SSS WT - FD - 664 - PF - SSS WT - FD - 884 - PF - SSS WT - FD - 886 - PF - SSS WILSON TAYLOR FLOOR DRAIN 6 X6 TOP SIZE FOR 4 PIPE PUSH FIT WT - FD - 664 - PF - SSS WT - FD - 442 - PF - PSS WT - FD - 662 - PF - PSS WT - FD - 443 - PF - PSS WT - FD - 663 - PF - PSS WT - FD - 664 - PF - PSS WT - FD - 884 - PF - PSS WT - FD - 886 - PF - PSS SATIN STAINLESS STEEL WT - FD - 442 - PF - BP WT - FD - 662 - PF - BP WT - FD - 443 - PF - BP WT - FD - 663 - PF - BP WT - FD - 664 - PF - BP WT - FD - 884 - PF - BP WT - FD - 886 - PF - BP HINGED TYPE CONNECTION DIMENSIONS (mm) DRAWING d D1 D2 H1 H2 H3 150 sq x 100 103 150 96 32 7 99 200 sq x 100 103 200 96 32 7 99 200 sq x 150 143 200 137 36 7 165 SPECIFICATIONS MATERIAL FINISH: Available in - Polished Stainless Steel - Satin Stainless Steel - Brass Plated PIPE SIZES: Available in 4 & 6 CODE DESCRIPTION: MODEL NOS: WT - FD - 664 - PFHG - SSS WT - FD - 884 - PFHG - SSS WT - FD - 886 - PFHG - SSS WILSON TAYLOR FLOOR DRAIN 6 X6 TOP SIZE FOR 4 PIPE PUSH FIT HINGED WT - FD - 664 - PFHG - SSS WT - FD - 664 - PFHG - PSS WT - FD - 884 - PFHG - PSS WT - FD - 886 - PFHG - PSS SATIN STAINLESS STEEL WT - FD - 664 - PFHG - BP WT - FD - 884 - PFHG - BP WT - FD - 886 - PFHG - BP WILSON TAYLOR I FLOOR DRAINS I PF I P4

COVER TYPE CONNECTION DIMENSIONS (mm) DRAWING d D1 D2 H1 H2 63 sq x 40 43.5 63 48 20 2.5 79 sq x 50 56.5 79 59 20 2.5 109 sq x 75 82.5 109 86 21 2.5 150 sq x 50 110.5 150 59 20 2.5 150 sq x 75 82.5 150 86 21 4 150 sq x 100 110.5 150 110 23 2.5 200 sq x 100 110.5 200 110 36 4 200 sq x 150 160.5 200 162 36 4 SPECIFICATIONS MATERIAL FINISH: Available in - Polished Stainless Steel - Satin Stainless Steel - Brass Plated PIPE SIZES: Available in 2, 3, 4 & 6 CODE DESCRIPTION: WILSON TAYLOR FLOOR DRAIN SATIN STAINLESS STEEL WT - FD - C664 - SSS COVER 6 X6 TOP SIZE FOR 4 PIPE MODEL NOS: WT - FD - C442 - SSS WT - FD - C662 - SSS WT - FD - C443 - SSS WT - FD - C663 - SSS WT - FD - C664 - SSS WT - FD - C884 - SSS WT - FD - C886 - SSS WT - FD - C442 - PSS WT - FD - C662 - PSS WT - FD - C443 - PSS WT - FD - C663 - PSS WT - FD - C664 - PSS WT - FD - C884 - PSS WT - FD - C886 - PSS WT - FD - C442 - BP WT - FD - C662 - BP WT - FD - C443 - BP WT - FD - C663 - BP WT - FD - C664 - BP WT - FD - C884 - BP WT - FD - C886 - BP P5 I FLOOR DRAINS I C I WILSON TAYLOR

THREADED TYPE CONNECTION DIMENSIONS (inch / mm) DRAWING d (BSPT) D1 D2 H1 H2 63 sq x 40 1-1/2 63 37 20 2.5 79 sq x 50 2 79 47 20 2.5 109 sq x 75 3 109 73 21 2.5 150 sq x 100 4 150 96 23 2.5 200 sq x 100 4 200 96 23 2.5 200 sq x 150 6 200 137 36 4 SPECIFICATIONS MATERIAL FINISH: Available in - Polished Stainless Steel - Satin Stainless Steel - Brass Plated PIPE SIZES: Available in 2, 3, 4 & 6 CODE DESCRIPTION: WILSON TAYLOR FLOOR DRAIN THREADED WT - FD - 664 - T - SSS 6 X6 TOP SIZE FOR 4 PIPE SATIN STAINLESS STEEL MODEL NOS: WT - FD - 442 - T - SSS WT - FD - 662 - T - SSS WT - FD - 443 - T - SSS WT - FD - 663 - T - SSS WT - FD - 664 - T - SSS WT - FD - 884 - T - SSS WT - FD - 886 - T - SSS WT - FD - 442 - T - PSS WT - FD - 662 - T - PSS WT - FD - 443 - T - PSS WT - FD - 663 - T - PSS WT - FD - 664 - T - PSS WT - FD - 884 - T - PSS WT - FD - 886 - T - PSS WT - FD - 442 - T - BP WT - FD - 662 - T - BP WT - FD - 443 - T - BP WT - FD - 663 - T - BP WT - FD - 664 - T - BP WT - FD - 884 - T - BP WT - FD - 886 - T - BP WILSON TAYLOR I FLOOR DRAINS I T I P6

CLEANOUTS A floor cleanout is a drain set into the floor of commercial residential buildings to allow a cleaning rod to be inserted into the drain to remove blockages. Cleanouts can be set in concrete, tile or other types of floors for this purpose. When installing a cleanout, there are a number of guidelines and tips for proper installation. Cleanouts need to be installed near sinks and other drains so they can be cleaned. Additionally, any change in pipe direction greater than 60 degrees should have a cleanout. The size of the pipe determines the size of the cleanout; however, pipes greater than 4 inches in diameter may have a cleanout that s only 4 inches in diameter. Clean outs are produced from SS304 grade material which can provide better corrosion control performances P7 I CLEANOUTS I WILSON TAYLOR

COVER TYPE CONNECTION DIMENSIONS (mm) DRAWING d D1 D2 H1 H2 63 sq x 40 43.5 63 48 20 2.5 79 sq x 50 56.5 79 59 20 2.5 109 sq x 75 82.5 109 86 21 2.5 150 sq x 50 110.5 150 59 20 2.5 150 sq x 75 82.5 150 86 21 4 150 sq x 100 110.5 150 110 23 2.5 200 sq x 100 110.5 200 110 36 4 200 sq x 150 160.5 200 162 36 4 SPECIFICATIONS MATERIAL FINISH: Available in - Polished Stainless Steel - Satin Stainless Steel - Brass Plated PIPE SIZES: Available in 2, 3, 4 & 6 CODE DESCRIPTION: WILSON TAYLOR CLEAN OUTS 6 X6 TOP SIZE FOR 4 PIPE SATIN STAINLESS STEEL WT - CO - 664 - SSS MODEL NOS: WT - CO - 442 - SSS WT - CO - 662 - SSS WT - CO - 443 - SSS WT - CO - 663 - SSS WT - CO - 664 - SSS WT - CO - 884 - SSS WT - CO - 442 - PSS WT - CO - 662 - PSS WT - CO - 443 - PSS WT - CO - 663 - PSS WT - CO - 664 - PSS WT - CO - 884 - PSS WT - CO - 442 - BP WT - CO - 662 - BP WT - CO - 443 - BP WT - CO - 663 - BP WT - CO - 664 - BP WT - CO - 884 - BP P9 I CLEANOUTS I C I WILSON TAYLOR

THREADED TYPE CONNECTION DIMENSIONS (inch / mm) DRAWING d (BSPT) D1 D2 H1 H2 63 sq x 40 1-1/2 63 37 20 2.5 79 sq x 50 2 79 47 20 2.5 109 sq x 75 3 109 73 21 2.5 150 sq x 100 4 150 96 23 2.5 200 sq x 100 4 200 96 23 2.5 200 sq x 150 6 200 137 36 4 SPECIFICATIONS MATERIAL FINISH: Available in - Polished Stainless Steel - Satin Stainless Steel - Brass Plated PIPE SIZES: Available in 2, 3, 4 & 6 CODE DESCRIPTION: WILSON TAYLOR CLEAN OUTS 6 X6 TOP SIZE FOR 4 PIPE THREADED WT - CO - 664 - T - SSS SATIN STAINLESS STEEL MODEL NOS: WT - CO - 442 - T - SSS WT - CO - 662 - T - SSS WT - CO - 443 - T - SSS WT - CO - 663 - T - SSS WT - CO - 664 - T - SSS WT - CO - 884 - T - SSS WT - CO - 442 - T - PSS WT - CO - 662 - T - PSS WT - CO - 443 - T - PSS WT - CO - 663 - T - PSS WT - CO - 664 - T - PSS WT - CO - 884 - T - PSS WT - CO - 442 - T - BP WT - CO - 662 - T - BP WT - CO - 443 - T - BP WT - CO - 663 - T - BP WT - CO - 664 - T - BP WT - CO - 884 - T - BP WILSON TAYLOR I CLEANOUTS I T I P10

VALVES A valve is a device that regulates, directs or controls the flow of a fluid by opening, closing or partially obstructing various passageways. In an open valve, fluid flows in a direction from higher pressure to lower pressure. Valves have many uses, including controlling water for Irrigation, industrial uses for controlling processes, residential uses such as on / off & pressure control to dish and clothes washers & taps in the home. The valves are also used in the military & transport sectors. Valves are found in virtually every industrial process, including water & sewage processing, mining, power generation, processing of oil, gas & petroleum, food manufacturing, chemical & plastic manufacturing and many other fields. The main parts of the most usual type of valve are the body and the bonnet. These two parts form the casing that holds the fluid going through the valve. P11 I VALVES I WILSON TAYLOR

GATE VALVES The gate valve, also known as a sluice valve, is a valve that opens by lifting a round or rectangular gate/wedge out of the path of the fluid. The distinct feature of a gate valve is the sealing surfaces between the gate and seats are planar, so gate valves are often used when a straight-line flow of fluid and minimum restriction is desired. The gate faces can form a wedge shape or they can be parallel. Gate valves are primarily used to permit or prevent the flow of liquids, but typical gate valves shouldn t be used for regulating flow, unless they are specifically designed for that purpose. Because of their ability to cut through liquids, gate valves are often used in the petroleum industry. For extremely thick fluids, a specialty valve often known as a Typical gate valves are designed to be fully opened or closed. When fully open, the typical gate valve has no obstruction in the flow path, resulting in very low friction loss. Bonnets provide leakproof closure for the valve body. Gate valves may have a screw-in, union, or bolted bonnet. Screw-in bonnet is the simplest, offering a durable, pressure-tight seal. Union bonnet is suitable for applications requiring frequent inspection and cleaning. It also gives the body added strength. Bolted bonnet is used for larger valves and higher pressure applications. Gate valves are typically constructed from cast iron, ductile iron, cast carbon steel, gun metal, stainless steel, alloy steels, and forged steels. NO. PART CODE PART NAME Q TY MATERIALS 1 S24101S304-001-3745 BODY 1 BRONZE 2 S24101S304-002-3745 WASHER 1 FIBER 3 S24101S304-003-3745 BONNET 1 BRASS 4 S24101S304-004-3745 STEM 1 BRASS 5 S24101S304-005-3745 LOCK PUT 1 BRASS 6 S24101S304-006-3745 WEDGE DISC 1 BRASS 7 S24101S304-007-3745 GLAND PACKING 1 PTFE 8 S24101S304-008-3745 GLAND 1 BRASS 9 S24101S304-009-3745 PACKING NUT 1 BRASS 10 S24101S304-010-3745 HAND WHEEL 1 PRESSED STEEL 11 S24101S304-011-3745 NAME PLATE 1 ALUMINUM 12 S24101S304-012-3745 NUT 1 STEEL PRESSURE RATING: PN 25 WORKING TEMPERATURE: Water below 120 C, Oil, Gas, Steam below 170 C THREADS: NSI B1.20.1 (NPT) AVAILABLE SIZES: ½, ¾, 1, 1 ¼, 1 ½, 2, 2 ½, 3 WILSON TAYLOR I VALVES I G I P12

BALL VALVES A ball valve is a valve with a spherical disc, the part of the valve which controls the flow through it. The sphere has a hole, or port, through the middle so that when the port is in line with both ends of the valve, flow will occur. When the valve is closed, the hole is perpendicular to the ends of the valve, and flow is blocked. The handle or lever will be inline with the port position, letting you see the valve s position. Ball valves are durable and usually work to achieve perfect shutoff. They do not offer the fine control that may be necessary in throttling applications, but are sometimes used for this purpose. The body of ball valves may be made of metal, plastic or metal with a ceramic center. The ball is often chrome plated to make it more durable. NO. PART CODE PART NAME Q TY MATERIALS 1 S18510S303-001-3745 BODY 1 BRONZE 2 S18510S303-002-3745 SEATS 2 PTFE 3 S18510S303-003-3745 BALL 1 BRASS 4 S18510S303-004-3745 CAP 1 BRONZE 5 S18510S303-005-3745 STEM 1 BRASS 6 S18510S303-006-3745 GLAND PACKING 1 PTFE 7 S18510S303-007-3745 GLAND 1 BRASS 8 S18510S303-008-3745 HANDLE 1 STEEL 9 S18510S303-009-3745 NUT 1 STEEL PRESSURE RATING: PN 25 WORKING TEMPERATURE: Water below 120 C, Oil, Gas, Steam below 170 C THREADS: ANSI B1.20.1 (NPT) AVAILABLE SIZES: ½, ¾, 1, 1 ¼, 1 ½, 2 P13 I VALVES I B I WILSON TAYLOR

CHECK VALVES A check valve, clack valve, non-return valve or one-way valve is a valve that normally allows fluid to flow through it in only one direction. Check valve is simply a freely hinged flap which drops to obstruct fluid flow in one direction, but is pushed open by flow in the opposite direction. Check valves are two-port valves, one for fluid to enter and the other for fluid to leave. There are various types of check valves used in a wide variety of applications. Check valves are often part of common household items. Although they are available in a wide range of sizes, check valves generally are very small, simple or inexpensive. Check valves work automatically and most are not controlled by a person or any external control; accordingly, most do not have any valve handle or stem. The bodies of most check valves are made of plastic or metal. NO. PART CODE PART NAME Q TY MATERIALS 1 S35000S007-001-3745 BODY 1 BRONZE 2 S35000S007-002-3745 DISC 1 BRASS 3 S35000S007-003-3745 GASKET 1 NBR 4 S35000S007-004-3745 NUT 1 BRASS 5 S35000S007-005-3745 PIN 1 BRASS 6 S35000S007-006-3745 HEXAGONAL SCREW 1 BRASS 7 S35000S007-007-3745 WASHER 1 FIBER 8 S35000S007-008-3745 CAP 1 BRASS PRESSURE RATING: PN 25 WORKING TEMPERATURE: Water below 120 C, Oil, Gas, Steam below 170 C THREADS: ANSI B1.20.1 (NPT) AVAILABLE SIZES: ½, ¾, 1, 1 ¼, 1 ½, 2 WILSON TAYLOR I VALVES I C I P14

WILSON TAYLOR ASIA PACIFIC PTE LTD NO.1, JALAN SAMULUN, SINGAPORE 629119 TEL : (65) 62640388 FAX : (65) 62641806 info@wilsontaylor.co www.wilsontaylor.co