LMP 07 Stainless Steel Sensor accuracy according to IEC 60770: standard: 0.5 % FSO option: 0.5 % / 0. % FSO Nominal pressure from 0... mho up to 0... 50 mho Output signals -wire: 4... 0 ma -wire: 0... 0 ma / 0... 0 V others on request Special characteristics diameter 6.5 mm small thermal effect excellent accuracy excellent long term stability Optional versions IS-protection zone 0 SIL (Safety Integrity Level) drinking water certificate according to DVGW and KTW different kinds of cables different kinds of seal materials The stainless steel probe LMP 07 is designed for continuous level measurement in water and clean or lightly polluted fluids. Basic element is a high quality stainless steel sensor with high requirements for exact measurement with excellent long term stability. Preferred areas of use are Water / filtrated sewage drinking water system ground water level measurement rain spillway basin pump and booster stations level measurement in container water treatment plants water recycling Fuel / Oil fuel storage tank farm BD SENSORS GmbH BD-Sensors-Straße Tel: +49 (0) 9 5 / 98-0 www.bdsensors.com D - 9599 Thierstein Fax: +49 (0) 9 5 / 98 - info@bdsensors.de
LMP 07 Technical Data Input pressure range Nominal pressure gauge [bar] 0. 0.6 0.5 0.4 0.6.6.5 4 6 0 6 5 Level [mh O].6.5 4 6 0 6 5 40 60 00 60 50 Overpressure [bar] 0.5 5 5 0 0 0 40 40 80 80 Burst pressure [bar].5.5.5 7.5 7.5 5 5 5 50 50 0 0 Output signal / Supply Standard -wire: 4... 0 ma / V S = 8... V DC SIL-version: V S = 4 8 V DC Option Ex-protection -wire: 4... 0 ma / V S = 0... 8 V DC SIL-version: V S = 4 8 V DC Options -wire -wire: 0... 0 ma / V S = 4... 0 V DC 0... 0 V / V S = 4... 0 V DC Performance Accuracy standard: nominal pressure < 0.4 bar: ± 0.5 % FSO nominal pressure 0.4 bar: ± 0.5 % FSO option : nominal pressure 0.4 bar: ± 0.5 % FSO option : for all nominal pressures: ± 0. % FSO Permissible load current -wire: R max = [(V S V S min ) / 0.0 A] current -wire: R max = 500 voltage -wire: R min = 0 k Influence effects supply: 0.05 % FSO / 0 V load: 0.05 % FSO / k Long term stability ± 0. % FSO / year at reference conditions Response time -wire: 0 msec -wire: msec accuracy according to IEC 60770 limit point adjustment (non-linearity, hysteresis, repeatability) Thermal effects (Offset and Span) Nominal pressure P N [bar] < 0.40 > 0.40 Tolerance band [% FSO] ± ± 0.75 in compensated range [ C] 0... 70 Permissible temperatures Permissible temperatures medium: -0... 70 C storage: -5... 70 C Electrical protection Short-circuit protection permanent Reverse polarity protection no damage, but also no function Electromagnetic compatibility emission and immunity according to EN 66 additional external overvoltage protection unit in terminal box KL or KL with atmospheric pressure reference available on request Electrical connection Cable with sheath material PVC (-5 70 C) grey PUR (-0 70 C) black FEP 4 (-0 70 C) black TPE-U (-0 70 C) blue (without/with drinking water certificate) cable with integrated air tube for atmospheric pressure reference 4 do not use freely suspended probes with an FEP cable if effects due to highly charging processes are expected Materials (media wetted) Housing stainless steel.4404 (6L) Seals FKM EPDM (without/with drinking water certificate) others on request Diaphragm stainless steel.445 (6L) Protection cap POM-C Explosion protection (only for 4... 0 ma / -wire) Approvals DX9-LMP 07 IBExU 0 ATEX 068 X / IECEx IBE.007X zone 0: II G Ex ia IIC T4 Ga zone 0: II D Ex ia IIIC T 85 C Da Safety technical maximum values U i = 8 V, I i = 9 ma, P i = 660 mw, C i 0 nf, L i 0 µh, the supply connections have an inner capacity of max. 7 nf to the housing Ambient temperature range in zone 0: -0... 60 C with p atm 0.8 bar up to. bar in zone or higher: -0... 70 C Connecting cables cable capacitance: signal line/shield also signal line/signal line: 60 pf/m (by factory) cable inductance: signal line/shield also signal line/signal line: µh/m Miscellaneous Option SIL version 5 according to IEC 6508 / IEC 65 Drinking water certificate 6 according to DVGW W 70 and UBA KTW (with order the indication "with drinking water certificate" is necessary) Current consumption signal output current: max. 5 ma signal output voltage: max. 7 ma Weight approx. 00 g (without cable) Ingress protection IP 68 CE-conformity EMC Directive: 04/0/EU ATEX Directive 04/4/EU 5 not in combination with the accuracy 0. %, only for 4...0 ma / -wire 6 only possible with EPDM seal in combination with TPE-U cable; not possible with IS-protection (explosion protection) pressure and level
LMP 07 Technical Data Wiring diagrams -wire-system (current) -wire-system (current / voltage) p supply + p supply + VS VS supply I supply I/U signal + A/V Pin configuration Electrical connection cable colours (IEC 60757) Dimensions (in mm) Supply + Supply Signal + (only -wire) Shield wh (white) bn (brown) gn (green) gnye (green-yellow) Total length of devices with accuracy 0. % FSO IEC 60770 increases by 5 mm! www.bdsensors.com
LMP 07 Technical Accessories Data Mounting flange with cable gland Technical data Suitable for all probes Flange material stainless steel.4404 (6L) Material of cable gland standard: brass, nickel plated on request: stainless steel.405 (0); plastic Seal insert material: TPE (ingress protection IP 68) Hole pattern according to DIN 507 Version Size (in mm) Weight DN5 / PN40 D = 5, k = 85, b = 8, n = 4, d= 4.4 kg DN50 / PN40 D = 65, k = 5, b = 0, n = 4, d= 8. kg DN80 / PN6 D = 00, k = 60, b = 0, n = 8, d= 8 4.8 kg Ordering type Ordering code DN5 / PN40 with cable gland brass, nickel plated ZMF540 DN50 / PN40 with cable gland brass, nickel plated DN80 / PN6 with cable gland brass, nickel plated Terminal clamp Technical data Suitable for all probes with cable 5.5... 0.5 mm Material standard: steel, zinc plated optionally: stainless steel.40 (04) Weight approx. 60 g Ordering type Terminal clamp, steel, zinc plated Terminal clamp, stainless steel.40 (04) Display program ZMF5040 ZMF806 Ordering code Z0058 Z0057 CIT 00 Process display with LED display CIT 50 Process display with LED display and contacts CIT 00 Process display with LED display, contacts and analogue output CIT 50 Process display with LED display, bargraph, contacts and analogue output CIT 400 Process display with LED display, contacts, analogue output and Ex-approval CIT 600 Multichannel process display with graphics-capable LC display CIT 650 Multichannel process display with graphics-capable LC display and datalogger CIT 700 Multichannel process display with graphics-capable TFT monitor, touchscreen and contacts PA 440 Field display with 4-digit LC display For further information please contact our sales department or visit our homepage: http://www.bdsensors.com cable gland M6x.5 with seal insert (for cable- 4... mm) 08 BD SENSORS GmbH The specifications given in this document represent the state of engineering at the time of publishing. We reserve the right to make modifications to the specifications and materials. pressure Tel: +49 and (0) level 9 5 / 98-0 www.bdsensors.com Fax: +49 (0) 9 5 / 98 - info@bdsensors.de LMP07_E_048
Ordering code LMP 07 LMP 07 - - - - - - - - - - Pressure in bar in mh O 4 5 0 4 5 Input [mh O] [bar].0 0.0 0 0 0.6 0.6 6 0 0.5 0.5 5 0 0 4.0 0.40 4 0 0 0 6.0 0.60 6 0 0 0 0.0 0 0 6.6 6 0 5.5 5 0 40 4.0 4 0 0 60 6.0 6 0 0 00 0 0 0 60 6 6 0 50 5 5 0 9 9 9 Housing stainless steel.4404 (6L) Diaphragm stainless steel.445 (6L) Output 4 0 ma / -wire 0 0 ma / -wire 0 0 V / -wire intrinsic safety 4 0 ma / -wire SIL 4 0 ma / -wire SIL with Intrinsic safety 4 0 ma / -wire E S ES Seals FKM EPDM DVGW/KTW: EPDM T Accuracy standard for P N 0.4 bar 0.5 % standard for P N < 0.4 bar 0.5 % 5 option for P N 0.4 bar 0.5 % option 0. % Electrical connection PVC cable PUR cable FEP cable TPE-U cable 4 DVGW/KTW:, TPE-U cable F Cable length in m standard: m PVC 0 0 standard: 5 m PVC 0 0 5 standard: 0 m PVC 0 0 standard: 5 m PVC 0 5 standard: 0 m PVC 0 0 special length PVC 9 9 9 standard: m PUR 0 0 standard: 5 m PUR 0 0 5 standard: 0 m PUR 0 0 standard: 5 m PUR 0 5 standard: 0 m PUR 0 0 special length PUR 9 9 9 standard: 5 m FEP 0 0 5 standard: 0 m FEP 0 0 special length FEP 9 9 9 special length TPE-U 9 9 9 Special version standard 0 0 0 9 9 drinking water certification only possible with EPDM seal (code T) in combination with TPE-U cable (code F); not possible with IS-protection (explosion protection) not in combination with SIL cable with integrated air tube for atmospheric pressure reference Standard lengths / 5 / 0 / 5 / 0 m are available from stock, special lengths are manufactured order-related.04.08 08 BD SENSORS GmbH The specifications given in this document represent the state of engineering at the time of publishing. We reserve the right to make modifications to the specifications and materials.