Harness Kit KIT 1 Colour: Size:
MODEL : NAVAHO BOD CROLL FAST HARNESS The results of this PPE inspection are provided to you subject to the condition that the components to be inspected do not come into any of the categories listed below, any of which would require concerning the checking of the components history, which must be done by the client. Condition of webbing (cuts, wear, burns, marks, chemical contamination, other damage) Condition of load-bearing stitching (cut, worn or pulled threads) Condition of the attachment points (deformation, marks, wear, corrosion) Condition of the adjustment buckles (deformation, marks, wear, corrosion) Condition and compatibility of the connector (see connector form) Condition of protective components (tubular protective cover of tie-in point, thigh protection) CHECK OF COMFORT COMPONENTS Condition of padding of the waistbelt and leg-loops, jacket, spreader, gear loops etc. Condition of non load-bearing stitching Check that the webbing straps are properly threaded through the buckles Verify the function of the spring in the FAST quick-connect buckle Operation of the adjustment buckles VERDICT: The product is fit to remain in service PASS (tick) VERDICT: The product is unfit to remain in service FAIL (tick) Put status of component in the column above
MODEL : CROLL ROPE CLAMP/GRAB Condition of the body (cracks, marks, wear, deformation, corrosion) Condition of the cam stop: cam groove (cracks, marks, wear, deformation, corrosion) Condition of the cam (worn or missing teeth, corrosion), rivet (cracks, marks, wear, corrosion) Condition of the safety catch (pin wear of polyamide part) Effectiveness of the return spring of the cam Effectiveness of the safety catch spring Complete opening of the safety catch on the body of the of the ascender Slides up the rope and jams when pulled down the rope
MODEL : HAND ASCENDER ROPE CLAMP/GRAB Condition of the body (cracks, marks, wear, deformation, corrosion) Condition of the cam stop: cam groove (cracks, marks, wear, deformation, corrosion) Condition of the cam (worn or missing teeth, corrosion), rivet (cracks, marks, wear, corrosion) Condition of the safety catch (pin wear of polyamide part) Effectiveness of the return spring of the cam Effectiveness of the safety catch spring Complete opening of the safety catch on the body of the of the ascender Slides up the rope and jams when pulled down the rope
MODEL : ASAP MOBILE FALL ARRESTER These PPE inspection results are valid only if neither of the following conditions are true of the equipment to be inspected: - Product has received a fall. - Component has exceeded it s lifetime The inspector declines all responsibility for inaccuracy in the information concerning the historic verification that must be done by the user. VISUAL VERIFICATION OF SAFETY ELEMENTS Condition of the body, attachment holes (cracks, marks, deformation, wear, corrosion) Condition of the articulated arm (cracks, marks, deformation, corrosion) Condition of the anti-return stop (marks, deformation) Condition of the locking wheel (worn, fouled, or missing teeth) Condition of the spring (breaks, cracks, deformation, corrosion, contamination by foreign objects) Condition of the protective cover (cracks, contamination by foreign objects) Compatibility and condition of the connector (see connector form) Check keeper cord is under 11cm (if present) FUNCTIONAL TEST Effectiveness of the articulated arm return spring (return strength and mobility) Turn the locking wheel through a complete 360 rotation in both directions The wheel should turn smoothly, without catching The ASAP should slide easily up and down the rope Fall arrest function: the fall distance of a 5 kg mass falling from the height of the carabiner must be less than 0.5 m. (Unlock the locking wheel)
MODEL : ABSORBICA ENERGY ABSORBER to be inspected do not come into any of the categories listed below, any of which would require the systematic rejection of the component, namely: concerning the checking of the component s history, which must be done by the client. Condition of the rope (cuts, wear, burns, marks, chemical contamination, soft spots) Condition of webbing (cuts, wear, burns, marks, chemical contamination) Condition of the load-bearing stitching (cut, worn, torn or pulled threads) Condition of the metal pieces (deformation, marks, cracks, wear, corrosion) CHECK OF THE COMFORT COMPONENTS Condition of the protection components (strings, stitching protectors, protective cover) COMPATIBILITY CHECK Condition and compatibility with the connector (see connector form)
MODEL : ID DESCENDER - Component had undergone modification or alteration outside the manufacturer s production units. -Component has received a fall Condition of the fixed an moving side pieces (cracks, marks, wear, deformation, corrosion) Condition of the friction component : cam groove friction pin friction runner Condition of the handle (marks deformation, cracks, wear, corrosion) Condition of the locking components (safety catch, rivets, locking pins, screws, bolts) Effectiveness of the return springs of the cam, safety catch and anti-error catch Ease of opening and closing the moving side piece Operation test on rope (braking, working position function, antipanic function) PASS FAIL
MODEL : OVAL CARABINER (Batch) CONNECTOR - Component has received a fall Condition of the body of the connector (cracks, marks, wear, deformation, corrosion) Condition of the hook or nose of the connector (cracks, marks, wear, deformation, corrosion) Condition of the gate of the connector, rivet, locking sleeve (marks, deformation, cracks, wear, corrosion) Check of the correct functioning of the gate of the connector (clean and lubricate the hinge before) Correct alignment of the gate and the hook Effectiveness of the return spring and articulation of the gate of the connector. Operation of the locking system PASS FAIL
MODEL : OK TRIACT CARABINER CONNECTOR Condition of the body of the connector (cracks, marks, wear, deformation, corrosion) Condition of the hook or nose of the connector (cracks, marks, wear, deformation, corrosion) Condition of the gate of the connector, rivet, locking sleeve (marks, deformation, cracks, wear, corrosion) Check of the correct functioning of the gate of the connector (clean and lubricate the hinge before) Correct alignment of the gate and the hook Effectiveness of the return spring and articulation of the gate of the connector. Operation of the locking system PASS FAIL
MODEL : JANE SERIAL N /TEXTILE PART: LANYARD - Component has exceeded its lifetime. Condition of the rope or webbing (cuts, wear, burns) Condition of stitching (threads cut, torn, pulled, worn) CHECK OF COMFORT COMPONENTS Condition of the comfort components (string, stitching protectors, rope protectors) COMPATIBILITY CHECK Compatibility of the lanyard with the metallic part (rope Ø - length) Condition and compatibility of the connectors (see connector form) Check of the lanyard s length adjustment system N/A N/A N/A N/A N/A N/A N/A N/A
MODEL : 4 - STEP - ETRIER SERIAL N / LANYARD - Component has exceeded its lifetime. Condition of the webbing (cuts, wear, burns, marks, chemical contamination, other damage) Condition of stitching (threads cut, torn, pulled, worn) COMPATIBILITY CHECK Condition and compatibility with the connectors