Page: 1 1. Identification GHS Product Identifier Company Name Address Telephone/Fax Number Emergency phone number Recommended use the chemical and restrictions on use 2. Hazard Identification Classification the substance or mixture Other SF01 GREASE HTL PERMA AUSTRALIA PTY LTD 10 Highbury Road Burwood Victoria 312 Australia Tel: (03) 9808 0600 Fax: 9808 0644 (03) 9808 0600 BH General purpose grease for machinery. Not classified as Hazardous according to the Globally Harmonised System Classification and labelling Chemicals (GHS) including Work, Health and Safety regulations, Australia. Not classified as Dangerous Goods according to the Australian Code for the Transport Dangerous Goods by Road and Rail. (7th edition) Contains HiTec 31. May product an allergic reaction. 3. Composition/information on ingredients on Composition Ingredients 4. First-aid measures Inhalation Ingestion Skin Eye contact First Aid Facilities Advice to Doctor Other. Fire-fighting measures Suitable extinguishing media A mixture mineral oil and additives. Name CAS Proportion Ingredients determined not to be hazardous. 100 % If inhaled, remove affected person from contaminated area. Keep at rest until recovered. If symptoms develop and/or persist seek medical attention. Do not induce vomiting. Wash out mouth thoroughly with water. Seek medical attention. Wash affected area thoroughly with soap and water. If symptoms develop seek medical attention. Medical advice must be obtained urgently if product under high pressure has been injected through the skin. Note: High Pressure Applications Injections through the skin resulting from contact with the product at high pressure constitute a major medical emergency. Injuries may not appear serious at first but within a few hours tissue becomes swollen, discoloured and extremely painful with extensive subcutaneous necrosis. Surgical exploration should be undertaken without delay. Thorough and extensive debridement the wound and underlying tissue is necessary to minimise tissue loss and prevent or limit permanent damage. Note that high pressure may force the product considerable distances along tissue planes. If in eyes, hold eyelids apart and flush the eyes continuously with running water. Remove contact lenses. Continue flushing for several minutes until all contaminants are washed out completely. If symptoms develop and/or persist seek medical attention. Eyewash and normal washroom facilities. Treat symptomatically. For advice in an emergency, contact a Poisons Centre or a doctor at once. (131 126) Use dry chemical, alcohol-resistant foam, water spray or carbon dioxide.
Page: 2 Hazards from Combustion Products Specific hazards arising from the chemical Temp. Precautions in connection with Fire Under fire conditions this product may emit toxic and/or irritating fumes, smoke and gases including carbon monoxide, carbon dioxide. Combustible. This product will burn if exposed to fire. 6. Accidental release measures Personal precautions, protective equipment and emergency procedures 7. Handling and storage Precautions for Safe Handling Conditions for safe storage, including any incompatabilities 8. Exposure controls/personal protection Occupational exposure limit values Biological Limit Values Appropriate engineering controls Respiratory Protection Fire fighters should wear Self-Contained Breathing Apparatus (SCBA) operated in positive pressure mode and full protective clothing to prevent exposure to vapours or fumes. Water spray may be used to cool down heat-exposed containers. Fight fire from safe location. This product should be prevented from entering drains and watercourses. Wear appropriate personal protective equipment and clothing to prevent exposure. Extinguish or remove all sources ignition and stop leak if safe to do so. Increase ventilation. Evacuate all unprotected personnel. If possible contain the spill. Place inert absorbent, non-combustible material onto spillage. Use clean non-sparking tools to collect the material and place into suitable labelled containers for subsequent recycling or disposal. Dispose waste according to the applicable local and national regulations. If contamination sewers or waterways occurs inform the local water and waste management authorities in accordance with local regulations. Avoid inhalation vapours and mists, and skin or eye contact. Use only in a well ventilated area. Keep containers sealed when not in use. Prevent the build up mists or vapours in the work atmosphere. Do not use near ignition sources. Do not pressurise, cut, heat or weld containers as they may contain hazardous residues. Maintain high standards personal hygiene by washing hands prior to eating, drinking, smoking or using toilet facilities. Store in a cool, dry, well-ventilated area away from sources ignition, oxidising agents, strong acids, foodstuffs, and clothing. Keep containers closed when not in use, securely sealed and protected against physical damage. Inspect regularly for deficiencies such as damage or leaks. Have appropriate fire extinguishers available in and near the storage area. Take precautions against static electricity discharges. Use proper grounding procedures. Ensure that storage conditions comply with applicable local and national regulations. No exposure standards have been established for the mixture. However, over-exposure to some chemicals may result in enhancement pre-existing adverse medical conditions and/or allergic reactions and should be kept to the least possible levels. No biological limits allocated. Provide sufficient ventilation to keep airborne levels below the exposure limits or as low as possible. Where vapours or mists are generated, particularly in enclosed areas, and natural ventilation is inadequate, a flamepro exhaust ventilation system is required. Refer to relevant regulations for further information concerning ventilation requirements. If engineering controls are not effective in controlling airborne exposure then an approved respirator with a replaceable vapor/mist filter should be used. Refer to relevant regulations for further information concerning respiratory protective requirements. Reference should be made to Australian Standards AS/NZS 171, Selection, Use and Maintenance Respiratory Protective Devices; and AS/NZS 1716, Respiratory Protective Devices, in order to make any necessary changes for individual circumstances.
Page: 3 Eye Protection Hand Protection Body Protection 9. Physical and chemical properties Appearance Colour Odour Temperature Melting Point Boiling Point Solubility in Water ph Vapour Pressure Vapour Density (Air=1) Evaporation Rate Odour Threshold Viscosity Partition Coefficient: n-octanol/water Dropping Point Density Flash Point Flammability Auto-Ignition Temperature Flammable Limits - Lower Flammable Limits - Upper Safety glasses with side shields, chemical goggles or full-face shield as appropriate should be used. Final choice appropriate eye/face protection will vary according to individual circumstances. Eye protection devices should conform to relevant regulations. Eye protection should conform with Australian/New Zealand Standard AS/NZS 1337 - Eye Protectors for Industrial Applications. Wear gloves impervious material. Final choice appropriate gloves will vary according to individual circumstances i.e. methods handling or according to risk assessments undertaken. Occupational protective gloves should conform to relevant regulations. Reference should be made to AS/NZS 2161.1: Occupational protective gloves - Selection, use and maintenance. Suitable protective workwear, e.g. cotton overalls buttoned at neck and wrist is recommended. Chemical resistant apron is recommended where large quantities are handled. Solid Brown (light) Characteristic 20 C Insoluble >7 (20 C) Base oil (Method DIN 162): 220mm2/s (40 C) 6.mm2/s (100 C) >170 C 10. Stability and reactivity Reactivity Chemical Stability Conditions to Avoid Incompatible Materials 0.8 g/cm³ (20 C) Not applicable Not flammable Product is not self-igniting. Reacts with incompatible materials Stable under normal conditions storage and handling. Heat, open flames and other sources ignition. Strong oxidizing agents.
Page: 4 Hazardous Products 11. Toxicological Toxicology Ingestion Inhalation Skin Eye Respiratory sensitisation Skin Sensitisation Germ cell mutagenicity Carcinogenicity Reproductive Toxicity STOT-single exposure STOT-repeated exposure Aspiration Hazard 12. Ecological information Ecotoxicity Persistence and degradability Mobility Bioaccumulative Potential Other Adverse Effects Environmental Protection 13. Disposal considerations Disposal Considerations 14. Transport information Transport IMDG Marine pollutant Thermal decomposition may result in the release toxic and/or irritating fumes including: hydrocarbons, carbon dioxide and carbon monoxide. No toxicity data available for this material. Ingestion this product may irritate the gastric tract causing nausea and vomiting. Inhalation product vapours may cause irritation the nose, throat and respiratory system. May be irritating to skin. The symptoms may include redness, itching and swelling. May be irritating to eyes. The symptoms may include redness, itching and tearing. Not expected to be a respiratory sensitiser. Not expected to be a skin sensitiser. Not considered to be a mutagenic hazard. Not considered to be a carcinogenic hazard. Not considered to be toxic to reproduction. Not expected to cause toxicity to a specific target organ. Not expected to cause toxicity to a specific target organ. Not expected to be an aspiration hazard. No ecological data available for this material. Prevent this material entering waterways, drains and sewers. The disposal the spilled or waste material must be done in accordance with applicable local and national regulations. Road and Rail Transport (ADG Code): Not classified as Dangerous Goods according to the Australian Code for the Transport Dangerous Goods by Road and Rail (ADG Code) (7th edition). Marine Transport (IMO/IMDG): Not classified as Dangerous Goods by the criteria the International Maritime Dangerous Goods Code (IMDG Code) for transport by sea. Air Transport (ICAO/IATA): Not classified as Dangerous Goods by the criteria the International Air Transport Association (IATA) Dangerous Goods Regulations for transport by air. No
Page: 1. Regulatory information Regulatory Poisons Schedule 16. Other Date preparation or last revision SDS Literature References Not classified as Hazardous according to the Globally Harmonised System Classification and labelling Chemicals (GHS) including Work, Health and Safety regulations, Australia. Not classified as a Scheduled Poison according to the Standard for the Uniform Scheduling Medicines and Poisons (SUSMP). Not Scheduled SDS Created: October 2014 Preparation Safety Data Sheets for Hazardous Chemicals Code Practice. Standard for the Uniform Scheduling Medicines and Poisons. Australian Code for the Transport Dangerous Goods by Road & Rail. Model Work Health and Safety Regulations, Schedule 10: Prohibited carcinogens, restricted carcinogens and restricted hazardous chemicals. Workplace exposure standards for airborne contaminants, Safe work Australia. American Conference Industrial Hygienists (ACGIH). Globally Harmonised System classification and labelling chemicals....end Of MSDS... Copyright Chemical Safety International Pty Ltd Copyright in the source code the HTML, PDF, XML, XFO and any other electronic files rendered by an Infosafe system for Infosafe MSDS displayed is the intellectual property Chemical Safety International Pty Ltd. Copyright in the layout, presentation and appearance each Infosafe MSDS displayed is the intellectual property Chemical Safety International Pty Ltd. The compilation MSDS's displayed is the intellectual property Chemical Safety International Pty Ltd. Copying any MSDS displayed is permitted for personal use only and otherwise is not permitted. In particular the MSDS's displayed cannot be copied for the purpose sale or licence or for inclusion as part a collection MSDS without the express written consent Chemical Safety International Pty Ltd.