CERTIFICATE OF APPROVAL No CF 877 This is to certify that, in accordance with TS00 General Requirements for Certification of Fire Protection Products The undermentioned products of ZOO HARDWARE LTD Unit H, Dukes Drive, Kingmoor Park North, Carlisle, Cumbria CA6 4SH Tel: 01228 672900 Fax: 01228 672928 Have been assessed against the requirements of the Technical Schedule(s) denoted below and are approved for use subject to the conditions appended hereto: CERTIFIED PRODUCT Zoo UK Size Locks and Latches TECHNICAL SCHEDULE TS23 The Contribution of Locks and Latches to the Performance of Fire Resisting of Doorsets Signed and sealed for and on behalf of CERTIFIRE Sir Ken Knight Issued: 15 February 2012 Chairman - Management Council Page 1 of 5
1. This approval applies only to the Zoo Hardware locks and latches detailed later in this certificate. 2. This certification is designed to demonstrate compliance of the product or system specifically with Approved Document B (England and Wales), Section D of the Technical Standards (Scotland) and Technical Booklet E (N. Ireland). If compliance is required to other regulatory or guidance documents there may be additional considerations or conflict to be taken into account. 3. This approval relates to their use with the following door assemblies: - Latched and unlatched, intumescent sealed door assemblies consisting of timber faced and edged leaves with timber, cellulosic or mineral cores in timber frames having a fire resistance up to 60 minutes (Code ITT). 4. The locks and latches are approved on the basis of: i) Initial type testing to EN12209 and BS EN 1634-1: 2008 ii) An appraisal against TS23 iii) Certification of quality management system to ISO 9001: 2008. iv) Inspection and surveillance of factory production control v) Ongoing audit testing in accordance with TS23 requirements 5. This approval is applicable only to the specified locks/latches used with door assemblies of proven fire resistance (as defined in BS EN 1634-1 or BS 476: Part 22: 1987) and, when fitted to timber based doorsets, using appropriate intumescent protection. The required protection will be 1 mm thick Mono Ammonium Phosphate intumescent sheet material around the lock case and a bedding of the same type of material behind the forend and strike plate. A 1 mm thickness shall be provided behind the forend and strike plate of the lockset when fitted to 30 minute doorsets with a 2 mm thickness at these positions when fitted to 60 minute doorsets. Failure to install the protection will invalidate this certificate. 6. Lock assemblies not incorporating a latching mechanism shall only be fitted to proven unlatched doorset assemblies. 7. The approval relates to on going production. Product and/or its immediate packaging are identified with the manufacturer s name, the product name or number, the CERTIFIRE name or name and mark, together with the CERTIFIRE certificate number and application where appropriate. Page 2 of 5 Signed Issued: 15 February 2012
8. The locks/latches should not be fitted higher than 1100 mm from the finished floor level of the surrounding floors. 9. The doorset shall be installed in accordance with BS 8214: 2008. 10. The following table shows acceptable doorset types and fire resistance periods: Approved Door Type Class IMM MM TT ITT ITM ITC TM FD20 FD30 FD60 FD120 FD240 E 20 EI 20 E 30 EI 30 E 60 EI 60 E 90 EI 90 E 120 EI 120 E 240 EI 240 See CERTIFIRE Technical Schedules for designation of doorset types i.e. ITT etc. Page 3 of 5 Signed Issued: 15 February 2012
Approved lock/latch models and classifications. Lock/Latch Reference Description Classification to EN 12209: 2003 ZUKS564 ZUKS576 5 Lever Sash Lock - 5 Lever Sash Lock - 2 H 8 1 0 G 2 B D 2 B ZUKS364 ZUKS376 3 Lever Sash Lock - 3 Lever Sash Lock - 2 H 8 1 0 G 2 B D 2 A ZUKD564 ZUKD576 5 Lever Dead Lock - 5 Lever Dead Lock - 2 H 8 1 0 G 2 B D 0 B ZUKD364 ZUKD376 3 Lever Dead Lock - 3 Lever Dead Lock - 2 H 8 1 0 G 2 B D 0 A ZUKF64 ZUKF76 ZUKF102 ZUKU64 ZUKU76 ZUKS64EP ZUKS76EP ZUKS64OP ZUKS76OP Flat Latch - Flat Latch - Flat Latch - 102mm Upright Latch - Upright Latch - Euro Profile Sash Lock - Euro Profile Sash Lock - Oval Profile Sash Lock - Oval Profile Sash Lock - 2 H 8 1 0 G - B 0 2 0 2 H 8 1 0 G 2 B A 2 0 Page 4 of 5 Signed Issued: 15 February 2012
Approved lock/latch models and classifications (continued). Lock/Latch Reference ZUKD64EP ZUKD76EP ZUKD64OP ZUKD76OP ZUKUD64EP ZUKUD76EP ZUKUD64OP ZUKUD76OP Description Classification to EN 12209: 2003 Euro Profile Dead Lock - Euro Profile Dead Lock - Oval Profile Dead Lock - Oval Profile Dead Lock - Upright Euro Dead Lock - Upright Euro Dead Lock - Upright Oval Dead Lock - Upright Oval Dead Lock - 2 H 8 1 0 G 2 B A 0 0 ZUKB64 ZUKB76 Bathroom Lock - Bathroom Lock - 2 H 8 1 0 G - B G 2 0 The locks/latches are available with square or radius forends and are approved in various finishes: SS, PS and PVD. Further Information Further information regarding the details contained in this certificate may be obtained from Zoo Hardware Ltd (Tel: 01228 672900). Further information regarding CERTIFIRE certification and other approved products can be obtained from CERTIFIRE (Tel: 01925 646777). Page 5 of 5 Signed Issued: 15 February 2012