THE PERFECT PRESSURE DROP TRAP PRIMER FIGURE NO. 2694 PATENT NO. 9,708,808 Regularly furnished in Lead-Free Brass as shown (back). Optional finishes available in Chrome (front), Nickel, or Stainless Steel plating.
FIGURE NO. 2694 WHAT IS THE TRAP-DEFENDER? NPT PLUG COMPRESSION FITTINGS DISTRIBUTION UNIT TRAP-DEFENDER IS A PRESSURE DROP TRAP PRIMER DESIGNED TO BE CONNECTED TO ANY POTABLE COLD WATER LINE. IT IS AUTOMATICALLY ACTIVATED WHEN AN ONLINE VALVE OR FAUCET IS OPENED AND THE SYSTEM EXPERIENCES A DROP IN PRESSURE. A PRESSURE DROP OF 3 PSI OR GREATER WILL ACTIVATE THE TRAP-DEFENDER VALVE AND RELEASE WATER INTO THE TRAP. DISTRIBUTION UNIT THE TRAP PRIMING DISTRIBUTION UNIT SIMPLY AND EFFECTIVELY PRIMES UP TO FOUR FLOOR DRAINS AND USES ONLY ONE TRAP PRIMING VALVE. SMITH FIGURE NUMBER - ALL REGULARLY FURNISHED WITH FOUR OUTLETS ½ NPTM INLET 294DA 294DA-500 294DA-625 BODY WITH TWO (2) POLYETHYLENE PLUGS AND TWO (2) 3/8 NPTF PLUGS BODY WITH FOUR (4) 1/2 O.D. COMPRESSION FITTINGS OUTLETS ABS BODY WITH FOUR (4) 5/8 O.D. COMPRESSION FITTINGS OUTLETS
THE TRAP-DEFENDER A DECREASE IN WATER LINE PRESSURE WILL ACTIVATE THE VALVE AND RELEASE WATER TO THE TRAP. FILTER SCREEN Inside Inlet THREAD SIZE ½ NPTM APPLICATION: The Trap-Defender is ideal for use in commercial buildings. TRAP PRIMER VALVE LEAD FREE NSF/ANSI 372 IAPMO & ASSE LISTED 3437 1018 OPTIONAL MANUAL PRIMING LEVER AIR GAP VACUUM RELIEF FIP THREAD SIZE ½ NPTF FIGURE NO. 2694 PATENT NO. 9,708,808 LEAD FREE. STANDARD FINISH IN BRASS, AS SHOWN. OPTIONAL FINISHES AVAILABLE IN CHROME, NICKEL OR STAINLESS STEEL PLATING.
HOW IT WORKS When static water pressure is applied, water pushes the inlet check valve open, flows into the lower compression chamber and compresses the gas bubbles inside the foam ring. These gas bubbles push back against the inlet pressure with equal and conforming force. 01 Initial inward flow when the water supply is opened. 01 02 The Anti-Oscillation Valve's center orifice reduces inlet flow and delays the recompression of the foam ring for a fraction of a second, thus preventing trap primer oscillation due to water hammer effect. This valve allows ultralow pressure drop sensitivity in the trap primer valve design. 02 03 03 04 05 Line pressure is holding the outlet valve seat closed. The inlet check valve is open, allowing water to enter the lower chamber and compressing the foam ring s internal gas bubbles. The foam ring, being compressed by the inlet pressure, stores and equals this pressure information with no measurable difference between line pressure and the pressure of the foam ring, other than differential pressure. The capability of the foam to equal the line pressure allows constant and automatic adjustment to changes in static line pressure. No manual adjustment is required. 04 05 FIGURE NO. 2694
COMPONENTS 01 03 02 04 01 RETAINER RING 05 02 03 FILTER SCREEN INSIDE INLET ANTI-OSCILLATION VALVE 06 04 THREAD SIZE ½ NPTM 07 05 TP UPPER BODY 06 07 DIAPHRAGM (RUBBER) COMPRESSION ELEMENT (FOAM RING) 08 08 09 TRAP PRIMER VALVE O-RING 09 10 TP LOWER BODY 10 11 12 13 THREAD SIZE ½ NPTF OPTIONAL MANUAL PRIMING LEVER PRIMING PIN 12 11 13
FIGURE NUMBER 2694 PRIME MULTIPLE TRAPS THE TRAP-DEFENDER: Can prime up to four traps with the use of a single distribution unit (Fig. No. 294DA) Should be located within 20 of the floor drain trap. Should be installed a minimum of 12 above the finished floor. REGULARLY FURNISHED: Lead Free Brass with 1/2 NPT Connections as illustrated. VARIATIONS: Fig. 2694-UN 1/2 NPT Union Fig. 2694-SW 1/2 Sweat Union Manual Priming Valve MPV Distribution Unit Fig. 294DA ACORN ENGINEERING COMPANY 1709HEU ADA STAINLESS STEEL HIGH EFFICIENCY URINAL OPTIONAL MATERIALS: Chrome Plated -CP Nickel Plated -NP Stainless Steel -SS JAY R. SMITH MFG. CO. 2005 GENERAL PURPOSE FLOOR DRAIN WITH ADJUSTABLE STRAINER HEAD
FEATURES AND BENEFITS: NEO-METRO 9121 WALL MOUNTED PAT BASIN n Fully automatic, no adjustments needed n Operates at pressures from 20-80 PSI, with a minimum pressure drop of 3 PSI n The Trap-Defender does not require flow through the device in order to activate and can be mounted at the end of a water supply line branch pipe n The Trap-Defender will produce output after an increase in supply line pressure due to water hammer effect JAY R. SMITH MFG. CO. 2694 TRAP-DEFENDER WITH DISTRIBUTION UNIT JAY R. SMITH MFG. CO. 4760 DRYWALL ACCESS DOOR n With virtually no moving parts within the Trap-Defender, the friction associated with pistons or o-rings has been eliminated, thus greatly increasing the 2694 senstivity, allowing increased reaction to low flow type valves n For periods of low water usage due to holidays or down periods, the Trap-Defender is equipped with an optional manual trap primimg lever that allows maintenance to fill empty/low traps and clean/test the trap primer n ASSE tested to 5000+ cycles n Three year warranty n Lead-free n Patent No. 9,708,808 c 3437 1018
The Trap-Defender comes boxed with 30 individually packaged units and provides a convenient way for wholesalers to purchase and stock the Trap-Defender product. EACH PACKAGE INDIVIDUALLY LABELED WITH MODEL AND MATERIAL RELATED PRODUCTS See the other trap primers in Smith s product line and complement your trap primer installation with our accessory options. 2698 PRIME EZE WATER SAVER FIGURE NUMBER 2699 LEAD-FREE AUTOMATIC TRAP PRIMER FIGURE NUMBER 2699-1 LEAD-FREE AUTOMATIC TRAP PRIMER WITH COPPER SWEAT FIGURE NUMBER 2696 AUXILIARY INLET FITTING WITH THREADED OUTLET FIGURE NUMBER 2697 AUXILIARY INLET FITTING WITH CAULK OUTLET FIGURE NUMBER 2695 CAST IRON AUXILIARY INLET FITTING 5000 SERIES HYDROTROL WATER HAMMER ARRESTER 5200 SERIES PISTON TYPE WATER HAMMER ARRESTER FIGURE NUMBER 2692 QUAD CLOSE STINK STOPPER TRAP SEAL DEVICE 2781 Gunter Park Dr. East, Montgomery, AL 36109 334-277-8520 JRSMITH.COM SPM0838 03/18