INSTALLATION INSTRUCTIONS JUL. 2006 Parts List Bicycle attachment Key plates (2) Tools Required Phillips screwdriver Flat-tip screwdriver Before You Begin Customer Information This Bicycle Attachment is designed to be used exclusively with the Honda Access Roof Carrier which is sold separately. Have the recommended Roof Carrier on hand before using this bicycle attachment. Do not install this Bicycle Attachment on other than the Honda Access Roof Carrier. Be extremely careful not to damage the roof and other finished surfaces of the body. Installation 1. Remove the cover from end of the front roof carrier by inserting the Key plate and turning it counterclockwise. ROOF CARRIER COVER KEY PLATE 2826061W Honda Access Corp. 2006 1 / 13
2. Pull the rubber from the carrier bar of the roof carrier and remove it. RUBBER CARRIER BAR ROOF CARRIER RUBBER 2023090W 3. Insert the key plate into the lever of the frame holder, and turn it clockwise to unlock, then raise the lever. FRAME KEY Unlock 2024260M 2 / 13
4. Rotate the frame holder so that it points towards the outside of the bicycle attachment, and then rotate the pipe to the front. PIPE FRAME 2025090M 5. Raise the three levers of the bicycle attachment and slide square-headed bolts into the carrier bar and install them. CARRIER BAR SQUARE-HEADED BOLT 2025100M 3 / 13
6. Raise the lever vertically, turn it to the clockwise to tighten it, and then return it to its original position. 2025110M 7. Install and lock the cover by inserting the Key plate and turning it clockwise. Repeat on the rear side. COVER KEY PLATE 2826091W 8. Place the bicycle onto the bicycle attachment. Placing the bicycle is made easier when the front and the rear strap of the bicycle attachment are shifted to one side as shown. STRAP Shift to one side. 2025121M 4 / 13
9. Raise the pipe so that the frame holder comes to the position of the bicycle frame. 10. Adjust the position of the frame holder and clamp the frame of the bicycle with the frame holder. The frame holder can clamp frames from a minimum diameter of 20 mm to a maximum diameter of 80 mm. When transporting a bicycle which cannot be fixed with the bicycle attachment, the bicycle may drop down and cause a large accident. FRAME FRAME Min. 20 mm, max. 80 mm FRAME FRAME 2025131M 11. Raise the lever of the frame holder and turn it to the clockwise to tighten. Fold the lever down and insert the key plate and turn counterclockwise to lock. FRAME KEY Lock 2025141M 5 / 13
12. Slide the wheel holder at the rear of the bicycle attachment in longitudinal direction to adjust the position and pass the strap through the rear wheel of the bicycle to fix it. 13. Pass the strap of the wheel holder at the front of the bicycle attachment through the front wheel of the bicycle and the hole of the bicycle attachment and fix it. Insert the excess length of the straps from underneath into the wheel holders and fix them, so that they will not hang down and hit the roof. WHEEL STRAP STRAP Insert the excess length. 2025150M 14. Check after installation: Rock the bicycle attachment in all directions to check if it is installed securely without play or rattle. If found with abnormal play or rattle, retighten the bolts, or reinstall the bicycle attachment as described in these installation instructions. Rock the bicycle attachment in all directions to check if it is installed securely without play or rattle. 2025160M 6 / 13
When the bicycle attachment is to be installed on the right side of the car, perform the following steps 15 to 31 and change the pipe and other parts to the opposite side. 15. Raise the lever on the opposite side and raise the pipe to a vertical position. PIPE 2025180M 16. Remove the socket from the bicycle attachment. SOCKET 2025190M 7 / 13
17. Match the mark on the wedge to the mark on the bicycle attachment. Pull up the wedge while pushing it from below and remove it. Match the marks. WEDGE WEDGE Push. 2028060M 18. Pull out the pipe and insert it from the opposite side. PIPE 2028111M 8 / 13
19. Install the wedge on the opposite side after matching the mark to the mark on the bicycle attachment. 20. Install the socket on the opposite side. WEDGE WEDGE Match the marks. SOCKET 2028120M 21. Turn the lever of the frame holder to the left and remove it by pulling it out. 22. Remove the washer. 23. Remove the two screws and remove the clamp part of the frame holder. CLAMP PART OF THE FRAME WASHER SCREW 2029050M 24. Set the clamp part to the opposite side and install it with the two screws, the washer, and the lever. WASHER CLAMP PART OF THE FRAME SCREW 2029060M 9 / 13
25. Turn the bicycle attachment upside down, remove the screw, and remove the front wheel holder. SCREW FRONT WHEEL Turn upside down. 2028130M 26. Turn the front wheel holder for 180 and install it with the screw. SCREW FRONT WHEEL 2028140M 27. Slide the rear load bar attachment to the front and remove it. REAR LOAD BAR 2029030M 10 / 13
28. Turn the rear load bar attachment for 180, slide it in from the front of the bicycle attachment, and install it. REAR LOAD BAR 2029040M 29. Slide the rear wheel holder to the rear and install it. REAR WHEEL REAR WHEEL 2029010M 30. Turn the rear wheel holder for 180, slide it from the rear to the opposite side, and install it. 31. Confirm that all reinstalled parts are installed securely. REAR WHEEL REAR WHEEL 2029020M 11 / 13
32. Write down the key number in case the key is lost or stolen. KEY PLATE 2827010W When no bicycle is loaded, fold the pipe down to the back and fix it by inserting the projection of the bicycle attachment into the hole of the frame holder. PIPE FRAME PROJECTION 2025170M 12 / 13
Use and Care After installation, inspect all bolts, knobs, and belts for looseness and retighten as required. When transporting a bicycle which cannot be fixed with the bicycle attachment, the bicycle may drop down and cause a large accident. This product is intended to fix a bicycle to the separately sold roof carrier. Do not use it for a different purpose. Do not load bicycles with a frame (the part clamped by the frame holder) which is not round or which has a diameter over 80 mm. When the tire air pressure of the bicycle is low, slack can develop while driving, and it is to be feared that the bicycle may drop off. Fix the bicycle with the correct tire air pressure. The maximum allowable load limit (the weight of the bicycle) of this bike attachment is 15 kg. Precautions Before and after a drive, as well as when loading a bicycle, check all parts for play, looseness, and movement, and retighten as required. When driving with a bicycle on the car, the overall height is increased, and sufficient care is required for parking lots, underpasses, and other places with height restrictions. When driving with a bicycle on the car, avoid sudden acceleration, sudden deceleration, and severe turns, pay sufficient attention to wind from the side etc., and observe the speed limit. Please limit the installation of bicycle attachments and bicycles to the roof carrier to two sets. 13 / 13