Challenger Neon Air Hockey Table Owners Manual

Similar documents
Quadair. Air Hockey Table Owners Manual. Assembly operation and care instuctions. Serial # Distributed By. Sales Person. Technical Service #

Table of Contents - 2 -

Table of Contents - 2 -

When your Rock-N-Bowl was shipped from the factory, the dipswitches were set as follows:

TOURNAMENT ICE. 8Ft-Gold Standard Manual Score Home Air Hockey Game Assembly Instructions / Manual

J12 TICKET DISPENSER HOPPER ALL STOP STOP 1 STOP 2 STOP 3 BIG DOUBLE SMALL TAKE PLAY START CURRENT PRODUCTION BOARD TYPE

Coastal Amusements 1935 Swarthmore Ave. Lakewood NJ Tel: (732) Fax: (732)

TECHNICAL INFORMATION

8Ft-Gold Standard Coin/Home Air Hockey Game Assembly Instructions / Manual

ASSEMBLY INSTRUCTIONES

Thank you for purchasing your new Empire Reloader B Sound-Activated 3-Speed Paintball Hopper!

Agilent 1220 Infinity II LC Mobile Upgrade Kit

UNIVERSITY OF ROCHESTER ENVIRONMENTAL HEALTH & SAFETY

Basketball Instructions

I.H.S INSTALLATION INSTRUCTIONS

AutoChanger Installation & User Guide Issue 2

T i m i n g S y s t e m s. RACEAMERICA, Inc. P.O. Box 3469 Santa Clara, CA (408)

Calcium Reactor. CalcFeeder PRO. User Manual 1.1a. Model. CalcFeeder AC1 PRO CalcFeeder AC2 PRO CalcFeeder AC3 PRO CalcFeeder AC4 PRO

USER MANUAL

Service Installation: 48 V Power Supply September 27, 2018 SI Written by BTA

YSC-8330 USER MANUAL XI AN TYPICAL INDUSTRIES CO.,LTD.

PARTS IDENTIFIER HARDWARE

icreasepro Creaser Operators Manual

INSTRUCTIONS FOR THE 7FT REVOLVER 3-IN-1 MULTIGAMES TABLE

FX134, FX1234, FX3030 Problem and Solutions

Stand-Alone Bubble Detection System

Maintenance Manual. Note: This document is broken up into the following 6 sections of prescribed maintenance.

OEM Manual MODEL 2305 ECONOMICAL DIGITAL SINGLE CYLINDER SCALE

INSTRUCTION MANUAL. 840 Transmitter. Loop Powered Dissolved Oxygen Transmitter

Rev I MEGATOUCH ELITE EDGE ION ASSEMBLY 1

SI-F971A. 9-speed super narrow chain such as CN-7700 / CN-HG92 8- / 7- / 6-speed narrow chain such as CN-HG50 / CN-IG51

Misaligned Folds Paper Feed Problems Double Feeds Won t Feed FLYER Won t Run iii

GEN-1e CO2 Generator OVERVIEW INSTALLATION PROPANE GENERATORS ONLY NATURAL GAS GENERATORS ONLY

MODEL 9875 STADIUM BASEBALL SCOREBOARD. Instruction Manual

Read Before Operating!

Napa Technology Trouble Shooting. For Premier & Premier PLUS Models

Software version: BA4US4F

INSTALLATION PROCEDURE 1/4 & 1/8 MILE PERMANENT TRACK

User Manual GRI- 1500Li

Model PSI Compressor with 3-Gallon Air Tank 12VDC

Operating Instructions Model and Hydrostatic Test Pump

FT500GF Dat e Code: 2 - FT500GF - - MW Purchase Date: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE. All Rights Reserved

Under Basin Storage Unit

IMPORTANT SAFETY INSTRUCTIONS

7130 Lancer Rear Drive Magnetic Commercial Indoor Cycling Bike

Arbor Terminator Press Operation Manual For IDT Connectors Order No Engineering No: AM

Santa Fe Cycles Assembly Guide Introduction

AUTOMATIC GAS MANIFOLDS

A-FRAME RESIN IN & OUT FLIP UP LADDER

BELT DRIVE INDOOR CYCLING BIKE SF-B1712 USER MANUAL

Syringe, Distribution Valve and Infusion Pump Removal/Replacement ATTENTION SYRINGE REPLACEMENT

Sterisil Ac+ Installation & Operating Manual

S4W PRO ROBOT. User Manual. paddlepalace.com

User Manual V14.1 IP68 LED FLEX NEON

TorMinal. Operating instructions V OCE-Rev.L_EN

Please have your date code when inquiring about parts.

Preferred Instruments Danbury, CT USA

ProMaster Troubleshooting Guide

UsER manual for Watersens ph -REDOX

September 10, 2014 Revision 2. Puncher Unit-BE1/BF1/BG1/BH1 Service Manual

OUTDOOR LED SCOREBOARD CARE & OPERATIONS MANUAL

Paddle Bar Replacement

A4 Operation Manual. Fig.1-1 Controller Socket Diagram

INTRODUCTION TABLE CHIPS WINBET BETTING AREAS SPIN BET TIMER UNDO / REDO/CLEAN / REPEAT/ DOUBLE SYSTEM SET UP

TECHNICAL INFORMATION

Magnetic Bike. Model No: AENERGISER BODY WORX. Retain this owner s manual for future reference Read and follow all instructions in this owner s manual

Cable Replacement Instructions for R-Series Roust-A-Bout 100/150/250

Portable Automatic Gas Cutter

A4s Operation Manual

O P E R ATING INSTRUCTIONS FOR MODEL SPR-45 Automatic Screen and Stencil Printer

1. Hardware Bookkeeping & Adjustment...7. Access Flow Chart... 7 System Adjustment... 8 Chance Adjustment... 9 Touch Screen Calibration...

PROPORTIONING VALVE. Model 150 INSTRUCTION MANUAL. March 2017 IMS Company Stafford Road

G2W PRO ROBOT. User Manual. paddlepalace.com

ABRASIVE SYSTEM ABRASIVE REGULATOR II 800# BULK ABRASIVE DELIVERY POT Abrasive Regulator II and 800# Pot Manual

AiM User Guide. on Yamaha YZF-R1 and YZF- R (YEC included) Release 1.05

Yoke Block Instruction Manual

BASIC TALLBOY MIRROR CABINET

ECE 477 Digital Systems Senior Design Project Rev 9/12. User Manual

Batter Up & Bowl Sports Arena

OPERATION MANUAL DIVE CALIPER NOT SCALE / IF IN DOUBT ASK* *ALL UNITS IN MM/DEGREES UNLESS SPECIF. Dive Caliper General DC-051

Underwater Housing for Panasonic Lumix DMC-ZS60, DMC-TZ80

MAGNETIC CYCLING TRAINER SF-B0419 USER MANUAL

PRODUCT MANUAL Glass Touch RGB Controller 12V-24V

Instant Garage 20' x 12' 3" x 8' 3"

FAULT CODE TROUBLESHOOTING INDEX

TRAILMATE METEOR ASSEMBLY MANUAL

DRS4-RM Manual. Set Up Instructions for DRS4 Series Single Tank

OWNER'S MANUAL LOCK-N-LOAD BULLET FEEDER (PISTOL)

PURA. Pure Gas Dewpoint Transmitter. Users Guide

100C Air Compressor Kit

Operating Instructions for BAIR22-6 AIR-POWERED CRIMPING TOOL

200 PSI COMPRESSORS - MODEL NUMBERS

DM-RARD (English) Dealer's Manual. ROAD MTB Trekking. City Touring/ Comfort Bike. Rear Derailleur DURA-ACE RD-R9100 ULTEGRA RD-R8000

GATOR Battery-powered Pistol Grip Cable Cutters

Model 400ML Audible Information Device

Relay Judging Platforms with Speedlights

420C AIR COMPRESSOR KIT PART NO C AIR COMPRESSOR KIT PART NO

4 ANGLE GRINDER MODEL NO: CAT 52 PART

References 6 k thermal overload relays, adjustable from 0.11 to 16 A

Chapter 2 Rigging. Cutting Wire Rope. Anchoring Wire Rope to Drum. Winding Wire Rope Onto Drum

Transcription:

Challenger Neon Air Hockey Table Owners Manual Assembly operation and care instructions. Version 1.1.08

Index Weights and Dimensions 1 Table Assembly 2 Side Score Board Assembly 3 PCB Layout and Specification 10 Operator Program Adjustment 14 Care and Maintenence 16 Troubleshooting 17

Weight Overhead Bar Table Legs Total Weight 9lbs 300lbs 48lbs 357lbs Dimensions Length 89 Width 52 Height 57 1

Attach the legs to the table with the medium screws provided with washers. The blower has already been attached. Remove the keys taped to the bottom of the table. 2

Use 4 people to flow the table to the standing position. 3

4 Open the door and remove the kit with the pucks and mallets, and polish spray for play.

Lockable Cash Box 5

Scoreboard Overhead Bar Scoreboard Cable Overhead Bar Bracket Two Medium Screws Connect the corresponding pins from the cable running up the bar to the scoreboard, connecting to the matching color and shape of the pin. Attach the overhead scoreboard to the bar with two medium screws to the bar. 6

Remove sticky surface from the chrome side of the holders of the side guards. Remove protective covering off the side safe guards. Using the small screws, attach the Plexiglas side safe guards with the chrome side out. Using small screws, attach the Plexiglas and holder to the table. DO NOT screw too tight, Plexiglas may crack. Attach top half of the side safe guard chrome holder to the plexiglass. Attach the bottom half to the table. 7

Attach side score board cable from the bar to the side of the table, connecting to the matching color and shape of the pin. Attach the overhead bar holder to the table with medium screws. DO NOT TIGHTEN. Push bar into holder on both sides of the table. When the bar is completely into the holder, tighten the bracket with the bar in it securely to the air hockey table. Attach white cover plate over bar bracket using the large screws. 8

Make sure all screws are tight and secure. Adjust the table to the desired height. Use a level to ensure fair play and a balanced table. Plug in the table to a 110Volt system. 9

CON 35: A1, Signal In/Out Controller CON 36: B1, Signal In/Out Controller CON 38: A2, Puck Strike Detector CON 39: B2, Puck Strike Detector CON31: Neon Lamp Speed Control CON 310: Turbine Engine CON 311: Solenoid Control CON 312: AC Power CON 313: DC Power [GND+5V+12V] CON 315: Left/Right Speaker V31: Volume Control 10

3. Coin Mechanism 2. Start Button 1. Sensor 4. Ticket Unit 5. Hitting Sound for rails 6. Programmable Settings SW11 7. Programmable Settings SW12 11

CON 38 Orange/Brown 1. +5V White 2. Strike Detect Black/Blue 3. Ground CON 39 Orange/Black/Brown 1. +12V White 2. Strike Detect Black/White/Blue 3. Ground CON 31 1. 2. 3. CON 310 Brown 1. AC110V or AC220V Blue 2. AC110V or AC220V CON 311 Orange 1. +12V Purple 2. Signal Control Orange 3. +12V Grey 4. Signal Control CON312 Brown 1. AC110V or AC220V Green/Yellow 2. AC110V or AC220V Blue 1. AC110V or AC220V CON 313 Orange 1. +12V 2. Black 3. Ground 4. Red 5. +5V CON 315 1. SP+ 2. SP- 3. SP+ 4. SP- A2. Puck Strike Detector (Send, Receive) B2. Puck Strike Detector (Send, Receive) Turbine Engine Power Out A1 Solenoid SW B1 Solenoid SW AC Power In DC Power In Left Speaker Right Speaker 12

CON 35 S2 1. +5V White 2. Puck In Detect Black 3. Ground Brown 4. Start Black/White 5. Ground Orange/Black 6. 12V Blue 7. Counter Orange 8. +12V Green 9. Coin Selector Black 10. Ground Blue 11. SR Orange 12. +12V Black 13. Ground Purple 14. Ticket CON 36 Red 1. +5V White/Red 2. Puck In Detect Black 3. Ground Yellow 4. Start Black/White 5. Ground Orange/Orange 6. 12V Brown/Orange/Yellow/Black 7. Start Lamp Orange 8. +12V Black 9. Coin Selector Blue/Orange 10. Ground Orange 11. SSR Black 12. +12V Purple 14. Ticket A1. Goal Sensor A1. Start Counter A1. Coin Selector A1. Ticket Dispenser B1. Goal Sensor B1. Start Start Lamp B1. Coin Selector B1. Ticket Dispenser 13

SW11 - Upper Dipswitch Unit Operator Programmable Settings Air Hockey Dip Switch Adjustment O = OFF: Switch is Down I = ON: Switch is Up Coin Acceptor Tickets Dispensed Side Strike Sound Function Upper Unit SW11 1 Coin= 1 Credits I I I 1 Coin= 2 Credits O I I 1 Coin= 3 Credits I O I 1 Coin= 4 Credits O O I 2 Coins= 1 Credits I I O 3 Coins= 1 Credits O I O 4 Coins= 1 Credits I O O FREE PLAY* NONE 1 2 3 4 5 6 7 8 O O O O O O Winner 3 Loser 1 I O O Winner 6 Loser 2 O I O Winner 9 Loser 3 O I I Winner 18 Loser 4 O O I Winner 22 Loser 5 I O I Winner 26 Loser 6 O I I Winner 36 Loser 7 I I I Sound A I I Sound B O I Sounds C I O No Sound Switch Number O O *Free play only works with an upgrade package of free play start button through Baron Games International. 14

SW12 - Lower Dipswitch Unit Operator Programmable Settings Air Hockey Dip Switch Adjustment O = OFF: Switch is Down I = ON: Switch is Up Goal To Win Time of Credit Ticket Recipient Demo Sound Function Lower Unit SW12 No Limit 1 2 3 4 5 6 7 8 O O O 9 O O I 8 O I O 7 I I O 6 O O I 5 I O I 4 O I I 3 I I I No Limits O O O 10 Minutes I O O 8 O I O 6 I I O 4 O O I 3 I O I 2 O I I 1 I I I Winner Only Both Enabled Disbled Switch Number I O I O 15

Care and Maintenance Turn the adjustable leg bolts to create a leveled playing field. Place puck in the middle of the table, if it moves to a certian side; raise accordingly. Avoid direct sunlight if table is placed outdoors. Avoid exposure to wetness when placed in basement or wet area. Do not shake or drop when transporting. Replace puck when moving slowly during game play. Light sanding of puck can also smooth puck. Check air holes periodically to ensure smooth air hockey play. Do not use sharp objects on playfield. Keep table surface always clean and dust free. When cleaning table surface use a soft dry cloth and polishing spray. DO NOT APPLY WATER. DO NOT APPLY AMONIA BASED PRODUCTS such as window/glass cleaner. Polish Sray/Wax is provided inside the mallet kit. Contact Barron Games for more if needed. Polish Spray/Wax table monthly to ensure best playfield. Wax the table surface periodically to ensure smooth air hockey play. 16

Troubleshooting I. PC Board Lights If lights on PC Board are on for coin mechanism and/or ticket dispenser, there is an error for the corresponding light(s). II. Ticket Dispenser: Flashing light on ticket dispenser means out of tickets. Restart table if light does not appear with new tickets inserted. III. Coin Mechanism/Acceptor Make sure to replace the sample plastic coin with the desired number of coins. Coin Acceptor must be on N.O. (normally open) setting. IV. Puck Release If puck is getting stuck inside of the release door, the following need to be check for possible errors: 1) Check for debris, shavings, paper and other emains lodged inside the return unit. 2) Puck has chips not allowing it to fall through the return unit. Replace or sand puck. 3) Wire connector to release solenoid has become unplugged/ damaged/stuck/broken. 4) Release solenoid needs to be replaced. Contact Barron Games for spare parts. V. Push Start Sound If you hear PUSH START, the following need to be checked and corrected. It is an error message. Restart the table after every time changes/new settings are made. ON/OFF switch is underneath the table, next to the power display. 1) Machine is out of tickets. 2) Both coin acceptors and ticket dispensers are properly plugged in and connected. 3) Any damage to connection pins/other wires. 4) Make sure both ticket dispensers are on the following settings N.O. (Normally Open) and not on continuous dispense. 5) Both coin acceptors are on the N.O. (Normal Open) settings. 6) The correct numbers of coins have inserted to play the game. VI. NOTE: There is no start button located on commercial air hockey machines. You may purchase a start button and faceplate through Barron Games for residential use. Barron Games International LLC. Tech Support and Parts Service phone number 1(716) 866-0054 USA or email info@barrongames.com. More information/updates can be found at www.barrongames.com. Manufactured by YUAN GONG - Taiwan 17

4248 Ridge Lea Road Suite 110 Amherst, New York 14226, USA Phone: 1 (716) 866-0054 Fax: 1 (716) 992-7077 E-mail: info@barrongames.com Visit: www.barrongames.com!