Page 1 of 6 SECTION 1: Identification of the substance/mixture and of the company/undertaking 1.1. Product identifier 1.2. Relevant identified uses of the substance or mixture and uses advised against Use of the substance/mixture Silicone Sealant/adhesive 1.3. Details of the supplier of the safety data sheet Company name: Street: Lilienthalstraße 7 Place: GB-82205 Gilching Telephone: 08105-217-0 Telefax: 08105-217-33 e-mail: Forster-Hummel@ego.de P.Goldmann@ego.de Contact person: Eva Forster-Hummel; Telephone: - 28; -27 Petra Goldmann Internet: http://www.ego.de Responsible Department: Labor 1.4. Emergency telephone number: SECTION 2: Hazards identification 2.1. Classification of the substance or mixture (+49)55119240 (24h/7d) GIZ-Nord, Göttingen Member of EPECs network Regulation (EC) No. 1272/2008 This mixture is not classified as hazardous according to Regulation (EC) No. 1272/2008. 2.2. Label elements SECTION 3: Composition/information on ingredients 3.2. Mixtures Chemical characterization Silicone resin + Paint filler(s). Further Information To the standard of our knowledge the product does not contain any additional substances that, in the concentrations indicated, are classified as harmful or dangerous for the environment and would therefore have to be listed in this section. SECTION 4: First aid measures 4.1. Description of first aid measures After inhalation Call a physician if symptoms occur. After contact with skin Wash off with soap and water. Remove contaminated clothing and shoes. Call a physician if symptoms occur. After contact with eyes In case of eye contact, remove contact lens and rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Consult a physician. After ingestion Gently wipe or rinse the inside of the mouth with water. If victim is fully conscious, give a cupful of water. Do
Page 2 of 6 not induce vomiting without medical advice. Obtain medical attention. 4.2. Most important symptoms and effects, both acute and delayed Product specific hazards: None known. 4.3. Indication of any immediate medical attention and special treatment needed Treat symptomatically. SECTION 5: Firefighting measures 5.1. Extinguishing media Suitable extinguishing media Use water spray, alcohol-resistant foam, dry chemical or carbon dioxide. Unsuitable extinguishing media None known. 5.2. Special hazards arising from the substance or mixture Hazardous decomposition products formed under fire conditions. Carbon dioxide (CO2), Carbon monoxide, metal oxides. 5.3. Advice for firefighters Prevent unauthorised persons entering the zone. SECTION 6: Accidental release measures 6.1. Personal precautions, protective equipment and emergency procedures Prevent unauthorised persons entering the zone. 6.2. Environmental precautions Do not flush into surface water or sanitary sewer system. If the product contaminates rivers and lakes or drains inform respective authorities. Discharge into the environment must be avoided. 6.3. Methods and material for containment and cleaning up Use mechanical handling equipment. Contaminated surfaces will be extremely slippery. Clean contaminated surface thoroughly. 6.4. Reference to other sections See also section 8, 13 SECTION 7: Handling and storage 7.1. Precautions for safe handling Advice on safe handling Smoking, eating and drinking should be prohibited in the application area. Wash hands before breaks and at the end of workday. Avoid contact with skin, eyes and clothing. 7.2. Conditions for safe storage, including any incompatibilities Requirements for storage rooms and vessels Keep containers tightly closed in a dry, cool and well-ventilated place. Keep away from direct sunlight. Keep away from food, drink and animal feedingstuffs. SECTION 8: Exposure controls/personal protection 8.1. Control parameters Additional advice on limit values We are not aware of any national exposure limit. 8.2. Exposure controls
Page 3 of 6 Appropriate engineering controls Ensure adequate ventilation, especially in confined areas. Protective and hygiene measures Remove and wash contaminated clothing before re-use. Wash hands before breaks and at the end of workday. Wash hands before eating, drinking, or smoking. Eye/face protection Safety glasses Hand protection Chemical resistant gloves made of butyl rubber or nitrile rubber category III according to EN 374. As the product is a mixture of several substances, the durability of the glove materials cannot be calculated in advance and has to be tested before use. Request information on glove permeation properties from the glove supplier. Gloves should be discarded and replaced if there is any indication of degradation or chemical breakthrough. Barrier creams may help to protect the exposed areas of skin, they should however not be applied once exposure has occurred. Skin protection impervious clothing Respiratory protection Not required SECTION 9: Physical and chemical properties 9.1. Information on basic physical and chemical properties Physical state: Colour: Odour: ph-value: Changes in the physical state Melting point: Initial boiling point and boiling range: Flash point: Flammability Solid: Explosive properties Lower explosion limits: Upper explosion limits: Ignition temperature: Decomposition temperature: Vapour pressure: Density (at 20 C): Water solubility: SECTION 10: Stability and reactivity paste off-white odourless >244 C 1,39 g/cm³ insoluble Test method
Page 4 of 6 10.1. Reactivity 10.2. Chemical stability Stable under recommended storage conditions. 10.3. Possibility of hazardous reactions No dangerous reaction known under conditions of normal use. 10.4. Conditions to avoid 10.5. Incompatible materials 10.6. Hazardous decomposition products No decomposition if used as directed. SECTION 11: Toxicological information 11.1. Information on toxicological effects Toxicocinetics, metabolism and distribution Irritation and corrosivity Sensitising effects STOT-single exposure Severe effects after repeated or prolonged exposure No known effect. Carcinogenic/mutagenic/toxic effects for reproduction Aspiration hazard Specific effects in experiment on an animal Additional information on tests SECTION 12: Ecological information 12.1. Toxicity 12.2. Persistence and degradability 12.3. Bioaccumulative potential 12.4. Mobility in soil 12.5. Results of PBT and vpvb assessment
Page 5 of 6 12.6. Other adverse effects No known effect. Further information Do not allow contact with soil, surface or ground water. Do not let product enter drains. SECTION 13: Disposal considerations 13.1. Waste treatment methods Advice on disposal In accordance with local and national regulations. Waste disposal number of used product 080410 WASTES FROM THE MANUFACTURE, FORMULATION, SUPPLY AND USE (MFSU) OF COATINGS (PAINTS, VARNISHES AND VITREOUS ENAMELS), ADHESIVES, SEALANTS AND PRINTING INKS; wastes from MFSU of adhesives and sealants (including waterproofing products); waste adhesives and sealants other than those mentioned in 08 04 09 Contaminated packaging Empty remaining contents. Can be disposed of as a solid waste or burned in a suitable installation subject to local regulations. SECTION 14: Transport information Land transport (ADR/RID) 14.1. UN number: 14.2. UN proper shipping name: 14.3. Transport hazard class(es): 14.4. Packing group: Marine transport (IMDG) 14.1. UN number: 14.2. UN proper shipping name: 14.3. Transport hazard class(es): 14.4. Packing group: Marine pollutant: no Air transport (ICAO) 14.1. UN number: 14.2. UN proper shipping name: 14.3. Transport hazard class(es): 14.4. Packing group: 14.5. Environmental hazards ENVIRONMENTALLY HAZARDOUS: 14.6. Special precautions for user 14.7. Transport in bulk according to Annex II of MARPOL73/78 and the IBC Code SECTION 15: Regulatory information no 15.1. Safety, health and environmental regulations/legislation specific for the substance or mixture EU regulatory information
Page 6 of 6 2004/42/EC (VOC): National regulatory information Water contaminating class (D): 15.2. Chemical safety assessment 0% 1 - slightly water contaminating Chemical safety assessments for substances in this mixture were not carried out. SECTION 16: Other information Changes This data sheet contains changes from the previous version in section(s): 2,4,6,8,9,10,11,12,14,15. Further Information These data describe only the safety requirements for the product(s) and are based on our present knowledge. However, they do not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship. (The data for the hazardous ingredients were taken respectively from the last version of the sub-contractor's safety data sheet.)