The Study on the Influence of Gust Wind on Vehicle Stability Chen Wang a, Haibo Huang b*, Shaofang Xu c

Similar documents
Study on the Influencing Factors of Gas Mixing Length in Nitrogen Displacement of Gas Pipeline Kun Huang 1,a Yan Xian 2,b Kunrong Shen 3,c

Aerodynamic Performance of 160km Box Car

Numerical Simulation of the Basketball Flight Trajectory based on FLUENT Fluid Solid Coupling Mechanics Yanhong Pan

NUMERICAL SIMULATION OF STATIC INTERFERENCE EFFECTS FOR SINGLE BUILDINGS GROUP

Characteristics of Decompression Tank Internally Pressurized With Water Using OpenFOAM Syamsuri 1, a

Aerodynamic Measures for the Vortex-induced Vibration of π-shape Composite Girder in Cable-stayed Bridge

Aerodynamic Performance of Trains with Different Longitudinal Section Lines under Crosswind

Aerodynamic Shape Design of the Bow Network Monitoring Equipment of High-speed Train

Keywords: dynamic stall, free stream turbulence, pitching airfoil

Single Phase Pressure Drop and Flow Distribution in Brazed Plate Heat Exchangers

Influence of rounding corners on unsteady flow and heat transfer around a square cylinder

Aerodynamic Performance Comparison of Head Shapes for High-Speed Train at 500KPH

Structural Design and Analysis of the New Mobile Refuge Chamber

NUMERICAL SIMULATION OF WIND INTERFERENCE EFFECT

Wind tunnel tests of a non-typical stadium roof

High Swept-back Delta Wing Flow

The Mechanism Study of Vortex Tools Drainage Gas Recovery of Gas Well

CFD Analysis ofwind Turbine Airfoil at Various Angles of Attack

Numerical Simulation And Aerodynamic Performance Comparison Between Seagull Aerofoil and NACA 4412 Aerofoil under Low-Reynolds 1

Numerical simulation and analysis of aerodynamic drag on a subsonic train in evacuated tube transportation

OPTIMIZING THE LENGTH OF AIR SUPPLY DUCT IN CROSS CONNECTIONS OF GOTTHARD BASE TUNNEL. Rehan Yousaf 1, Oliver Scherer 1

CFD ANALYSIS OF AIRFOIL SECTIONS

Wind tunnel test and numerical simulation of wind pressure on a high-rise building

Determination of the wind pressure distribution on the facade of the triangularly shaped high-rise building structure

CFD Study of Solid Wind Tunnel Wall Effects on Wing Characteristics

Ermenek Dam and HEPP: Spillway Test & 3D Numeric-Hydraulic Analysis of Jet Collision

Centre for Offshore Renewable Energy Engineering, School of Energy, Environment and Agrifood, Cranfield University, Cranfield, MK43 0AL, UK 2

HYDROGEN FAST FILLING TO A TYPE IV TANK DEVELOPED FOR MOTORCYCLES

Numerical simulation of aerodynamic performance for two dimensional wind turbine airfoils

CFD Analysis and Experiment Study of the Rotary Two-Stage Inverter Compressor with Vapor Injection

COMPUTATIONAL FLUID DYNAMIC ANALYSIS OF AIRFOIL NACA0015

Analysis of Steady-state Characteristics of Aerodynamic Bearing Based on FLUENT JIA Chenhui 1,a, Du Caifeng 2,b and QIU Ming 3,c

Research on Small Wind Power System Based on H-type Vertical Wind Turbine Rong-Qiang GUAN a, Jing YU b

Study by numerical simulations on the breathing effect in a semi-underground highway with beams and a roof above it

Effect of Diameter on the Aerodynamics of Sepaktakraw Balls, A Computational Study

COMPARISONS OF COMPUTATIONAL FLUID DYNAMICS AND

EXPERIMENTAL AND ANALYTICAL INVESTIGATION OF THE EFFECT OF BODY KIT USED WITH SALOON CARS IN BRUNEI DARUSSALAM

Some Geometric and Kinematics Properties of Breaking Waves

Computer Simulation of a Train Exiting a Tunnel through a Varying Crosswind

Investigation of Suction Process of Scroll Compressors

Surrounding buildings and wind pressure distribution on a high rise building

The influence of the high-speed Trimaran to Flow Field. Yi-fan Wang 1, Teng Zhao 2

2-D Computational Analysis of a Vertical Axis Wind Turbine Airfoil

Aerodynamic Analysis of Small Propeller in Wind Field Using CFD Chuansheng Zhang1, a, Shengguang Xie2,b and Tianhao Qin3,c

Finite Element Modal Analysis of Twin Ball Screw Driving Linear Guide Feed Unit Table

CFD ANALYSIS AND COMPARISON USING ANSYS AND STAR-CCM+ OF MODEL AEROFOIL SELIG 1223

Analysis of the Impact of Rotor Rigidity on the Aerodynamic Performance of Vertical Axis Wind Turbines

CFD Analysis of Giromill Type Vertical Axis Wind Turbine

RESEARCH ON THE WIND LOAD PARAMETERS AND THE WIND FENCES BEHAVIOR FOR WIND FENCES OF RAILWAY BRIDGE

A numerical simulation of oil spill in Istanbul strait

NUMERICAL INVESTIGATION OF FLOW OVER MULTI- ELEMENT AIRFOILS WITH LIFT-ENHANCING TABS

NUMERICAL INVESTIGATION OF THE FLOW BEHAVIOUR IN A MODERN TRAFFIC TUNNEL IN CASE OF FIRE INCIDENT

Center Distance Change of Silent Chain Drive Effect on Sprocket Tooth Profile Modification Wei Sun 1,a, Xiaolun Liu 1,b, Jiajun Liu 1 and Wei Zhang 1

Investigation on 3-D Wing of commercial Aeroplane with Aerofoil NACA 2415 Using CFD Fluent

Journal of Chemical and Pharmaceutical Research, 2016, 8(6): Research Article. Walking Robot Stability Based on Inverted Pendulum Model

Development of Biomimicry Wind Louver Surface Design

Stability and Computational Flow Analysis on Boat Hull

AIRFLOW GENERATION IN A TUNNEL USING A SACCARDO VENTILATION SYSTEM AGAINST THE BUOYANCY EFFECT PRODUCED BY A FIRE

Numerical simulation on down-hole cone bit seals

Analysis of wind resistance of high-rise building structures based on computational fluid dynamics simulation technology

SIMULATION OF THE FLOW FIELD CHARACTERISTICS OF TRANSIENT FLOW

The Usage of Propeller Tunnels For Higher Efficiency and Lower Vibration. M. Burak Şamşul

THEORETICAL EVALUATION OF FLOW THROUGH CENTRIFUGAL COMPRESSOR STAGE

Inlet Swirl on Turbocharger Compressor Performance

ANALYSIS OF THE POSITIVE FORCES EXHIBITING ON THE MOORING LINE OF COMPOSITE-TYPE SEA CAGE

Numerical and Experimental Investigations of Lift and Drag Performances of NACA 0015 Wind Turbine Airfoil

Australian Journal of Basic and Applied Sciences. Pressure Distribution of Fluid Flow through Triangular and Square Cylinders

Volume 2, Issue 5, May- 2015, Impact Factor: Structural Analysis of Formula One Racing Car

Influence of Ventilation Tube Rupture from Fires on Gas Distribution in Tunnel

Experimental and Theoretical Investigation for the Improvement of the Aerodynamic Characteristic of NACA 0012 airfoil

WIND FORCES ACTING ON INFLATABLE AMUSEMENT PRODUCTS AND CRITICAL WIND SPEEDS CAUSING ACCIDENTS

The investigation of car movement trajectories after contact in the case of collisions with stationary safety barriers

CFD AND EXPERIMENTAL STUDY OF AERODYNAMIC DEGRADATION OF ICED AIRFOILS

CFD SIMULATION STUDY OF AIR FLOW AROUND THE AIRFOIL USING THE MAGNUS EFFECT

Study on Fire Plume in Large Spaces Using Ground Heating

Study on the shape parameters of bulbous bow of. tuna longline fishing vessel

CRITERIA OF BOW-DIVING PHENOMENA FOR PLANING CRAFT

Wind loads investigations of HAWT with wind tunnel tests and site measurements

Pressure coefficient on flat roofs of rectangular buildings

FREE MOTION SIMULATION OF A SAILING YACHT IN UP-WIND CONDITION WITH ROUGH SEA

Aerodynamic study of a cyclist s moving legs using an innovative approach

AIS data analysis for vessel behavior during strong currents and during encounters in the Botlek area in the Port of Rotterdam

Simulation Research of a type of Pressure Vessel under Complex Loading Part 1 Component Load of the Numerical Analysis

APPLICATION OF COMPUTATIONAL FLUID DYNAMICS (CFD) IN WIND ANALYSIS OF TALL BUILDINGS. Damith Mohotti, Priyan Mendis, Tuan Ngo

Numerical Investigation of Multi Airfoil Effect on Performance Increase of Wind Turbine

CFD SIMULATIONS OF GAS DISPERSION IN VENTILATED ROOMS

A COMPARATIVE STUDY OF MIX FLOW PUMP IMPELLER CFD ANALYSIS AND EXPERIMENTAL DATA OF SUBMERSIBLE PUMP

AERODYNAMIC CHARACTERISTICS OF NACA 0012 AIRFOIL SECTION AT DIFFERENT ANGLES OF ATTACK

Figure 1. Outer dimensions of the model trucks.

Research on natural gas pipeline leakage and ventilation scheme in tunnel

Kinematics and Luffing Moment of Lemniscate Type Crane with Boom. Driving

Development of Technology to Estimate the Flow Field around Ship Hull Considering Wave Making and Propeller Rotating Effects

Effect of High-Lift Devices on Aircraft Wing

FLOW CONSIDERATIONS IN INDUSTRIAL SILENCER DESIGN

Basis of Structural Design

Research on Goods and the Ship Interaction Based on ADAMS

OPTIMIZATION OF SINGLE STAGE AXIAL FLOW COMPRESSOR FOR DIFFERENT ROTATIONAL SPEED USING CFD

Experimental study on aerodynamic characteristics of vertical-axis wind turbine

INTERACTION BETWEEN WIND-DRIVEN AND BUOYANCY-DRIVEN NATURAL VENTILATION Bo Wang, Foster and Partners, London, UK

Vibration Analysis and Test of Backup Roll in Temper Mill

Transcription:

Applied Mechanics and Materials Submitted: 214-6-4 ISSN: 1662-7482, Vol. 598, pp 198-21 Accepted: 214-6-4 doi:1.428/www.scientific.net/amm.598.198 Online: 214-7-16 214 Trans Tech Publications, Switzerland The Study on the Influence of Gust Wind on Vehicle Stability Chen Wang a, Haibo Huang b*, Shaofang Xu c Faculty of Mechanical Engineering and Mechanics, Ningbo University, China a wangchen1@163.com, b* huanghaibo2@163.com, c xsf6715121@sina.com Key words: CFD, gust wind, six-component force, vehicle stability Abstract. In this paper, the vehicle driving characteristics are investigated under different Force level of gust wind based on the CFD theory. The distributed pressure acted on the vehicle side surface is equivalent to the six-component force on vehicle gravity center. The six-component force are explored and compared in different Force level of gust wind. The results show that the lateral force Fy and yaw moment Mz vary with v shape and Λ shape under gust wind, respectively. The slopes of the result curves increase with greater Force level of gust wind. Gust wind gives most influence on Fy and Mz while has little effect on other component force. The work will provide a methodology for vehicle stability research under gust wind. Introduction The vehicle dynamics are affected by the gust wind. Gust wind causes transient force on the car body and it is dangerous on vehicle safety, which changes the distribution of the aerodynamic response on the vehicle. The severely gust wind alters the track of vehicle and sometimes cause severe traffic accidents. We can check aerodynamic performance of vehicle through the wind tunnel test or the numerical simulation. The wind tunnel experiment can well represent the influence of wind on the vehicle at the cost of long time and heavy consumption. With the development of numerical and computation method, the numerical method can also provide relative high precise simulations compared to the wind tunnel test and cost less. The position of the air pressure center acted on the vehicle is very important to the vehicle aerodynamics. In this paper we simplify the air pressure center equivalent to the center of mass because the air pressure center and center of mass are both on the symmetrical plane of the car body. The effect of gust wind on vehicle dynamics is equivalent to the six-component force acted on the vehicle[1]. Some simulations were done based on CFD software and the force inspired by gust wind looks on as the dynamic boundary conditions. Then we can investigate the influence of gust wind on vehicle dynamics through checking the six-component forces. And the vehicle stability can be explored under gust wind for different levels. The modeling The vehicle model. A simplified vehicle model is adopted in the simulation. The tire and rear view mirror are omitted on the car body which are allowable in the aerodynamic simulations [2-4]. The vehicle geometry is shown in Fig.1(a). All rights reserved. No part of contents of this paper may be reproduced or transmitted in any form or by any means without the written permission of Trans Tech Publications, www.ttp.net. (ID: 13.23.136.75, Pennsylvania State University, University Park, USA-19/2/16,13:4:2)

Applied Mechanics and Materials Vol. 598 199 wind speed/ m/s 2 18 16 14 12 1 8 6 4 2 From Force2 to Force 8 Force2 Force3 Force4 Force5 Force6 Force7 Force8 (a) The geometry of vehicle model (b) Computational region and meshed grid Fig.1 Schematic of the simulation system.1.3.5.7.9 1.1 1.3 1.5 1.7 1.9 Time/s (c) The speed variation of gust wind The computational geometric field. The simulation is investigated by using finite element commercial code, Fluent. The computational geometric field is a box shape with 2mm in length, 1mm in width and 6mm in height. The distance between the car body and field bottom is 3mm. And the distance between the car body and field top is 46mm. The grid is refined on and near the body surface for computation precision, as shown in Fig.1(b). The vehicle's traveling direction is with negative X axis while the wind's direction is with negative Y axis. The dynamic features of gust wind are very complex. Due to ref [5], the velocity of the wind follows sine function. The wind direction is perpendicular to direction of the vehicle driving. The wind is classified into 7 levels. The maximum values of velocity for various levels are: 2.5m/s, 4.4 m/s, 6.7 m/s, 8.8 m/s, 12.3 m/s, 15.5 m/s, 19. m/s, respectively. The wind lasts 1.8s (from.1s to 1.9s) and the wind velocity reaches the peak at t=1.s, as shown in Fig.1(c). Navier-Stokes equations and the turbulence model. Due to the aerodynamics, the Navier-Stokes equations and a suitable turbulence model are needed. The standard K ε turbulence model, which is usually used in vehicle's aerodynamic simulation, is applied. The detailed description for the equations and the model can be found in Ref[6]. And the parameters in the K ε turbulence model can be found in Ref[7]. The results and conclusion The influence of the gust wind on the vehicle six-component force. The paper takes gust wind of level 4 to investigate the influence of gust wind on vehicle driving stability. The six component force caused by gust wind of level 4 is shown in Fig2 (a) and (b). As shown in Fig.2 (a), the force acts on the vehicle in Y direction that is most influenced by the gust wind compared to the forces in other two directions and varies with "V" shpae. It is due to the sinusoid velocity of gust wind. Force in Y direction reaches the peak at t = 1. s, corresponding to the maximum wind velocity at the same time. The higher is the wind speed, the greater the lateral force Fy is. Fz in the vertical direction shows the shallow "V" shape trend. When the wind speed increases, Fz decreases and when the wind speed decreases, Fz increases. It is mainly because the upper half shape of the vehicle is tilted, especially the windows area. It will cause the pressure in negative Z direction under gust wind and leads the lift force reduced, guaranteeing adhesion between the tire and the ground. The force in longitudinal direction is almost constant and less affected by the gust wind. In Fig.2 (b), the yaw moment Mz varies obviously under the lateral winds, presenting Λ shape trend. It is opposite to the v-shape dynamic characteristics of gust wind. At t = 1. s, the yawing moment values reaches maximum. Yawing moment also corresponds with varies of gust wind. From Fig.2 (c), the car body bears the uneven lateral distribution of the wind pressure. The front body bears significantly larger pressure resulting in the asymmetry between the vehicle front and back, which causes large variations in the yawing moment of vehicles.

2 Advanced Materials, Mechanics and Industrial Engineering Rolling moment Mx and the longitudinal moment My change relatively small and gentle in amplitude. 4 5 Force/ N 3 2 1-1 -2 Moment/ N.m -5 Mx My Mz -3-4 Fx Fy Fz -5.5 1 1.5 2 Times/ s -1.5 1 1.5 2 Time/ s (a)the force component (b) The moment component (c) Pressure distribution on vehicle Fig. 2 The vehicle characteristics under Force 4 gust wind Fig.3 shows the six component force on gravity center when t=1s. As shown in Fig.3(a), Fy increases greater and its slope becomes bigger and bigger with the greater Level of the gust wind. Meanwhile, Fx and Fz vary slightly. 5 15 1 Force/N -5-1 Fx Fy Fz Moment / N.m 5-5 Mx My Mz -15-1 -2 2 3 4 5 6 7 8 Gust wind level (a) The force variation with gust wind speed variation Fig.3 Six component force variation at t=1s -15 2 3 4 5 6 7 8 Gust wind level (b) The moment variation with gust wind speed variation As shown in Fig.3(b), there is obvious rise for Mz with the greater gust wind. Meanwhile, Mx and My decline slightly, especially Mx. The force acted on the vehicle is related to the gust wind speed. Severe yaw moment Mz variation appears due to the violent lateral force variation and the body asymmetry. Longitudinal force Fx is mostly up to the vehicle speed so that Fx has little variation due to the vehicle constant speed. So is the rolling moment My. At the same time, vertical force Fz, is much influenced by the vehicle profile. It is composed of two parts: lift force caused by the vehicle driving speed in longitudinal direction and the vertical down force caused by the gust wind that acted on the slope part of the vehicle body. The force component increases with the wind energy. Conclusions (1) The lateral force Fy and yaw moment Mz change with V and Λ shape under the gust wind. The variation of other component force is slightly compared to Fy and Mz. (2) The lateral wind will be the dominant wind resistance factor when it is over Force 5, and go over the longitudinal wind. (3) The gust wind has great influence on lateral force Fy and yaw moment Mz. The offset distance increases with greater Force level of gust wind. When the Force level of gust wind is beyond 6, the rider will feel uncomfortable due to the greater lateral acceleration.

Applied Mechanics and Materials Vol. 598 21 Acknowledgements This research is supported by a grant from the Impact and Safety of Coastal Engineering Initiative, a COE Program of Zhejiang Provincial Government at Ningbo University (Grant No. zj118). References [1] Gu Zhengqi, Zhao Rongyuan, Yang Yi. Application of dynamic modeling of the in the cross-wind stability of automobile gas[j]. Journal of hunan university, 28.9(9):44-47. [2] Zhang Yingchao, Fu Limin. Transient Aerodynamic Numerical Simulation of simple shape cars enter process in tunnel[j]. Journal of Jilin University, 26.5(3): 32-36. [3] Li Yuzhou, Tan Xiamei, Liang MingYing. Analysis of automotive aerodynamics characteristics based on Ansys[J]. Mechanical design and manufacturing, 21.2(2):113-115. [4] Lan Tian, Kang Ning, Zheng Hao. Study on start-up phenomenon fastback car boot process[j]. Journal of Aerospace Power, 27. 11(11):1869-1873. [ 5 ] Chen Xiaodong, Zhan Zhangsong. CFD study of Changan automobile aerodynamics performance[j]. Automobile engineering, 26.9(1):873-875. [6] Li Jinliang, Li Chengxi, Hu Renxi. Proficiency in FLUENT6.3 flow field analysis[m]. Chemical Industry Press, 29.1. [ 7 ] Chen Hongye, Wang Ailing, Zheng Zhizhen. Under different crosswind aerodynamic characteristics of automobile simulation study[j]. Mechanical Management and Development, 21.4(114):81-82.

Advanced Materials, Mechanics and Industrial Engineering 1.428/www.scientific.net/AMM.598 The Study on the Influence of Gust Wind on Vehicle Stability 1.428/www.scientific.net/AMM.598.198