SAFETY DATA SHEET 1. Identification Product number Product identifier Company information Company phone Emergency telephone outside US Version # Recommended use Recommended restrictions 2. Hazard(s) identification Physical hazards Health hazards OSHA defined hazards Label elements 1000030317 SP744 MAX DEET SAWYER PRODUCTS, INC. 605 7TH AVENUE, N SAFETY HARBOR, FL 34695 United States 727-725-1177 1-952-852-4646 01 Pesticide ne known. Gases under pressure Acute toxicity, oral Skin corrosion/irritation Serious eye damage/eye irritation t classified. Compressed gas Category 4 Category 2 Category 2 Signal word Hazard statement Precautionary statement Prevention Response Storage Disposal Environmental hazards Hazard(s) not otherwise classified (HNOC) Supplemental information Warning Contains gas under pressure; may explode if heated. Harmful if swallowed. Causes skin irritation. Causes serious eye irritation. Wash thoroughly after handling. Do not eat, drink or smoke when using this product. Wear eye protection/face protection. Wear protective gloves. If swallowed: Call a poison center/doctor if you feel unwell. Rinse mouth. If on skin: Wash with plenty of water. If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If skin irritation occurs: Get medical advice/attention. If eye irritation persists: Get medical advice/attention. Take off contaminated clothing and wash before reuse. Protect from sunlight. Store in a well-ventilated place. Dispose of contents/container in accordance with local/regional/national/international regulations. Hazardous to the aquatic environment, acute hazard Hazardous to the aquatic environment, long-term hazard ne known. ne. Category 3 Category 3 3. Composition/information on ingredients Mixtures 1 / 8
Chemical name Common name and synonyms CAS number % N,n-diethyl-m-toluamide (DEET) 134-62-3 90-100 Other components below reportable levels 0.01-0.1 *Designates that a specific chemical identity and/or percentage of composition has been withheld as a trade secret. 4. First-aid measures Inhalation Skin contact Eye contact Ingestion Most important symptoms/effects, acute and delayed Indication of immediate medical attention and special treatment needed General information 5. Fire-fighting measures Suitable extinguishing media Unsuitable extinguishing media Specific hazards arising from the chemical Special protective equipment and precautions for firefighters Fire fighting equipment/instructions Specific methods General fire hazards Move to fresh air. Call a physician if symptoms develop or persist. Remove contaminated clothing. Wash with plenty of soap and water. If skin irritation occurs: Get medical advice/attention. Wash contaminated clothing before reuse. Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Get medical attention if irritation develops and persists. t likely, due to the form of the product. Rinse mouth. If vomiting occurs, keep head low so that stomach content doesn't get into the lungs. Get medical advice/attention if you feel unwell. Severe eye irritation. Symptoms may include stinging, tearing, redness, swelling, and blurred vision. Skin irritation. May cause redness and pain. Provide general supportive measures and treat symptomatically. Keep victim warm. Keep victim under observation. Symptoms may be delayed. Ensure that medical personnel are aware of the material(s) involved, and take precautions to protect themselves. Show this safety data sheet to the doctor in attendance. Water fog. Foam. Dry chemical powder. Carbon dioxide (CO2). Do not use water jet as an extinguisher, as this will spread the fire. During fire, gases hazardous to health may be formed. Self-contained breathing apparatus and full protective clothing must be worn in case of fire. In case of fire: Stop leak if safe to do so. Do not move cargo or vehicle if cargo has been exposed to heat. Move containers from fire area if you can do so without risk. Containers should be cooled with water to prevent vapor pressure build up. For massive fire in cargo area, use unmanned hose holder or monitor nozzles, if possible. If not, withdraw and let fire burn out. Use standard firefighting procedures and consider the hazards of other involved materials. Contents under pressure. Pressurized container may explode when exposed to heat or flame. 6. Accidental release measures Personal precautions, protective equipment and emergency procedures Methods and materials for containment and cleaning up Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Keep out of low areas. Many gases are heavier than air and will spread along ground and collect in low or confined areas (sewers, basements, tanks). Wear appropriate protective equipment and clothing during clean-up. Emergency personnel need self-contained breathing equipment. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Ventilate closed spaces before entering them. Local authorities should be advised if significant spillages cannot be contained. For personal protection, see section 8 of the SDS. Refer to attached safety data sheets and/or instructions for use. Stop leak if you can do so without risk. Move the cylinder to a safe and open area if the leak is irreparable. Isolate area until gas has dispersed. Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area). Keep combustibles (wood, paper, oil, etc.) away from spilled material. Prevent product from entering drains. Cover with plastic sheet to prevent spreading. Absorb in vermiculite, dry sand or earth and place into containers. Following product recovery, flush area with water. Environmental precautions Small Spills: Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination. For waste disposal, see section 13 of the SDS. Avoid release to the environment. Inform appropriate managerial or supervisory personnel of all environmental releases. Prevent further leakage or spillage if safe to do so. Avoid discharge into drains, water courses or onto the ground. 2 / 8
7. Handling and storage Precautions for safe handling Conditions for safe storage, including any incompatibilities Pressurized container: Do not pierce or burn, even after use. Do not use if spray button is missing or defective. Do not spray on a naked flame or any other incandescent material. Do not smoke while using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill, grind, or expose containers to heat, flame, sparks, or other sources of ignition. Ground and bond containers when transferring material. Close valve after each use and when empty. Protect cylinders from physical damage; do not drag, roll, slide, or drop. When moving cylinders, even for short distances, use a cart (trolley, hand truck, etc.) designed to transport cylinders. Suck back of water into the container must be prevented. Do not allow backfeed into the container. Purge air from system before introducing gas. Use only properly specified equipment which is suitable for this product, its supply pressure and temperature. Contact your gas supplier if in doubt. Do not re-use empty containers. Do not taste or swallow. Avoid contact with eyes, skin, and clothing. When using, do not eat, drink or smoke. Use only in well-ventilated areas. Wear appropriate personal protective equipment. Wash hands thoroughly after handling. Avoid release to the environment. Observe good industrial hygiene practices. Level 2 Aerosol. Contents under pressure. Do not expose to heat or store at temperatures above 120 F/49 C as can may burst. Do not puncture, incinerate or crush. Do not handle or store near an open flame, heat or other sources of ignition. Store in a well-ventilated place. Cylinders should be stored upright, with valve protection cap in place, and firmly secured to prevent falling or being knocked over. Stored containers should be periodically checked for general condition and leakage. Store away from incompatible materials (see Section 10 of the SDS). 8. Exposure controls/personal protection Occupational exposure limits Biological limit values Appropriate engineering controls exposure limits noted for ingredient(s). biological exposure limits noted for the ingredient(s). Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits. If exposure limits have not been established, maintain airborne levels to an acceptable level. Eye wash facilities and emergency shower must be available when handling this product. Individual protection measures, such as personal protective equipment Face shield is recommended. Wear safety glasses with side shields (or goggles). Eye/face protection Skin protection Hand protection Other Respiratory protection Thermal hazards General hygiene considerations Wear appropriate chemical resistant gloves. Suitable gloves can be recommended by the glove supplier. Wear appropriate chemical resistant clothing. If permissible levels are exceeded use NIOSH mechanical filter / organic vapor cartridge or an air-supplied respirator. Wear appropriate thermal protective clothing, when necessary. When using do not smoke. Keep away from food and drink. Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. 9. Physical and chemical properties Appearance Odor Physical state Form Color Odor threshold ph Melting point/freezing point Initial boiling point and boiling range Flash point Evaporation rate Gas. Aerosol. Compressed gas. 291.2 F (144.0 C) estimated 3 / 8
Flammability (solid, gas) t applicable. Upper/lower flammability or explosive limits Flammability limit - lower (%) Flammability limit - upper (%) Explosive limit - lower (%) Explosive limit - upper (%) Vapor pressure Vapor density Relative density Solubility(ies) Solubility (water) Partition coefficient (n-octanol/water) Auto-ignition temperature Decomposition temperature Viscosity Other information Explosive properties Flammability class Heat of combustion (NFPA 30B) Oxidizing properties 110-120 psig @20C estimated 392 F (200 C) estimated t explosive. Combustible IIIB estimated 28.2 kj/g estimated t oxidizing. 10. Stability and reactivity Reactivity Chemical stability Possibility of hazardous reactions Conditions to avoid Incompatible materials Hazardous decomposition products The product is stable and non-reactive under normal conditions of use, storage and transport. Material is stable under normal conditions. dangerous reaction known under conditions of normal use. Heat. Contact with incompatible materials. Strong oxidizing agents. hazardous decomposition products are known. 11. Toxicological information Information on likely routes of exposure Inhalation adverse effects due to inhalation are expected. Skin contact Eye contact Ingestion Symptoms related to the physical, chemical and toxicological characteristics Information on toxicological effects Acute toxicity Skin corrosion/irritation Serious eye damage/eye irritation Respiratory or skin sensitization Respiratory sensitization Skin sensitization Causes skin irritation. Causes serious eye irritation. Harmful if swallowed. Severe eye irritation. Symptoms may include stinging, tearing, redness, swelling, and blurred vision. Skin irritation. May cause redness and pain. Harmful if swallowed. Causes skin irritation. Causes serious eye irritation. t a respiratory sensitizer. This product is not expected to cause skin sensitization. 4 / 8
Germ cell mutagenicity Carcinogenicity IARC Monographs. Overall Evaluation of Carcinogenicity data available to indicate product or any components present at greater than 0.1% are mutagenic or genotoxic. This product is not considered to be a carcinogen by IARC, ACGIH, NTP, or OSHA. t listed. OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050) US. National Toxicology Program (NTP) Report on Carcinogens t listed. Reproductive toxicity Specific target organ toxicity - single exposure Specific target organ toxicity - repeated exposure Aspiration hazard This product is not expected to cause reproductive or developmental effects. t classified. t classified. t an aspiration hazard. 12. Ecological information Ecotoxicity Components Harmful to aquatic life with long lasting effects. Species N,n-diethyl-m-toluamide (DEET) (CAS 134-62-3) Aquatic Fish LC50 Fathead minnow (Pimephales promelas) Test Results 106-114 mg/l, 96 hours * Estimates for product may be based on additional component data not shown. Persistence and degradability Bioaccumulative potential data is available on the degradability of this product. Partition coefficient n-octanol / water (log Kow) N,n-diethyl-m-toluamide (DEET) 2.02 Mobility in soil Other adverse effects 13. Disposal considerations Disposal instructions Local disposal regulations Hazardous waste code Waste from residues / unused products Contaminated packaging data available. other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation potential, endocrine disruption, global warming potential) are expected from this component. Collect and reclaim or dispose in sealed containers at licensed waste disposal site. Contents under pressure. Do not puncture, incinerate or crush. Do not allow this material to drain into sewers/water supplies. Do not contaminate ponds, waterways or ditches with chemical or used container. Dispose of contents/container in accordance with local/regional/national/international regulations. Dispose in accordance with all applicable regulations. The waste code should be assigned in discussion between the user, the producer and the waste disposal company. Dispose of in accordance with local regulations. Empty containers or liners may retain some product residues. This material and its container must be disposed of in a safe manner (see: Disposal instructions). Since emptied containers may retain product residue, follow label warnings even after container is emptied. Empty containers should be taken to an approved waste handling site for recycling or disposal. Do not re-use empty containers. 14. Transport information DOT UN number UN1950 UN proper shipping name Aerosols, non-flammable, (each not exceeding 1 L capacity) Transport hazard class(es) Class Subsidiary risk - Label(s) Packing group t applicable. Special precautions for user 5 / 8
Packaging exceptions 306 Packaging non bulk ne Packaging bulk ne This product meets the exception requirements of section 173.306 as a limited quantity and may be shipped as a limited quantity. Until 12/31/2020, the "Consumer Commodity - ORM-D" marking may still be used in place of the new limited quantity diamond mark for packages of UN 1950 Aerosols. Limited quantities require the limited quantity diamond mark on cartons after 12/31/20 and may be used now in place of the "Consumer Commodity ORM-D" marking. IATA UN number UN1950 UN proper shipping name Aerosols, non-flammable Transport hazard class(es) Class Subsidiary risk - Label(s) Packing group t applicable. Environmental hazards. ERG Code 2L Special precautions for user Read safety instructions, SDS and emergency procedures before handling. Other information Passenger and cargo Allowed with restrictions. aircraft Cargo aircraft only Allowed with restrictions. Packaging Exceptions LTD QTY IMDG UN number UN1950 UN proper shipping name AEROSOLS Transport hazard class(es) Class Subsidiary risk - Label(s) Packing group t applicable. Environmental hazards Marine pollutant. EmS Special precautions for user Read safety instructions, SDS and emergency procedures before handling. Packaging Exceptions LTD QTY Transport in bulk according to t applicable. Annex II of MARPOL 73/78 and the IBC Code DOT 6 / 8
IATA; IMDG 15. Regulatory information US federal regulations This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication Standard, 29 CFR 1910.1200. TSCA Section 12(b) Export tification (40 CFR 707, Subpt. D) CERCLA Hazardous Substance List (40 CFR 302.4) t listed. SARA 304 Emergency release notification OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050) Superfund Amendments and Reauthorization Act of 1986 (SARA) Hazard categories Immediate Hazard - Yes Delayed Hazard - Fire Hazard - Pressure Hazard - Yes Reactivity Hazard - SARA 302 Extremely hazardous substance t listed. SARA 311/312 Hazardous chemical SARA 313 (TRI reporting) Other federal regulations Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130) Safe Drinking Water Act (SDWA) US state regulations US. California Controlled Substances. CA Department of Justice (California Health and Safety Code Section 11100) t listed. US. Massachusetts RTK - Substance List US. New Jersey Worker and Community Right-to-Know Act t listed. US. Pennsylvania Worker and Community Right-to-Know Law t listed. US. Rhode Island RTK US. California Proposition 65 California Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65): This material is not known to contain any chemicals currently listed as carcinogens or reproductive toxins. 7 / 8
International Inventories Country(s) or region Inventory name On inventory (yes/no)* Australia Australian Inventory of Chemical Substances (AICS) Canada Canada China Europe Europe Japan Korea New Zealand Philippines United States & Puerto Rico Domestic Substances List (DSL) n-domestic Substances List (NDSL) Inventory of Existing Chemical Substances in China (IECSC) European Inventory of Existing Commercial Chemical Substances (EINECS) European List of tified Chemical Substances (ELINCS) Inventory of Existing and New Chemical Substances (ENCS) Existing Chemicals List (ECL) New Zealand Inventory Philippine Inventory of Chemicals and Chemical Substances (PICCS) Toxic Substances Control Act (TSCA) Inventory *A "Yes" indicates that all components of this product comply with the inventory requirements administered by the governing country(s) A "" indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governing country(s). 16. Other information, including date of preparation or last revision Issue date Version # 01 Disclaimer 04-03-2018 The information provided in this Safety Data Sheet is correct to the best of our knowledge, information and belief at the date of its publication. The information given is designed only as a guidance for safe handling, use, processing, storage, transportation, disposal and release and is not to be considered a warranty or quality specification. The information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any process, unless specified in the text. Yes Yes 8 / 8