MUR12 Series Preferred Devices SWITCHMODE Power Rectifiers MUR15, MUR11, MUR115, MUR12, MUR13, MUR14, MUR16 The MUR12 series of SWITCHMODE power rectifiers are designed for use in switching power supplies, inverters and as free wheeling diodes. eatures Ultrafast 25, 5 and 75 Nanosecond Recovery Times 175 C Operating Junction Temperature ow orward Voltage ow eakage Current High Temperature Glass Passivated Junction Reverse Voltage to 6 V These are Pb ree Devices Mechanical Characteristics Case: Epoxy, Molded Weight:.4 gram (approximately) inish: All External Surfaces Corrosion Resistant and Terminal eads are Readily Solderable ead and Mounting Surface Temperature for Soldering Purposes: 22 C Max. for 1 Seconds, 1/16 from case Shipped in plastic bags, 1 per bag Available Tape and Reeled, 5 per reel, by adding a R suffix to the part number Polarity: Cathode Indicated by Polarity Band Marking: MUR15, MUR11, MUR115, MUR12, MUR13, MUR14, MUR16 UTRAAST RECTIIERS A, 5 V 6 V AXIA EAD CASE 59 1 PASTIC MARKING DIAGRAM MUR1xx MUR1 = Device Code xx = Specific Device Code ORDERING INORMATION See detailed ordering and shipping information in the package dimensions section on page 2 of this data sheet. *or additional information on our Pb ree strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SODERRM/D. Preferred devices are recommended choices for future use and best overall value. Semiconductor Components Industries, C, 24 April, 24 Rev. 7 1 Publication Order Number: MUR12/D
MUR12 Series MAXIMUM RATINGS Rating Symbol 15 11 115 12 13 14 16 Unit MUR Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage V RRM V RWM V R 5 1 15 2 3 4 6 V Average Rectified orward Current (Square Wave Mounting Method #3 Per Note 1) Nonrepetitive Peak Surge Current (Surge applied at rated load conditions, halfwave, single phase, 6 Hz) Operating Junction Temperature and Storage Temperature I (AV) @ T A = 13 C @ T A = 12 C A I SM 35 A T J, T stg 65 to +175 C Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. THERMA CHARACTERISTICS Maximum Thermal Resistance, Junction to Ambient R JA Note 1 C/W EECTRICA CHARACTERISTICS Maximum Instantaneous orward Voltage (Note 1) (i = Amp, T J = 15 C) (i = Amp, T J = ) v.71.875 5 1.25 V Maximum Instantaneous Reverse Current (Note 1) (Rated DC Voltage, T J = 15 C) (Rated DC Voltage, T J = ) i R 5 2. 15 A Maximum Reverse Recovery Time (I = A, di/dt = 5 A/ s) (I =.5 A, i R = A, I REC =.25 A) t rr 35 25 75 5 ns Maximum orward Recovery Time (I = A, di/dt = 1 A/ s, I REC to V) t fr 25 5 ns 1. Pulse Test: Pulse Width = 3 s, Duty Cycle 2.%. ORDERING INORMATION Device Marking Package Shipping MUR15 MUR15 Axial ead 1 Units/Bag MUR15R MUR15 Axial ead 5 Units/Tape & Reel MUR11 MUR11 Axial ead 1 Units/Bag MUR11R MUR11 Axial ead 5 Units/Tape & Reel MUR115 MUR115 Axial ead 1 Units/Bag MUR115R MUR115 Axial ead 5 Units/Tape & Reel MUR12 MUR12 Axial ead 1 Units/Bag MUR12R MUR12 Axial ead 5 Units/Tape & Reel MUR13 MUR13 Axial ead 1 Units/Bag MUR13R MUR13 Axial ead 5 Units/Tape & Reel MUR14 MUR14 Axial ead 1 Units/Bag MUR14R MUR14 Axial ead 5 Units/Tape & Reel MUR16 MUR16 Axial ead 1 Units/Bag MUR16R MUR16 Axial ead 5 Units/Tape & Reel or information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD811/D. 2
MUR12 Series, INSTANTANEOUS ORWARD CURRENT (AMPS), AVERAGE POWER DISSIPATION (WATTS) P (AV) I i 1 7. 3. 2..7.5.3.2.1.7.5.3.2.1.3.4.5.6.7.8.9 1.1 1.2 4. 3. 2. v, INSTANTANEOUS VOTAGE (VOTS) igure 1. Typical orward Voltage.5 1.5 2. 2.5 I (AV), AVERAGE ORWARD CURRENT (AMPS) MUR15, MUR11, MUR115, MUR12 1 C I (CAPACITIVE OAD) PK 2 I AV igure 4. Power Dissipation 1 1.3, REVERSE CURRENT ( A) I R, AVERAGE ORWARD CURRENT (AMPS) (AV) C, CAPACITANCE (p) 1 1.1.1.1 2 4 6 8 1 12 14 16 18 2 4. 3. 2. 5 5 3 2 1 7. 1 C igure 2. Typical Reverse Current* * The curves shown are typical for the highest voltage device in the voltage grouping. Typical reverse current for lower voltage selections can be estimated from these same curves if V R is sufficiently below rated V R. RATED V R R JA = 5 C/W 1 15 2 T A, AMBIENT TEMPERATURE ( C) igure 3. Current Derating (Mounting Method #3 Per Note 1) T J = 25 1 2 3 4 5 igure 5. Typical Capacitance 3
MUR12 Series MUR13, MUR14, MUR16 I, INSTANTANEOUS ORWARD CURRENT (AMPS), AVERAGE POWER DISSIPATION (WATTS) 1 7. i 3. 2..7.5.3.2.1.7.5.3.2.1.3.5.7.9 1.1 1.3 1.5 1.7 1.9 2.1 4. 3. 2. 1 C v, INSTANTANEOUS VOTAGE (VOTS) igure 6. Typical orward Voltage (CAPACITIVE OAD) I PK I AV 2 1 2.3, REVERSE CURRENT ( A) I R, AVERAGE ORWARD CURRENT (AMPS) (AV) C, CAPACITANCE (p) 4 1 4 1 4..4.1.4.1.4 4. 3. 2. 1 2 3 4 5 2 1 7. 3. 1 C 5 igure 7. Typical Reverse Current* 1 15 2 T A, AMBIENT TEMPERATURE ( C) igure 8. Current Derating (Mounting Method #3 Per Note 1) 6 * The curves shown are typical for the highest voltage device in the voltage grouping. Typical reverse current for lower voltage selections can be estimated from these same curves if V R is sufficiently below rated V R. RATED V R R JA = 5 C/W T J = 7 25 P (AV).5 1.5 2. 2.5 2. 1 2 3 4 5 I (AV), AVERAGE ORWARD CURRENT (AMPS) igure 9. Power Dissipation igure 1. Typical Capacitance 4
MUR12 Series NOTE 1. AMBIENT MOUNTING DATA Data shown for thermal resistance junction to ambient (R JA ) for the mountings shown is to be used as typical guideline values for preliminary engineering or in case the tie point temperature cannot be measured. TYPICA VAUES OR R JA IN STI AIR Mounting ead ength, Method 1/8 1/4 1/2 Units 1 2 3 52 65 72 R JA 67 8 87 5 C/W C/W C/W MOUNTING METHOD 1 É MOUNTING METHOD 2 Vector Pin Mounting MOUNTING METHOD 3 = 3/8 Board Ground Plane P.C. Board with 1 1/2 X 1 1/2 Copper Surface 5
MUR12 Series PACKAGE DIMENSIONS AXIA EAD CASE 59 1 ISSUE S K B D A NOTES: 1. DIMENSIONING AND TOERANCING PER ANSI Y14.5M, 1982. 2. CONTROING DIMENSION: INCH. 3. 59 4 OBSOETE, NEW STANDARD 59 9. 4. 59 3 OBSOETE, NEW STANDARD 59 1. 5. A RUES AND NOTES ASSOCIATED WITH JEDEC DO 41 OUTINE SHA APPY 6. POARITY DENOTED BY CATHODE BAND. 7. EAD DIAMETER NOT CONTROED WITHIN DIMENSION. INCHES MIIMETERS DIM MIN MAX MIN MAX A.161.25 4.1 5.2 B.79.16 2. 2.7 D.28.34.71.86.5 1.27 K 25.4 K SWITCHMODE is a trademark of Semiconductor Components Industries, C. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, C (SCIC). SCIC reserves the right to make changes without further notice to any products herein. SCIC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCIC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Typical parameters which may be provided in SCIC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including Typicals must be validated for each customer application by customer s technical experts. SCIC does not convey any license under its patent rights nor the rights of others. SCIC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCIC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCIC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCIC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCIC was negligent regarding the design or manufacture of the part. SCIC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBICATION ORDERING INORMATION ITERATURE UIMENT: iterature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 8217 USA Phone: 33 675 2175 or 8 344 386 Toll ree USA/Canada ax: 33 675 2176 or 8 344 3867 Toll ree USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 8 282 9855 Toll ree USA/Canada Japan: ON Semiconductor, Japan Customer ocus Center 2 9 1 Kamimeguro, Meguro ku, Tokyo, Japan 153 51 Phone: 81 3 5773 385 6 ON Semiconductor Website: Order iterature: http://www.onsemi.com/litorder or additional information, please contact your local Sales Representative. MUR12/D