2. HAZARDOUS INGREDIENTS Component % Hazard Data (EEC Classification) 2-Phenylphenol 1.18 Xi, N; R36/37/38/50

Size: px

Start display at page:

Download "2. HAZARDOUS INGREDIENTS Component % Hazard Data (EEC Classification) 2-Phenylphenol 1.18 Xi, N; R36/37/38/50"

Leslie Bennett
5 years ago
Views:

1 MATERIAL SAFETY DATA SHEET April 2003 Revision 01 The Wykamol Group, Units 1-3, Knowsley Road Industrial Estate, Knowsley Road,Haslingden, Lancs, BB4 4RX Tel: Fax: PRODUCT IDENTIFICATION Trade Name MCS1 Mouldclear Concentrate 5X Description Sterilising Solution 2. HAZARDOUS INGREDIENTS Component % Hazard Data (EEC Classification) 2-Phenylphenol 1.18 Xi, N; R36/37/38/50 Benzalkonium chloride 4.76 C, N; R21/ HAZARD IDENTIFICATION 6. HANDLING AND STORAGE Irritating to eyes and skin. Avoid contact with skin and eyes. If swallowed, seek medical advice immediately and show this sheet. Keep only in original container in a cool well ventilated place. Keep out of reach of children. Use only in well ventilated areas. Handling: Avoid skin contact. Avoid eye contact. Storage; to freeze. Store in original containers. Do not allow 4. EMERGENCY & FIRST AID 7. EXPOSURE CONTROL/PERSONAL PROTECTION Eyes: Wash copiously with water or eye wash for up to 15 minutes. If symptoms persist, seek medical attention. Skin: Remove contaminated clothing; wash thoroughly with soap and water. If irritation persists, obtain medical attention. Inhalation: Not applicable Ingestion: Do not induce vomiting, seek medical attention immediately. Beware of aspiration if vomiting occurs. Give plenty of water to drink. Engineering Measures: Provide adequate ventilation when using. Personal Protection: Impervious gloves, coveralls, hood. Eye Protection: Face shield or safety glasses/goggles recommended at all times. Respiratory Protection: - 5. FIRE FIGHTING MEASURES 8. SPILL OR LEAK PROCEDURES Extinguishing Media: Any Special Fire Fighting Procedures: None Unusual Fire Hazards: None Avoid spillage entering soil or drains/watercourses. Soak up with absorbent medium and wash down surfaces with water. Dispose of all waste in accordance with EPA Regulations.

2 MCS1 MOULDCLEAR CONCENTRATE 5X - PAGE 2 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance clear liquid Odour slight ph 8.0 Boiling Point C Melting Point n/a Flash Point n/a Flammability Non-flammable Autoignition Temp. - Oxidising Properties n/a Solubility in Water Fully miscible Relative Density 1.00 Vapour Pressure STABILITY AND REACTIVITY 12. ECOLOGICAL INFORMATION Conditions to avoid: No special conditions No adverse environmental effects foreseen. Marine pollutant (IMDG Code 1990). Not expected to bioaccumulate. Persistence: No specific data available. Materials to avoid: 13. WASTE DISPOSAL Hazardous decomposition products: Do not discharge into drains or watercourses. Dispose of through an authorised contractor to a licensed landfill site. 11. TOXICOLOGICAL INFORMATION 14. TRANSPORT INFORMATION Inhalation: Irritating to nose/throat/respiratory tract. UN/SI Number: 1263 Marine Pollutant Skin Contact: May cause soreness after prolonged contact. Skin Absorption: - Eye Contact: May cause severe irritation 15. REGULATORY INFORMATION IRRITANT IRRITATING TO EYES AND SKIN. Approved for use as directed under the Control of Pesticides Regulations 1986 (read the label before use). HSE No Ingestion: Small quantities unlikely to cause adverse effects. Acute Overexposure: - Chronic Overexposure: 16. OTHER INFORMATION Not applicable

3 MATERIAL SAFETY DATA SHEET April 2003 Revision 01 The Wykamol Group, Units 1-3, Knowsley Road Industrial Estate, Knowsley Road, HASLINGDEN, Lancs, BB4 4RX Tel: Fax: PRODUCT IDENTIFICATION Trade Name MCS3 Antimould Emulsion SILK Description Biocidal Paint 2. HAZARDOUS INGREDIENTS Component % Hazard Data (EEC Classification) 2-Octyl-2H-Isothialzol-3-One HAZARD IDENTIFICATION 6. HANDLING AND STORAGE No hazard classification Handling: No special requirements Storage: Store in dry conditions. Do not allow to freeze. Keep out of each of children. 4. EMERGENCY & FIRST AID 7. EXPOSURE CONTROL/PERSONAL PROTECTION Eyes: Rinse immediately with plenty of water (or eye wash) for at least 15 minutes. Seek medical attention if symptoms persist. Skin: Remove contaminated clothing. Wash affected area with soap and water. Launder contaminated clothing before re-use. Inhalation: Under normal conditions of use this product does not constitute an inhalation hazard. Ingestion: Administer pint of water and seek medical attention. If symptoms attributable to this product occur consult a doctor. Never administer anything to an unconscious person. Engineering Measures: Ensure adequate ventilation during and after use. Personal Protection: Coveralls, boots, synthetic rubber/pvc gloves or gauntlets. Eye Protection: Wear suitable eye protection. Respiratory Protection: If spraying wear suitable respiratory protection (i.e respirator fitted with a P2- P3 type cartridge, or a disposable particulate mask). 5. FIRE FIGHTING MEASURES 8. SPILL OR LEAK PROCEDURES Extinguishing Media: Any Special Fire Fighting Procedures: None Unusual Fire Hazards: None Shut off or remove source of leak. Absorb spillage with dry sand, earth, vermiculate or similar. Place into a suitable container (metal or plastic) to await disposal. Remaining or smaller spillages may e flushed with water. Do not allow waste or run off to contaminate ponds, waterways or ditches.

4 MCS3 ANTIMOULD EMULSION - SILK Material Safety Data Sheet - PAGE 2 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance Emulsion Paint Odour Slight ph 6-8 Boiling Point > 100 C Melting Point N/A Flash Point N/A Flammability Non-flammable Autoignition Temp. N/A Oxidising Properties None Solubility in Water Fully miscible Relative Density Ca 1.34 Vapour Pressure STABILITY AND REACTIVITY 12. ECOLOGICAL INFORMATION Conditions to avoid: Under normal conditions of use and storage this product is stable. Materials to avoid:. No adverse environmental effects foreseen. Marine pollutant (IMDG Code 1990). No expected bioaccumalate. Persistence: Specific data available. 13. WASTE DISPOSAL Hazardous decomposition products: Dispose of liquid waste in accordance with Enviromental Protection Act 1999, preferably by landfill at a site authorised and licensed waste disposal contractor. Clean and decontaminated containers may be disposed of as inert industrial or domestic refuse. The Duty of Care Waste Transfer form should specify: Pesticide product. 11. TOXICOLOGICAL INFORMATION 14. TRANSPORT INFORMATION Inhalation: Inhalation of spray mist may result in some irritation to the respiratory system by way of a persistent cough. Skin Contact: Prolonged exposure may cause dryness and cracking. Persons with a history of skin complaints and allergies should avoid prolonged contact. No special regulations apply. Vehicles should provide secure storage area to contain spillage in the event of an accident. Skin Absorption: exposure. Possible irritation at site of 15. REGULATORY INFORMATION Eye Contact: May cause discomfort/redness if contact with concentrate prolonged. Use only in accordance with Statutory Conditions given under the Control of Pesticides Regulations 1986 for Amateur and Professional use as directed. HSE Approval No Ingestion: May cause nausea if swallowed. Acute Overexposure: - Chronic Overexposure: Frequent contact may cause skin condition to deteriorate. 16. OTHER INFORMATION The COSHH Regulations 1999 may apply to this product if used at work.

5 MATERIAL SAFETY DATA SHEET April 2003 Revision 01 The Wykamol Group, Units 1-3, Knowsley Road Industrial Estate, Knowsley Road, HASLINGDEN, Lancs, BB4 4RX Tel: Fax: PRODUCT IDENTIFICATION Trade Name MCS3 Antimould Emulsion MATT Description Biocidal Paint 2. HAZARDOUS INGREDIENTS Component % Hazard Data (EEC Classification) 2-Octyl-2H-Isothialzol-3-One HAZARD IDENTIFICATION 6. HANDLING AND STORAGE No hazard classification Handling: No special requirements Storage: Store in dry conditions. Do not allow to freeze. Keep out of each of children. 4. EMERGENCY & FIRST AID 7. EXPOSURE CONTROL/PERSONAL PROTECTION Eyes: Rinse immediately with plenty of water (or eye wash) for at least 15 minutes. Seek medical attention if symptoms persist. Skin: Remove contaminated clothing. Wash affected area with soap and water. Launder contaminated clothing before re-use. Inhalation: Under normal conditions of use this product does not constitute an inhalation hazard. Ingestion: Administer pint of water and seek medical attention. If symptoms attributable to this product occur consult a doctor. Never administer anything to an unconscious person. Engineering Measures: Ensure adequate ventilation during and after use. Personal Protection: Coveralls, boots, synthetic rubber/pvc gloves or gauntlets. Eye Protection: Wear suitable eye protection. Respiratory Protection: If spraying wear suitable respiratory protection (i.e respirator fitted with a P2- P3 type cartridge, or a disposable particulate mask). 5. FIRE FIGHTING MEASURES 8. SPILL OR LEAK PROCEDURES Extinguishing Media: Any Special Fire Fighting Procedures: None Unusual Fire Hazards: None Shut off or remove source of leak. Absorb spillage with dry sand, earth, vermiculate or similar. Place into a suitable container (metal or plastic) to await disposal. Remaining or smaller spillages may e flushed with water. Do not allow waste or run off to contaminate ponds, waterways or ditches.

6 MCS3 ANTIMOULD EMULSION - MATT Material Safety Data Sheet - PAGE 2 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance Emulsion Paint Odour Slight ph 6-8 Boiling Point > 100 C Melting Point N/A Flash Point N/A Flammability Non-flammable Autoignition Temp. N/A Oxidising Properties None Solubility in Water Fully miscible Relative Density Ca 1.34 Vapour Pressure STABILITY AND REACTIVITY 12. ECOLOGICAL INFORMATION Conditions to avoid: Under normal conditions of use and storage this product is stable. Materials to avoid:. No adverse environmental effects foreseen. Marine pollutant (IMDG Code 1990). No expected bioaccumalate. Persistence: Specific data available. 13. WASTE DISPOSAL Hazardous decomposition products: Dispose of liquid waste in accordance with Enviromental Protection Act 1999, preferably by landfill at a site authorised and licensed waste disposal contractor. Clean and decontaminated containers may be disposed of as inert industrial or domestic refuse. The Duty of Care Waste Transfer form should specify: Pesticide product. 11. TOXICOLOGICAL INFORMATION 14. TRANSPORT INFORMATION Inhalation: Inhalation of spray mist may result in some irritation to the respiratory system by way of a persistent cough. Skin Contact: Prolonged exposure may cause dryness and cracking. Persons with a history of skin complaints and allergies should avoid prolonged contact. No special regulations apply. Vehicles should provide secure storage area to contain spillage in the event of an accident. Skin Absorption: exposure. Possible irritation at site of 15. REGULATORY INFORMATION Eye Contact: May cause discomfort/redness if contact with concentrate prolonged. Use only in accordance with Statutory Conditions given under the Control of Pesticides Regulations 1986 for Amateur and Professional use as directed. HSE Approval No Ingestion: May cause nausea if swallowed. Acute Overexposure: - Chronic Overexposure: Frequent contact may cause skin condition to deteriorate. 16. OTHER INFORMATION The COSHH Regulations 1999 may apply to this product if used at work.

7 MATERIAL SAFETY DATA SHEET April 2003 Revision 01 The Wykamol Group, Units 1-3, Knowsley Road Industrial Estate, Knowsley Road, HASLINGDEN, Lancs, BB4 4RX Tel: Fax: PRODUCT IDENTIFICATION Trade Name MCS3 Antimould Emulsion SILK Description Biocidal Paint 2. HAZARDOUS INGREDIENTS Component % Hazard Data (EEC Classification) 2-Octyl-2H-Isothialzol-3-One HAZARD IDENTIFICATION 6. HANDLING AND STORAGE No hazard classification Handling: No special requirements Storage: Store in dry conditions. Do not allow to freeze. Keep out of each of children. 4. EMERGENCY & FIRST AID 7. EXPOSURE CONTROL/PERSONAL PROTECTION Eyes: Rinse immediately with plenty of water (or eye wash) for at least 15 minutes. Seek medical attention if symptoms persist. Skin: Remove contaminated clothing. Wash affected area with soap and water. Launder contaminated clothing before re-use. Inhalation: Under normal conditions of use this product does not constitute an inhalation hazard. Ingestion: Administer pint of water and seek medical attention. If symptoms attributable to this product occur consult a doctor. Never administer anything to an unconscious person. Engineering Measures: Ensure adequate ventilation during and after use. Personal Protection: Coveralls, boots, synthetic rubber/pvc gloves or gauntlets. Eye Protection: Wear suitable eye protection. Respiratory Protection: If spraying wear suitable respiratory protection (i.e respirator fitted with a P2- P3 type cartridge, or a disposable particulate mask). 5. FIRE FIGHTING MEASURES 8. SPILL OR LEAK PROCEDURES Extinguishing Media: Any Special Fire Fighting Procedures: None Unusual Fire Hazards: None Shut off or remove source of leak. Absorb spillage with dry sand, earth, vermiculate or similar. Place into a suitable container (metal or plastic) to await disposal. Remaining or smaller spillages may e flushed with water. Do not allow waste or run off to contaminate ponds, waterways or ditches.

8 MCS3 ANTIMOULD EMULSION - SILK Material Safety Data Sheet - PAGE 2 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance Emulsion Paint Odour Slight ph 6-8 Boiling Point > 100 C Melting Point N/A Flash Point N/A Flammability Non-flammable Autoignition Temp. N/A Oxidising Properties None Solubility in Water Fully miscible Relative Density Ca 1.34 Vapour Pressure STABILITY AND REACTIVITY 12. ECOLOGICAL INFORMATION Conditions to avoid: Under normal conditions of use and storage this product is stable. Materials to avoid:. No adverse environmental effects foreseen. Marine pollutant (IMDG Code 1990). No expected bioaccumalate. Persistence: Specific data available. 13. WASTE DISPOSAL Hazardous decomposition products: Dispose of liquid waste in accordance with Enviromental Protection Act 1999, preferably by landfill at a site authorised and licensed waste disposal contractor. Clean and decontaminated containers may be disposed of as inert industrial or domestic refuse. The Duty of Care Waste Transfer form should specify: Pesticide product. 11. TOXICOLOGICAL INFORMATION 14. TRANSPORT INFORMATION Inhalation: Inhalation of spray mist may result in some irritation to the respiratory system by way of a persistent cough. Skin Contact: Prolonged exposure may cause dryness and cracking. Persons with a history of skin complaints and allergies should avoid prolonged contact. No special regulations apply. Vehicles should provide secure storage area to contain spillage in the event of an accident. Skin Absorption: exposure. Possible irritation at site of 15. REGULATORY INFORMATION Eye Contact: May cause discomfort/redness if contact with concentrate prolonged. Use only in accordance with Statutory Conditions given under the Control of Pesticides Regulations 1986 for Amateur and Professional use as directed. HSE Approval No Ingestion: May cause nausea if swallowed. Acute Overexposure: - Chronic Overexposure: Frequent contact may cause skin condition to deteriorate. 16. OTHER INFORMATION The COSHH Regulations 1999 may apply to this product if used at work.

Dulux New Zealand, a division of DuluxGroup (New Zealand) Pty Ltd ABN Co

Dulux New Zealand, a division of DuluxGroup (New Zealand) Pty Ltd ABN Co 1. IDENTIFICATION OF THE MATERIAL AND SUPPLIER Product Name: Recommended Use: 587-LINE DULUX PROFESSIONAL INTERIOR LOW SHEEN ACRYLIC Surface coating. Applied by brush, roller or spray. Supplier: Dulux