SAFETY DATA SHEET SILICONE LUBRICANT GEL

Transcription

1 Revision Date: 31/03/17 SDS NO: / 6 SAFETY DATA SHEET SILICONE LUBRICANT GEL SL50 SECTION 1: IDENTIFICATION OF THE SUBSTANCE/PREPERATION AND OF THE COMPANY/UNDERTAKING 1.1 PRODUCT IDENTIFIER PRODUCT NAME PRODUCT No. SILICONE LUBRICANT GEL SL RELEVANT IDENTIFIED USES OF THE SUBSTANCE OR MIXTURE AND USES ADVISED AGAINST APPLICATION OF THE SUBSTANCE / PREPERATION LUBRICANT EMULSION 1.3 DETAILS OF THE SUPPLIER SUPPLIER FloPlast LTD MANUFACTURED FOR CEDESA Ltd. CASTLE ROAD FloPlast LIMITED BY: CHARTER-LEA BUILDING EUROLINK BUSINESS PARK ICKNEIL WAY SITTINGBOURNE LETCHWORTH GARDEN CITY KENT SG6 1WT ME10 3FP technical@floplast.co.uk EMERGENCY TELE: (08:00HRS 17:30HRS) SECTION 2: HAZARD IDENTIFICATION CLASIFICATION OF SUBSTANCES Non-Flammable. Non-Hazardous. SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS 3.1 PRODUCT DESCRIPTION Silicone lubricant gel. SECTION 4: FIRST AID MEASURES 4.1 DESCRIPTION OF FIRST AID MEASURES General information: After inhalation: After skin contact: After eye contact: After inhalation: No special measures required. Move the exposed person to fresh air at once. Wash skin with soap and water. Immediately flush with plenty of water for up to 15 minutes. Remove any contact lenses and open eyes wide apart. Move the exposed person to fresh air at once. 4.2 INFORMATION FOR DOCTOR: Most important symptoms and effects, both acute and delayed

2 Revision Date: 31/03/17 SDS NO: / Indication of any immediate medical attention and special treatment needed SECTION 5: FIRE FIGHTING MEASURES 5.1 EXTINGUISHING MEDIA The product is non-combustible. Use fire-extinguishing media appropriate for surrounding materials. 5.2 SPECIAL HAZARDS ARISING FROM THE SUBSTANCE OR MIXTURE Avoid breathing fire vapours. Keep run-off water out of sewers and water sources. Dike for water control. If risk of water pollution occurs, notify appropriate authorities. 5.3 ADVICE FOR FIREFIGHTERS Thermal decomposition or combustion may liberate carbon oxides and other toxic gases or vapours Protective equipment Self contained breathing apparatus and full protective clothing must be worn in case of fire. SECTION 6: ACCIDENTAL RELEASE MEASURES 6.1 PERSONAL PRECUATIONS, PROTECTIVE EQUIPMENT AND EMERGANCY PROCEDURES Wear protective clothing as described in Section 8 of this safety data sheet. Avoid contact with eyes. Avoid forming spray mists/aerosols. In case of spills, beware of slippery floors and surfaces. 6.2 ENVIRONMENTAL PRECAUTIONS Do not discharge into drains, water courses or onto the ground. Avoid discharge to the aquatic environment. 6.3 METHODS AND MATERIAL FOR CONTAINMENT AND CLEANING UP Wear necessary protective equipment. Remove sources of ignition. Absorb spillage with non-combustible, absorbent material. Collect spillage in containers, seal securely and deliver for disposal according to local regulations. Runoff or release to sewer, waterway or ground is forbidden. Inform Authorities if large amounts are involved. 6.4 REFERENCE TO OTHER SECTIONS See Section 7 for information on safe handling. See Section 8 for information on personal protection equipment. See Section 13 for disposal information. SECTION 7: HANDLING AND STORAGE 7.1 PRECAUTIONS OF SAFE HANDLING Avoid contact with eyes. Avoid eating, drinking and smoking when using the product. Observe good industrial hygiene practices. 7.2 CONDITIONS FOR SAFE STORAGE, INCLUDING ANY INCOMPTABILITIES Store in tightly closed original container in a dry, cool and well-ventilated place. Avoid frost. Keep separate from food, feedstuffs, fertilisers and other sensitive material. 7.3 REQUIREMENTS TO BE MET BY STOREROOMS AND RECEPTACLES Storage Class: Chemical storage. MIN. STORAGE TEMP ( C): 5 MAX. STORAGE TEMP ( C): INFORMATION ABOUT STORAGE IN ONE COMMON STORAGE FACILITY Not required.

3 Revision Date: 31/03/17 SDS NO: / FURTHER INFORMATION ABOUT STORAGE CONDITIONS None 7.6 SPECIFIC END USE(S) SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION 8.1 CONTROL PARAMETERS Ingredients with limit values that require monitoring at the workplace; The product does not contain any relevant quantities of materials with critical values that have to be monitored at the workplace Additional information: Provide adequate general and local exhaust ventilation. 8.2 PROTECTIVE EQUIPMENT General protective and hygienic measures: Wash at the end of each work shift and before eating, smoking and using the toilet. Wash hands after contact. Wash contaminated clothing before reuse. When using do not eat, drink or smoke. The usual precautionary measures are to be adhered to when handling chemicals Respiratory protection: No specific recommendation made, but respiratory protection may still be required under exceptional circumstances when excessive air contamination exists. Seek advice from supervisor on the companies' respiratory protection standards Protection of hands: Protective gloves For prolonged or repeated skin contact use suitable protective gloves. Material of gloves Neoprene or PVC gloves are recommended Eye protection: Tightly sealed goggles Wear approved chemical safety goggles where eye exposure is reasonably probable. 8.3 OTHER PRETECTION Provide eyewash station. Wear appropriate clothing to prevent repeated or prolonged skin contact.

4 Revision Date: 31/03/17 SDS NO: / 6 SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES 9.1 INFORMATION ON BASIC PHYSICAL AND CHEMICAL PROPERTIES Appearance: Form: Colour: Odour: Solubility: Paste Cream No characteristic odour. Miscible with water. Relative Density: ph-value, conc.solution: Flash point: > 100 Viscosity: 9.2 OTHER INFORMATION SECTION 10: STABILITY AND REACTIVITY 10.1 REACTIVITY 10.2 CHEMICAL STABILITY > 6000 cps Stable under normal temperature conditions and recommended use THERMAL DECOMPOSITION/CONDITIONS TO BE AVOIDED 10.4 POSSIBILITY OF HAZARDOUS REACTIONS 10.5 CONDITIONS TO AVOID Avoid excessive heat for prolonged periods of time. Avoid heat, flames and other sources of ignition. Avoid frost INCOMPATIBLE MATERIALS No incompatible groups noted HAZARDDOUS DECOMPOSITION PRODUCTS None under normal conditions. Thermal decomposition or combustion may liberate carbon oxides and other toxic gases or vapours. SECTION 11: TOXICOLOGICAL INFORMATION 11.1 ACUTE TOXICITY 11.2 PRIMARY IRRITANT EFFECT on the skin: May cause deflating of the skin, but is not an irritant. Repeated exposure may cause skin dryness or cracking on the eye: # Spray and vapour in the eyes may cause irritation and smarting. May cause temporary eye irritation on inhalation: Spray mists may cause respiratory tract irritation. In case of inhalation of spray mist: Move person into fresh air and keep at rest on ingestion: May cause discomfort if swallowed. May irritate and cause stomach pain, vomiting and diarrhoea. No harmful effects expected in amounts likely to be ingested by accident.

5 Revision Date: 31/03/17 SDS NO: / SENSITIZATION No sensitizing effects known. SECTION 12: ECOLOGICAL INFORMATION 12.1 ECOTOXICITY The product components are not classified as environmentally hazardous. However, this does not exclude the possibility that large or frequent spills can have a harmful or damaging effect on the environment ACQUATIC TOXICITY 12.3 PERSISTENCE AND DEGRADABILITY 12.4 BEHAVIOUR IN ENVIRONMENTAL SYSTEMS 12.5 BIOACCUMULATIVE POTENTIAL 12.6 MOBILITY IN SOIL 12.7 ADDITIONAL ECOLOGICAL INFORMATIONS GENERAL NOTES WATER HAZARD CLASSIFICATION: WGK RESULTS OF PBT and vpvb ASSESSMENT OTHER ADVERSE EFFECTS SECTION 13: DISPOSAL CONSIDERATIONS 13.1 WASTE TREATMENT METHODS Recommendations Waste to be treated as controlled waste. Disposal to licensed waste disposal site in accordance with local Waste Disposal Authority. When handling waste, consideration should be made to the safety precautions applying to handling of the product. Environmental manager must be informed of all major spillages. Dispose of waste and residues in accordance with local authority requirements. Do not allow runoff to sewer, waterway or ground. Smaller quantities can be disposed of with household waste UNCLEANED PACKAGING Recommendation Waste to be treated as controlled waste. Disposal to licensed waste disposal site in accordance with local Waste Disposal Authority. When handling waste, consideration should be made to the safety precautions applying to handling of the product. Environmental manager must be informed of all major spillages. Dispose of waste and residues in accordance with local authority requirements. Do not allow runoff to sewer, waterway or ground. Smaller quantities can be disposed of with household waste. SECTION 14: TRANSPORT INFORMATION The product is not covered by international regulation on the transport of dangerous goods (IMDG, IATA, ADR/RID).

6 Revision Date: 31/03/17 SDS NO: / 6 SECTION 15: REGULATORY INFORMATION 15.1 SAFETY, HEALTH AND ENVIRONMENTAL REGULATIONS/LEGISLATION SPECIFIC FOR THE SUBSTANCE OR MIXTURE 15.2 LABELLING ACCORDING TO EU REGULATIONS 15.3 CODE LETTER AND HAZARD DESIGNATION OF PRODUCT 15.4 HAZARD PHRASES 15.5 PRECUATIONARY PHRASES 15.6 UK REGULATORY REFERENCES 15.7 EU DIRECTIVES CLP Regulations. Regulation (EC) No 1907/2006 concerning the Registration, Evaluation, Authorisation and Restriction of Chemicals (REACH) STATUTORY INSTRUMENTS 15.9 APPROVED CODE OF PRACTICE WATERHAZARD CLASS Water hazard classification: WGK CHEMICAL SAFETY ASSESSMENT A Chemical Safety Assessment has not been carried out APPROVED CODE OF PRACTICE Safety Data Sheets for Substances and Preparations. Classification and Labelling of Substances and Preparations Dangerous for Supply GUIDANCE NOTES Workplace Exposure Limits EH40. SECTION 16: OTHER INFORMATION This product should be used as directed by BISON INTERNATIONAL BV. For further information consult the product data sheet or contact FloPlast s Technical Department. The safety data sheet has been complied using current information supplied by BISON INTERNATIONAL BV and the distributors of their raw materials. Issued By Department Neil Harrison Revision Date 31 st March 2017 Revision 6 Hazard Phrases in Full NC Quality/Environmental/Health and Safety Not classified.