MATERIAL SAFETY DATA SHEET

Transcription

1 MATERIAL SAFETY DATA SHEET SECTION 1 CHEMICAL PRODUCT AND COMPANY IDENTIFICATION PRODUCT NAME: BUEHLER ZIRMET DISCS, ZIRMET-METSPLICE BELTS IDENTIFICATION NUMBER: ZIRMET DISCS: (060 thru 220)-25 ZIRMET-METSPLICE BELTS: (060 thru 220)-25 PRODUCT USE/CLASS: Abrasive SUPPLIER: BUEHLER, a division of Illinois Tool Works Inc. 41 WAUKEGAN ROAD LAKE BLUFF, IL EMERGENCY: INFORMATION: PREPARER: Technical Department, PREPARE DATE: 4/03/2012, 03 April 2012 SECTION 2 COMPOSITION/INFORMATION ON INGREDIENTS ITEM CHEMICAL NAME CAS NUMBER WT/WT% 01 Aluminum oxide Zirconium Inorganic Fluorides NONE - MIX ITEM ACGIH TLV- ACGIH TLV- OSHA PEL-TWA OSHA PEL COMPANY TLV- SKIN TWA STEL CEILING TWA mg/m 3 N.E. 15 mg/m 3 N.E. N.E. NO 02 5 mg/m 3 N.E. 5 mg/m 3 N.E. N.E. NO mg/m 3 N.E. 2.5mg/m 3 N.E. N.E. NO (SEE SECTION 16 FOR ABBREVIATION LEGEND) Page 1 of 7

2 SECTION 3 HAZARDS IDENTIFICATION EMERGENCY OVERVIEW: When determining the degree of health hazards, the material being abraded must be considered. ACUTE EFFECTS EYE CONTACT: Mechanical eye irritation: Signs/symptoms may include pain, redness, tearing and corneal abrasion. Dust created by grinding, sanding, or machining may cause eye irritation. Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision. ACUTE EFFECTS - SKIN CONTACT: Mechanical Skin irritation: Signs/symptoms may include abrasion, redness, pain, and itching ACUTE EFFECTS INHALATION: Dust from grinding, sanding or machining may cause irritation of the respiratory system. Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and throat pain. ACUTE EFFECTS - INGESTION: Physical Blockage: Signs/symptoms may include cramping, abdominal pain, and constipation. CHRONIC OVEREXPOSURE EFFECTS: Prolonged or repeated exposure may cause: Pneumoconiosis: Sign/symptoms may include persistent cough, breathlessness, chest pain, increased amounts of sputum, and changes in lung function tests OTHER INFORMATION: Not Applicable. PRIMARY ROUTE(S) OF ENTRY: INHALATION SECTION 4 FIRST AID MEASURES EYE CONTACT: Immediately flush eyes with plenty of water. Get medical attention if irritation persists. SKIN CONTACT: Wash with soap and water. Get medical attention if irritation develops or persists. INHALATION: No specific treatment is necessary since this material is not likely to be hazardous by inhalation. If symptoms occur, remove to fresh air. Medical personnel may administer oxygen if breathing is difficult. Seek medical attention if symptoms persist. INGESTION: If swallowed, do NOT induce vomiting. Give victim a glass of water or milk. Call a physician or poison control center immediately. Never give anything by mouth to an unconscious person. NOTES TO PHYSICIAN: Treat symptomatically. Page 2 of 7

3 SECTION 5 FIRE FIGHTING MEASURES FLASH POINT: N.A. LOWER EXPLOSIVE LIMIT: N.A. UPPER EXPLOSIVE LIMIT: N.A. AUTOIGNITION TEMPERATURE: N.A. EXTINGUISHING MEDIA: CO2, Foam, Dry Chemical, Water Spray UNUSUAL FIRE AND EXPLOSION HAZARDS: Not Applicable. SPECIAL FIREFIGHTING PROCEDURES: Wear a NIOSH approved positive pressure self-contained breathing apparatus with full protective clothing. Do not release runoff from fire control methods to sewers or waterways. SECTION 6 ACCIDENTAL RELEASE MEASURES STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Reclaim clean material. Contaminated material should be swept or shoveled into appropriate waste container and disposed of in accordance with applicable federal, state and local regulations. SECTION 7 HANDLING AND STORAGE HANDLING: For industrial or professional use only. Avoid breathing of dust created by sanding, grinding or machining. STORAGE: Store in a cool place. Page 3 of 7

4 SECTION 8 EXPOSURE CONTROLS/PERSONAL PROTECTION ENGINEERING CONTROLS: Provide appropriate local exhaust ventilation for sanding, grinding or machining. Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below Occupational Exposure Limits and/or control dust, fume, or airborne particles. If ventilation is not adequate, use respiratory protection equipment. RESPIRATORY PROTECTION: Avoid breathing of dust created by sanding, grinding or machining. Assess exposure concentrations of all materials involved in the work process. Consider material being abraded when determining the appropriate respiratory protection. Select and use appropriate respirators to prevent inhalation overexposure. Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with OSHA regulations: Half-face piece or full-face air-purifying respirator with N95 particulate filters. Select and use respiratory protection to prevent an inhalation exposure based on the results of an exposure assessment. SKIN PROTECTION: Avoid skin contact. Wear appropriate gloves to minimize risk of injury to skin from contact with dust or physical abrasion from grinding or sanding. EYE PROTECTION: Eye protection (i.e., safety glasses, safety goggles and/or face shield) should be determined based on conditions of use. OTHER PROTECTIVE EQUIPMENT: Cloth or synthetic gloves. HYGIENIC PRACTICES: Follow good general industrial safety practices during use. SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES BOILING RANGE: N.A. VAPOR DENSITY: N.A. ODOR: None ODOR THRESHOLD: N.A. APPEARANCE: Solid disk or belt EVAPORATION RATE: N.A. SOLUBILITY IN H 2 O: Insoluble FREEZE POINT: N.A. SPECIFIC GRAVITY: > 2 VAPOR PRESSURE: N.A. 0.0%: N.A. PHYSICAL STATE: N.A. VISCOSITY: N.A. COEFFICIENT OF WATER/OIL DISTRIBUTION: N.A. (SEE SECTION 16 FOR ABBREVIATION LEGEND) Page 4 of 7

5 SECTION 10 STABILITY AND REACTIVITY CONDITIONS TO AVOID: None known INCOMPATIBILITY: Strong bases or oxidants. Organic peroxides. HAZARDOUS DECOMPOSITION PRODUCTS: Carbon monoxide - During Combustion, Carbon dioxide - During Combustion, HAZARDOUS POLYMERIZATION: Hazardous polymerization will not occur. STABILITY: This product is stable under normal storage conditions. SECTION 11 TOXICOLOGICAL PROPERTIES No product or component toxicological information is available. SECTION 12 ECOLOGICAL INFORMATION The environmental properties of this product present a low environmental hazard. SECTION 13 DISPOSAL CONSIDERATIONS DISPOSAL METHOD: If product becomes contaminated, follow disposal instructions for contaminant. Dispose of in accordance with federal, state and local regulations. Page 5 of 7

6 SECTION 14 TRANSPORTATION INFORMATION DOT PROPER SHIPPING NAME: Not regulated for transport DOT TECHNICAL NAME: N.A. DOT HAZARD CLASS: N.A. DOT UN/NA CLASS: N.A. HAZARD SUBCLASS: N.A. PACKAGING GROUP: N.A. RESP. GUIDE PAGE: INTERNATIONAL SHIPPING NAME: Not regulated for transport INTERNATIONAL ID NUMBER: N.A. IMDG CLASS (1, 2 ): N.A. IMDG EMS: N.A. IMDG PAGE NUMBER: N.A. IATA CLASS (1, 2 ): N.A. SECTION 15 REGULATORY INFORMATION OSHA: Hazardous by definition of Hazard Communication Standard (29 CFR ). CERCLA SARA HAZARD CATEGORY: THIS PRODUCT HAS BEEN REVIEWED, AND IS CONSIDERED, UNDER APPLICABLE DEFINITIONS, TO MEET THE FOLLOWING CATEGORIES: NONE SARA SECTION 313: THIS PRODUCT CONTAINS THE FOLLOWING SUBSTANCES SUBJECT TO THE REPORTING REQUIREMENTS OF SECTION 313 AND 40 CFR PART 372: CHEMICAL NAME CAS NUMBER No SARA Section 313 components exist in this product. TOXIC SUBSTANCE CONTROL ACT: THE CHEMICAL SUBSTANCES IN THIS PRODUCT ARE ON THE TSCA SECTION 8 INVENTORY. THIS PRODUCT CONTAINS THE FOLLOWING CHEMICAL SUBSTANCES SUBJECT TO THE REPORTING REQUIREMENTS OF TSCA 12(B) IF EXPORTED FROM THE UNITED STATES: CHEMICAL NAME CAS NUMBER No compounds found NEW JERSEY RIGHT-TO-KNOW: THE FOLLOWING MATERIALS ARE NON-HAZARDOUS, BUT ARE AMONG THE TOP 5 COMPONENTS IN THIS PRODUCT: Cloth or paper backing, binder system PENNSYLVANIA RIGHT-TO-KNOW: THE FOLLOWING NON-HAZARDOUS INGREDIENTS ARE PRESENT IN THE PRODUCT AT GREATER THAN 3%: Cloth or paper backing, binder system CALIFORNIA PROPOSTION 65: No Proposition 65 chemicals known to exist in this product. Page 6 of 7

7 SECTION 15 REGULATORY INFORMATION CANADIAN WHMIS: THIS MSDS HAS BEEN PREPARED IN COMPLIANCE WITH CONTROLLED PRODUCT REGULATIONS EXCEPT FOR USE OF THE 16 HEADINGS. CANADIAN WHMIS CLASS: NONE COMPONENT RCRA CLASSIFICATIONS: Not regulated COMPONENT RCRA CODES: Not Applicable. CERCLA RQ VALUE (MINIMUM): None known SECTION 16 OTHER INFORMATION HMIS RATINGS HEALTH: 1 FLAMMABILITY: 0 REACTIVITY: 0 PREVIOUS MSDS REVISION DATE: 03/23/2009, 23 March 2009 REASON FOR REVISION: Administrative change for new format. Revised section(s) 1, 3, 6, 8, & 16, VOLATILE ORGANIC COMPOUNDS: 0 grams/ltr LEGEND: N.A. NO INFORMATION N.E. NOT ESTABLISHED N.D. NOT DETERMINED ABBREVIATIONS: ACGIH = AMERICAN CONFERENCE OF GOVERNMENTAL INDUSTRIAL HYGIENISTS; OSHA = OCCUPATIONAL HEALTH AND SAFETY ADMINISTRATION; TLV-TWA = THRESHOLD LIMIT VALUE TIME WEIGHTED AVERAGE (8 HOURS); STEL = SHORT-TERM EXPOSURE LIMIT (15 MINUTES); C = CEILING VALUE; PEL = PERMISSIBLE EXPOSURE LIMIT DISCLAIMER: TO THE BEST OF OUR KNOWLEDGE, THE INFORMATION CONTAINED IN THIS MSDS IS ACCURATE OR IS OBTAINED FROM SOURCES BELIEVED TO BE ACCURATE. HOWEVER, NO LIABILITY, EXPRESSED OR IMPLIED, IS ASSUMED FOR THE ACCURACY OR COMPLETENESS OF THE INFORMATION CONTAINED HEREIN. BUYER ASSUMES LIABILITY IN ITS USE OF THE MATERIAL. Page 7 of 7