Chemical characterisation Preparation contains isoparaffin hydrocarbons and synthetic esters

Transcription

1 1 Identification of the Substance / Preparation and Company Trade name Use of the substance / preparation Non-water-miscible metalworking lubricant Page 1 of 6 Company name Information on the substance / preparation Product safety Phone: +49 (0) *2 Composition / Information on Ingredients Chemical characterisation Preparation contains isoparaffin hydrocarbons and synthetic esters Dangerous ingredients Name CAS-No. Concentration Symbol Special risks. Isoalkanes (C9 C12) % Xn *3 Hazards Identification Hazards for human beings and the environment Can have fairly long-term harmful effects in waters. 4 First-Aid Measures

2 Page 2 of 6 Skin contact Remove contaminated clothing immediately and wash affected parts of the body with soap and water. Eye contact Rinse the eye thoroughly without delay for 15 minutes holding the eyelid open under running water and seek medical advice. Inhalation Take the patient into the fresh air and keep him calm. Ingestion Do not induce vomiting. Get medical attention. Rinse out the mouth with water. 5 Fire-Fighting Measures Suitable fire fighting agents Foam, CO 2, dry extinguishing agents, water mist Unsuitable fire fighting agents for safety reasons Water jet Special risks CO x Special safety equipment required for fire fighting Fire-fighters should wear self-contained breathing apparatus. 6 Accidental Release Measures Personal precautions Remove sources of ignition. Avoid skin and eye contact. Caution, increase risk of slipping on escaped product. Environmental protection Do not allow the product to get into open water, sewers or soil. If the product escapes into surface water, sewers or into the soil, notify the relevant authority. Cleaning / Removal procedure Mop up the fluid with sand, soil or universal binding agent and dispose of it in accordance with the regulations.

3 7 Handling and Storage Page 3 of 6 Instructions for handling Avoid unprotected skin contact. Use gloves (e.g. nitrile rubber) or suitable skin protection creams. Avoid the formation of vapours and aerosols wherever possible. Storage instructions Store in a place protected from frost and heat. Store in a sealed container. Take action to prevent from electrostatic charging. Requirements on storage rooms/conditions Containers and decanting equipment are to be stored / handled in such a way as to rule out any risk to water and soil from escaping product. Storing with other substances Storage class 3B (VCI, Germany) *8 Exposure Controls / Personal Protection Technical safety action Provide adequate ventilation, if necessary by using local extraction systems. Exposure limits CAS-No. Name of substance Exposure limits Overshoot factor Notes. Hydrocarbon mixtures 200 ml/m 3 4 MAK, Germany (group 1) 1000 mg/m 3 General personal safety Wash hands before breaks and meals. Use reconditioning cream after work. Keep away from food and drink. Do not carry any cleaning cloths saturated with the product in your clothes. Breathing apparatus Not required if adequate ventilation is provided. Skin protection Wear protective gloves of suitable material (e.g. nitrile rubber, permeation time > 480 min) Use suitable skin protection cream that is not dissolved by oil if gloves cannot be worn. Eye protection Wear safety goggles if there is a risk of splashing. Safety clothing Work clothing.

4 9 Physical and Chemical Properties Page 4 of 6 Form Colour Odour liquid yellow slightly characteristic ph value ( g/l water, 20 C) not applicable Boiling point / range not determined C Flash point 70 C Ignition temperature 240 C Explosive limits lower 0,6 Vol% upper 6,5 Vol% Vapour pressure (20 C) < 1 hpa Density (20 C) 860 kg/m³ Solubility in water Distribution coefficient n-octanol/water (log POW) practically insoluble not determined Kinematic viscosity (40 C) 13 mm²/s

5 10 Stability and Reactivity Conditions to be avoided Stable in normal conditions for proper usage. See storage instructions. Substances to be avoided Strong oxidation agents Hazardous decomposition products In the event of fire CO x Page 5 of 6 11 Toxicological Information Acute oral toxicity LD 50 (oral, rat) > 2000 mg/kg (Toxicological evaluation of the individual components in the preparation) Irritation on the skin Skin contact by revise exposition may cause slight irritation. Skin sensitisation No sensitising effect known. Irritation on the eye Eye contact may cause slight temporary irritation. Other information Aspiration can lead to irritation of the bronchia and lungs, in serious cases to pulmonary edema and inflammation of the lungs, and trigger disorders of the central nervous system. 12 Ecological Information Eco-toxicity The product is potentially polluting in water do not allow it to get into the soil, sewer or open water. 13 Disposal Considerations Product In compliance with the local official regulations, hand over to a licensed waste disposal contractor.

6 EU waste code synthetic machining oils Page 6 of 6 Contaminated packaging Empty the vessel completely. Hand over to a licensed waste disposal contractor. Barrels and containers can be reconditioned. They can be cleaned by the reuser. 14 Transport Information Not a hazardous substance according to ADR/RID, IMDG, IATA/ICAO *15 Regulatory Information Identification according to EEC Directives Hazard symbol / marking not applicable References to particular hazards R 53 Can have fairly long-term harmful effects in waters. Safety hints S 61 Avoid releasing substance into the environment. Request special instructions/consult safety data sheet. National regulations (Germany) Potential water-polluting class WGK 1 (minor potential water pollutant, VwVwS dated 17 may 1999) *16 Other Information List of the special risks according to Chapter 2 R 53 Can have fairly long-term harmful effects in waters. R 65 Dangerous to health: Can cause lung damage if swallowed. R 66 Repeated contact can lead to chapped or cracked skin. Update service Revised sections are marked with an asterisk *. This information is based on our current knowledge. It is intended to describe our products in terms of their safety requirements and therefore is not designed to provide any assurance of certain characteristics.