NOTICE. Duct Mounted Environmental CO 2. Sensors. Product Identification. quick install. Dimensions. environmental Sensors VERIS INDUSTRIES

Transcription

1 VERIS INDUSTRIES environmental Sensors INSTLLTION GUIDE D Series DL NOTIE This product is not intended for life or safety applications. Do not install this product in hazardous or classified locations. Read and understand the instructions before installing this product. Turn off all power supplying equipment before working on it. The installer is responsible for conformance to all applicable codes. Product Identification DELUE MODEL: RH Option Temp Sensor Type DL S H = RH2% = NO RH EONOMY MODEL: DE (no options) Dimensions 6.7" (170 mm) T = Temp = No Temp (Stop Here) 3.1" (78 mm) = Transmitter B = 100R Platinum, RTD = 1k Platinum, RTD D = 10k T2, RTD, Thermistor E = 2.2k, Thermistor F = 3k, Thermistor G = 10k P, Thermistor H = 10k T3, Thermistor J = 10k Dale, Thermistor K = 10k w/11k shunt, Thermistor M = 20k NT, Thermistor N = 1800 ohm, Thermistor R = 10k US, Thermistor S = 10k 3221, Thermistor T = 100k, Thermistor U = 20k D, Thermistor 10.2" (258 mm) DE Optional al ert. Blank = None 1 = 1 pt Temp ert 2 = 2 pt Temp ert Duct Mounted Environmental O 2 Sensors Installer s Specifications D Series Input Voltage 20 to 30VD, 24 nalog Output 4-20m, (clipped & capped)/0-10vd (selectable)- DE models 4-20m, (clipped & capped)/0-5vd/0-10vd (selectable)- DL models Sensor urrent Draw 100m Maximum Operating Temperature Range 0 to 50 (32 to 122 F) Housing Material High impact BS plastic O2 Transmitter: Sensor Type Non-dispersive infrared (NDIR), diffusion sampling Measurement Range ppm or ppm, user selectable on DL models, ppm on DE models ccuracy ±30 ppm ±2% of measured value* Repeatability ±20 ppm ±1% of measured value Response Time <60 seconds for 90% step change RH Transmitter: HS Sensor Digitally profiled thin-film capacitive (32-bit mathematics); U.S. Patent 5,844,138 ccuracy ±2% from 10 to 80% 25 ; Multi-point calibration NIST Hysteresis 1.5% typical Linearity Included in ccuracy spec. Stability 20 (68 F) annually, for two years Operating Humidity Range 0 to 100% RH Operating Temperature Range 10 to 35 (50 to 95 F) Temperature oefficient ±0.1% RH/ above or below 25 (typical) Temperature (Transmitter): Sensor Type Solid-state, integrated circuit ccuracy ±0.5 (±1 F) typical Resolution 0.1 (0.2 F) Range 10 to 35 (50 to 95 F) Relay ontacts: 1 Form 1@30VD, resistive; 30W max. Note: Specified accuracy with 24VD supplied power with rising humidity. RTD/Thermistors in wall packages are not compensated for internal heating of product. EM onformance: EN :2001 (mended by 11:2004) lass B, EN :2001 EM Test Methods: ISPR 22:2006, IE :2001, IE :2006, IE :2004, IE :2006, IE :2001, IE :2004 EM Special Note: onnect this product to a D distribution network or an /D power adaptor with proper Surge protection (EN :2001 specification requirements). * Measured at NTP quick install 1. Mark and drill the three holes for the duct probe as shown. The centerline must be parallel to the air flow through the duct. 2. Rotate the duct probe so that its widest surface is perpendicular to the air flow in the duct. 3. Insert the probe and secure the sensor to the duct with sheet metal screws, making sure that the provided gasket material is compressed between the sensor housing and the air duct. 4. Wiring. See wiring diagrams on next page. 2.4" (61 mm) 7.8" (97 mm) Z G PGE Veris Industries US or +1(0) / support@veris.com lta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris V logo are trademarks or registered trademarks of Veris Industries, L.L.. in the US and/or other countries.

2 VERIS INDUSTRIES D Series INSTLLTION GUIDE Installation 1. hoose a location to mount the sensor. The centerline of the housing must be parallel to the direction of air flow in the duct. 2. Use the mounting diagram to drill three holes in the duct for securing the sensor. 3.1" (78 mm) 6.7" (175 mm) 1" diameter L 2.2" (56 mm) 0.4" x.0.2" (typical) 1" (26 mm) typ 0.3" (6 mm) typ WIRING 1. Feed control wire through conduit adapter and grommeted compression fitting on the bottom of the housing. 2. Remove terminal blocks by pulling straight up on the green assemblies. 3. onnect wires as shown and push terminal blocks back in to black receptacles. 4. Tighten compression fitting around control wire until sealed. 5. Snap conduit adapter onto compression fitting. 6. Refer to specifications for power requirements and relay rating. 7. Select m or Volt output using selector switch. DL Model - O2 Only 5.7" (144 mm) 3. Insert the probe into the hole. Rotate the housing so that the widest surface is perpendicular to the air flow.. onfiguration Pushbuttons PLUS ENTER MINUS V+ O2-OUT GND N OMM NO m Volt ir Flow ir Flow Rotate the duct probe so the channeled side is perpendicular to the air flow of the duct 1/2 NPT MLE ONDUIT DPTER 1/2 NPT FEMLE OUPLER 4. ttach the sensor to the duct using sheet metal screws. Make sure that the gasket on the back of the housing is compressed between the housing and the duct for a secure fit. 5. Wire the device. See Wiring section. 6. onfigure the system using the menu (DL only; see onfuguration section). 7. alibrate using 0 ppm O2 gas (see alebration section). ONFIGURTION PUSHBUTTONS PLUS ENTER MINUS DL Model with Temp & RH Options RH OUT V+ O2 OUT TEMP OUT/RTD GND RTD N OMM NO m Volt DE Duct Model LIBRTION PUSHBUTTON ENTER m Volt ON TEM OFF V+ O2-OUT GND LED ONDUIT DPTER 1/2 NPT MLE/FEMLE Z G PGE Veris Industries US or +1(0) / support@veris.com lta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris V logo are trademarks or registered trademarks of Veris Industries, L.L.. in the US and/or other countries.

3 VERIS INDUSTRIES D Series INSTLLTION GUIDE configuration - DL only * RUN MODE: 0 O2 ONLY MODEL *INDITES RELY STTUS O2/RH OMBO MODEL O2/T OMBO MODEL O2/RH/T OMBO MODEL TOGGLE %RH ND DEGREES P P M O P P M O. O % R H P P M F P P M ONFIGURTION MODE: PRESS [ENTER] FOR ONFIGURTION MODE. PRESS PLUS OR MINUS TO HNGE SETTING. S E T P O O 2 RNGE 500 TO PPM INREMENT D E D B RNGE 10 TO PPM INREMENT OPTIONS RE 2000 OR 5000 OPTIONS RE ON, LOW, OFF SEE NET PGE FOR EPLNTION (TEMP MODELS ONLY) OPTIONS RE ºF or º (VOLTGE MODE ONLY) OPTIONS: 0-10V OR 0-5V DEFULT IS 0-10V (m MODE ONLY) I N T O R N G E O 2 B M O N D D E + U N I T S º + O U T P U T V + O U T P U T m LIBRTION MODE: PUSH ND HOLD PLUS ND MINUS FOR 5 SEONDS TO ENTER MODE. PRESS RROW TO HNGE OPTION. PUSH ENTER FOR NET SELETION. S E R I L DISPLYS SERIL NUMBER DISPLYS MODEL NUMBER O F F S E T º O % F R O NOTE: This product is factory calibrated. The typical O2 sensor calibration interval is 5 years, dependent on specific site installation factors. s of the date of this document, compliance with NSI/SHRE requires minimum on-site accuracy verification intervals of 6 months, or per the building operation and maintenance manual. ccuracy verification should be performed using a comparison to a known reference, or the O2 gas calibration kit available from Veris Industries as model 01. WRNING: O2 sensor calibration requires gas calibration kit. Performing calibration without gas kit will cause erroneous readings. onsult factory for calibration kit. RNGE IS -5 TO 5º 0.1º INREMENT (O2/temp combo models) F H S RNGE -10 TO 10% 0.1% INREMENT (O2/RH combo models) 2 OPTIONS RE YES, NO OPTIONS RE NONE, 0, 400 Unit will automatically return to run mode when calibration is complete. E T.. + L W O R K I N G G * 5 : 0 0 L S?? + Z G PGE Veris Industries US or +1(0) / support@veris.com lta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris V logo are trademarks or registered trademarks of Veris Industries, L.L.. in the US and/or other countries.

4 VERIS INDUSTRIES D Series INSTLLTION GUIDE LIBRTION PROESS: DL models 1. Hook up hose to plastic port located on sensing module. 2. Start flowing nitrogen gas (0 ppm only). 3. Enter alibration mode as described on page 3. STEP 1: alibration Port LIBRTION PROESS: De models 1. Hook up hose to plastic port located on sensing module. 2. Start flowing (Nitrogen) 0 ppm Gas (0 ppm only). 3. Push and hold down calibration button until the LED illuminates. 4. ontinue flowing gas through the sensor until the LED is off - estimated calibration time is 5 minutes. STEP 1: alibration Port onnect hose here Regulator Valve STEP 2: Flow Nitrogen. Regulator Valve STEP 2: Flow Nitrogen onnect hose here NITROGEN GS NITROGEN GS STEP 3: alibrate for 5 min. Unit will return to working display when finished. STEP 3: alibrate 5 min. Push and hold down calibration button Green LED B LIBRTION LGORITHM B (utomatic Baseline alibration) is a patented self-calibration feature, which automatically adjusts the O 2 sensor to compensate for drift. When B is enabled, the lowest reading within every 24-hour period is recorded and analyzed over a running 7 day or 28-day period. If a statistically significant amount of drift is detected, an automatic correction factor is applied. This enables the sensor to operate within specifications for the 5-year calibration interval. NOTE: fter changing the B settings, the unit will need to be power cycled to have B changes take effect. Z G PGE Veris Industries US or +1(0) / support@veris.com lta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris V logo are trademarks or registered trademarks of Veris Industries, L.L.. in the US and/or other countries.

5 VERIS INDUSTRIES D Series INSTLLTION GUIDE cdl model only DL versions have optional RH and temperature sensors. To Replace Humidity Sensor: Observe handling precautions for static sensitive devices to avoid damage to the circuitry which would not be covered under the factory warranty. 1. Power down unit 2. Open housing on tip of duct probe 3. Slide old RH sensor off pins 4. Slide new RH sensor onto pins 5. Power unit back on Pins Lift to open tip of probe HS Sensor OUTPUT SLING Output scaling: ppm O2 ppm 0-5 Volt Output 0-10 Volt Output m Output Outside to to to 8 Over Ventilated Under 600 under 1.5 Under 3 Under 8.8 Ideal Ventilation to to to 11.2 Under Ventilated Over 900 over 2.25 Over 4.5 Over 11.2 Z G PGE Veris Industries US or +1(0) / support@veris.com lta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris V logo are trademarks or registered trademarks of Veris Industries, L.L.. in the US and/or other countries.

6 VERIS INDUSTRIES environmental Sensors INSTLLTION GUIDE W Series W Series Wall Mounted Environmental O 2 Sensors NOTIE This product is not intended for life or safety applications. Do not install this product in hazardous or classified locations. Read and understand the instructions before installing this product. Turn off all power supplying equipment before working on it. The installer is responsible for conformance to all applicable codes. Product Identification WLL EONOMY MODELS: Sensor Type WE S WLL DELUE MODELS: WL S WL B = 100R Platinum, RTD = 1k Platinum, RTD D = 10k T2, Therm. E = 2.2k, Therm. F = 3k, Therm. G = 10k P, Therm. H = 10k T3, Therm. J = 10k Dale, Therm. RH Option Temp Sensor Type H = RH 2% = No RH T = Temp = No (stop here) WE = Transmitter B = 100R Platinum, RTD = 1k Platinum, RTD D = 10k T2, Therm. E = 2.2k, Therm. F = 3k, Therm. G = 10k P, Therm. H = 10k T3, Therm. Temp al ert Option Setpoint Slider Value = No 1 = 1pt Temp al 2 = 2pt Temp al Options vailable 1 = Push Button Override * 2 = Set Point Slider 3 = Push Button Override*+Set Point Slider K = 10k w/11k shunt, Therm. M = 20k NT, Therm. N = 1800 ohm, Therm. R = 10k US, Therm. S = 10k 3221, Therm. T = 100k, Therm. U = 20k D, Therm. = 1k F = 10k G = 20k K = 50k M =100k J = 10k Dale, Therm. K = 10k w/11k shunt, Therm. M = 20k NT, Therm. N = 1800 ohm, Therm. R = 10k US, Therm. S = 10k 3221, Therm. T = 100k, Therm. U = 20k D, Therm. * Note: the Pushbutton Override feature is not available with temperature transmitter models. Only resistive temperature models qualify for this feature. Installer s Specifications Input Voltage 20 to 30VD, 24V nalog Output WE: 4-20m, 0-10VD (selectable); WL: 4-20m (clipped and capped)/0-5vd/0-10vd (selectable) Sensor urrent Draw 100m max. Operating Temperature Range 0 to 50 (32 to 122 F) Housing Material High impact BS plastic O 2 Transmitter: Sensor Type Non-dispersive infrared (NDIR), diffusion sampling Measurement Range WL: ppm or ppm, user selectable; WE: ppm ccuracy ±30 ppm ±2% of measured value* Repeatability ±20 ppm ±1% of measured value Response Time <60 seconds for 90% step change RH Transmitter: HS Sensor Digitally profiled thin-film capacitive (32-bit mathematics); U.S. Patent 5,844,138 ccuracy ±2% from 10 to 80% 25 ; Multi-point calibration NIST Hysteresis 1.5% typical Linearity Included in ccuracy spec. Stability 20 (68 F) annually for two years Operating Humidity Range 0 to 100% RH, noncondensing Operating Temperature Range 10 to 35 (50 to 95 F) Temperature oefficient ±0.1% RH/ above or below 25 (typical) Temperature (Transmitter): Sensor Type Solid-state, integrated circuit ccuracy ±0.5 (±1 F) typical Resolution 0.1 (0.2 F) Range 10 to 35 (50 to 95 F) Relay ontacts: 1 Form (on models without setpoint slider option) 1@30VD, resistive; 30W max. Note: Specified accuracy with 24VD supplied power with rising humidity. RTD/Thermistors in wall packages are not compensated for internal heating of product. EM onformance: EN :2001 lass B, EN :2001, EN :2000, EN :2001 EM Test Methods: ISPR 22:1997(mended 9:2000, 2:2002), IE :2001, IE :2002, IE :2004, IE :2001, IE :2004, IE :2001, IE :2004. EM Special Note: onnect this product to a D distribution network or an /D power adaptor with proper SURGE PROTETION (EN :2001 specification requirements) * Measured at NTP Quick Install 1. Select a mounting location away from ventilation sources. The sensor should be mounted on a vertical wall, about 4 1/2 feet above the floor. 2. ffix the backplate to the wall. 3. Wire the device. Refer to wiring diagrams on page Install over. Z H PGE Veris Industries US or +1(0) / support@veris.com lta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris V logo are trademarks or registered trademarks of Veris Industries, L.L.. in the US and/or other countries.

7 VERIS INDUSTRIES W Series INSTLLTION GUIDE Dimensions 6. Wire the backplate. O2, RH, Temperature Transmitter Options 4.8" (122 mm) + - POWER SUPPLY 20-30VD, 24V 3.5" (89 mm) installation 1.2" (30 mm) 1. Remove the cover by pressing the tab at the top of the sensor while pulling outward from the top of the cover. PWR O2 OUTPUT OMMON RH OUTPUT TEMP OUTPUT RELY N.O. OMMON RELY N.. - ONTROL SYSTEM OMMON O2 INPUT RH INPUT TEMP INPUT RELY N.O. OMMON RELY N.. Note: onnector blocks and headers for optional features are not included with non-option models. O2, RH, Thermistor/RTD, Pushbutton Override, and Setpoint Slider Options 2. Remove the backplate by unfastening the sensor from the bottom of the backplate and pivoting the sensor outward. 3. Punch out openings in the backplate. Observe handling precautions for static sensitive devices to avoid damage to the circuitry which would not be covered under the factory warranty. 4. Position the sensor vertically on the wall, 4 1/2 feet above the floor. ll optional connector blocks are shown here for clarity. PWR O2 OUTPUT OMMON RH OUTPUT RTD/THERMISTOR/OVERRIDE RTD/THERMISTOR/OVERRIDE SLIDER RIGHT SLIDER WIPER SLIDER LEFT + O2, Economy Model - - POWER SUPPLY 20-30VD, 24V ONTROL SYSTEM OMMON O2 INPUT RH INPUT THERMISTOR/OVERRIDE INPUT SETPOINT SLIDER INPUT Note: Relay contacts not available in this configuration. Note: onnector blocks and headers for optional features are not included with non-option models. + - POWER SUPPLY 20-30VD, 24V correct incorrect - ONTROL SYSTEM OMMON O2 INPUT 5. Mount the backplate onto the wall using the screws provided. Five screwholes available; use a minimum of two for secure mounting. PWR O2 OUTPUT OMMON RTD/THERMISTOR/OVERRIDE RTD/THERMISTOR/OVERRIDE THERMISTOR/OVERRIDE INPUT ll optional connector blocks are shown here for clarity. Z H PGE Veris Industries US or +1(0) / support@veris.com lta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris V logo are trademarks or registered trademarks of Veris Industries, L.L.. in the US and/or other countries.

8 VERIS INDUSTRIES W Series INSTLLTION GUIDE 7. Install the sensor onto the backplate. 8. Use the switch to select voltage or current output. For WL model, see onfiguration section on page 4. V O LT 9. When installation is complete, install the cover and snap into place. B LIBRTION LGORITHM B (utomatic Baseline alibration) is a patented self-calibration feature, which automatically adjusts the O2 sensor to compensate for drift. When B is enabled, the lowest reading within every 24-hour period is recorded and analyzed over a running 7-day or 28-day period. If a statistically significant amount of drift is detected, an automatic correction factor is applied. This enables the sensor to operate within specifications for the 5-year calibration interval. ON POSITION. Recommended Setting. Use the ON setting for applications where the building is unoccupied within a 24-hour timeframe. This setting runs the B for a 7-day average. LOW POSITION. Use the LOW setting for buildings occupied 24 hours a day. This setting extends the B to a 28-day average. OFF POSITION. Not Recommended. MP OUTPUT SLING O2 - arbon Dioxide Sensor Output scaling: ppm O2 PPM 0-5 VOLT OUTPUT 0-10 VOLT OUTPUT m OUTPUT Outside to to to 8 Over Ventilated Under 600 under 1.5 Under 3 Under 8.8 Ideal Ventilation to to to 11.2 Under Ventilated Over 900 over 2.25 Over 4.5 Over 11.2 RH - Relative Humidity Sensor Output scaling: 0-100% T - Temperature Transmitter Output scaling: 10 to 35 (50 to 95 F) To determine temperature from output reading: 1) ompute Total Span from Temperature Range: Maximum range - Minimum range = Total span ex. 10 to 35 range» = 25 Total span 2) ompute Output % of Span from Reading: (Reading - Minimum Output) / (Maximum output - Minimum output ex m reading on 4-20m output: ( )/(20-4)=7.10/16=0.444=44.4% ex. 4.44v reading on 0-10v output: (4.44-0)/(10-0)=4.44/10=0.444=44.4% 3) ompute Temperature: (Total span x Output % of Span) + Minimum range ex. 44.4% Output, Total Span = 45, range = 50/95: (0.444 x 45) + 50 = = 70 Example outputs for selected temperatures: Temp 4-20m 0-10v 0-5v m 3.33v 1.67v m 4.44v 2.22v m 5.56v 2.78v Refer to alibration Mode procedures on previous page to set desired B mode for WL models. ON B Settings (WE only) LOW OFF ON ON ON LOW LOW LOW OFF OFF OFF Z H PGE Veris Industries US or +1(0) / support@veris.com lta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris V logo are trademarks or registered trademarks of Veris Industries, L.L.. in the US and/or other countries.

9 VERIS INDUSTRIES W Series INSTLLTION GUIDE configuration - WL only RUN MODE: * 0 O2 ONLY MODEL *INDITES RELY STTUS O2/RH OMBO MODEL O2/T OMBO MODEL O2/RH/T OMBO MODEL TOGGLE %RH ND DEGREES P P M O P P M O. O % R H P P NOTE: This product is factory calibrated. The typical O2 sensor calibration interval is 5 years, dependent on specific site installation factors. s of the date of this document, compliance with NSI/SHRE requires minimum on-site accuracy verification intervals of 6 months, or per the building operation and maintenance manual. ccuracy verification should be performed using a comparison to a known reference, or the O2 gas calibration kit available from Veris Industries as model 01. WRNING: O2 sensor calibration requires gas calibration kit. Performing calibration without gas kit will cause erroneous readings. onsult factory for calibration kit. M F P P M ONFIGURTION MODE: PRESS [ENTER] FOR ONFIGURTION MODE. PRESS PLUS OR MINUS TO HNGE SETTING. S E T P O O 2 RNGE 500 TO PPM INREMENT D E D B RNGE 10 TO PPM INREMENT OPTIONS RE 2000 OR 5000 OPTIONS RE ON, LOW, OFF SEE NET PGE FOR EPLNTION (TEMP MODELS ONLY) OPTIONS RE F or (VOLTGE MODE ONLY) OPTIONS: 0-10V OR 0-5V DEFULT IS 0-10V (m MODE ONLY) I N T O R N G E O 2 B M O N D D E + U N I T S º + O U T P U T V + O U T P U T m LIBRTION MODE: PUSH ND HOLD PLUS ND MINUS FOR 5 SEONDS TO ENTER MODE. PRESS RROW TO HNGE OPTION. PUSH ENTER FOR NET SELETION. O F F S E T º O % S E R I L RNGE IS -5 TO 5, 0.1 INREMENT (O2/temp combo models) F R F H S RNGE -10 TO 10%, 0.1% INREMENT (O2/temp combo models) O DISPLYS SERIL NUMBER 2 OPTIONS RE YES, NO OPTIONS RE NONE, 0, 400 Unit will automatically return to run mode when calibration is complete. E T.. + W O R K I N G DISPLYS MODEL NUMBER L G * 5 : 0 0 L S?? + Z H PGE Veris Industries US or +1(0) / support@veris.com lta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris V logo are trademarks or registered trademarks of Veris Industries, L.L.. in the US and/or other countries.

10 VERIS INDUSTRIES W Series INSTLLTION GUIDE LIBRTION PROESS: WL models 1. Remove cover and connect gas hose to calibration port. 800 PPM 70.0 F onnect hose here LIBRTION PROESS: WE models 1. Remove cover and connect gas hose to calibration port. LED indicator onnect hose here 2. Enter alibration Mode menu per directions on page 3. hoose 0 ppm calibration gas option. 3. Flow Nitrogen 2. Flow Nitrogen Regulator Valve Regulator Valve NITROGEN GS NITROGEN GS 3. Press and hold down the ENTER button until the green LED illuminates. 4. alibrate for 5 minutes. Unit will return to run mode when calibration is complete. 800 PPM 70.0 F LED indicator onnect hose here ENTER button 4. ontinue flowing gas until the LED goes off. Z H PGE Veris Industries US or +1(0) / support@veris.com lta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris V logo are trademarks or registered trademarks of Veris Industries, L.L.. in the US and/or other countries.

11 Indoor ir Quality Meter 1010 Rev. 2.x Meters The Value Leader TM

12 ontents 1. Introduction 2. General Overview 3. Familiarization 3.1 Front View 3.2 Soft Keys 3.3 Back View 4. Operation 4.1 Turning On & Off / Performing a Test / Main Display 4.2 Selecting Temperature Units 4.3 mbient / Dew Point / Wet Bulb Temperature Display 4.4 Temperature / lock Display Modes 4.5 ctivating the Backlight 4.6 Setting Date and Time 4.7 Setting O larm Level 5. alculating % Outside ir 5.1 % Outside ir (Temperature) 5.2 % Outside ir (arbon Dioxide) 6. Data Logging 7. Retrieving Logged Data 8. Technical Specifications 9. Maintenance 9.1 Battery Replacement 9.2 Service 10. Technical Information 1. Introduction Thank you for purchasing TPI brand products. The TPI 1010 Indoor ir Quality (IQ) Meter is a state of the art, easy to use tester designed to provide you with the necessary measurements to monitor and make adjustments to air handling devices. The instrument is ruggedly constructed and comes with a 3 Year unit and 2 Year sensor Guarantee. 2. General Overview The 1010 IQ meter uses state of the art sensors to measure humidity, carbon monoxide (O), carbon dioxide (O2), and temperature. The O and O2 sensors in your meter will need to be replaced periodically and calibration is recommended once every year. The O sensor is electrochemical and this type of sensor is always active once installed in the unit. Therefore the time the unit is off and not being used must be taken into account when determining sensor life. The sensors in your analyzer are warranted for two years. This warranty does not cover sensors damaged through misuse of the meter. You should keep battery power applied to your sensors at all times. The following guidelines will help prevent damage to your sensors: lways store your unit in a place where the temperature does not get down to or below freezing. lways maintain battery power to the sensors. When the batteries get low replace them as soon as possible. Never allow foreign objects or material to enter the sensor holes, damage to the sensor may result. Never over saturate your sensors by performing tests on equipment with gas levels beyond the capability of you analyzer.

13 General Overview (ontinued) This manual will guide you through the functions of the TPI 1010 which will give you many years of reliable service. Your TPI 1010 Indoor ir Quality meter comes complete with the following standard accessories: TPI 1010 Instrument Protective Rubber Boot (800) Soft arrying ase (921) USB able & Software (803) Instruction Manual Your TPI 1010 Indoor ir Quality meter has the following optional accessories available: Power adapter / Battery eliminator (804) Magnetic strap kit to hang meter (127) Boot hook to hang meter (103) Replacement Software only (802) Replacement USB cable only (801) ( ) Denotes part number 3. Familiarization 3.1 Front View O Sensor Location Protective Rubber Boot USB Port O2 Sensor Location Humidity & Temperature Sensor Location Display Keypad Power dapter Sensor Locations: Display : Protective Rubber Boot Keypad USB Port Power dapter Socket Places where the O, O2, and Humidity sensors are located and protected. Large 4 Parameter Backlit LD Display. Provides protection to meter housing and sensors. Selects all available functions Location for connection of USB cable for P com munication. Location to connect power adapter.

14 3.2 Soft Keys 3.3 Back View On / Off key - Used to turn the IQ meter on or off. Press to turn on, press and hold to turn off. Up rrow key - Used to select and change parameters. lso used to cycle through dew point and wet bulb temperatures from the main display. Left rrow key - Used to select and change parameters. Hanger Hole Right rrow key - Used to select and change parameters. Down rrow key - Used to select and change parameters. Enter key - Used to activate % outside air mode. lso used to accept parameter changes. Mode key - Used to activate and deactivate data logging mode. Press and hold to activate or deactivate logging. Backlight key - Used to turn the display backlight on and off. Tilt Stand T/ key - Used to switch the bottom display between temperature / humidity and time display modes. Battery over Screw Unit key - Used switch the bottom temperature display between Fahrenheit and elsius modes. Hanger Hole: Tilt Stand: Batter over Screw: Use to hang instrument for hands free operation. an be used with 127 magnetic strap kit or 103 hook. Use to stand instrument on a table. Loosen this screw and open cover to access batteries.

15 4. Operation 4.1 Turning On & Off / Performing a Test / Main Display lways: - Turn the 1010 on outside of the area to be tested. Make sure the unit is in fresh air (no carbon monoxide present) prior to turning on. This will allow the O sensor to set to zero properly. 4.2 Selecting Temperature Units Pressing the key switches the temperature display between F and. 4.3 mbient / Dew Point / Wet Bulb Temperature Display Repeatedly pressing the key from the main display cycles through dew point temperature, wet bulb temperature, and ambient temperature displays. Press the key and the 1010 will begin a 30 second countdown. During this time the 1010 performs a self diagnostic and sets the O sensor to zero. Once the countdown ends the 1010 will display O2, O, Temperature, and Humidity. Enter the area to be tested, the measured values will be displayed. arbon dioxide (O2) in parts per million (ppm) is displayed at the top, carbon monoxide (O) in parts per million (ppm) is displayed in the middle, temperature in F or (selectable), and humidity in percent are displayed at the bottom of the main display. The battery indicator is located at the bottom left of the display. When the batteries become low they must be replaced to maintain proper operation. arbon dioxide (O2) mbient Temperature 4.4 Temperature / lock Display Modes 4.5 ctivating the Backlight Dew Point Temperature Indicated by DP in the display Wet Bulb Temperature Indicated by WB in the display Pressing the key from the main display cycles between temperature and clock display. To set the clock please refer to section 4.6. Battery indicator arbon monoxide (O) Temperature Humidity Pressing the key turns the display backlight on and off. Power consumption is much higher when the backlight is activated. The backlight will automatically turn off 30 seconds after it is activated. To conserve battery life the backlight should only be used when necessary. To turn the 1010 off, press and hold the key down until the 1010 turns off. If 30ppm or more O is measured the 1010 will beep and the display will flash red as a warning. This alarm point is adjustable. dditional functions can be activated during testing. Please see next sections.

16 4.6 Setting Date and Time 4.7 Setting O larm Level 1) Starting with the 1010 turned off, press and hold down the key then press and hold down the key until two beeps are heard and the time / date screen is displayed. The 1010 is equipped with an audible and visual alarm for carbon monoxide. The alarm level is factory set at 30ppm. When O above this level is measured, the 1010 will beep and the display will flash red. The alarm level is adjustable and can be set from 10ppm to 500ppm. Year 1) With the 1010 turned on, press and hold down the until the O alarm screen is displayed. and keys Month / Day O alarm level in ppm Hour / Minutes (24 hour clock, HH:MM) 2) Using the rrow keys, set the year. Once the year is set, press 3) Using the rrow keys, set the month. Once the month is set, press 4) Using the rrow keys, set the day. Once the day is set, press 5) Using the rrow keys, set the hour. Once the hour is set press 6) Using the rrow keys set the minutes. Once minutes is set, press The 1010 will return to normal operation. Using the rrow keys set the alarm point to the desired level. The keys select the digit and the keys increase or decrease the value. Once the desired alarm point is set, press the key to return to normal operation.

17 5. alculating % Outside ir HV systems use a combination of outside air, supply air, and return air to maintain consistent and comfortable air quality. The 1010 can calculate outside air either by measuring temperature or by measuring O2. The formula used to calculate % outside air is: Percent outside air can be calculated using either temperature or carbon dioxide. 5.1 % Outside ir (Temperature) To activate % outside air mode, press the displayed in the middle display area. key about 2 seconds until t-0 is 1) Place the sensor of the 1010 perpendicular to the Return air flow. When the reading stabilizes press the key and capture the return air temperature, "t-1" is displayed. 2) Place the sensor of the 1010 perpendicular to the Supply air flow. When the reading stabilizes press the key and capture the supply air temperature, "t-2" is displayed. 3) Place the sensor of the 1010 perpendicular to the Outside air flow. When the reading stabilizes press the key and capture the outside air temperature, "t-3" is displayed. 4) Press the key, "t =" will be displayed and the calculated percent outside air will be displayed at the top of the display. 5) If you want to perform this measurement again, press the key once and return to step 1. 6) To exit and return to normal operation, press and hold the key until -0 is displayed. Press and hold the key until a beep is heard and the 1010 returns to normal operation. 5.2 % Outside ir (arbon Dioxide) To activate % outside air mode, press the key about 2 seconds until t-0 is displayed in the middle display area. Press and hold the key until -0 is displayed. 1) Place the sensor of the 1010 perpendicular to the Return air flow. When the reading stabilizes press the key and capture the return air temperature, "-1" is displayed. 2) Place the sensor of the 1010 perpendicular to the Supply air flow. When the reading stabilizes press the key and capture the supply air temperature, "-2" is displayed. 3) Place the sensor of the 1010 perpendicular to the Outside air flow. When the reading stabilizes press the key and capture the outside air temperature, "-3" is displayed. 4) Press the key, " =" will be displayed and the calculated percent outside air will be displayed at the top of the display. 5) If you want to perform this measurement again, press the key once and return to step 1. 6) To exit and return to normal operation, press and hold the key until a beep is heard and the 1010 returns to normal operation.

18 6. Data Logging To activate data logging press and hold down the key until the logging setup screen is displayed. Once the logging function is activated all preciously logged data is written over. 7. Retrieving Logged Data To retrieve logged data the USB cable and P software (both supplied) must be used. Install the P software on your P and open it. onnect the 1010 to the P using the USB cable. lick on the connect to P button in the software window. The software can be used to retrieve logged data and for real time monitoring. OM port setting is: 1) INT is displayed at the top to indicate the 1010 is waiting for the logging interval to be set. The logging interval tells the 1010 how often to sample. For example, a logging interval of 10 seconds (00:10) means the 1010 will log a reading every 10 seconds. The bottom indicates the current logging interval in minutes and seconds (MM:SS) or hours and minutes (HH:MM). Flashing SE in the display indicates the last two digits are seconds and a flashing MIN in the display indicates the last two digits are minutes. In seconds mode the time is adjustable from 1 sec to 59 min 59 sec. In the minutes mode the time is adjustable from 1 min to 23 hr 59 min. Pressing the keys switches between the two time modes. 2) Once the time mode is set press the key and time digits will flash. Using the rrow keys set the interval to the desired level. The keys select the digit and the keys increase or decrease the value. Baud rate: Parity: None Data Bits: 8 Stop Bit: 1 3) Once the seconds have been entered, press the key to move to min / hr. 4) Using the rrow keys set the interval to the desired level. The keys select the digit and the keys increase or decrease the value. 5) Once the logging interval is set press the key and the 1010 will return to the main display and LOG will flash indicating the logging function is active. 6) To deactivate data logging press and hold down the key until LOG is no longer flashing. For data retrieval please see the next section on how to retrieve logged data.

19 8. Technical Specifications Function Range ccuracy O2 0 to 5000ppm 50 F~104 F: ±3% of rdg+75ppm <50 F, >104 F: ±5% of rdg+75ppm Temperature -5 F to 140 F ±2 F -20 to 60 ±1 Dew Point Temperature -47 F to 135 F alculation -44 to 57 Wet Bulb Temperature 3 F to 135 F alculation -16 to 57 Relative Humidity 5% to 95% ±2% RH O 0 to 500ppm ±3ppm or ±5% of rdg whichever is greater % Outside ir 0 to 100% alculation Data Logging: Up to 10,000 samples 1 sec to 23hr 59min interval. Display Type: 3 line with annunciators and backlight O larm: udible and visual, selectable level (factory default 30ppm) 9. Maintenance It is recommended that the instrument be calibrated every 12 months. Please consult Test Products International for further details (800) Battery Replacement When the batteries become low they will require replacement. 1. Turn the meter over so the back is facing you. 2. Loosen the screw holding down the battery cover located under the tilt stand. 3. Lift the tilt stand up and remove the battery cover. 4. Replace the batteries (3 x lkaline) and install the cover and tighten the screw. 9.2 Service To obtain warranty and non-warranty performance or maintenance on your analyzer: - Include with the product your name, address, phone number, written description of the problem and proof of purchase date. arefully package and return to: TPI / ttn. Repair 9615 SW llen Blvd. Suite 104 Beaverton, OR Operating Temperature & Humidity O and O2: 14 F to 122 F (-10 to 50 ) ll Other Function: -4 F to 140 F (-20 to 60 ) Humidity 15 ~ 95% non-condensing Storage Temperature: -4 F to 140 F (-20 to 60 ) Power supply 3 battery( 4.5V) /D adapter 5Vout (enter positive) Battery Life: 40 hours typical without backlight Output: Serial output via USB connection

20 10. Technical Information Notes: % Outside ir - HV systems use a combination of outside air, supply air, and return air to maintain consistent and comfortable air quality. The 1010 can calculate outside air either by measuring temperature or by measuring O2. The formula for % Outside ir is: If too little outdoor air enters a home, pollutants can accumulate to levels that can pose health and comfort concerns. Unless they are built with special mechanical means of ventilation, homes that are designed and constructed to minimize the amount of outdoor air that can 'leak' into and out of the home may have higher pollutant levels than other homes. However, because some weather conditions can drastically reduce the amount of outdoor air that enters a home pollutants can build up even in homes that are normally considered 'leaky'. Dew Point Temperature - This is the temperature at which condensation begins Wet Bulb Temperature - This is the lowest temperature evaporating water can reach Recommended Levels by gency Parameter IDPH 1 SHRE 2 OSH PEL 3 GIH TLV 4 Humidity 20% - 60% 30% - 60% N/ N/ Temperature (winter) (winter) N/ N/ (summer) (summer) arbon Dioxide 1,000ppm (<800ppm preferred) 1,000ppm 5,000ppm 5,000ppm arbon Monoxide 9ppm 9ppm 50ppm 25ppm N/-Not pplicable or Not Established 1 Illinois Department of Public Health (2009) 2 merican Society of Heating, Refrigerating and ir onditioning Engineers 3 Occupational Safety and Health dministration Permissible Exposure Limit -- this level is a time-weighted average and is an enforceable standard that must not be exceeded during any eight-hour work shift of a 40-hour work week. 4 merican onference of Governmental Industrial Hygienist Threshold Limit Value -- this level is a recommended time-weighted average upper limit exposure concentration for a normal eight to 10-hour workday and a 40-hour work week.

21 Test Products International, Inc SW llen Blvd., Ste. 104 Beaverton, OR Tel: Fax: Test Products International, Ltd. 342 Bronte Road South, Unit #9 Milton Ontario anada L9T5B7 Tel: Fax:

22 VERIS INDUSTRIES environmental Sensors INSTLLTION GUIDE O 2 alibration ccessory NOTIE This product is not intended for life or safety applications. Do not install this product in hazardous or classified locations. Read and understand the instructions before installing this product. Turn off all power supplying equipment before working on it. The installer is responsible for conformance to all applicable codes. Product Identification Introduction The 01 O 2 calibration accessory is designed for field calibration of any O 2 sensor produced by Veris Industries, regardless of age. It comes complete with calibration gas, a gas regulator, tubing, and fittings, which can be configured to easily calibrate your O 2 device. The calibration process normally takes about 5 minutes. In general, Veris O 2 sensors use a time-weighting factor, which saves the lowest concentration of O 2 measured in a selectable time period, and then use that information to calculate the ambient or base level O 2 concentration. This calculation allows your Veris O 2 sensor to improve its accuracy over time. To use this instruction guide, first identify the shape of O 2 sensor inside of your Veris device (rectangular or pear), and then turn to the appropriate section of this instruction manual for the specific instructions on how to calibrate your particular device. When connecting the gas regulator assembly to the gas bottle, verify there is at least 10 lbs of pressure remaining in the bottle. 01 Z B PGE Veris Industries US or +1(0) / support@veris.com lta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris V logo are trademarks or registered trademarks of Veris Industries, L.L.. in the US and/or other countries.

23 VERIS INDUSTRIES 01 INSTLLTION GUIDE For ny O 2 Device with Rectangular Sensor PREPRTION 1. Ensure unit to be calibrated is properly installed and has been operating for at least one hour. 2. Use only Veris Industries calibration kit model 01. Perform zero calibration with nitrogen gas. Use a flow regulator to limit gas flow to <0.25 lpm. Exceeding this flow rate may cause calibration errors. SETUP 1. Install tubing to regulator and screw regulator on gas bottle. 2. Remove front cover from unit and locate plastic barb fitting and menu pushbutton. label indicating push-button functions is located inside front cover plate. 5. Verify display indicates 0 PPM gas concentration. Press ENTER to continue. 6. Display should prompt to flow gas: Z E R O G S F * L O S 0 P P M W T Open regulator valve and adjust pressure to 7 psi to generate the appropriate flow rate. Press ENTER to begin countdown timer. * L T G R I S T M E S E 7. Wait for countdown timer to reach zero and for display to indicate calibration is complete: D O N E S T O P G S 3. ttach tubing firmly to barb fitting. /WL/DL LIBRTION 1. Press ENTER button to enter configuration mode. Menu Buttons Hose Barb 2. Press ENTER repeatedly until O L menu option appears on the display: 2 8. lose regulator valve and disconnect tubing from unit. Press ENTER to return to normal operation. 9. Replace sensor cover. DE/WE LIBRTION 1. Follow setup directions above. 2. Start flowing (nitrogen) 0 ppm O gas Push and hold down calibration button until the red LED illuminates. 4. ontinue flowing gas through the sensor until the red LED turns off. 5. Follow steps 8 & 9 of the calibration directions above. O 3. Press + to select YES option. 2 * Y E S N O L? 4. Using +/- buttons, select ZERO calibration option. Press ENTER to continue. NOTE: 01 kit includes nitrogen gas for zero calibration ONLY. * Z E R O S P N Z B PGE Veris Industries US or +1(0) / support@veris.com lta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris V logo are trademarks or registered trademarks of Veris Industries, L.L.. in the US and/or other countries.

24 VERIS INDUSTRIES 01 INSTLLTION GUIDE For DL/WL Device with Pear- Shaped Sensor 1. Remove cover to the device. 2. onnect hose to plastic port located on sensing module and flow gas (Nitrogen) O ppm O 2 gas through the sensor. O F F S E T º O F F S % R H E T.. Range is -5 to 5, 0.1 increment Range is -10 to 10%, 0.1% increment WL ONLY onnect hose here O 2 L? + Options are Yes/No L G S? + Options are None, 0, 400 WL W O R K I N G * 5 : 0 0 Unit will automatically return to run mode when calibration is complete. Regulator Valve DL NOTE: This product is factory calibrated. The typical O 2 sensor calibration interval is 5 years, depending on specific site installation factors. s of the date of this document, compliance with NSI/SHRE requires minimum on-site accuracy verification intervals of 6 months or per the building operation and maintenance manual. ccuracy verification should be performed using either a comparison to a known reference or the O 2 gas calibration kit available from Veris Industries as model 01. WRNING: O 2 sensor calibration requires a gas calibration kit. Performing calibration without a gas kit will cause erroneous readings. onsult factory for calibration kit. NITROGEN GS 4. Select 0 ppm al Gas option. 5. ontinue flowing gas through the sensor. Estimated calibration time is 5 minutes. Unit returns to run mode when calibration is complete. 3. Push and hold plus and minus buttons for 5 seconds to enter alibration mode. t each menu option, use the arrow to change values. Push enter for next option. S E R I L Displays serial number WL DL Displays model number Z B PGE Veris Industries US or +1(0) / support@veris.com lta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris V logo are trademarks or registered trademarks of Veris Industries, L.L.. in the US and/or other countries.

25 VERIS INDUSTRIES 01 INSTLLTION GUIDE For DE Device with Pear-Shaped Sensor 1. onnect hose to plastic port located on sensing module. For WE Device with Pear-Shaped Sensor 1. onnect hose to plastic port located on sensing module. onnect hose here onnect hose here 2. Start flowing (Nitrogen) 0 ppm Gas (0 ppm only). Regulator Valve 2. Start flowing (Nitrogen) 0 ppm Gas (0 ppm only). Regulator Valve NITROGEN GS NITROGEN GS 3. Push and hold down calibration button until the LED illuminates. Push and hold down calibration button 3. Push and hold down calibration button until the LED illuminates. Green LED Green LED 4. ontinue flowing gas through the sensor until the LED is off - estimated alibration time is 5 minutes. Push and hold down calibration button 4. ontinue flowing gas through the sensor until the LED is off - estimated alibration time is 5 minutes. Z B PGE Veris Industries US or +1(0) / support@veris.com lta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris V logo are trademarks or registered trademarks of Veris Industries, L.L.. in the US and/or other countries.