AN EASY-TO-USE GUIDE FOR ALL BLUEPRINT PRODUCTS

Transcription

1 AN EASY-TO-USE GUIDE FOR ALL BLUEPRINT PRODUCTS

2 TABLE OF CONTENTS PUCKS CHLORINE 2 STICKS CHLORINE 2 ALK INCREASER 10 PH INCREASER 10 PH DECREASER 11 CAL INCREASER 11 STABILIZE DRY 12 STABILIZE LIQUID 12 NEUTRALIZE 13 SOON 3 LATER 3 OXY 4 NOW 4 RESOLVE 5 ALGAE BREAK 40 6 SPRING AND FALL 6 PHOS REMOVE 7 PHOS REMOVE EXTRA 7 WEEKLY 8 CONSERVE 8 STAIN AND SCALE 9 METAL REMOVE 9 ALGAE BREAK REMEDY 14 STAIN LIFT 15 FILTER ASSIST 16 PIPE PURGE 16 CLEAR 17 CLEAR ONE SHOT 17 COVER CLEAN 18 CLEAN 18 FILTER CLEAN 19 KITS SPRING & FALL KIT 20 MAINTAIN 6 KIT 21 MAINTAIN 6 SALT KIT 22

3 PUCKS CHLORINE Stabilized chlorinating tablets Controls bacteria and algae in swimming pool waters kg kg WARNING: Direct Tablet Contact May Cause Bleaching of Vinyl or Painted Pool Surfaces. Automatic Feeding Devices Employing These Tablets Must be Totally Free from Traces of other Pool Sanitizers To Avoid the Probability of an Explosion. Maintain recommended daily levels as determined by testing kit. Free available chlorine: ppm ph: Total Alkalinity: ppm Calcium Hardness: ppm For outdoor pools, chlorine residuals can be protected from destruction by the sun s rays by adding 300 g of PUCKS CHLORINE per 10,000 litres of pool water to yield the required initial concentration of 30 ppm. If using an automatic chlorinator, fill the chamber[s] with tablets and adjust flow rate, according to manufacturer s recommendations, to maintain proper chlorine residual. Adding tablets to the pool s skimmer basket is an alternative chlorine feed method. Daily usage should approximate 25 g of PUCKS CHLORINE per 10,000 litres of pool water. Note: Hot weather, heavy pool usage and rain may require higher usage rates to maintain proper chlorine residuals. Periodic superchlorination of pool water is recommended. Follow label instructions of superchlorination product being employed. PUCKS CHLORINE contains stabilizer which can accumulate in pool water. Keep stabilizer within the range of ppm by dilution with fresh water. SANITIZE STICKS CHLORINE Stabilized chlorinating tablets Controls bacteria and algae in swimming pool waters kg kg WARNING: Direct Tablet Contact May Cause Bleaching of Vinyl or Painted Pool Surfaces. Automatic Feeding Devices Employing These Tablets Must be Totally Free from Traces of other Pool Sanitizers To Avoid the Probability of an Explosion. Maintain recommended daily levels as determined by testing kit. Free available chlorine: ppm ph: Total Alkalinity: ppm Calcium Hardness: ppm For outdoor pools, chlorine residuals can be protected from destruction by the sun s rays by adding 300 g of STICKS CHLORINE per 10,000 litres of pool water to yield the required initial concentration of 30 ppm. If using an automatic chlorinator, fill the chamber[s] with tablets and adjust flow rate, according to manufacturer s recommendations, to maintain proper chlorine residual. Adding tablets to the pool s skimmer basket is an alternative chlorine feed method. Daily usage should approximate 25 g of STICKS CHLORINE per 10,000 litres of pool water. Note: Hot weather, heavy pool usage and rain may require higher usage rate to maintain proper chlorine residuals. Periodic superchlorination of pool water is recommended. Follow label instructions of superchlorination product being employed. STICKS CHLORINE contains stabilizer which can accumulate in pool water. Keep stabilizer within the range of ppm by dilution with fresh water. BLUEPRINT PRODUCT RESOURCE GUIDE 2

4 SOON OXIDIZE Fast dissolving shock treatment Clears cloudy or dull water Does not add to cyanuric acid levels Maintain recommended daily levels as determined by testing kit. Free available chlorine: ppm ph: Total Alkalinity: ppm Calcium Hardness: ppm Each week add 150 g per 10,000 litres of pool water by sprinkling product over the surface of the pool. Note: Hot weather, heavy pool usage and rain may require higher dosages and more frequent use g g kg LATER Clears cloudy or dull water Helps keep swimming pool water sparkling clear Does not add to cyanuric acid levels Maintain recommended daily levels as determined by testing kit. Free available chlorine: ppm ph: Total Alkalinity: ppm Calcium Hardness: ppm To minimize bleaching, predissolve LATER in a plastic pail with concentration not exceeding 1 kg per 10 litres of water. Always add chemical to water, never water to chemical. Add resulting slurry directly to pool water evenly around the edge. Each week add 100 g per 10,000 litres of pool water. Note: Hot weather, heavy pool usage and rain may require higher dosages and more frequent use g g kg kg BLUEPRINT PRODUCT RESOURCE GUIDE

5 OXY Fast acting, odourless Chlorine-free shock treatment Dissolves quickly OXY should not be used for spring opening or to correct green pools. Use NOW in these instances. Spring Start-Up: 1. Adjust ph to between with PH INCREASER or PH DECREASER. 2. Shock-treat pool water by using NOW. 3. Stabilize pool water to protect chlorine from the destructive forces of sunlight. Stabilize by adding STABILIZE LIQUID just once. OXIDIZE g g kg Regular Daily Care: 1. Test ph and chlorine. ph: but preferably Chlorine: ppm 2. Chlorinate daily with PUCKS CHLORINE or STICKS CHLORINE. Adjust dosage to maintain a chlorine level of ppm. 3. Shock-treat with OXY as follows: Add 1 bag of OXY per 40,000 litres of pool water every 7 days when temperatures are over 25 C. 4. For algae control, add ALGAE BREAK 40 or ALGAE BREAK hours after OXY addition. NOW Powerful oxygen based oxidizer Dissolves quickly Maintain recommended daily levels as determined by testing kit. Free available chlorine: ppm ph: Total Alkalinity: ppm Calcium Hardness: ppm Weekly, add 1 bag per 40,000 litres of pool water by sprinkling product over the surface of the pool. Salt Pool Instructions: Bi-weekly, add 1 bag per 40,000 litres of pool water by sprinkling product over the surface of the pool. Note: Hot weather, heavy pool usage and rain may require higher dosages and more frequent use. Periodic superchlorination of pool water is recommended. Follow label instructions of superchlorination product employed g g BLUEPRINT PRODUCT RESOURCE GUIDE 4

6 RESOLVE OXIDIZE Shock treatment for pool opening and closing Can be used with any sanitizing program (including bromine and salt chlorination) Cold water activated product Rapidly dissolves For oxidizing and/or shock treatment at pool opening and closing, or as a weekly shock treatment. Add 125 g per 10,000 litres of water. With pump and filter running apply RESOLVE very slowly through a clean skimmer that is free of other chemicals or equipment. RESOLVE can alternatively be broadcast over the surface of the pool. If water temperature is less than 20 C brush immediately after application to ensure quick dissolving of product g BLUEPRINT PRODUCT RESOURCE GUIDE

7 ALGAE BREAK 40 Liquid algaecide Controls algae in swimming pool waters 1. Initial dosage for pool water having no visible algae is 100 ml of BLUEPRINT ALGAE BREAK 40 per 10,000 litres of pool water. 2. Weekly maintenance dosage is 35 ml of BLUEPRINT ALGAE BREAK 40 per 10,000 litres of pool water. 3. For pool water having visible algae, superchlorination following label instructions of superchlorination product employed and wait at least 24 hours before adding weekly maintenance dosage. 4. For visible algae, when superchlorination is not employed, add 150 ml of BLUEPRINT ALGAE BREAK 40 per 10,000 litres of pool water. PROTECT mL SPRING & FALL Opening and closing aid for pools Reduces time and effort needed to open or close pools Works great with mesh covers Reduces phosphates and scum line Sanitizer level should be below 5 ppm before adding this product. Specifically formulated for use with all sanitizers. New Pools, Openings and Initial Phosphate Removal: 1. Follow dealer instructions to fill (if new pool) and balance water chemistry. 2. Shake well and use 100 ml per 10,000 litres by adding to the skimmer with the circulation system running. Note: Do not backwash/clean the filter for 48 hours after adding this product. At closing: 1. Add product to a properly balanced pool (with sanitizer level below 5 ppm) at a rate of 100 ml per 10,000 litres. 2. For same day closing, product can be added to the pool water evenly around the edges. Note: This product removes 300 ppb of phosphates from 75,000 litres. For opening: Test phosphate levels weekly and treat as necessary in order to maintain phosphate levels 100 ppb or lower. For closing: Phosphate levels should be 100 ppb or lower for optimal results mL BLUEPRINT PRODUCT RESOURCE GUIDE 6

8 PHOS REMOVE PROTECT Most effective way to remove phosphates Works in the filter (no clouding of the pool water) Reduces phosphates down to near zero No Phosphates - No Problems L This product is designed for use in properly balanced pool water. Specifically formulated for use with all sanitizers. 1. Clean or backwash filter. 2. Determine appropriate dose. See chart below. 3. Shake bottle well prior to application. With circulation pump running, add dose to skimmer. 4. Run the filter for 48 hours continuously without backwashing or cleaning. 5. After 48 hours of filtering, clean/backwash filter. Retest phosphate levels, and if necessary, repeat steps 1-5. Note: If DE filter pressure rises to 10 psi above start-up pressure, turn pump off for 1 minute and then turn back on. If pressure remains high, backwash or rinse for 30 seconds. For D.E. or Cartridge Filters: Do not add more than 1.5 L at a time. If more than 1.5 L is needed to treat, be sure to clean or backwash the filter between treatments. Important: Algae must be treated prior to testing and lowering phosphates. Chlorine must be under 5 ppm before testing phosphates. Phosphate Reading (ppb): 300 or less Quantity of PHOS REMOVE required per 40,000 L: 0.5 L 1 L 1.5 L 2 L PHOS REMOVE EXTRA The lanthanum based formulation effectively and efficiently removes phosphates to reduce pool problems! mL L This product is designed for use in properly balanced pool water. 1. Clean or backwash filter. Make sure DE filters are properly cleaned and charged with DE before adding product. 2. For phosphate levels over 1000 ppb, add 250 ml per 10,000 litres. DO NOT add more than 1.5 L at a time. For DE & Cartridge Filters: Add 250 ml for up to 20,000 litres. 3. Shake bottle well prior to application. With circulation pump running, add the recommended dose to skimmer. 4. Some clouding may occur. Run the pump and filter for 48 hours continuously without backwashing or cleaning. 5. After 48 hours, vacuum to filter. 6. Backwash or clean filter. 7. Retest the phosphate level. Repeat steps 1-6 if necessary. Important: Retest water after each completed treatment. Repeat until phosphate level is below 100 ppb. Note: Algae must be treated prior to testing and treating phosphates. Chlorine must be under 5 ppm before testing for phosphates. Dosage For 946 ml: For phosphate levels over 1000 ppb, add 946 ml (one bottle) per 40,000 litres. DO NOT add more than 1.5 L at a time. For DE & Cartridge Filters: Add 946 ml (one bottle) for up to 80,000 litres. 7 BLUEPRINT PRODUCT RESOURCE GUIDE

9 WEEKLY Highly concentrated Add once per week for easy pool maintenance Naturally based enzymes break down non-living gunk and grime Reduces filter cleanings and scum lines Removes unwanted phosphate contamination This product is designed for use in properly balanced pool water. Specifically formulated for use with all sanitizers. 1. Shake the bottle well as contents may settle. 2. Each week, add 1 capful (120 ml) per 40,000 litres of water down the skimmer with the circulation system running. 3. Proceed with regular pool operation. Note: Sanitizer level should be below 5 ppm before adding this product. PROTECT mL L CONSERVE Invisible barrier that reduces evaporation Saves energy and conserves water Decreases heat loss Specifically formulated for use with all sanitizers. 1. Shake product vigorously. 2. Weekly with circulation system running, add 15 ml per 10,000 litres of pool water in a pool with average depth.* Skimmer application is preferred, however, CONSERVE can be added directly to pool water. It is important that the circulation system be running for either application. * Dosage recommendations are based upon pools with average depth of 5.5 (3 to 8 ). Note: Reapply after heavy bather load due to splash out/drag out, dilution from heavy rain and water loss due to overflow drains. Directions for Areas Affected by Drought or Extreme Conditions: 1. Dose twice per week at a rate of 15 ml per 10,000 litres in a pool with average depth. Pool Dimensions: 16 x x x 40 Quantity of CONSERVE: 90 ml 120 ml 150 ml mL BLUEPRINT PRODUCT RESOURCE GUIDE 8

10 STAIN AND SCALE PROTECT Phosphate and acid free stain and scale prevention Great for new plaster pools and start-ups! Helps protect against calcium and mineral scale buildup Helps protect from iron and copper staining Helps to control scale from forming on salt generator cells, helping maintain optimum performance Specifically formulated for use with all sanitizers and is compatible with all pool surfaces. This product is designed for use in properly balanced pool water. Following dosage chart below, add the recommended initial dosage of STAIN AND SCALE to the pool water evenly around the edge. Note: If water hardness level in existing pool water is above 400 ppm (parts per million), follow recommendations for fresh fill initial dose. Brushing is required. After initial dose, proceed with double the recommended monthly dosage. Do not exceed recommended dose.* *Note: Cationic polymers used in many clarifiers, flocculants and polyquat algaecides should not be dosed to swimming pool water at the same time as metal control products. Cloudy water, precipitation and reduced product effectiveness may result. Wait 24 hours between additions. INITIAL DOSE MAINTENANCE POOL SIZE FRESH FILL EXISTING POOL WATER MONTHLY DOSAGE 40,000 L 2 L 1 L 150 ml 80,000 L 4 L 2 L 295 ml * If preferred, STAIN AND SCALE can be added weekly. Take the recommended monthly dosage and divide it by mL Directions for Use in Salt Water Pools: Add a total of 1 L per 80,000 litres of pool water. This total amount should be divided into two equal doses that are added one week apart. Example: With an 80,000 litre pool, add 0.5 L, wait one week and then add the second dose of 0.5 L. METAL REMOVE Iron-copper-manganese metallic stain remover Controls metal staining Removes iron, copper, or manganese from swimming pool water Important: Do not superchlorinate or shock prior to or during treatment. Apply METAL REMOVE in evening or late afternoon. Avoid superchlorination or shock treatment for one week after application. For Stain Removal: 1. Add 1 L of METAL REMOVE per 80,000 litres of pool water. Add slowly to pool water near returns. 2. Brush stains daily. 3. Repeat treatment for stains not removed after one week of treatment. 4. Metal stains aged into concrete pool surfaces may require acid washing. For Stain Prevention: Each week add 50 ml of METAL REMOVE per 10,000 litres of pool water. If make-up water to pool contains over 0.1 ppm of iron, copper or manganese, double the above dosage mL BLUEPRINT PRODUCT RESOURCE GUIDE

11 ALK INCREASER Prevents ph bounce caused by low total alkalinity Creates an environment in the pool water that helps chlorine do its work effectively Read the entire label before using. 1. Test pool water for total alkalinity level. 2. Compare test results to chart below to determine appropriate amount of ALK INCREASER necessary to make adjustment. 3. Add required amount directly into pool water. 4. Retest and adjust as necessary. DO NOT MIX WITH OTHER CHEMICALS. Total Alkalinity Reading: 20 ppm 30 ppm 40 ppm 50 ppm 60 ppm 70 ppm 80 ppm 90 ppm 100 ppm Quantity of ALK INCREASER required per 10,000 L: 1.6 kg 1.4 kg 1.2 kg 1 kg 800 g 600 g 400 g 200 g None BALANCE kg kg kg kg PH INCREASER Increases the ph of water in swimming pools Maintaining pool water ph in the recommended range is key to proper water balance Read the entire label before using. 1. Test pool water for ph level. 2. Compare test results to chart below to determine appropriate amount of PH INCREASER necessary to make adjustment. 3. Add required amount directly into pool water. 4. Retest and adjust as necessary. DO NOT MIX WITH OTHER CHEMICALS. ph Reading: below above 7.6 Quantity of PH INCREASER required per 10,000 L: 100 g 70 g 50 g 25 g none Add PH DECREASER kg kg BLUEPRINT PRODUCT RESOURCE GUIDE 10

12 PH DECREASER Decreases the ph of water in swimming pools Maintaining pool water ph in the recommended range is key to proper water balance Read the entire label before using. 1. Test pool water for ph level. 2. Compare test results to chart below to determine appropriate amount of PH DECREASER necessary to make adjustment. 3. Add required amount directly into pool water. 4. Retest and adjust as necessary. DO NOT MIX WITH OTHER CHEMICALS. ph Reading: above below 7.4 BALANCE Quantity of PH DECREASER required per 10,000 L: 200 g 150 g 75 g 25 g none Add PH INCREASER kg kg kg CAL INCREASER Raises calcium hardness in swimming pool water Low calcium levels could cause the pool water to become corrosive which may result in damage to the pool surface or equipment Read the entire label before using. 1. Test pool water for calcium hardness level. 2. Compare test results to chart below to determine appropriate amount of CAL INCREASER necessary to make adjustment. 3. Add required amount directly into pool water. Do not pre-dissolve this product as heat is generated when it contacts water. 4. Retest and adjust as necessary. DO NOT MIX WITH OTHER CHEMICALS. Hardness Reading: 0-40 ppm 40 ppm 80 ppm 120 ppm 160 ppm 200 ppm 300 ppm Quantity of CAL INCREASER required per 10,000 L: 3 kg 2.4 kg 1.8 kg 1.2 kg 600 g 0 kg Contact your BLUEPRINT dealer kg kg kg BLUEPRINT PRODUCT RESOURCE GUIDE

13 STABILIZE DRY Used for stabilizing chlorine from UV sunlight loss Read the entire label before using. 1. Test to ensure proper levels: ph Total Alkalinity ppm Chlorine ppm Stabilizer ppm 2. Following the dosage chart below, add the recommended dosage of STABILIZE DRY slowly through the skimmer. 3. Allow 24 hours for total solution and dispersal of STABILIZE DRY to condition the pool water. DO NOT MIX WITH OTHER CHEMICALS. To increase stabilizer by: Quantity of STABILIZE DRY required per 10,000 L: 10 ppm 100 g 20 ppm 25 ppm 200 g 250 g BALANCE g kg STABILIZE LIQUID Protects chlorine from sunlight the instant it is added to pool water Pool friendly ph Will not harm any equipment or pool surfaces 1. Shake well. 2. With circulation pump running, slowly pour STABILIZE LIQUID into pool skimmer or directly into pool water while walking around the edge of the pool. Brush to speed dispersal of the product. 3. Rinse container with pool water and shake to ensure all product is removed from the bottom of the bottle. 4. Pour remaining rinse solution into skimmer or pool. Dosage Tips: 3.78 L of STABILIZE LIQUID raises CYA level by 30 ppm per 40,000 litres. Note: If CYA level is less than 30 ppm, calculate litres of STABILIZE LIQUID needed using the following formula: 30 ml added to 10,000 litres = 1 ppm increase of stabilizer level gal BLUEPRINT PRODUCT RESOURCE GUIDE 12

14 NEUTRALIZE Fast dissolving Reduces excessively high chlorine levels in swimming pool water After heavy shock treatment or when chlorine levels are excessively high, reduce chlorine reading to the recommended level of ppm as follows: 1. Test chlorine level. 2. Compare test results to chart below to determine appropriate amount of NEUTRALIZE necessary to make adjustment. 3. Add required amount of NEUTRALIZE to the pool water evenly around the edge. 4. Circulate pool water for at least 30 minutes before using the pool. BALANCE kg Chlorine level: 1 ppm 5 ppm 10 ppm Quantity of NEUTRALIZE required per 10,000 L: 20 g 100 g 200 g 13 BLUEPRINT PRODUCT RESOURCE GUIDE

15 ALGAE BREAK 60 Liquid algaecide for pools Controls algae in swimming pool waters 1. Initial dosage for pool water having no visible algae is 70 ml of BLUEPRINT ALGAE BREAK 60 per 10,000 litres of pool water. 2. Weekly maintenance dosage is 25 ml of BLUEPRINT ALGAE BREAK 60 per 10,000 litres of pool water. 3. For pool water having visible algae, superchlorinate following label instructions of superchlorination product employed and wait at least 24 hours before adding weekly maintenance dosage. 4. For visible algae, when superchlorination is not employed, add 100 ml of BLUEPRINT ALGAE BREAK 60 per 10,000 litres of pool water mL REMEDY REMEDY Combines powerful naturally based enzymes with a clarifier Powerful pool problem solver that works quickly and efficiently Pool water will sparkle like never before Use to clean up: dead algae, pollen, non-living gunk & grime that builds up on filters, hair products, sunscreens, body oils, lotions and so much more! For optimum results, add product when sanitizer level is below 5 ppm and wait 48 hours to shock the pool. This product is designed for use in properly balanced pool water. Specifically formulated for use with all sanitizers. Dosage: 1 L treats 150,000 litres of pool water. 1 capful (120 ml) treats 20,000 litres of pool water. 1. Add required amount of REMEDY to the pool water evenly around the edge. 2. For ideal results, keep circulation running. 3. Do not shock during this 48 hour time period. Recommendation: If after 2 days water is not clear, repeat process. Important: If water temperature is below 21 C, REMEDY will work more slowly, so allow more time for results.* *Note: Anionic polymers used in many metal and scale control products should not be dosed to swimming pool water at the same time as water clarifiers. Cloudy water, precipitation and reduced product effectiveness may result. Wait 24 hours between additions mL BLUEPRINT PRODUCT RESOURCE GUIDE 14

16 STAIN LIFT REMEDY An all natural way to remove metal staining to pool liners and finishes Quickly removes stubborn stains Compatible with all sanitizing systems g Specifically formulated for use with all sanitizers. Note: Operating the pool for a couple of days without chlorine can create an algae concern. Follow pool dealer s recommendations on steps to take to protect the pool from algae during this metal stain removal clean-up. 1. Balance pool water chemistry before using STAIN LIFT: ph: Total Alkalinity: ppm Calcium Hardness: ppm Phosphates: below 100 ppb Note: Stain removal products work best when the ph is on the lower side of acceptable range (7.2). 2. IMPORTANT: Before starting the metal stain removal or water discolouration clean up (step 4), FILTER ASSIST MUST be added to cartridge and sand filters. DE filters must be properly charged. 3. Lower chlorine level to 1 ppm or less (a high chlorine level or adding oxidizing agents during the clean-up will prevent STAIN LIFT from working as designed). 4. For Surface Staining: If the surface is stained, add 120 g of STAIN LIFT per 10,000 litres as close to the stained area(s) as possible with the pump off overnight. For Water Discolouration: If the entire body of water is discoloured, put the pool on recirculate, add 120 g of STAIN LIFT per 10,000 litres to the pool evenly around the edge. Let the circulation run for one hour. After one hour, shut the pump off and let sit overnight. 5. Before turning the pump back on, brush the pool walls and floor thoroughly. 6. Turn the pump back on and add METAL REMOVE to the pool evenly around the edge at a rate of 125 ml per 10,000 litres. 7. With the pump still on, vacuum the pool walls and floor very thoroughly. 8. After vacuuming, clean filters. Sand filter: backwash for at least 3 minutes and then rinse for 2 minutes. Cartridge filter: clean filter and filter tank thoroughly. DE filter: backwash and recharge with DE. 9. Test and rebalance water. DO NOT SHOCK THE POOL FOR AT LEAST 1 WEEK. Note: If chlorine level is low, add small amounts of chlorine. Do not exceed 2 ppm. For salt generator pools, a granular shock is recommended instead of turning the generator to its boost (superchlorinate) function after the recommended 1 week. 10. Use METAL REMOVE as a weekly maintenance to prevent future metal staining. Apply 50 ml per 10,000 litres once a week. Do not swim until stain procedure is complete and normal chlorine residual is established. 15 BLUEPRINT PRODUCT RESOURCE GUIDE

17 FILTER ASSIST Filter additive - Improves filtration Can be used with sand or cartridge filters Improves filtration producing clear water and longer time cycles between cleanings 1. Clean cartridge or backwash filter. Restart filter operation. 2. Add FILTER ASSIST directly to the skimmer. The water flow will carry FILTER ASSIST to the sand bed or cartridge in your filter. Follow the chart for correct dosage. 3. When maximum pressure recommended by filter manufacturer is reached, backwash the filter or hose off the cartridge. 4. Repeat steps 1 through 3. For Sand Filters: Filter tank diameter: Level cups of FILTER ASSIST recommended: 1 2½ Note: On low head pumps, use about ½ the amount recommended on the chart. For Cartridge Filters: Add approximately 1-2 cups of FILTER ASSIST for each 30 square feet of filter area kg REMEDY PIPE PURGE Helps clean plumbing of non-living organic waste Attacks the root cause of most pool maintenance problems, the buildup of non-living organic waste contamination in plumbing Specifically formulated for use with all sanitizers Great to use before a drain and acid wash or liner change Specifically formulated for use with all sanitizers. For standard pools with up to 2 skimmers, divide the bottle of PIPE PURGE equally between the skimmers. Note: If pool has additional skimmers, more PIPE PURGE is required (1 L per additional skimmer). 1. With circulation pump running and sanitizer level below 5 ppm, add recommended dosage to the skimmer(s). 2. Circulate for 24 hours with pump running continuously. 3. Backwash or clean filter. 4. After the 24 hours, superchlorinate the pool. 5. Proceed with regular pool maintenance L BLUEPRINT PRODUCT RESOURCE GUIDE 16

18 CLEAR REMEDY Natural clarifier made from chitosan the recycled shells of crabs All natural. No mixing required Concentrated 4-in-1 Clarifier Clears cloudy water quickly mL This product is designed for use in properly balanced pool water. Specifically formulated for use with all sanitizers. Standard Dosage Rate: (no remixing required) 15 ml per 10,000 litres of pool water. Cloudy Water Dosage Rate: (no premixing required) 20 ml per 10,000 litres of pool water. 1. Using flip squirt cap, apply CLEAR at the recommended dosage rate across the pool water surface (see side of bottle for measurement marks). 2. Concentrate on deep water areas. 3. Run filter system continuously for at least 6 hours after application. Note: For best results, it is recommended to use this product with an elevated level of chlorine. Weekly Maintenance: To enhance pool water clarity and appearance, treat with CLEAR once a week at the Standard Dosage. For home pools that get heavy use or for commercial pools, treat pool twice a week at the Cloudy Water Dosage. CLEAR ONE SHOT Quickly and effectively clears cloudy water Technologically advanced and highly concentrated pool water clarifier Polishes dull water by removing small suspended particles that filters cannot capture Not ph sensitive, nor will it adversely affect the ph of pool water This product is designed for use in properly balanced pool water. Do not overdose. Specifically formulated for use with all sanitizers. Dosage: 60 ml per 10,000 litres. 1 bottle treats 80,000 litres. 1. Add CLEAR ONE SHOT directly to the pool water evenly around the edge. 2. Concentrate on deep water areas. 3. Run filter system continuously for at least 6 hours after application. *Note: Anionic polymers used in many metal and scale control products should not be dosed to swimming pool water at the same time as water clarifiers. Cloudy water, precipitation and reduced product effectiveness may result. Wait 24 hours between additions mL BLUEPRINT PRODUCT RESOURCE GUIDE

19 COVER CLEAN Removes residue from all pool and spa covers Easy to use and powerful Helps extend cover life Saves time and excessive scrubbing 1. Spread cover out over pool or spa, driveway or yard. 2. Squirt COVER CLEAN on surface of cover and scrub cover with a brush. 3. Rinse with water. 4. Cover may be stored away wet mL REMEDY CLEAN Use on decks, grills and outdoor furniture Great to clean spa shells and covers Cleans even the toughest grease, dirt and grime with ease Won t harm any hard surface Also helps to get rid of strong odours on contact Test small area for colourfastness before use. 1. Apply directly on surface and let product stand for a few minutes. Wipe clean with a sponge and dry. 2. On old stains or built up grease, work into surface with warm water. Wait 5 minutes, wipe clean and then allow to dry mL BLUEPRINT PRODUCT RESOURCE GUIDE 18

20 FILTER CLEAN Highly concentrated naturally based enzyme filter cleaner Removes built up oils, grease, non-living organics and more! Can be used on all pool and spa filter types Improves filter efficiency Allows for longer filter runs For Cartridge Elements and D.E. Grids: 1. Remove cartridge elements or D.E. grids from filter tank and hose off loose material. 2. In a container with litres of water, add one bottle of FILTER CLEAN. 3. Place cartridge elements or D.E. grids in solution and soak for a minimum of 6 hours (preferably overnight). 4. Remove from solution and rinse thoroughly. 5. Clean cartridge elements should be allowed to dry before reinstalling. REMEDY For Sand Filters: 1. Turn pump off. Open pump strainer basket. 2. Pour entire contents of FILTER CLEAN into pump strainer and turn on pump just long enough for liquid to enter filter, then turn off. 3. Replace pump strainer lid. 4. Let sit for a minimum of 6 hours. 5. After the 6 hour period, backwash the filter for 3-5 minutes followed by a 30 second rinse cycle. For Spa Filters: 1. Remove cartridge elements from filter tank and hose off loose material. 2. In a container with litres of water, add 250 ml of FILTER CLEAN. 3. Place cartridge elements in solution and soak for a minimum of 6 hours (preferably overnight). 4. Remove from solution and rinse thoroughly. 5. Clean cartridge elements should be allowed to dry before reinstalling mL BLUEPRINT PRODUCT RESOURCE GUIDE

21 SPRING & FALL KIT Reduces time and effort needed to open or close pools Cleans and protects during the off season Controls metal staining and non-living organic staining Contains a powerful oxygen based oxidizer At closing: 1. Add product to a properly balanced pool (with sanitizer level below 5 ppm) at a rate of 100 ml per 10,000 litres. 2. For same day closing, product can be added to the pool water evenly around the edges. Note: This product removes 300 ppb of phosphates from 75,000 litres. For opening: Test phosphate levels weekly and treat as necessary in order to maintain phosphate levels at 100 ppb or lower. For closing: Phosphate levels should be 100 ppb or lower for optimal results. KIT CONTAINS: ml SPRING AND FALL g NOW ml STAIN AND SCALE SPRING AND FALL Sanitizer level should be below 5 ppm before adding this product. Specifically formulated for use with all sanitizers. New Pools, Openings and Initial Phosphate Removal: 1. Follow dealer instructions to fill (if new pool) and balance water chemistry. 2. Shake well and use 100 ml per 10,000 litres by adding to the skimmer with the circulation system running. Note: Do not backwash/clean the filter for 48 hours after adding this product. NOW Maintain recommended daily levels as determined by testing kit. Free available chlorine: ppm ph: Total Alkalinity: ppm Calcium Hardness: ppm Weekly, add 1 bag per 40,000 litres of pool water by sprinkling product over the surface of the pool. Salt Pool Instructions: Bi-weekly, add 1 bag per 40,000 litres of pool water by sprinkling product over the surface of the pool. Note: Hot weather, heavy pool usage and rain may require higher dosages and more frequent use. Periodic superchlorination of pool water is recommended. Follow label instructions of superchlorination product employed. STAIN AND SCALE Specifically formulated for use with all sanitizers and is compatible with all pool surfaces. This product is designed for use in properly balanced pool water. Following dosage chart below, add the recommended initial dosage of STAIN AND SCALE to the pool water evenly around the edge. Note: If water hardness level in existing pool water is above 400 ppm (parts per million), follow recommendations for fresh fill initial dose. Brushing is required. After initial dose, proceed with double the recommended monthly dosage. Do not exceed recommended dose.* *Note: Cationic polymers used in many clarifiers, flocculants and polyquat algaecides should not be dosed to swimming pool water at the same time as metal control products. Cloudy water, precipitation and reduced product effectiveness may result. Wait 24 hours between additions. KITS INITIAL DOSE MAINTENANCE POOL SIZE FRESH FILL EXISTING POOL WATER MONTHLY DOSAGE 40,000 L 2 L 1 L 150 ml 80,000 L 4 L 2 L 295 ml * If preferred, STAIN AND SCALE can be added weekly. Take the recommended monthly dosage and divide it by 4. Directions for Use in Salt Water Pools: Add a total of 1 L per 80,000 litres of pool water. This total amount should be divided into two equal doses that are added one week apart. Example: With an 80,000 litre pool, add 0.5 L, wait one week and then add the second dose of 0.5 L. SKU# PRODUCT SIZE Kit BLUEPRINT PRODUCT RESOURCE GUIDE 20

22 MAINTAIN 6 KIT KITS Naturally based enzymes break down non-living gunk and grime Controls bacteria and algae in swimming pool waters Contains a powerful oxygen based oxidizer Reduces phosphate contamination KIT CONTAINS: 1-5 kg STICK CHLORINE g NOW 1-2 L WEEKLY STICKS CHLORINE WARNING: Direct Tablet Contact May Cause Bleaching of Vinyl or Painted Pool Surfaces. Automatic Feeding Devices Employing These Tablets Must be Totally Free from Traces of other Pool Sanitizers To Avoid the Probability of an Explosion. Maintain recommended daily levels as determined by testing kit. Free available chlorine: ppm ph: Total Alkalinity: ppm Calcium Hardness: ppm For outdoor pools, chlorine residuals can be protected from destruction by the sun s rays by adding 300 g of STICKS CHLORINE per 10,000 litres of pool water to yield the required initial concentration of 30 ppm. If using an automatic chlorinator, fill the chamber[s] with tablets and adjust flow rate, according to manufacturer s recommendations, to maintain proper chlorine residual. Adding tablets to the pool s skimmer basket is an alternative chlorine feed method. Daily usage should approximate 25 g of STICKS CHLORINE per 10,000 litres of pool water. Note: Hot weather, heavy pool usage and rain may require higher usage rates to maintain proper chlorine residuals. Periodic superchlorination of pool water is recommended. Follow label instructions of superchlorination product being employed. STICKS CHLORINE contains stabilizer which can accumulate in pool water. Keep stabilizer within the range of ppm by dilution with fresh water. NOW Maintain recommended daily levels as determined by testing kit. Free available chlorine: ppm ph: Total Alkalinity: ppm Calcium Hardness: ppm Weekly, add 1 bag per 40,000 litres of pool water by sprinkling product over the surface of the pool. Salt Pool Instructions: Bi-weekly, add 1 bag per 40,000 litres of pool water by sprinkling product over the surface of the pool. Note: Hot weather, heavy pool usage and rain may require higher dosages and more frequent use. Periodic superchlorination of pool water is recommended. Follow label instructions of superchlorination product employed. WEEKLY This product is designed for use in properly balanced pool water. Specifically formulated for use with all sanitizers. 1. Shake the bottle well as contents may settle. 2. Each week, add 1 capful (120 ml) per 40,000 litres of water down the skimmer with the circulation system running. 3. Proceed with regular pool operation. Note: Sanitizer level should be below 5 ppm before adding this product. SKU# PRODUCT SIZE Kit 21 BLUEPRINT PRODUCT RESOURCE GUIDE

23 MAINTAIN 6 SALT KIT Naturally based enzymes break down non-living gunk and grime Controls metal staining and non-living organic staining Contains a powerful oxygen based oxidizer Reduces phosphate contamination KIT CONTAINS: g NOW 1-2 L WEEKLY ml STAIN AND SCALE NOW Maintain recommended daily levels as determined by testing kit. Free available chlorine: ppm ph: Total Alkalinity: ppm Calcium Hardness: ppm Weekly, add 1 bag per 40,000 litres of pool water by sprinkling product over the surface of the pool. Salt Pool Instructions: Bi-weekly, add 1 bag per 40,000 litres of pool water by sprinkling product over the surface of the pool. Note: Hot weather, heavy pool usage and rain may require higher dosages and more frequent use. Periodic superchlorination of pool water is recommended. Follow label instructions of superchlorination product employed. WEEKLY This product is designed for use in properly balanced pool water. Specifically formulated for use with all sanitizers. 1. Shake the bottle well as contents may settle. 2. Each week, add 1 capful (120 ml) per 40,000 litres of water down the skimmer with the circulation system running. 3. Proceed with regular pool operation. Note: Sanitizer level should be below 5 ppm before adding this product. STAIN AND SCALE Specifically formulated for use with all sanitizers and is compatible with all pool surfaces. This product is designed for use in properly balanced pool water. Following dosage chart below, add the recommended initial dosage of STAIN AND SCALE to the pool water evenly around the edge. Note: If water hardness level in existing pool water is above 400 ppm (parts per million), follow recommendations for fresh fill initial dose. Brushing is required. After initial dose, proceed with double the recommended monthly dosage. Do not exceed recommended dose.* *Note: Cationic polymers used in many clarifiers, flocculants and polyquat algaecides should not be dosed to swimming pool water at the same time as metal control products. Cloudy water, precipitation and reduced product effectiveness may result. Wait 24 hours between additions. KITS INITIAL DOSE MAINTENANCE POOL SIZE FRESH FILL EXISTING POOL WATER MONTHLY DOSAGE 40,000 L 2 L 1 L 150 ml 80,000 L 4 L 2 L 295 ml * If preferred, STAIN AND SCALE can be added weekly. Take the recommended monthly dosage and divide it by 4. Directions for Use in Salt Water Pools: Add a total of 1 L per 80,000 litres of pool water. This total amount should be divided into two equal doses that are added one week apart. Example: With an 80,000 litre pool, add 0.5 L, wait one week and then add the second dose of 0.5 L. SKU# PRODUCT SIZE Kit BLUEPRINT PRODUCT RESOURCE GUIDE 22

24

25 TABLE OF CONTENTS SOAK TABS BROMINE 25 SOAK ALK INCREASER 30 SOAK PH INCREASER 30 SOAK PH DECREASER 31 SOAK CAL INCREASER 31 SOAK NOW 26 SOAK SOON BROMINE 26 SOAK SOON CHLORINE 27 SOAK CLEAR 32 SOAK DEFOAM 32 SOAK PIPE PURGE 33 SOAK WEEKLY 28 SOAK PHOS REMOVE 28 SOAK STAIN AND SCALE 29

26 SOAK TABS BROMINE Stabilized chlorinating tablets Controls bacteria and algae in swimming pool waters DO NOT contaminate irrigation or drinking water supplies or aquatic habitats by cleaning of equipment or disposal of wastes. 1. Maintain recommended daily levels as determined by testing kit. Free available bromine: ppm ph: Total Alkalinity: ppm Calcium Hardness: ppm 2. If using an automatic feeding device, fill the chamber(s) with the tablets and adjust flow rate, according to manufacturer s recommendations, to maintain proper bromine residual. Adding tablets to the spa s skimmer basket is an alternative bromine feed method. Daily usage should approximate 5 g of SOAK TABS BROMINE per 1,000 litres of spa water. NOTE: Heavy spa usage, and higher temperatures may require higher usage rates to maintain proper bromine residuals. 3. Periodic superchlorination of spa water is recommended. Follow label instructions of superchlorination products being employed. NOTE: Persistent foam formation, turbid, or malodorous water are indicators of inadequate sanitizer levels. To correct such conditions, superchlorinate spa water by adding superchlorination product. Maintain circulation at least 30 minutes and wait 4 hours before using. For proper sanitation, spa must be completely drained periodically. The number of days between COMPLETE SPA DRAINAGE is equal to the volume of spa water in litres, divided by 10 times the maximum number of daily users. Refill the spa with water and repeat DIRECTIONS FOR USE. Maximum spa water usage temperature is 40 C. Duration in spa water should not exceed 15 minutes. SOAK SANITIZE g kg BLUEPRINT PRODUCT RESOURCE GUIDE

27 SOAK NOW Powerful oxygen based oxidizer Compatible with spas using chlorine or bromine products Dissolves quickly Read the entire label before using. Initial Treatment: Add 50 g per 1,000 litres of spa water. Regular Treatment: After each time the spa is used add 22 g per 1,000 litres of water. Add 22 g per 1,000 litres each week the spa is not being used. Add product with circulating pump running, continue circulating for at least 30 minutes. Turn the jets on and off once or twice after adding the product to improve the treatment g kg SOAK SOON BROMINE Gentle on spa surfaces Dissolves quickly Read the entire label before using. Initial Treatment: Add 25 g per 1,000 litres of spa water. Regular Treatment: Add 25 g per 1,000 litres each week. Add product with circulating pump running, continue circulating for at least 30 minutes. Turn the jets on and off once or twice after adding the product to improve the treatment. SOAK OXIDIZE g kg BLUEPRINT PRODUCT RESOURCE GUIDE 26

28 SOAK SOON CHLORINE Clears cloudy or dull water Can be used with any sanitizer program including bromine and salt chlorination Read the entire label before using. With pump and filter running, add 12 g per 1,000 litres of spa water slowly through a clean skimmer that is free of other chemicals or equipment. SOAK SOON CHLORINE can alternatively be broadcast over the surface of the spa when water temperature is above 27 C g kg SOAK OXIDIZE 27 BLUEPRINT PRODUCT RESOURCE GUIDE

29 SOAK WEEKLY Add once per week for easy spa maintenance Concentrated blend of naturally based enzymes with phosphate remover Works as a continuous cartridge filter cleaner Controls waterline rings and reduces cloudy or unpleasant smelling water This product is designed for use in properly balanced spa water. Weekly with the filtration system running, add 10 ml per 100 litres directly to the spa water. 1 large cap (120 ml) treats 1,200 litres. Note: Sanitizer level should be below 5 ppm before adding this product mL L SOAK PHOS REMOVE Most effective way to remove phosphates Helps reduce higher phosphate levels Add weekly to help maintain consistently low phosphate levels This product is designed for use in properly balanced spa water. Initial Treatment and After Fresh Fill: With the circulation system running, add 1 bottle (473 ml) per 1,500 litres of spa water. Treatment will remove up to 300 ppb of phosphates in 1,500 litres of spa water. Temporary turbidity may be experienced. SOAK PROTECT mL BLUEPRINT PRODUCT RESOURCE GUIDE 28

30 SOAK STAIN AND SCALE Helps control calcium and mineral scale buildup Phosphate and acid free formula Helps protects from iron and copper staining Helps to control scale from forming on salt generator cells, helping maintain optimum performance This product is designed for use in properly balanced spa water. Initial Treatment of Fresh Fill: Add 300 ml per 1,000 litres directly to spa water. Weekly Maintenance: Add 40 ml per 1,000 litres directly to spa water. Note: If water hardness level is above 400 ppm, double the weekly maintenance dose. Do not exceed recommended dose.* *Note: Cationic polymers used in many clarifiers, flocculants and polyquat algaecides should not be dosed to spa water at the same time as metal control products. Cloudy water, precipitation and reduced product effectiveness may result. Wait 24 hours between additions. SOAK mL mL PROTECT 29 BLUEPRINT PRODUCT RESOURCE GUIDE

31 SOAK ALK INCREASER Increases the alkalinity of spa water A result of the buffering effect of total alkalinity is ph, bather comfort, water balance, and clarity are more easily maintained Read the entire label before using. 1. Test spa water for total alkalinity level. 2. Compare test results to chart below to determine appropriate amount of SOAK ALK INCREASER necessary to make adjustment. 3. With spa circulating pump on high speed add required amount directly into spa water. 4. Continue circulating water a minimum of 20 minutes. 5. Retest and adjust as necessary. DO NOT MIX WITH OTHER CHEMICALS g SOAK PH INCREASER Increases the ph of spa water Maintaining spa water ph in the recommended range is key to proper water balance Read the entire label before using. 1. Test spa water for ph level. 2. Compare ph test results to chart below to determine appropriate amount of SOAK PH INCREASER necessary to make adjustment. 3. With the spa not in use and circulation pump operating, add required amount directly into spa water. 4. Continue circulating water a minimum of 30 minutes. 5. Retest and adjust if necessary. DO NOT MIX WITH OTHER CHEMICALS. SOAK g BALANCE BLUEPRINT PRODUCT RESOURCE GUIDE 30

32 SOAK PH DECREASER Decreases the ph of spa water When ph is too high (above 7.6), water becomes uncomfortable to bathers, sanitizers lose their efficiency, water may become cloudy and scale forms more readily Read the entire label before using. 1. Test spa water for ph level. 2. Compare ph test results to chart below to determine appropriate amount of SOAK PH DECREASER necessary to make adjustment. 3. With the spa not in use and circulation pump operating, add required amount directly into spa water. 4. Continue circulating water a minimum of 30 minutes. 5. Retest and adjust if necessary. DO NOT MIX WITH OTHER CHEMICALS g SOAK SOAK CAL INCREASER Increases the calcium hardness of spa water Low calcium hardness levels could cause the spa water to be corrosive which may result in damage to the spa surface or equipment Read the entire label before using. 1. Test spa water for calcium hardness level. 2. Compare test results to chart below to determine appropriate amount of SOAK CAL INCREASER necessary to make adjustment. 3. With the spa not in use and circulation pump operating, add required amount directly into spa water. 4. Continue circulating water a minimum of 20 minutes. Do not pre-dissolve this treatment as heat is generated when it contacts water. 5. Retest and adjust if necessary. DO NOT MIX WITH OTHER CHEMICALS. BALANCE g BLUEPRINT PRODUCT RESOURCE GUIDE

33 SOAK CLEAR Natural clarifier made from chitosan - the recycled shells of crabs Use to effectively and quickly clear problem water or to polish dull water by removing small suspended particles. Compatible with all sanitizing systems and is environmentally safe This product is designed for use in properly balanced spa water. Standard Dosage Rate: (No premixing required) 40 ml per 1,000 litres of spa water. Cloudy Water Dosage Rate: (No premixing required) 160 ml per 1,000 litres of spa water. 1. Using flip squirt cap, apply SOAK CLEAR at the recommended dosage rate across the spa water surface. 2. Concentrate on deep water areas. 3. Run filter system continuously for at least 6 hours after application. Note: For best results, it is recommended to use this product with an elevated level of chlorine. Weekly Maintenance: To enhance spa water clarity and appearance, treat with SOAK CLEAR once a week at the Standard Dosage. For home spas that get heavy use or for commercial spas, treat spa twice a week at the Cloudy Water Dosage mL SOAK DEFOAM Quickly eliminates foam in spas Specifically formulated for spas and therapeutic pools This product is designed for use in properly balanced spa water. 1. Shake well before each use. 2. With circulation system running, add approximately 15 ml of product directly to spa water. 3. Repeat as necessary. SOAK mL BLUEPRINT PRODUCT RESOURCE GUIDE 32 REMEDY

34 SOAK PIPE PURGE Helps clean spa plumbing of non-living organic waste Attacks the root cause of most spa maintenance problems - the buildup of non-living organic waste contamination Spas: 1. Remove and clean the cartridge elements. 2. With spa water temperature at 35 C or higher and circulation running, add entire contents of SOAK PIPE PURGE bottle to spa water. 3. Run jets for a minimum of 5 minutes. Note: Please leave air controls off during the circulation process. Some foaming should be expected. 4. Maintain water temperature at 35 C and allow spa to circulate overnight with jets off. 5. Drain and rinse/clean out the surfaces of the spa. Refill the spa with water and install the filter elements. 6. Proceed with normal spa maintenance. For Jetted Tubs: 1. Fill tub with hot water 1 above the jets. 2. Add 1/2 bottle of SOAK PIPE PURGE. 3. Turn jets on for 5 minutes (some foaming will occur). 4. Turn jets off and let sit for at least 5 hours. 5. Turn jets on to flush the system. 6. Drain tub & clean surface as needed. SOAK mL REMEDY 33 BLUEPRINT PRODUCT RESOURCE GUIDE