HALYARD EXITS, CLEATS, CLUTCHES, WINCH PADS, HANDLE POCKET
|
|
- Kathlyn Curtis
- 5 years ago
- Views:
Transcription
1 HALYARD EXITS, CLEATS, CLUTCHES, WINCH PADS, HANDLE POCKET 1(6) General CNC-milled masts Cut out using templates Cut out without using templates Assembly Assembly clutch spinnlock ZS/1214 Check point General This instruction describes how to locate and fit slots, cleats, winch pads, rope clutches and handle pockets on mast sections C156-C365 and F156-F406. On F-sections the access and grease holes should also be cut out at this stage. See PHB For reference see MB M 1530:1 MB M 1630 MB M 1660 MB M 1690 P (Layouts, conventional, furling) (Winch pad) (Winch, handle, pocket) (Cleat) C-sections PS drawing F-section PS drawing C 156 PS 584, 583, 534 F 176 PS 543 C 175 PS 585, 586, 535 F 194 PS 544 C 193 PS 587, 588, 536 F 212 PS 545 C 211 PS 537 F 228 PS 546 C 227 PS 538 F 246 PS 547 C 246 PS 539 F 265 PS 548 C 265 PS 540 F 286 PS 549 C 286 PS 541 F 305 PS 550 C 304 PS 542 F324 PS 666 C321 PS 695 F370 PS 693 C365 PS 696 F406 Adapted to mast Table 1. CNC-milled masts 1. Turn the mast with B-line facing up. 2. Clean the mast from oil and metal chips. 3. Grind the access holes on F-sections. M 4. Grind the Ø39,1 on F-sections. C 5. Tap the holes for fastening clutches. If M8; enlarge holes to Ø6,5 before tapping. (see table 5, page 4 ) 6. If the mast is equipped with winch pad(s) and winch handle pocket(s), use them as templates for drilling. Mark the location acc. to PS-drawing or mast specification. Reference hole for winch pads: upper aft hole. Reference hole for handle pocket: upper hole. 7. Turn the mast 180 and repeat steps 1-6
2 2(6) 8. For attachment of fittings see section Assembly. Cut-out using templates 1. Find the right template for the mast being built, see table Turn the mast with the B-line facing up. 3. On keel stepped masts, mark the height of top of mast coat. 4. Position the template aligned with end of extrusion (for keel stepped masts; aligned with mast coat height mark). If double templates; place the upper template against the lower. 5. Drill holes for all functions specified in the mast specification. 6. Remove template(s) and enlarge holes acc. to table 3, 4 and Draw tangent straight lines to mark for slot fitting cut-out. 8. Cut along the inside of the lines with a tenon saw. The cut-outs should not be wider than the diameter of the holes. 9. Grind the edges on the inside of the slot fitting cut-outs. C 10. Tap holes for clutches and cleats. (See table 4 and 5) 11. Remove burrs and degrease the mast surface before mounting fittings. 12. For attachment of fittings see section Assembly. 13. Turn the mast 180 and repeat steps 1-12 Section Cleat Port Cleat Stb Slot Port Slot Stb C 156 C 306 C 305 C 308 C307 C 175 C 406 C 405 C 408 C 407 C 193 C 506 C 505 C 508 C 507 C 211 C 606 C 605 C 608 C 607 C 227 C 706 C 705 C 708 C 707 C 246 C 806 C 805 C 808 C 807 C 265 C 906 C 905 C 908 C 907 C 286 C 1006 C 1005 C 1008 C 1007 C 304 C 1106 C 1105 C 1108 C 1107 C 321 C 365 F 176 F 194 F 212 F 606 F 605 F 608 F 607 F 228 F 706 F 705 F 708 F 709 F 246 F 806 F 805 F 808 F 807 F 265 F 906 F 905 F 908 F 907 F 286 F 305 F 324 F 370 F 406 Table 2
3 3(6) Cut-out without using templates 1. Find the relevant PS drawing acc. to table If the mast is keel stepped, mark the height of the mast coat upper edge and use this mark as base line. If the mast is deck stepped, end of extrusion is to be used as base line. 3. Turn the mast with the B-line up and attach a measure tape at the end of the mast section or at the mast coat upper edge mark. Fasten the measure tape about four metres up the mast. 4. Mark the height s for all specified slots fittings, cleats, clutches, winch pads, and handle pocket(s). Slots and cleats are marked with a number in the mast specification which refers to the PS-drawing. 5. When the height s are marked, mark the side s measured from B-line. 6. Draw a line parallel to the B-line through each mark. 7. Mark all remaining holes acc to table 2, 3 & Use the winch pad as template and mark all holes with a pencil. Reference: upper aft hole. 9. Use the winch handle pocket as a template and mark the holes with a pencil. Reference: upper hole. 10. Pre-drill with a Ø4,9 mm drill bit in all marks. 11. Enlarge the holes acc. to table 3 (slots), table 4 (cleats), table 5 (clutches). Winch pads and handle pockets: Ø6,5 mm. 12. Draw tangent straight lines to mark for slot fitting cut-out. 13. Cut along the inside of the lines with a tenon saw. The cut-outs should not be wider than the diameter of the hole. 14. Grind the edges on the inside of the slot fitting cut-outs. C 15. Tap holes for clutches and cleats, when stated. (See table 4 and 5) 16. Remove burrs and degrease the mast surface before adding fittings. 17. For attachment of fittings see section Assembly. 18. Turn the mast 180 and repeat steps 1-17.
4 4(6) Ø A Slots Part No Size A (hole saw) B Medium Small Large X-large B Table 3. Cleats Part No Size ØA B mm 4,9 mm 20 Comp mm 6,5 mm 40 Comp mm 6,5 mm 45 Comp mm 6,5 mm mm 6,5 mm 27x mm 4,9 mm M6 33 (Polished) mm (Polished) 6,5 mm M8 50 ØA B ØA Ø Table 4. Clutches (Stopper) & jammers Part No Size ØA (screw) B Lew. Ø6-Ø8 Ø4,9 mm M6? Lew. Sing. Ø8-Ø10 Ø6,5 mm M Lew. Sing. Ø10-Ø12 Ø6,5 mm M Lew. Sing. Ø12-Ø-14 Ø6,5 mm M Lew. Sing. Ø14-Ø16 Ø6,5 mm M Spinlock. XCS0814 Ø6,5 mm M Spinlock. XTS0814 Ø6,5 mm M Spinlock. XX0812S Ø4,9 mm M Spinlock. XAS0612/1 Ø4,9 mm M Spinlock ZS 1214 See Haly. Lock 30x150 (WIRE 8 mm Ø6,5 mm M8 122 Table 5. ØA B
5 5(6) Assembly 1. If necessary, compress the slot fitting hook, as shown in pic. 1, using a pair of pliers, to achieve a tight fit around the mast wall. See pic Fit the slot fittings into the slots. Check that the fittings are mounted the right way up, and push/knock upwards so that the slot fitting upper end is fixed. See pic Drill Ø4,9 through the slot fitting hole while holding it firmly pushed up. Fasten with rivet. 4. Fasten all cleats, winch pads, and handle pocket(s) with fasteners acc. to mast spec. Use rivet pistol with long nozzle to rivet cleats. 5. Punch out all mandrel heads. 6. If function labels are specified, clean mast with alcohol aft of the slot fittings first and place the function labels parallel to the slot fittings as shown in pic Wash with alcohol and place the Seldén logo 100 mm above the uppermost slot fitting, see pic 2. (One Seldén logo on each side at the same level.) 8. Wash with alcohol and place the cable marking label ~50 mm above end of extrusion on the starboard side, see pic On fractional masts, wash with alcohol and place the jib halyard over-tensioning label on the same side and at the same height as the jib halyard slot fitting or stopper, see pic Turn the mast 180 and repeat steps Pic 1 Pic 3 Aft Fwd SLOT FITTING Pic PIC 55. CONTACT POINT Function label ~ 100 Pic 4 Pic 2
6 6(6) Assembly Clutch spinlock ZS/1214 For reference see Decide height, side measure for the clutch and make a mark. 2. Draw a line parallel to the B-line through the mark. 3. Fit the mounting plate with the centre mark on the line with the front pointing to the winch, see pic Mark the 8 holes for MFT 6x20 screws on the mast. 5. Drill Ø 4,9 mm in the marks and tap for M6. 6. Mount the clutch Spinlock ZS/1214 on the mounting plate ( ) by using four screws MFT 8x20 from under side mounting plate and into the clutch. 7. Apply Loctite 639 on the screw threads. 8. Fasten spinlock ZS/1214 with mounting plate on the mast with 8 M6x20 screws, see pic Use Schneidmittel or similar on the screw threads. Pic 4. Pic 5. Check points Check that insulator is fitted between winch pad and winch. Check that access and grease holes are cut out.
SPINNAKER POLE TRACK AND GUIDE CONSOLE
1(5) SPINNAKER POLE TRACK AND GUIDE CONSOLE General Assembly single tracks Cut-out for spreader bracket Fitting single guide console Assembly single tracks with bedding Cut-out for spreader bracket Fitting
More informationKeel-stepped and deck-stepped masts,
Keel-stepped and deck-stepped masts, C-sections and F-sections The T-base and deck ring systems are made to fit both Seldén s conventional mast sections and their matching furling sections. They are also
More informationCarbo Racing Foil Instruction Manual Unit 0, 1, 2, 3
Carbo Racing Foil Instruction Manual Unit 0, 1, 2, 3 WARNING!: Strictly follow all instructions to avoid an accident, damage to your vessel, personal injury or death. See www.harken.com/manuals for additional
More informationFitting Instructions for Single Line Mainsail Reefing System For Yachts Up To 9m (30ft) - Part No
Fitting Instructions for Single Line Mainsail Reefing System For Yachts Up To 9m (30ft) - Part No. 41 130 This single line reefing kit allows reefing control lines to be led aft to the safety of the cockpit.
More informationCOASTAL IN-BOOM FURLING SYSTEM. Installation Manual
COASTAL IN-BOOM FURLING SYSTEM Installation Manual 1 TABLE OF CONTENTS Page Number 3. Disclaimer 4. Components packing list & required tools 5. Gooseneck bracket location 6. Installation sail track 7.
More informationFitting Instructions For Slab Reefing Kit Part No For Yachts Up To 8.5m (2 Reefing Points)
Fitting Instructions For Slab Reefing Kit Part No 41483 For Yachts Up To 8.5m (2 Reefing Points) This system makes reefing your mainsail a quick and easy operation. Just lower the mainsail just below a
More informationFITTING INSTRUCTIONS FOR CASCADE LIGHTWEIGHT LAZY JACK KITS For yachts up to 10.5m (35ft) Part No
FITTING INSTRUCTIONS FOR CASCADE LIGHTWEIGHT LAZY JACK KITS For yachts up to 10.5m (35ft) Part No. 41 143 The lightweight Lazy Jack System allows the mainsail to be easily reefed or stowed in all weather
More information2012-June-12 SECOND DRAFT Hobie Getaway Spinnaker Installation Instructions
SECTION A: INTRODUCTION This unofficial set of installation instructions was written for a 2009 Hobie Getaway, using a 2012 Hobie Spinnaker Kit 20999020. Note from the Author: I had never seen this kit
More informationE Manual Self tacking system 30
597-205-E 2015-12-09 Manual Self tacking system 30 1 Self tacking system 30, 443-200-10 A self-tacking jib makes life on board a lot easier, in particular for shorthanded crews. The jib sheet is led to
More informationForestay fittings and halyard routing
Festay fittings and halyard routing Cutter stay on masthead rigs On fractional rigs the festay fitting is either fitted directly on to the mast combined with the halyard box (Seldén combi boxes). The festay
More informationEssential Rig Tuning Guide The Ins and Outs of tuning your mast.
Essential Rig Tuning Guide The Ins and Outs of tuning your mast. Tuning Your Rig The main goal in tuning your mast is to achieve a spar that s straight. By doing this it will help you gain control of sail
More informationSpinnaker pole kit, dip pole
595-785-E 2007-01-12 Spinnaker pole kit, dip pole Assembly instructions 96/96 and 99/99 72/72 and 84/84 2 Required tools: Hacksaw Hammer Mandrel (max. diam. ø3,5mm) Drill Drillbit ø6,5mm Rivet gun File
More informationASSEMBLY MANUAL HOBIE CATSY
ASSEMBLY MANUAL HOBIE CATSY HOBIE CAT EUROPE ZI Toulon Est, BP 50 8078 Toulon cedex 9, France Tel : + (0)9 08 78 78 - Fax : + (0)9 08 99 Email : hobiecat@hobie-cat.net - http://www.hobie-cat.net ASSEMBLY
More informationWeta Basic Rigging Guide
Weta Basic Rigging Guide A quick reference guide of how to rig your Weta, with some tips to make rigging quick and easy! For a more indepth guide see our Weta Manual under Weta Owners on the website. 1.
More informationManual for FURLING MAST ELECTRIC E
Manual for FURLING MAST ELECTRIC 595-193-E 2014-07-04 Contents Contents... 2 INTRODUCTION... 4 About the Manual... 4 1 SYSTEM DESCRIPTION... 5 1.1 General Description... 5 1.2 The Furling System... 6 1.3
More informationCamRT Sun Top Bimini Installation Instructions
CamRT Sun Top Bimini Installation Instructions C910-07 & C910-08 Rev. 16-Jun-15 Information: info@roswellglobal.com Warranty: warranty@roswellglobal.com Questions? Please call us at (31) 638-1331 Setup:
More informationBelow are the instructions to build a roller-furling unit for under $10. Read the entire process before beginning the project.
Greg Cowens' $10 PVC Roller Reefing for CP-16's by Greg Cowen Below are the instructions to build a roller-furling unit for under $10. Read the entire process before beginning the project. Materials: 2
More informationTable of content Introduction 5 1. Part 1. Assembly Tools needed for Assembly Glossary Hulls Mounting the beams 7
Table of content Introduction 5 1. Part 1. Assembly 6 1.1. Tools needed for Assembly 6 1.2. Glossary 6 1.3. Hulls 7 1.3.1. Mounting the beams 7 1.3.2. Fixing the mast rotation cleats 8 1.3.3. Placing the
More informationRUDDER KIT INSTRUCTIONS
A I N S T R U C T I O N S RUDDER KIT INSTRUCTIONS TARPON 0/40/60/60i The Tarpon series is designed as a high performance sit-on-top kayak tailored for the sport paddler. Our rudder system is designed to
More informationFDR CHRYSLER 16' CATAMARAN (MUSKETEER) The initial rigging of a sailboat is not difficult, but if the boat is strange
Page of 6 Revised 2/0/76 RIGGING INSTRUCTIONS FDR CHRYSLER 6' CATAMARAN (MUSKETEER) The initial rigging of a sailboat is not difficult, but if the boat is strange to the new owner, or the new owner is
More informationDepth sensor. Product reference : REV 1. USER GUIDE and INSTALLATION GUIDE. nke Sailing competition
Depth sensor Product reference : 90-60-456 REV 1 USER GUIDE and INSTALLATION GUIDE nke Sailing competition Z.I. Kerandré Rue Gutenberg 56700 HENNEBONT- FRANCE http://www.nke.fr After sale service n 33
More informationCentriFlow Meter Integrated Air Entrainment System
CentriFlow Meter Integrated Air Entrainment System INSTALLATION & OPERATION MANUAL January 2004 Revision 021-4 EASTERN INSTRUMENTS 416 LANDMARK DR. WILMINGTON, NC 28412 910-392-2490 Fax: 910-392-2123 website:
More informationMANUAL REEFING SYSTEMS
MANUAL REEFING SYSTEMS Reliability > Performance > Robustness PROFURL offers a comprehensive range of manual headsail furlers. With its Cruising and Racing models, PROFURL is able to match the expectations
More informationULTIMATE 12 RUDDER INSTALLATION INSTRUCTIONS
ULTIMATE 12 RUDDER INSTALLATION INSTRUCTIONS TOOLS NEEDED: DRILL ¼ DRILL BIT ¾ HOLE SAW 3/16 DRILL BIT PHILLIPS HEAD SCREWDRIVER 7/16 WRENCH HEAT SOURCE: PROPANE TORCH, LIGHTER OR HOT AIR GUN WIRE CUTTER
More informationInstallation Instructions for Reef-Rite Furling Systems
Installation Instructions for Reef-Rite Furling Systems Congratulations on the purchase of your new Reef-Rite Furling System! It has been constructed with great care from the finest materials available,
More informationF-1279-R UPPER RIGHT SKIN F-1280-R RIGHT SIDE SKIN F-1281-R LOWER RIGHT SKIN F-1208-R FUSELAGE FRAME
F-1282-R BOTTOM RIGHT SKIN F-1283C J-STIFFENER F-1278 TOP SKIN F-00009-L ADAHRS BRACKET F-00009-R ADAHRS BRACKET F-1279-R UPPER RIGHT SKIN F-1280-R RIGHT SIDE SKIN SECTION 10: TAILCONE F-1279-L UPPER LEFT
More informationPre-Paint>Fuselage>Empennage>Fit vertical tail fin. Objectives of this task: Materials and equipment required: Fit the spar extender
Pre-Paint>Fuselage>Empennage>Fit vertical tail fin Objectives of this task: To fit the vertical tail fin to the fuselage, including fitting the static probe, static tube, optional strobe light wiring and
More informationQuikVang. The Original High-Performance Vang INSTALLATION AND OPERATING INSTRUCTIONS MODEL D-30 MODEL D-40
QuikVang The Original High-Performance Vang INSTALLATION AND OPERATING INSTRUCTIONS MODEL D-30 MODEL D-40 33 Broadcommon Road, Bristol, RI 02809 USA T: 401.253.4858 F: 401.253.2552 www.hallspars.com 1
More informationRUDDER KIT INSTRUCTIONS
C I N S T R U C T I O N S RUDDER KIT INSTRUCTIONS PAMLICOS-0,0,T, T, 60T, Excel Rotomolded Pamlico 0, 0, T, T, 60T, Excel The addition of a rudder to a kayak results in additional control and efficiency,
More informationM32 CATAMARAN ASSEMBLY MANUAL
M32 CATAMARAN ASSEMBLY MANUAL 1 M32 CATAMARAN ASSEMBLY MANUAL MANUAL SUMMARY M32 ASSEMBLY Parts and tools Instructions MAST PLATFORM Parts and tools Instructions MAST STEPPING Instructions MAIN HALYARD
More informationConstitution Instructions
Constitution Instructions This kit will build a 1:48 scale hull for the USS Constitution frigate. The kit contains the following parts. 1/8 deck with laser etched deck lines 1/8 railing Ribs Center keel
More informationTelescopic winch handle Speedfriend"
Winch handles, jib furlers JIB FURLERS - WINCH HANDLES - SPREADER COVERS 57 Floating winch handles Floating universal size winch handles Fitted with "Lock In" winch system; universal size for any winch;
More information(PLEASE CONTACT YOUR LOCAL DEALER or CUSTOMER SERVICE FOR WARRANTY INFORMATION)
RUDDER KIT SOLO KAYAKS IMPORTANT: Tandem models will require the Wildy Supplemental kit in addition to this kit. The Supplemental kit provides extension straps and extra footbraces that allow rudder positioning
More informationFar East Boat Optimist Rigging Instructions
Far East Boat Optimist Rigging Instructions These instructions are written specifically for Far East Boats Championship and Racing Optimist. Parts of the Optimist PAGE 1 Sprit Wind Indicator Sail Mast
More informationTable of content Introduction 5 1. Part 1. Assembly 6 1.1. Tools needed for Assembly 6 1.2. Glossary 6 1.3. Hulls 7 1.3.1. Mounting the beams 7 1.3.2. Fixing the mast rotation cleats 8 1.3.3. Mounting
More informationSECTION 10iS: TAILCONE
VAN'S AIRCRAFT, INC. F-1282-R BOTTOM RIGHT SKIN F-1283C J-STIFFENER F-1278 TOP SKIN F-00009-L ADAHRS BRACKET F-00009-R ADAHRS BRACKET F-1279-R UPPER RIGHT SKIN F-1280-R RIGHT SIDE SKIN SECTION 10iS: TAILCONE
More informationTube-on-tube to wire luff conversion by Rey Garza
Tube-on-tube to wire luff conversion by Rey Garza I recommend changing from the old tube-on-tube furling system to the wire luff system. I did it and I think that the boat is now easier to rig, plus I
More informationResidential Garage Door WARNING
Residential Garage Door INFORMATION EZ-SET TORSION S TORSION S EXTENSION S Improper Installation or Door Position Can Result in Serious Injury or Death. Read and understand all instructions before you
More informationHydraulic systems 2 Dimensioning
595-177-E 2015-12-07 Hydraulic systems 2 Dimensioning Hydraulic systems 2... 1 Dimensioning... 1 Introduction... 3 1 HOSE LENGTH CALCULATION... 4 1.1 Definition of hydraulic hose length... 4 1.2 Hose length
More informationMaking Spars for the Schooner Jeanette
Making Spars for the Schooner Jeanette..... by Byron Rosenbaum Figure 1. Byron Rosenbaum s 1:16-scale radio-controlled model of the schooner Jeanette. All photographs by the builder. The spars required
More information2. Note that the ropes from the rigging board are secured in the cam cleats of the jib fairleads.
VII 1. Place the hull, bow into wind, on its trailer, a soft surface, or a rigging board. We strongly recommend making a rigging board; it is simple and inexpensive and greatly simplifies rigging and working
More informationOperating instruction for the quick-change tap holders type:
type: HF 20 HF 30 Date of edition: 15.07.2008 Stage of alteration: 4 Please keep this for future use! Contents: 1 Application range, safety instructions and technical data... 3 1.1 Application range,
More informationMasthead Sensor Installation Guide
2315 1/2 Artesia Blvd. Redondo Beach, CA 90278 (310) 320-4349 (310) 320-5026 Fax www.signetmarine.com service@signetmarine.com Masthead Sensor Installation Guide 2.3 Masthead Sensor Installation Continued
More informationInstallation Guide, MPower Echelon Console
Installation Guide, MPower Echelon Console AC Performance, AC Sport and AC Performance Plus Schwinn Echelon Console (External Routing) 1. Install batteries to console. Mount the console to the bike. 2.
More informationL.Ph. Bolander & Sons 1355 Evans Ave. 800/
L.Ph. Bolander & Sons 1355 Evans Ave. 800/434-5611 San Francisco, Ca. 94124 Fax 415/648-0402 GOUNDSET ALUMINUM FLAGPOLE INSTALLATION INSTRUCTIONS STEP 1: DIG THE HOLE TO THE DIMENSIONS LISTED BELOW STEP
More informationSchaefer s New Mainsail Furler Answers All Your Questions
Boom Furler FAQ s Schaefer s New Mainsail Furler Answers All Your Questions Q: Why put a mainsail furler on your boat? A: Contemporary mainsail furlers allow you to: Shorten sail without leaving the safety
More informationChesapeake Tartan 30 Association
Chesapeake Tartan 30 Association MAST PUMPING & TARTAN 30 BABY STAY* John D. Connor, T-30 #142, writes: When the boat is tied up at the dock, and the wind is abeam, the mast starts vibrating ( pumping
More informationSailTrack Installation Instructions. CMPE Track
SailTrack Installation Instructions CMPE Track SH-500 SS SH-401 SS SH-200B SS SH-600 SS SH-200A SS www.tidesmarine.com This Tides Marine Sail Track System is used to attach a Tides Track to a bare carbon
More informationSGY-PM910H2/HL/LR ChainRing Adapter Installation Manual
SGY-PM910H2/HL/LR ChainRing Adapter Installation Manual 1 Table of Contents Table of Contents... 2 1 Assembling the Chainring and Installing the Right Transmitter... 3 2 Installation procedure of the adapter
More informationINSTALLING YOUR CLC RUDDER
INSTALLING YOUR CLC RUDDER These instructions are written to help you install the CLC rudder kit on your wooden kayak. The rudder can be fitted to your boat during construction or after completion. Please
More informationReefing systems. S-Hooks for slab reef or Cunningham
Reefing systems Traditional slab reef This is a simple and efficient reefing system. The reef cringle on the luff is hooked on to fixed hooks at the inboard end. The leech is reefed down with a line running
More informationTuning Guide January 2012
Tuning Guide January 2012 www.skud.org This tuning guide has been prepared by the IACA SKUD 18 Committee to assist new sailors in the SKUD 18 class to prepare their MkI or MkII boat to a competitive level
More informationSeldén offer a full range of spinnaker equipment for keelboats. It consists of five aluminium pole sections, three carbon fibre sections, low weight
56 Seldén offer a full range of spinnaker equipment for keelboats. It consists of five aluminium pole sections, three carbon fibre sections, low weight composite end fittings, telescopic whisker poles,
More informationCIRRUS AIRPLANE MAINTENANCE MANUAL MODELS SR22 AND SR22T CHAPTER 55-40: RUDDER GENERAL. Rudder 55-40: RUDDER. 1. General
CIRRUS AIRPLANE MAINTENANCE MANUAL Rudder CHAPTER 55-40: RUDDER GENERAL 55-40: RUDDER 1. General The rudder provides airplane directional (yaw) control and includes a rudder trim tab used for yaw trim
More informationaero naut Order No. 3009/00
aero naut Order No. 3009/00 Introduction: The model should be assembled following the sequence of the stages of construction described in these instructions. The laser-cut components are individually numbered.
More informationCHAPTER 5 REWIND STARTERS
GENERAL INFORMATION CHAPTER 5 REWIND S Rewind starters used on vertical shaft Tecumseh engines are top mount horizontal pull style or side mount vertical pull style. Horizontal shaft engines use side mounted
More informationMODEL CHEST PULLEY SYSTEM
MODEL 9180 CHEST PULLEY SYSTEM 1 PARTS LIST FOR CHEST PULLEY Note: Check with your architect or a professional contractor for hardware required to attach the unit to the wall and floor in your facility.
More informationSymptom: The basic symptom is your sail will not roll in or out without force. The drum unit is hard to turn. Your sail will not roll out on its own.
Schaefer 2100 roller furler drum replacement on Catalina 320 Danny Jensen, A BOA VIDA hull #972, Thanks to contributions Chris Burti, Jeff Hare and C320 group for comments Photos were taken and edited
More informationQuikVang. The Original High-Performance Vang INSTALLATION AND OPERATING INSTRUCTIONS MODEL A-8 MODEL A-12
QuikVang The Original High-Performance Vang INSTALLATION AND OPERATING INSTRUCTIONS MODEL A-8 MODEL A-12 33 Broadcommon Road, Bristol, RI 02809 USA T: 401.253.4858 F: 401.253.2552 www.hallspars.com 1 INTRODUCTION
More informationCIRRUS AIRPLANE MAINTENANCE MANUAL
RUDDER 1. GENERAL The rudder provides airplane directional (yaw) control and includes a rudder trim tab used for yaw trim adjustment. The rudder is of conventional design with skin, spar and ribs manufactured
More informationChapter Twelve. Starting the rigging process
Chapter Twelve Starting the rigging process Before I begin describing the rigging process, I must remind folks that it would be a great time to slip that traveler ring onto the bowsprit. I forgot to mention
More informationSEADUCER BOATS GAS SPORT HYDRO
SEADUCER BOATS GAS SPORT HYDRO COME VISIT US ON THE WEB AT WWW.SEADUCERBOATS.COM 2 - Pkg. Of 440 push rod ends 2 - Pkg. of solder-on rod ends 2 -water outlet fitting 1-1/4" prop nut 1 -.250" x 30" flex
More informationA. TO PREPARE THE MACHINE FOR USE.
INSTRUCTION MANUAL FOR THE ML120 STRINGING MACHINE. CONTENTS: A. TO PREPARE THE MACHINE FOR USE. 1. The assembly of frame with console and tooltray. 2. Fixing the lever of the tension unit. 3. Putting
More informationAccess Dinghy. Electrics. Installation. Manual
Access Dinghy Electrics Installation Manual SA1.e May, 00 ELECTRICS INSTALLATION MANUAL 1. Mark (using old cutout) and drill a pilot hole as the centre for inspection port in the starboard or right side
More informationSafety Afloat. Before you go sailing:
RIGGING MANUAL Safety Afloat This instruction manual is not a guide to sailing your craft and it should not be considered suitable for the task of learning to sail a boat. Please read the manual before
More informationBladerider X8 Assembly Help Notes
2.1 Remove All Parts & Have Some Tools Handy Remove all items from the box and identify each part as per the packing sheet and check that nothing is missing. If there is something missing, please email
More informationPanoptix PS51-TH FrontVü/LiveVü Thruhull
Panoptix PS51-TH FrontVü/LiveVü Thruhull Transducer Installation Instructions Important Safety Information WARNING See the Important Safety and Product Information guide in the chartplotter or fishfinder
More informationSchaefer recognized this issue and they offer to replace the drum bearing assembly for $
Schaefer 2100 roller furler drum replacement on Catalina 320 Danny Jensen, A BOA VIDA hull #972, Thanks to contributions Chris Burti, Jeff Hare and C320 group for comments Photos were taken and edited
More informationOver Deck Control Lines V1
Over Deck Control Lines V1 1 - Pack Contents Downhaul control line Outhaul control line Downhaul takeup elastic 3 x 30mm block Traveller line (with pre-spliced loop) 2 x Side deck strops 2 x Ronstan Shocks
More informationMonsoon repair/service helper. To high: Shoot a couple of shots until you get under 210bar, if it is higher than 210bar it will
Monsoon repair/service helper 1. Pressure: Min 180bar Max 210bar To low: Charge with air To high: Shoot a couple of shots until you get under 210bar, if it is higher than 210bar it will Not be able to
More information(PLEASE CONTACT YOUR LOCAL DEALER or CUSTOMER SERVICE FOR WARRANTY INFORMATION)
RUDDER KIT SOLO AND TANDEM KAYAKS IMPORTANT: For Tandem kayaks, the Supplemental Kit will be needed in addition to this kit and can be purchased through a registered dealer. The addition of a rudder to
More informationPico rigging manual 2007.doc Page 1 of 28
Pico rigging manual 2007.doc Page 1 of 28 Pico Rigging Instructions The Pico rigging instructions are a guide to rigging your boat. Due to production supplies certain parts may be slightly modified from
More informationInstallation of 2 Tier In Line Greeting Card Rack
Installation of 2 Tier In Line Greeting Card Rack Material Sent to Store: Greeting Card Fixtures: 4ft Inline Tier Kit (1 per every 4ft based on planogram) 3ft endcap Tier Kit (will not receive if planogram
More informationDIRECT DRIVE DIXIE DOUBLE SEAMER Model 25D
OPERATOR'S MANUAL DIRECT DRIVE DIXIE DOUBLE SEAMER Model 25D LUBRICATE DAILY: A. Gears inside gear housing at chuck shaft (1) Oil B. Seam rolls and cam rolls (4) - Oil C. Seam roll levers through gear
More informationHobie Island Spinnaker Instructions
Hobie Island Spinnaker Instructions Please read through the instruction manual before using this product. 2 Installation Components 1. 2. 1. Swivel Cam Cleat 2. Mount for Cleat w/ Hardware 3. Padeye w/
More informationCOMMON MEASUREMENT PROBLEMS & SOLUTIONS JUNE 2011
COMMON MEASUREMENT PROBLEMS & SOLUTIONS JUNE 2011 The main measurement problems still found in the 470 Class are the incorrect positioning of the mainsail on the mast and boom with the associated stopper
More informationSERIES 2 RAMP OWNER S MANUAL TOOLS REQUIRED: BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup.
SERIES 2 RAMP OWNER S MANUAL BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup. Use caution and care for your back when lifting, pushing, pulling, folding or unfolding
More informationE S JIB FURLING & REEFING SYSTEM. Manual Furlex 100 S
595-102-E 1999-12-13 100 S JIB FURLING & REEFING SYSTEM Manual Furlex 100 S 2 1 Introduction 1.1 The manual To derive the maximum benefit and enjoyment from your Furlex system, we recommend that you study
More informationNew Product Update - September 2017
New Product Update September 2017 Series 1 Ball Bearing Utility Blocks Available Now With a sheave diameter of 1mm these are the smallest and lightest ball bearing blocks available! The single block delivers
More informationIndex 1. Trampoline 2. Main Foils 3. Spinnaker Pole 4. Mast Setup 5. Mast Rigging 6. Rig Tension 7. Trapeze Lines 8. Rudders 9. Boom 10. Main Sheet an
By User Manual Index 1. Trampoline 2. Main Foils 3. Spinnaker Pole 4. Mast Setup 5. Mast Rigging 6. Rig Tension 7. Trapeze Lines 8. Rudders 9. Boom 10. Main Sheet and Traveler 11. Main Sail 12. Downhaul
More information44 CE RANGE WATERTIGHT SURFACE-MOUNTING JUNCTION BOXES
WALL BOXES IN GWPLAST 75 - GWT 650 C GWT 650 C TP 85 C WALLS WITH CABLE GLAND - IP44 AND IP55 GW44001 JUNCTION BOXES WITH PLAIN PRESS-ON LID - IP44 - GREY RAL 7035 LxHxD (mm) No. holes / Ø GW 44 001 Ø
More informationMODEL / SINGLE and DUPLEX PULLEY SYSTEMS
MODEL 922181/922182 SINGLE and DUPLEX PULLEY SYSTEMS MODEL 922181 SINGLE PULLEY SYSTEM MODEL 922182 DUPLEX PULLEY SYSTEM 1 PARTS LIST FOR SINGLE/DUPLEX COLUMN PULLEYS Note: Check with your architect or
More informationIn each step, the needed parts are shown the number right below. Locate all parts for the step.
Tools Required for Assembly Phillips Screwdriver, Med Needle Nose Pliers Sandpaper (#400 grit) Hobby Knife Scissors CA Instant Glue Rubbing Alcohol Drill Bit 1/16", 1.6mm 5/64, 2mm 1/8, 3mm 5/32, 4mm Before
More informationRIGGING INSTRUCTIONS Let's assume that you have your boat on a trailer when you take delivery from your dealer.
This is the original owner's manual, written about 1972, and applicable for boats manufactured through 1978. Starting in 1979 a few changes were made in the roller furling jib and forestay arrangement.
More informationWysiwig - Wayfarer Rigging Guide
Wysiwig - Wayfarer 8767 - Rigging Guide GENERAL NOTES Before you go afloat, make sure that the self-bailer is closed. It is operated through the cut-out in the starboard floorboard. If you do not close
More informationHOBIE TEDDY ASSEMBLY MANUAL
ASSEMBLY MANUAL HOBIE TEDDY HOBIE CAT EUROPE ZI Toulon Est, BP 50 83078 Toulon cedex 9, France Tel : +33 (0)494 08 78 78 - Fax : +33 (0)494 08 3 99 Email : info@hobie-cat.net - http://www.hobie-cat.net
More informationJ/70 Building Specification
DECK, HARDWARE AND FITTINGS 1 FRP Composite deck 2 Indeck furler unit 3 Bow "U" bolt mooring eye (stainless) Option for one 6" (152mm) mooring cleat in lieu of eye. 4 Shroud chainplates (stainless) (BSI
More informationINSTALLING THE PROWLER 13 RUDDER
INSTALLING THE PROWLER 13 RUDDER Parts Included: Steering Parts: Foot Rail Parts: Rudder Parts: Retraction Parts: 4 Rubber 2 Rail Assemblies Rudder Body 1 Rudder Retraction Grommets (includes steering
More information1 Tuning Platform Reseating Beam Pads Rudder alignment Noisy Foils Rig Tension...
Contents 1 Tuning... 2 1.1 Platform... 2 1.2 Reseating Beam Pads... 2 1.3 Rudder alignment... 3 1.4 Noisy Foils... 3 1.5 Rig Tension... 4 1.6 Mast rake... 4 1.7 Spreader rake... 5 1.8 Diamond tension...
More informationInternal Sealing of Masts
595-814-E 2007-02-15 Internal Sealing of Masts (Replaces the sealing instructions 595-551-SE) Vertical high line Kicker bracket Sec. sealing hole Drain hole Conventional masts This instruction is enclosed
More informationMODEL TRIPEX PULLEY SYSTEM
MODEL 922184 TRIPEX PULLEY SYSTEM 1 PARTS LIST FOR TRIPEX PULLEY SYSTEM Note: Check with your architect or a professional contractor for hardware required to attach the unit to the wall and floor in your
More informationSailTrack Installation Instructions. External Track
SailTrack Installation Instructions External Track SH-500 SS SH-401 SS SH-600 SS SH-200B SS SH-200A SS www.tidesmarine.com Before You Begin Your installation will be easier if you move the boom well off
More informationE Sailmaker s guide. Everything a sailmaker needs to know about Seldén masts, booms and furling systems.
595-542-E 2018-04-04 Sailmaker s guide Everything a sailmaker needs to know about Seldén masts, booms and furling systems. S 1) K D H ~ 100 2 1 Introduction This guide is intended to provide sailmakers
More informationSerial Number: Lot Number: Purchase Date: General Factors Accepted / Rejected Supportive Details or Comments. Accepted Rejected.
Full Body Harness Harness Model: General Factors / Supportive Details or Comments 1.) Hardware: (includes D-rings, buckles, keepers, and back pads) Inspect for damage, distortion, sharp edges, burrs, cracks
More informationSealing kit manual. For sealing of conventional mast sections C156-C304 and furling mast sections F176-F305. Comes with sealing kit
597-182-E 2015-01-16 Sealing kit manual For sealing of conventional mast sections C156-C304 and furling mast sections F176-F305. Comes with sealing kit 312-322-10 2 1. General information This sealing
More information12.9 Gennaker. February Setting up and sailing with the 12.9 Gennaker
12.9 Gennaker Setting up and sailing with the 12.9 Gennaker February 2013 The 12.9 Gennaker is a new bigger gennaker for the Weta. The standard gennaker is 8 sqm and the 12.9 gennaker is 12.9 sqm. The
More informationVanguard Sailboats 300 Highpoint Avenue Portsmouth, RI For the dealer nearest you call SAIL
Vanguard Sailboats 300 Highpoint Avenue Portsmouth, RI 02871 For the dealer nearest you call 800. 966.SAIL Unpack the major parts listed below and lay them out on a soft piece of ground free of sharp objects.
More informationQUALITY ALUMINUM BOAT LIFTS, INC. INSTRUCTIONS. Dominator Lake Lift
INSTRUCTIONS Dominator Lake Lift PHONE:251-986-3882 * FAX:251-986-3136 QABLDOMINATORINST.2014 P a g e 1 Quality Aluminum Boat Lifts, INC. Installation Instructions: Dominator Lake Lift Thank you for your
More informationOMS P/N: Rev.: B. Description OMS: ASSY BACKUP POD 6.0. DCR# 3137 Date: Operation: Special Instructions: TQC. Torque.
DCR# Date: -0- ASSY BACKUP POD.0 BPEVE OMS P/N: 00-09 Rev.: B Page: of NA P-Touch Labels Apply Label & Serial Number/Part Number Label onto the front of the chassis as shown. OMS Template: 00-00 Rev. A
More informationPT 11 trouble-shooting and maintenance.
PT 11 trouble-shooting and maintenance. Does your rudder not stay down?...your back seat slip off?...your knobs tight and your leather pads loose? Maybe we can help. We have used our PT 11 s hard enough
More information