TRIMARAN HULL DESIGN FOR FAST FERRY APPLICATIONS
|
|
- Job May
- 6 years ago
- Views:
Transcription
1 TRIMARAN HULL DESIGN FOR FAST FERRY APPLICATIONS Stefano Brizzolara, Marco Capasso, Marco Ferrando, Carlo Podenzana Bonvino Dept. of Naval Architecture and Marine Technologies, Univ. of Genova, Italy; Antonio Cardo, Alberto Francescutto Dept. of Naval Architecture, Ocean and Environmental Engineering, Univ. of Trieste. ABSTRACT: Research studies about hydrodynamic performance of trimaran hull configurations and their application to real ship design, are relatively recent, having generally appeared in the last two decades of the last century, without relevant follow up in the shipbuilding world. The proposed paper aims to describe the main features of the hydrodynamic design of a trimaran ship as an alternative solution to contemporary mono hull or catamaran fast ferries (36-40 knots of service speed). This work has been developed in the frame of a three year joint research project of the Departments of Naval Architecture of the Universities of Genova, Trieste and Napoli and the University of Ancona. Comparison of the main resistance and seakeeping properties of two different trimaran design (having different hull forms but equivalent in terms of main geometric parameters and total displacement), tested in model scale with different side hulls positions will be addressed in the paper. The design exercise presented in the paper has comprehended also other aspects such as the implications that different hull typologies can have on the general layout of the vessel, problems related to the intact and damaged stability, internal spaces and propulsion arrangements.
2 INTRODUCTION After Triton (the trimaran demonstrator built by DERA in 2000 [1] the shipbuilding world became conscious that modern and efficient ships could also be built having a trimaran hull configuration. Nevertheless, the advantages and implication of trimarans in terms of the general ship design have been rarely published [2]. Aiming to fill this gap this paper proposes a comparison between the main characteristics of two different hull geometries for a fast ferry trimaran for commercial applications. The design of both trimaran hulls has been based on an initial market survey which brought to the definition of the basic reference design conditions, such as the merchant ship type, mission profile and payload. As a result of this study [3], the Mediterranean sea scenario and a medium size fast ferry able to carry passengers and cars having the following design characteristics were selected: - Main hull L/B>10 - Displacement of each side hull: about 5% of total - Maximum total breadth: approx. 28 m - Service speed: up to 40 knots - Payload: 800 passengers and 240 cars The value of L/B ratio of the main hull (taking into account that a total breadth around 28 m allows the vessel to use standard harbor facilities for monohull vessels), relatively lower with respect to other trimaran designs, was chosen in order to obtain a reasonable breadth of the lower car decks of the main hull, while preserving reasonably low wave resistance at high speed, and good seakeeping. Having a maximum speed exceeding (by more than 50%) the value of computed at the design displacement volume, the trimaran is to be considered a high-speed craft and falls under the regulations of IMO HSC Code. The amount of buoyancy reserved to the side hulls was selected as a compromise to obtain additional reserve of buoyancy for stability and to limit as much as possible the increase in total resistance. The first trimaran design was prepared as a consequence of the first design spiral performed for the feasibility project. Subsequently, an alternative hull design for the same targets has been prepared [4] allowing an interesting comparison between the two different hull geometries, equivalent from the main design specifications, i.e. payload, speed, range and main geometric parameters relevant to the resistance and seakeeping performance of the vessel. Both hull geometries are described in detail in the next sections. The two main and side hulls have been designed in such a way to be fully interchangeable, to permit a direct comparison of the effect of the hull typology on the hydrodynamic performance of the trimaran, without any other side effects due to the variation of main geometric parameters such as length and displacement or initial attitude, for instance.
3 HULL FORM GEOMETRIES Different design of both central and side hulls has been done from the first to the second model. Main geometrical characteristics of the two alternative main hulls and corresponding side hulls are given in Table 1. The first trimaran features a main typical fast round bilge hull (Figure 1) having V-type bow sections with low flair and stern U-type sections closed towards the transom in both vertical and transversal directions. The deadrise angle of the main section is around 15 deg.. The longitudinal prismatic coefficient was kept rather low (0.645) to limit wave resistance together with the high slenderness ratio L/B and L/ 1/3. Side hulls were designed like with hard chines forms (Figure 1) with simple slightly convex bow sections, high deadrise angle of the Tab. 1: Main geom. characteristics of both design main section (abt. 29 deg.) and slightly warped aft straight sections. The main hull of the second model was chosen of Deep-V type (Figure 2). In the case of high speed monohull ships, in fact, it was shown that Deep-V hull forms have considerable advantages over conventional round bilge hulls, in terms of resistance and seakeeping ([5] and [6]) at high speed. The idea, then, was that of check these advantages also in the case of a trimaran ship. The main Deep-V hull features simple transverse section made of straight line having high deadrise angle at the main section (abt. 34 deg.), same length and displacement of the previous hull as well as same C P and LCB for a fairer comparison of the residual resistance of the two alternative main hulls. The fullness of the main section results lower than that of the first round bilge hull so a higher breadth and draft were necessary to obtain an equal displacement. Stern bottom lines, still straight, are highly warped toward the transom where the bottom becomes almost horizontal and the sections close gradually in transversal direction. The same transom area was maintained for both main hulls, in order to permit the same waterjet arrangement and roughly the same contribution of the transom wave formation to the wave resistance. The side hulls of the second model (Figure 2) were re-designed as well, assuming simple symmetric U-type section with a very small transom. The models of the two trimarans were built to a scale of 1:60 and tested in the towing tank of the University of Genova for still water resistance tests and in the towing tank of the University of Trieste for seakeeping. The trimaran models were built in ABS material by means of a modern technique used in mechanical engineering for rapid prototyping (Fused
4 Figure 1: Body plan of the main round bilge hull and of the asymmetric side hulls (half side of the body plan) of the first trimaran deposition Modeling), with an overall accuracy of about +/- 0.15%. Having defined Clearance and Stagger as follows, it was decided to test the model with a systematic variation of stagger and clearance of the side hulls side hulls according to the test matrix presented in Table 2. Stagger (%) = Long. distance between the side hulls transom and the main hull transom, in percent of a reference main hull length equal to 120m. Clearance (%) = Lateral distance between the external side (in case of first model) or symmetry Table 2: Clearance and Stagger test values Figure 3: Variation of the absolute clearance (CL) and the absolute stagger (ST) for symmetric and asymmetric side hulls Figure 2: Body plan of the main Deep-V hull and of the symmetric side hulls of the second trimaran plane (in case of second model) of the side hulls and the main hull symmetry plane, in percent of a reference main hull length equal to 120m. A sketch illustrating the relative hulls positions for different values of Clearance and Stagger is provided in Figure 3.
5 Figure 4: General plan of the first trimaran fast ferry design Figure 5: Embarking car deck and engine room views of the second trimaran GENERAL ARRANGEMENTS Two possible solutions regarding the general arrangements of the trimarans are shown in Figure 4 and 5 at a Stagger and Clearance values close to the optimal solutions from the resistance point of view (PL1-PT1 for both trimarans as explained in resistance paragraph).
6 As reported in the following the comparison between the trimarans will start from the just mentioned figures as explanatory enough. The main car deck, in fact, although strongly conditioned by the configuration chosen, is not influenced by the effect of the side hulls shape, extremely narrow for both trimarans. Focusing the analysis on the consequences that a choice of the main hull geometry has on the payload, it is possible to note that the embarking car deck, thanks to an highest local hull breadth, allows an increase of about 10% for the loaded cars (from 65 to 72). Since also the hoistable car deck and the lower car deck behave in the same way, the main hull shape of the second trimaran is more effective in terms of load capacity of the ship. As visible from the engine room views of Figure 4 and 5, the distribution of the hull volume at the stern (especially with regards to 2 ½ and 3 water line) allow to maintain the same engine arrangement for both trimarans and hence the theoretical validity of the present comparison. STILL WATER RESISTANCE Both models of trimarans have been tested at DINAV Towing Tank at Froude numbers in the range to (full scale speed range knots). For some of the hull configurations of the first trimaran, the tests at the highest speeds were not performed due to an unfavorable interference between the wave formation of the central and the side hulls, so bad to produce a very Figure 6: Full scale effective power (PL1 configurations) Figure 7: Full scale effective power (PL2 configurations)
7 Figure 8: Full scale effective power (PL3 configurations) Position L1 L2 L3 T0 x x x T1 x T2 x T3 x high internal wave crest, ultimately causing danger of model flooding. In this paper the comparison of performance between the two hulls is discussed in terms of effective power at full scale, the resistance being predicted with ITTC-57 procedure. For the first model, as presented in [7] and [8], the towing tank tests indicated that the minimum value of P ES in the intermediate speed range (25-30 knots) is occurring at high clearance and low stagger values (PL1-PT3) or for low stagger and intermediate clearance values (PL1-PT2). On the contrary, the trends at higher speeds show that the minimum P ES is obtained for low stagger and clearance values (PL1-PT0 and PL1-PT1, transom in line and side hulls closer to the main hull), taking into account that also the configuration PL3- PT3 provides comparable results, against a less realistic solution as regards internal arrangements. This finding is in quite good agreement with results from Ackers et al. [9] which were used in the preliminary power estimation of the research project. This agreement is obviously qualitative, since Ackers results are given in terms of percent interference while our results are total resistance at full scale. In Figures 6, 7, and 8 trimaran full scale effective power curves P ES are given for the different clearances at constant stagger values for both trimarans (first number indicating the trimaran design version, so 1PT0 is the first trimaran with clearance PT0). Tests results, in fact, were performed fisrt for six configurations of the second model, which have been tested first since they resulted to provide the lowest values of resistance for the first model (see table 3). In all the configuration tested, the second hull design showed a better resistance than the first. This difference can be ascribed essentially at the difference Table 3: Second model configurations between hull form typologies, having the main parameters affecting the residual resistance almost the same value among the two models (L WL, C P,B/T,). Moreover being the wetted surface of the second model notably higher than the first one, the relative advantage on the residual resistance in even more pronounced than what appears from the total resistance. More details about the tests results and analysis can be found in [7,10]. In any case already in previous studies in the case of monohulls, deep-v hull forms showed advantages over conventional round bilge hulls especially at highest speeds. In this case, at V S =42 knots the 2PT1-PL1 solution (P ES = 26MW) is in absolute the best denoting an advantage of about 10% over the first trimaran (1 PL1-PT1; P ES = 29MW).
8 SEAKEEPING Besides the still water resistance tests, a campaign of tests in head regular waves to check seakeeping qualities of the two hulls was planned on the basis of the best configurations identified as regards performance in calm water. The results, in this paper reported in terms of added resistance and heave transfer functions compared with a same length monohull (frigate) optimised for seakeeping, are reported in Figure 9 and in Figure 10. More detailed results concerning seakeeping are going to be presented in [11]. To avoid excessive flooding of the models due to green water in head waves, a maximum ship speed of 30 knots and a small wave amplitude (at fixed steepness equal to 1/100 for both trimarans) was adopted. Due to the difference in longitudinal position of the centre of gravity of the different trimaran configurations, heave was reported in all cases to the middle perpendicular. The lower vertical motions of the second design shown by the heave transfer function in Figure 9 can be correlated with the deep-v shape of the central hull, usually having more vertical motion damping than equivalent round bilge monohull [6] at higher speeds (Fn= ). Present study was more oriented to the analysis of the effect of position of outriggers. Tests are actually under schedule with different combinations of side-main hulls (such as all deep-v hulls). The cross analysis of these tests will allow the assessment of the influence of the side hull geometry and form on the global behaviour of the trimaran ship. For sake of comparison between the two trimarans, the case of added resistance corresponding to wavelength equal to ship length (which is close to the maximum), is reported in Fig. 10. Taking into account that the same values of displacement and L WL of both trimarans allow a direct comparison between the two Figure 9: Heave transfer function of first trimaran design at Vs=30 kn (Frigate: without marks ) models, both diagrams show a certain improvement in performance of the second design,
9 Figure 10: Added Resistance comparison of both trimaran design at different speeds especially in the PT3-PL3 configuration at high speed. The configuration PT0-PL1, identified as the best for to side resistance, does not result to be the best for the added resistance, where the case PL3-PT3 results in advantage. In these terms a compromise in the design solution is in general necessary, depending on the priority scale of the performance assumed (comfort and operability against fuel consumption and speed). STABILITY As regards stability, both trimaran designs have been checked with respect to present criteria of the IMO/HSC rules. A trimaran ship, as expected, has in general an intermediate static stability between those of monohulls and catamarans. Despite a very high intact stability, the conditions become critical when an asymmetric flooding is considered, as arguable from figure 12. Figure 12, in fact, synthesises the verification of the most stringent stability requirements in the intact condition (a) and for two damaged condition corresponding to the side (b) and bottom(c) damage cases foreseen by actual IMO-HSC rules, i.e. the sided + gusting + heeling due to passenger crowding or high speed turning. Especially in the asymmetric damaged condition the righting arm curve of the trimaran has an evident slope discontinuity around Figure 11: Initial and modified watertight volumes of the second trimaran design (in the static equilibrium angle for the asymmetric damaged condition c) degree (depending on the analysed case and trimaran design) caused by the emergence of the intact side hull opposite to the heeled side. The subsequent drastic loss of righting moment (that would be dramatic in the case of a catamaran) is mitigated by the contribution to stability of the trimaran main hull and by the above water volumes of the damaged side. Monohull fast ships, on
10 Figure 12: Verification of worst dynamic criteria of intact (wind + gusting + high speed turning) and damage stability (crowding +wind) for multihull ships. First trimaran design (left) and second trimaran design (right).
11 the other hand, do not suffer at all by this problem, having in general symmetric flooding which can bring, instead, to freeboard problems with respect to the lower car deck. To better appreciate the effect of buoyancy reserve of the side hulls during dynamic heeling moment, first the second trimaran has been intentionally verified with slender side hulls also in the above water portion (see figure 11). And in fact this extreme layout (unrealistic also for structural reasons) cannot satisfy the dynamic criteria in the case of worst asymmetric damaged condition (i.e. side damage of case c) of figure 12), while intact and bottom damaged criteria (case a and b) are satisfied. In summary, the trimaran designer as in the case of catamarans has to be very well aware of the risks of asymmetric flooding and in particular he is required to provide a convenient shape to the above water side hull to cope with the dynamic stability requirements of the IMO-HSC code, once having fixed the lateral position of side hulls from resistance or seakeeping considerations. CONCLUSIONS Two different designs for the same target ship, a trimaran fast ferry operating in the Mediterranean sea, differing mainly in the hull form typologies, have been described and analyzed in the paper with regards to basic design characteristics (general arrangement, propulsion, stability, etc.) and hydrodynamic performance as regards resistance and seakeeping. The second hull form is based on a deep-v main hull, similar to those used in modern monohull fast ferries, in alternative to the more conventional round bilge first main hull. The design exercise confirmed in both cases a appreciable freedom in the plan of internal arrangement and a great margin on intact and damaged stability if proper volumes in the above water portion of the side hull are reserved. As regards damaged stability the trimaran, in fact, behaves in a intermediate way respect to a monohull and a catamaran, mitigating the negative effects of an a- symmetric flooding (of side hull), that can result to be dramatic for a catamaran. Predicted still water resistance at full scale of both designs, based on model tests with different relative position of side hulls, show a general marked advantage of the second design against the first one, in the medium-high speed range for all the best positions of lateral hulls found for the first design, the best overall position of side hulls, at high speed, being the less advanced and relatively closest one. Seakeeping performance of the second model results also advantageous, especially at high speed for heave motions and added resistance. The configurations featuring the best resistance and seakeeping performance are not the same in both designs, so the designer needs to do, in general, a compromise taking into account damage stability and general layout at the same time. Further activities will comprise the completion of systematic tests for all all the other possible configuration (obtained by interchanging main and side hulls). A deeper analysis will be devoted to assess the relative
12 performance of designed trimarans against actual monohull fast ferries, since from preliminary consideration they do not show marked advantages. NOMENCLATURE SYMBOL S.I. UNIT DESCRIPTION A TR [m 2 ] transom area A X [m 2 ] main section area B WL [m] max beam on WL C B = /(B WL L WL T) block coefficient C P =/(A T L WL ) prismatic coefficient C WL waterplane area coefficient C X main section area coefficient D [m] depth of ship on MP Fn= V / (g L WL ) 1/2 Froude number g [m/s 2 ] gravity acceleration h trans [m] transom draft L OA [m] over all length LCB longitudinal centre of buoyancy L or L PP [m] length between perpendiculars L WL [m] length of waterline P ES [kw] full scale effective power S [m 2 ] wetted surface T [m] draft V S [m/s,knots] ship speed V m [m/s,] model speed [m 3 ] volume w [m] wave length h w [m] wave height HTF [m] heave transfer function e [rad/s] encounter frequency REFERENCES 1. Various, R.V. TRITON: Trimaran Demonstrator Project (2000) Proceeding RINA Conference, Southampton (U.K.), April Pattison D. R., Zhang J.W., (1994), Trimaran Ships, Transactions of Royal Institution of Naval Architects, Vol. pp Benvenuto, G., Brizzolara, S., Figari, M., Podenzana Bonvino, C., (2001a) Fast Trimaran Ships: Some Examples for Commercial Application, Proc. HIPER'01, 2nd Int. Euroconference on High Performance Marine Vehicles, Hamburg, July 2001, pp Brizzolara, S, (2002) Design of New Trimaran Hull Forms with Deep-V Main Hull and Round Bilge Side Hulls, in Alternative to the First DINAV Trimaran Design: Body Plan, Hydrostatics and Stability, DINAV Internal Report SB (in Italian). 5. Brizzolara, S., Grossi, L., (1997) Design Aspects and Applications of Deep- V Hull Forms to High Speed Crafts, Proc. of IMDEX 97 International
13 Maritime Defence Exhibition & Conference, Greenwich-London, October Grossi, S. Brizzolara, L. Sebastiani, G. Caprino (1998), Seakeeping Design of Fast Monohull Ferries, Proc. of PRADS 98 International Symposium on Practical Design of Ships and Mobile Units, Den Hag, Sept Capasso, M., Ferrando, M., Podenzana Bonvino, C., Cardo, A., Francescutto, A., (2001) Study of the Hydrodynamic Performances of a Trimaran Ship for Fast Transportation, Proceedings 1st Int. Congress on Maritime Transport, Barcelona, November 2001, Olivella Puig et al. Eds, pp Cardo, A., Francescutto, A., Capasso, M., Ferrando, M., Podenzana Bonvino, C., "Hydrodynamic Performance in Waves of a Trimaran Ship", CD Proceedings of 10th International Congress of IMAM, Rethimnon, May Ackers B., Michael T.J., Tredennik O.W., Landen H.C., et al., (1997), An investigation of the Resistance Characteristics of Powered Trimaran side- Hull Configurations, SNAME Transactions, Vol. 105, pp Cardo, A., Ferrando, M., Podenzana Bonvino C., (2003) Influence of hull shape on the resistance of a fast trimaran vessel, to appear on Proceedings of FAST 2003 Conference, Sorrento (Italy). 11. Brizzolara, S., Capasso, M., Francescutto, A., (2003) Effect of hulls form variations on the hydrodynamic performances in waves of a trimaran ship, to appear on Proceedings of FAST 2003 Conference, Sorrento (Italy).
MEDIUM SPEED CATAMARAN WITH LARGE CENTRAL BULBS: EXPERIMENTAL INVESTIGATION ON RESISTANCE AND VERTICAL MOTIONS
MEDIUM SPEED CATAMARAN WITH LARGE CENTRAL BULBS: EXPERIMENTAL INVESTIGATION ON RESISTANCE AND VERTICAL MOTIONS Igor Zotti, University of Trieste, Department D.I.N.M.A., Italy SUMMARY: It has been noticed
More informationITTC - Recommended Procedures and Guidelines
7.5 Page 1 of 5 Table of Contents 1. PURPOSE OF PROCEDURE... 2 2. DESCRIPTION OF PROCEDURE... 2 4. DOCUMENTATION... 4 5. REFERENCES... 4 3. PARAMETERS... 4 Updated by Approved Manoeuvring Committee of
More informationCRITERIA OF BOW-DIVING PHENOMENA FOR PLANING CRAFT
531 CRITERIA OF BOW-DIVING PHENOMENA FOR PLANING CRAFT Toru KATAYAMA, Graduate School of Engineering, Osaka Prefecture University (Japan) Kentarou TAMURA, Universal Shipbuilding Corporation (Japan) Yoshiho
More informationRESOLUTION MSC.141(76) (adopted on 5 December 2002) REVISED MODEL TEST METHOD UNDER RESOLUTION 14 OF THE 1995 SOLAS CONFERENCE
MSC 76/23/Add.1 RESOLUTION MSC.141(76) THE MARITIME SAFETY COMMITTEE, RECALLING Article 38(c) of the Convention on the International Maritime Organization concerning the functions of the Committee, RECALLING
More informationfor Naval Aircraft Operations
Seakeeping Assessment of Large Seakeeping Assessment of Large Trimaran Trimaran for Naval Aircraft Operations for Naval Aircraft Operations Presented by Mr. Boyden Williams, Mr. Lars Henriksen (Viking
More informationEXPERIMENTAL MEASUREMENT OF THE WASH CHARACTERISTICS OF A FAST DISPLACEMENT CATAMARAN IN DEEP WATER
EXPERIMENTAL MEASUREMENT OF THE WASH CHARACTERISTICS OF A FAST DISPLACEMENT CATAMARAN IN DEEP WATER A.F. Molland, P.A. Wilson and D.J. Taunton Ship Science Report No. 124 University of Southampton December
More informationShip Stability. Ch. 8 Curves of Stability and Stability Criteria. Spring Myung-Il Roh
Lecture Note of Naval Architectural Calculation Ship Stability Ch. 8 Curves of Stability and Stability Criteria Spring 2016 Myung-Il Roh Department of Naval Architecture and Ocean Engineering Seoul National
More informationSTABILITY OF MULTIHULLS Author: Jean Sans
STABILITY OF MULTIHULLS Author: Jean Sans (Translation of a paper dated 10/05/2006 by Simon Forbes) Introduction: The capsize of Multihulls requires a more exhaustive analysis than monohulls, even those
More informationComparative Stability Analysis of a Frigate According to the Different Navy Rules in Waves
Comparative Stability Analysis of a Frigate According to the Different Navy Rules in Waves ABSTRACT Emre Kahramano lu, Technical University, emrek@yildiz.edu.tr Hüseyin Y lmaz,, hyilmaz@yildiz.edu.tr Burak
More informationThree New Concepts of Multi-Hulls
Three New Concepts of Multi-Hulls Victor A. Dubrovsky Independent designer, Russian Federation 114-71 Budapeshtskaja Str, St.Petersburg, 192283, Russian Federation Multi-hulls@yandex.ru Abstract Many multi-hull
More informationDAMAGE STABILITY TESTS OF MODELS REPRESENTING RO-RC) FERRIES PERFORMED AT DMI
TECHNISCHE UNIVERSITET laboratoriurn vow Scheepshydromechareba slechlef Meketweg 2, 2628 CD. Delft Tel.: 015-788873 - Fax 015-781838 DAMAGE STABILITY TESTS OF MODELS REPRESENTING RO-RC) FERRIES PERFORMED
More informationITTC Recommended Procedures Testing and Extrapolation Methods Loads and Responses, Seakeeping Experiments on Rarely Occurring Events
Loads and Responses, Seakeeping Page 1 of 5 CONTENTS 1. PURPOSE OF PROCEDURE 2. STANDARDS FOR EXPERIMENTS ON RARELY OCCURRING EVENTS 2.1 Previous Recommendations of ITTC 2.2 Model Design and Construction
More informationIMO REVISION OF THE INTACT STABILITY CODE. Proposal of methodology of direct assessment for stability under dead ship condition. Submitted by Japan
INTERNATIONAL MARITIME ORGANIZATION E IMO SUB-COMMITTEE ON STABILITY AND LOAD LINES AND ON FISHING VESSELS SAFETY 49th session Agenda item 5 SLF 49/5/5 19 May 2006 Original: ENGLISH REVISION OF THE INTACT
More informationExperimental Study on the Large Roll Motion of a ROPAX Ship in the Following and Quartering Waves
Experimental Study on the Large Roll Motion of a ROPAX Ship in the Following and Quartering Waves Sun Young Kim, Nam Sun Son, Hyeon Kyu Yoon Maritime & Ocean Engineering Research Institute, KORDI ABSTRACT
More informationNumerical and Experimental Investigation of the Possibility of Forming the Wake Flow of Large Ships by Using the Vortex Generators
Second International Symposium on Marine Propulsors smp 11, Hamburg, Germany, June 2011 Numerical and Experimental Investigation of the Possibility of Forming the Wake Flow of Large Ships by Using the
More informationMinimising The Effects of Transom Geometry on Waterjet Propelled Craft Operating In The Displacement and Pre-Planing Regime
Minimising The Effects of Transom Geometry on Waterjet Propelled Craft Operating In The Displacement and Pre-Planing Regime SUMMARY James Roy, Nigel Gee and Associates Ltd, UK John Bonafoux, Nigel Gee
More informationThe salient features of the 27m Ocean Shuttle Catamaran Hull Designs
The salient features of the 27m Ocean Shuttle Catamaran Hull Designs The hull form is a semi-planing type catamaran. It employs a combination of symmetrical and asymmetrical sponson shapes, thereby combining
More informationSECOND ENGINEER REG III/2 NAVAL ARCHITECTURE
SECOND ENGINEER REG III/2 NAVAL ARCHITECTURE LIST OF TOPICS A B C D E F G H I J Hydrostatics Simpson's Rule Ship Stability Ship Resistance Admiralty Coefficients Fuel Consumption Ship Terminology Ship
More informationINCLINOMETER DEVICE FOR SHIP STABILITY EVALUATION
Proceedings of COBEM 2009 Copyright 2009 by ABCM 20th International Congress of Mechanical Engineering November 15-20, 2009, Gramado, RS, Brazil INCLINOMETER DEVICE FOR SHIP STABILITY EVALUATION Helena
More informationPerformance of SSTH-70 after Delivery and Future of SSTH Masahiro Itabashi, Ryoji Michida Ishikawajima-Harima Heavy Industries Co.,Ltd.
Performance of SSTH-70 after Delivery and Future of SSTH Masahiro Itabashi, Ryoji Michida Ishikawajima-Harima Heavy Industries Co.,Ltd. ABSTRUCT The SSTH-70 Ocean Arrow designed under the concept of the
More informationLong and flat or beamy and deep V-bottom An effective alternative to deep V-bottom
Boat dual chines and a narrow planing bottom with low deadrise Long and flat or beamy and deep V-bottom An effective alternative to deep V-bottom Here is a ground-breaking powerboat concept with high efficiency
More informationA HYDRODYNAMIC METHODOLOGY AND CFD ANALYSIS FOR PERFORMANCE PREDICTION OF STEPPED PLANING HULLS
POLISH MARITIME RESEARCH 2(86) 2015 Vol. 22; pp. 23-31 10.1515/pomr-2015-0014 A HYDRODYNAMIC METHODOLOGY AND CFD ANALYSIS FOR PERFORMANCE PREDICTION OF STEPPED PLANING HULLS Hassan Ghassemi, Assoc. Prof.
More informationA Study on Roll Damping of Bilge Keels for New Non-Ballast Ship with Rounder Cross Section
International Ship Stability Workshop 2013 1 A Study on Roll Damping of Bilge Keels for New Non-Ballast Ship with Rounder Cross Section Tatsuya Miyake and Yoshiho Ikeda Department of Marine System Engineering,
More informationStudy of Passing Ship Effects along a Bank by Delft3D-FLOW and XBeach1
Study of Passing Ship Effects along a Bank by Delft3D-FLOW and XBeach1 Minggui Zhou 1, Dano Roelvink 2,4, Henk Verheij 3,4 and Han Ligteringen 2,3 1 School of Naval Architecture, Ocean and Civil Engineering,
More informationShallow-Draft Ro-Pax Ships for Various Cargos and Short Lines
Journal of Water Resources and Ocean Science 2017; 6(5): 65-70 http://www.sciencepublishinggroup.com/j/wros doi: 10.11648/j.wros.20170605.12 ISSN: 2328-7969 (Print); ISSN: 2328-7993 (Online) Shallow-Draft
More informationEXPERIMENTAL WIND TUNNEL TESTS ON LARGE PASSENGER SHIPS
EXPERIMENTAL WIND TUNNEL TESTS ON LARGE PASSENGER SHIPS Andrea Serra, Fincantieri SpA, Cruise Ship Business Unit, Trieste, Italy, e-mail: andrea.serra@fincantieri.it SUMMARY The papers was developed as
More informationStudy on Resistance of Stepped Hull Fitted With Interceptor Plate
39 Study on Resistance of Stepped Hull Fitted With Interceptor Plate Muhamad Asyraf bin Abdul Malek, a, and J.Koto, a,b,* a) Department of Aeronautic, Automotive and Ocean Engineering, Faculty of Mechanical
More informationTHE PERFORMANCE OF PLANING HULLS IN TRANSITION SPEEDS
THE PERFORMANCE OF PLANING HULLS IN TRANSITION SPEEDS BY DOYOON KIM UNIVERSITY OF SOUTHAMPTON LIST OF CONTENTS AIM & OBJECTIVE HYDRODYNAMIC PHENOMENA OF PLANING HULLS TOWING TANK TEST RESULTS COMPUTATIONAL
More informationStability Analysis of a Tricore
Stability Analysis of a Tricore C. M. De Marco Muscat-Fenech, A.M. Grech La Rosa AbstractThe application of stability theory has led to detailed studies of different types of vessels; however, the shortage
More informationISSN: ISO 9001:2008 Certified International Journal of Engineering Science and Innovative Technology (IJESIT) Volume 2, Issue 4, July 2013
A Comparison of Hull Resistances of a Mono-Hull and A SWATH Craft Josip Medaković, Ban Dario, Branko Blagojević University of Split, FESB, Department of Mechanical Engineering and Naval Architecture, 21000
More informationCERTIFICATES OF COMPETENCY IN THE MERCHANT NAVY MARINE ENGINEER OFFICER
CERTIFICATES OF COMPETENCY IN THE MERCHANT NAVY MARINE ENGINEER OFFICER EXAMINATIONS ADMINISTERED BY THE SCOTTISH QUALIFICATIONS AUTHORITY ON BEHALF OF THE MARITIME AND COASTGUARD AGENCY STCW 95 CHIEF
More informationSAMPLE MAT Proceedings of the 10th International Conference on Stability of Ships
and Ocean Vehicles 1 Application of Dynamic V-Lines to Naval Vessels Matthew Heywood, BMT Defence Services Ltd, mheywood@bm tdsl.co.uk David Smith, UK Ministry of Defence, DESSESea-ShipStab1@mod.uk ABSTRACT
More informationITTC Recommended Procedures and Guidelines
Page 1 of 6 Table of Contents 1. PURPOSE...2 2. PARAMETERS...2 2.1 General Considerations...2 3 DESCRIPTION OF PROCEDURE...2 3.1 Model Design and Construction...2 3.2 Measurements...3 3.5 Execution of
More informationA New Approach to the Derivation of V-Line Criteria for a Range of Naval Vessels
A New Approach to the Derivation of V-Line Criteria for a Range of Naval Vessels Andrew Peters 1, Rick Goddard 2 and Nick Dawson 1 1. QinetiQ, Haslar Marine Technology Park (UK) 2. Steller Systems Ltd.,
More informationA STUDY OF THE LOSSES AND INTERACTIONS BETWEEN ONE OR MORE BOW THRUSTERS AND A CATAMARAN HULL
A STUDY OF THE LOSSES AND INTERACTIONS BETWEEN ONE OR MORE BOW THRUSTERS AND A CATAMARAN HULL L Boddy and T Clarke, Austal Ships, Australia SUMMARY CFD analysis has been conducted on a 100m catamaran hull
More informationCFD PREDICTION OF THE WAVE RESISTANCE OF A CATAMARAN WITH STAGGERED DEMIHULLS
MAHY 2006: International Conference on Marine Hydrodynamics 5-7January 2006, Visakhapatnam, India CFD PREDICTION OF THE WAVE RESISTANCE OF A CATAMARAN WITH STAGGERED DEMIHULLS Prasanta K. Sahoo Senior
More informationApplication and Development of Multi-Hulls
April 20, 204 Application and Development of Multi-Hulls a) Balt Techno Prom, St.Petersburg, Russia Victor A. Dubrovsky, a,* *Corresponding author: multi-hulls@yandex.ru Paper History Received: 8-January-204
More informationFigure 1: The squat effect. (Top) Ship at rest. (Bottom) Ship under way.
Under-Keel Clearance of Frigates and Destroyers in Shallow Water Tim Gourlay, Centre for Marine Science and Technology, Curtin University CMST Research Report 013-53 Abstract For RAN ships operating in
More informationDynamic Stability of Ships in Waves
Gourlay, T.P. & Lilienthal, T. 2002 Dynamic stability of ships in waves. Proc. Pacific 2002 International Maritime Conference, Sydney, Jan 2002. ABSTRACT Dynamic Stability of Ships in Waves Tim Gourlay
More informationITTC Recommended Procedures and Guidelines
Page 1 of 7 Table of Contents 2 1. PURPOSE... 2 2. PARAMETERS... 2 2.2. General Considerations... 2 2.3. Special Requirements for Ro-Ro Ferries... 3 3.3. Instrumentation... 4 3.4. Preparation... 5 3.5.
More informationSelecting Monohull, Catamaran and Trimaran as Suitable Passenger Vessels Based on Stability and Seakeeping Criteria
Selecting Monohull, Catamaran and Trimaran as Suitable Passenger Vessels Based on Stability and Seakeeping Criteria Richard B Luhulima 1, D Setyawan 2, and I K A P Utama 3 1. PhD Student Dept. of Naval
More informationPERFORMANCE PREDICTION OF THE PLANING YACHT HULL
PERFORMANCE PREDICTION OF THE PLANING YACHT HULL L A le Clercq and D A Hudson, University of Southampton, UK SUMMARY The performance of racing yachts has increased significantly over the past 10-15 years
More informationAbstract. 1 Introduction
A computational method for calculatingthe instantaneous restoring coefficients for a ship moving in waves N. El-Simillawy College of Engineering and Technology, Arab Academyfor Science and Technology,
More informationDesign of high-speed planing hulls for the improvement of resistance and seakeeping performance
csnak, 2013 Int. J. Naval Archit. Ocean Eng. (2013) 5:161~177 http://dx.doi.org/10.2478/ijnaoe-2013-0124 Design of high-speed planing hulls for the improvement of resistance and seakeeping performance
More informationInternational Journal of Maritime Engineering
International Journal of Maritime Engineering THE BORE PRODUCED BETWEEN THE HULLS OF A HIGH-SPEED CATAMARAN IN SHALLOW WATER T Gourlay, Curtin University, J Duffy, Australian Maritime College and A Forbes,
More informationSample Application of Second Generation IMO Intact Stability Vulnerability Criteria as Updated during SLF 55
1 Sample Application of Second Generation IMO Intact Stability Vulnerability Criteria as Updated during SLF 55 Clève Wandji, Bureau Veritas Philippe Corrignan, Bureau Veritas ABSTRACT A second generation
More informationEffect of Hull Form and its Associated Parameters on the Resistance of a Catamaran
Effect of Hull Form and its Associated Parameters on the Resistance of a Catamaran Zulkarnain Bin Ramsani *1, Ivan CK Tam *2, and Arun Dev *3 *School of Marine Science and Technology, Newcastle University
More informationInternational Journal of Marine Engineering Innovation and Research, Vol. 2(2), Mar (pissn: , eissn:
(pissn: 2541-5972, eissn: 2548-1479 176 Analysis of Lift and Drag of Mono-foil Hysucat due to Longitudinal Foil-placement Variation Ketut Suastika 1, Regi Y. Dikantoro 1, Dedi B. Purwanto 1, Dony Setyawan
More informationTHE PREDICTION OF WAKE WASH IN THE TOWING TANK
Jurnal Mekanikal December 2008, No. 26, 129-140 THE PREDICTION OF WAKE WASH IN THE TOWING TANK Mohamad Pauzi Abdul Ghani 1*, M.N. Abdul Rahim 2 1 Faculty of Mechanical Engineering, Universiti Teknologi
More informationPREDICTING THE ABILITY OF SURVIVAL AFTER DAMAGE IN TANKERS. José Poblet Martínez - SENER, (Spain) José Javier Díaz Yraola - SENER, (Spain)
8 th International Conference on 477 PREDICTING THE ABILITY OF SURVIVAL AFTER DAMAGE IN TANKERS Abstract José Poblet Martínez - SENER, (Spain) José Javier Díaz Yraola - SENER, (Spain) To meet the demand
More informationA Feasibility Study on a New Trimaran PCC in Medium Speed
The 6 th International Workshop on Ship ydrodynamics, IWS 010 January 9-1, 010, arbin, China Feasibility Study on a ew Trimaran PCC in Medium Speed Tatsuhiro Mizobe 1*, Yasunori ihei 1 and Yoshiho Ikeda
More informationThe influence of the high-speed Trimaran to Flow Field. Yi-fan Wang 1, Teng Zhao 2
5th International Conference on Advanced Design and Manufacturing Engineering (ICADME 2015) The influence of the high-speed Trimaran to Flow Field Yi-fan Wang 1, Teng Zhao 2 1 Chongqing jiaotong university,400074,chongqing
More informationUnderstanding How Excessive Loading Lead to a Capsize with Loss of Life Can Help Avoid Future Tragedies
Understanding How Excessive Loading Lead to a Capsize with Loss of Life Can Help Avoid Future Tragedies By Dave Gerr, CEng FRINA 2012 Dave Gerr fter sailing out to watch the fireworks on July 4th, 2012,
More informationCOMPARATIVE ANALYSIS OF CONVENTIONAL AND SWATH PASSENGER CATAMARAN
COMPARATIVE ANALYSIS OF CONVENTIONAL AND SWATH PASSENGER CATAMARAN Serđo Kos, Ph. D. David Brčić, B. Sc. Vlado Frančić, M. Sc. University of Rijeka Faculty of Maritime Studies Studentska 2, HR 51000 Rijeka,
More informationIMO BULK CARRIER SAFETY. Bulk Carrier Model Test Progress Report. Submitted by the United Kingdom
INERNAIONA MARIIME ORGANIZAION E IMO MARIIME SAFEY COMMIEE 75th session Agenda item 5 MSC 75/5/3 12 March 22 Original: ENGISH BUK CARRIER SAFEY Bulk Carrier Model est Progress Report Submitted by the United
More informationMarine Kit 4 Marine Kit 4 Sail Smooth, Sail Safe
Marine Kit 4 Marine Kit 4 Sail Smooth, Sail Safe Includes Basic ship Terminologies and Investigation Check list Index 1. Ship Terminology 03 2. Motions of a Floating Body...09 3. Ship Stability.10 4. Free
More informationInvestigation of the Intact Stability Accident of the Multipurpose Vessel MS ROSEBURG
Proceedings of the 12th International Conference on the Stability of Investigation of the Intact Stability Accident of the Multipurpose Vessel MS ROSEBURG Adele Lübcke, Institute of Ship Design and Ship
More informationS0300-A6-MAN-010 CHAPTER 2 STABILITY
CHAPTER 2 STABILITY 2-1 INTRODUCTION This chapter discusses the stability of intact ships and how basic stability calculations are made. Definitions of the state of equilibrium and the quality of stability
More informationEXPERIMENTAL STUDY ON HEAVE AND PITCH MOTION CHARACTERISTICS OF A WAVE-PIERCING TRIMARAN
Karim Akbari Vakilabadi Mohammad Reza Khedmati Mohammad Saeed Seif ISSN 1333-1124 eissn 1849-1391 EXPERIMENTAL STUDY ON HEAVE AND PITCH MOTION CHARACTERISTICS OF A WAVE-PIERCING TRIMARAN Summary UDC 629.5.022.3:629.5.018.71
More informationA BARE HULL RESISTANCE PREDICTION METHOD DERIVED FROM THE RESULTS OF THE DELFT SYSTEMATIC YACHT HULL SERIES EXTENDED TO HIGHER SPEEDS
A BARE HULL RESISTANCE PREDICTION METHOD DERIVED FROM THE RESULTS OF THE DELFT SYSTEMATIC YACHT HULL SERIES EXTENDED TO HIGHER SPEEDS J A Keuning and M Katgert, Delft University of Technology, Netherands
More informationReliable Speed Prediction: Propulsion Analysis and a Calculation Example
Reliable Speed Prediction: Propulsion Analysis and a Calculation Example Donald M. MacPherson VP Technical Director HydroComp, Inc. ABSTRACT Speed prediction is more than just bare-hull resistance. Speed
More informationResistance and Stability Analysis for Catamaran Fishing Vessel with Solar Cell in Calm Water
Resistance and Stability Analysis for Catamaran Fishing Vessel with Solar Cell in Calm Water Teguh Putranto 1,*, Wasis Dwi Aryawan 1, Hesty Anita Kurniawati 1, Dony Setyawan 1, and Sri Rejeki Wahyu Pribadi
More information3D CDF MODELING OF SHIP S HEELING MOMENT DUE TO LIQUID SLOSHING IN TANKS A CASE STUDY
Journal of KONES Powertrain and Transport, Vol. 17, No. 4 21 3D CDF ODELING OF SHIP S HEELING OENT DUE TO LIQUID SLOSHING IN TANKS A CASE STUDY Przemysaw Krata, Jacek Jachowski Gdynia aritime University,
More informationShip Resistance and Propulsion Prof. Dr. P. Krishnankutty Ocean Department Indian Institute of Technology, Madras
Ship Resistance and Propulsion Prof. Dr. P. Krishnankutty Ocean Department Indian Institute of Technology, Madras Lecture - 17 Resistance of Advanced Marine vehicles - III (Refer Slide Time: 00:10) Now,
More informationNUMERICAL AND EXPERIMENTAL STUDY OF WAVE RESISTANCE FOR TRIMARAN HULL FORMS
NUMERICAL AND EXPERIMENTAL STUDY OF WAVE RESISTANCE FOR TRIMARAN HULL FORMS Thomas Mynard, Research student at Australian Maritime College, PO Box 986, Launceston, TAS 750, Australia Prasanta K Sahoo,
More informationWind Turbine Shuttle. Ferdinand van Heerd
Wind Turbine Shuttle Ferdinand van Heerd Contents Introduction Concept Resistance Seakeeping Vessel motion compensation system Hoisting motion compensation system Landing the wind turbine Workability Efficiency
More informationMOTION CONTROL IN WAVES OF A 140M SES
OS5-2 Proceedings of the 7th JFPS International Symposium on Fluid Power, TOYAMA 2008 September 15-18, 2008 MOTION CONTROL IN WAVES OF A 140M SES Naoki OHBA*, Taketsune MATSUMURA*, Akihiko IMAKITA* * Basic
More informationZIPWAKE DYNAMIC TRIM CONTROL SYSTEM OUTLINE OF OPERATING PRINCIPLES BEHIND THE AUTOMATIC MOTION CONTROL FEATURES
ZIPWAKE DYNAMIC TRIM CONTROL SYSTEM OUTLINE OF OPERATING PRINCIPLES BEHIND THE AUTOMATIC MOTION CONTROL FEATURES TABLE OF CONTENTS 1 INTRODUCTION 3 2 SYSTEM COMPONENTS 3 3 PITCH AND ROLL ANGLES 4 4 AUTOMATIC
More informationVessel Modification and Hull Maintenance Considerations Options & Pay Back Period or Return On Investments
Vessel Modification and Hull Maintenance Considerations Options & Pay Back Period or Return On Investments By Dag Friis Christian Knapp Bob McGrath Ocean Engineering Research Centre MUN Engineering 1 Overview:
More informationHydrostatics and Stability Dr. Hari V Warrior Department of Ocean Engineering and Naval Architecture Indian Institute of Technology, Kharagpur
Hydrostatics and Stability Dr. Hari V Warrior Department of Ocean Engineering and Naval Architecture Indian Institute of Technology, Kharagpur Module No.# 01 Lecture No. # 01 Introduction Hello everybody.
More informationThe Usage of Propeller Tunnels For Higher Efficiency and Lower Vibration. M. Burak Şamşul
The Usage of Propeller Tunnels For Higher Efficiency and Lower Vibration M. Burak Şamşul ITU AYOC 2014 - Milper Pervane Teknolojileri Company Profile MILPER is established in 2011 as a Research and Development
More informationThe Windward Performance of Yachts in Rough Water
14th Chesapeake Sailing Yacht Symposium January 3, 1999 The Windward Performance of Yachts in Rough Water Jonathan R. Binns, Australian Maritime Engineering Cooperative Research Centre Ltd. (AME CRC) Bruce
More informationFinding the hull form for given seakeeping characteristics
Finding the hull form for given seakeeping characteristics G.K. Kapsenberg MARIN, Wageningen, the Netherlands ABSTRACT: This paper presents a method to find a hull form that satisfies as good as possible
More informationMODEL TESTS TO STUDY CAPSIZE AND STABILITY OF SAILING MULTIHULLS
MODEL TESTS TO STUDY CAPSIZE AND STABILITY OF SAILING MULTIHULLS Barry Deakin Wolfson Unit MTIA, University of Southampton, UK ABSTRACT Sailing multihull cruising yachts cannot be righted from a capsize
More informationITTC Recommended Procedures and Guidelines
Page 1 of 10 Table of Contents 1. PURPOSE... 2 2. NUMERICAL METHODS... 2 3. PREPARATION, SIMULATIONS AND ANALYSIS... 4 3.1 Geometry... 4 3.2 Preparations... 5 3.3 Wave conditions... 6 3.4 Wind conditions...
More informationThe Effect of Mast Height and Centre of Gravity on the Re-righting of Sailing Yachts
THE 17 th CHESAPEAKE SAILING YACHT SYMPOSIUM ANNAPOLIS, MARYLAND, MARCH 25 The Effect of Mast Height and Centre of Gravity on the Re-righting of Sailing Yachts Jonathan R. Binns, Researcher, Australian
More informationThis lesson will be confined to the special case of ships at rest in still water. Questions of motions resulting from waves are not considered at
STATIC STABILITY When we say a boat is stable we mean it will (a) float upright when at rest in still water and (b) return to its initial upright position if given a slight, temporary deflection to either
More informationTHE EFFECTS OF THE HULL VANE ON SHIP MOTIONS OF FERRIES AND ROPAX VESSELS
THE EFFECTS OF THE HULL VANE ON SHIP MOTIONS OF FERRIES AND ROPAX VESSELS K Uithof, B Bouckaert, P G van Oossanen, and N Moerke, Hull Vane B.V., van Oossanen Naval Architecture, and van Oossanen Fluid
More informationRULES FOR THE CONSTRUCTION AND CLASSIFICATION OF SHIPS IDENTIFIED BY THEIR MISSIONS CHAPTERS SCOPE
PART II RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF SHIPS IDENTIFIED BY THEIR MISSIONS TITLE 12 CONTAINER SHIPS SECTION 1 NAVAL ARCHITECTURE CHAPTERS A SCOPE B DOCUMENTS, REGULATIONS AND STANDARDS
More informationOPTIMISATION OF HYDROFOIL-SUPPORTED-PLANING CATAMARANS
Presentation delivered to the Third International Conference on Fast Sea Transportation (FAST 95) in Lubeck-Travemunde, Germany, 25-27 September 1995, by Prof.Dr- Ing..K.G.Hoppe, Mechanical Engineering
More informationSubj: Explanation of Upper Level Capacity and Stability Characteristics for Rolling Boat, Inc. Vessels.
23 Apr, 2009 From: Tullio Celano III P.E. To: Underwriters of Rolling Boat, Inc. Via: Phil Kazmierowicz, President, Rolling Boat, Inc. Subj: Explanation of Upper Level Capacity and Stability Characteristics
More informationThe Inefficiencies of modern Trawler propulsion as a consequence of trends in hull form and length restrictions
The Inefficiencies of modern Trawler propulsion as a consequence of trends in hull form and length restrictions 3 Castlecourt St Josephs Rd Mallow, Co.Cork Ireland. Tel +353 87 3435666 Fax +353 22 22467
More informationShip Stability September 2013 Myung-Il Roh Department of Naval Architecture and Ocean Engineering Seoul National University
Planning Procedure of Naval Architecture and Ocean Engineering Ship Stability September 2013 Myung-Il Roh Department of Naval Architecture and Ocean Engineering Seoul National University 1 Ship Stability
More informationFAST SUPPLY INTERVENTION and CREW TRANSFER VESSEL M P 6 2 5
FAST SUPPLY INTERVENTION and CREW TRANSFER VESSEL M P 6 2 5 MAIN PARTICULARS LENGTH OVER ALL 60.68 m LENGTH WATER LINE 59.35 m BREADTH MAX 20.80 m DRAUGHT MAX 3.10 m DEPTH 6.70 m MAX SPEED 37.0 knots @
More informationAbstract. 1 Introduction
Parametric analysis of hull structure of mono- and catamaran-type inland vessels T. Jastrzebski & Z. Sekulski Faculty ofmaritime Technology, Technical University of Szczecin, AL Piastow 41, 71-065 Szczecin,
More informationResistance Analysis for a Trimaran Claire M. De Marco Muscat-Fenech, Andrea M. Grech La Rosa
Resistance Analysis for a Trimaran Claire M. De Marco Muscat-Fenech, Andrea M. Grech La Rosa Abstract Importance has been given to resistance analysis for various types of vessels; however, explicit guidelines
More informationInterceptors in theory and practice
Interceptors in theory and practice An interceptor is a small vertical plate, usually located at the trailing edge on the pressure side of a foil. The effect is a completely different pressure distribution
More informationSHIP FORM DEFINITION The Shape of a Ship
SHIP FORM DEFINITION The Shape of a Ship The Traditional Way to Represent the Hull Form A ship's hull is a very complicated three dimensional shape. With few exceptions an equation cannot be written that
More informationIMO REVISION OF THE INTACT STABILITY CODE. Evaluation of the roll prediction method in the weather criterion. Submitted by the United Kingdom
INTERNATIONAL MARITIME ORGANIZATION E IMO SUB-COMMITTEE ON STABILITY AND LOAD LINES AND ON FISHING VESSELS SAFETY 51st session Agenda item 4 SLF 51/INF.2 April 28 ENGLISH ONLY REVISION OF THE INTACT STABILITY
More informationDESIGN & TECHNOLOGY Design & Technology
Page 1 of 5 Leading the World in the Design and Construction of Customised Aluminium Commercial and Defence Vessels Home About Austal Product Information Careers at Austal De DESIGN & TECHNOLOGY Design
More informationSOFTWARE. Sesam user course. 12 May 2016 HydroD Hydrostatics & Stability. Ungraded SAFER, SMARTER, GREENER DNV GL 2016
SOFTWARE Sesam user course DNV GL 1 SAFER, SMARTER, GREENER Scope of presentation Describe features & commands for performing a hydrostatic analysis, and their concepts Analysis setup Code-checking Reporting
More informationShip Resistance and Propulsion Prof. Dr. P. Krishnankutty Ocean Department Indian Institute of Technology, Madras
Ship Resistance and Propulsion Prof. Dr. P. Krishnankutty Ocean Department Indian Institute of Technology, Madras Lecture - 7 Air and Wind Resistance Dimensional Analysis I Coming back to the class, we
More informationModel Tests to Study Capsize and Stability of Sailing Multihulls
Model Tests to Study Capsize and Stability of Sailing Multihulls Barry Deakin, Wolfson Unit MTIA, University of Southampton, UK ABSTRACT Sailing multihull cruising yachts cannot be righted from a capsize
More informationSafety practices related to small fishing vessel stability
18 The vessel s centre of gravity (G) has a distinct effect on the righting lever (GZ) and consequently the ability of a vessel to return to the upright position. The lower the centre of gravity (G), the
More informationAN UPDATE ON THE DEVELOPMENT OF THE HULL VANE
AN UPDATE ON THE DEVELOPMENT OF THE HULL VANE K. Uithof 1, P. van Oossanen 1,2, N. Moerke 1,2, P.G. van Oossanen 1,2, and K.S. Zaaijer 2 1 Hull Vane B.V., Costerweg 1b, 6702 AA, Wageningen, Netherlands
More informationMultihull Preliminary Stability Estimates are Fairly Accurate
Multihull Design (Rev. A) 45 APPENDIX A ADDITIONAL NOTES ON MULTIHULL DESIGN MULTIHULL STABILITY NOTES Multihull stability is calculated using exactly the same method as described in Westlawn book 106,
More informationConventional Ship Testing
Conventional Ship Testing Experimental Methods in Marine Hydrodynamics Lecture in week 34 Chapter 6 in the lecture notes 1 Conventional Ship Testing - Topics: Resistance tests Propeller open water tests
More informationAn Investigation into the Effect of Water Depth on the Resistance Components of Trimaran Configuration
An Investigation into the Effect of Water Depth on the Resistance Components of Trimaran Configuration Muhammad,IQBAL 1 and I Ketut Aria Pria, UTAMA 2 1 Department of Naval Architecture Diponegoro University,
More informationHull Separation Optimization of Catamaran Unmanned Surface Vehicle Powered with Hydrogen Fuel Cell
Hull Separation Optimization of Catamaran Unmanned Surface Vehicle Powered with Hydrogen Fuel Cell Seok-In Sohn, Dae-Hwan Park, Yeon-Seung Lee, Il-Kwon Oh International Science Index, Physical and Mathematical
More informationA Note on the Capsizing of Vessels in Following and Quartering Seas
Oceanic Engineenng International, Vol. 1, No. 1, 1997, pp. 25-32 A Note on the Capsizing of Vessels in Following and Quartering Seas MARTIN RENILSON' * 'Australian Maritime Engineering CRC Ltd, c/o Australian
More information