Design of submarine pressure hulls to withstand buckling under external hydrostatic pressure
|
|
- Rafe Curtis
- 6 years ago
- Views:
Transcription
1 icccbe 2010 Nottingham University Press Proceedings of the International Conference on Computing in Civil and Building Engineering W Tizani (Editor) Design of submarine pressure hulls to withstand buckling under external hydrostatic pressure Carl T.F. Ross, Terry Whittaker & Andrew P.F. Little University of Portsmouth, UK Abstract The paper presents an investigation into various methods of calculating the theoretical collapse loads for a pressure vessel, under uniform external hydrostatic pressure; based on different design codes. The design codes used for the investigation were BS 5500, for vessels under external pressure and also, the design charts of Ross of the University of Portsmouth. It is the opinion of the present authors that the current design methodology, namely BS 5500 was difficult to use and gave inaccurate collapse pressures for some large-scale pressure vessels. Moreover, BS 5500 appeared to be too pessimistic for one mode of failure and too optimistic for another mode of failure. For the present study, a full-scale theoretical pressure vessel was used and the fore mentioned methodologies applied in its design to see if there were any similarities that each method may have had. From the results obtained, it became apparent that some methodologies were more accurate than others, depending on the mode of collapse. Moreover, it also became apparent that some of the methods themselves were outdated, user-unfriendly and in some cases, may have even been dangerous. Keywords: submarines, pressure hulls, hydrostatic pressure, structural design 1 Introduction Under uniform external hydrostatic pressure, a submarine pressure hull can buckle through shell instability or lobar buckling at a pressure (Ross, 1965; Ross, 2001), which may be a fraction of the same vessel to explode under uniform internal pressure, as shown in Figure 1.
2 Figure 1, Shell instability of a circular cylinder This mode of failure is undesirable, as it is structurally inefficient and one way of improving its structural inefficiency, is to ring-stiffen it with suitable sized ring stiffeners, spaced at suitable distances apart. If, however, the ring stiffeners are not strong enough, the entire ring-shell combination can buckle bodily in its flank, through a mode of failure called general instability, as shown in Figure 2. Figure 2, General instability If the ring stiffeners are very strong and the spacing between them is relatively small, then failure can take place through a mode of failure called axisymmetric deformation, where the circular cylinder keeps its circular form while imploding inwards, as shown in Figure 3. This mode of failure is more predictable and designers often prefer to design out the two instability modes of failure, so that if failure takes place, it fails through this more predictable mode of failure, called axisymmetric deformation. Figure 3, Axisymmetric collapse In this paper, we will design a full-scale model using BS 5500 and also, using Ross s (2001) codes.
3 2 The designs One full-scale structural design was considered, namely Submarine 1; details of which are given in Figure Submarine 1 Figure 4, Dimensions of the full-scale submarine The following parameters were used for Submarine 1: T = 2 = 50.8mm B = 1 = 25.4mm D = 8 = 203.2mm l = 27 = 685.8mm = 364 = mm R = 192 = mm Ε = Young s modulus = 3 e 07 Ksi = 2.07 e 05 GPa ν = Poisson s ratio = 0.3 σ = Yield stress = psi = 552 MPa Material of construction = HY80 Steel 2.2 Designing against shell instability In order to investigate shell instability, the section between adjacent frames was theoretically isolated and then the following two methods were employed to determine the collapse pressures due to shell instability: Design Chart of Ross et al (2009), which makes use of the Von Mises formula (1936), Design Chart of BS5500 (1980). The theoretical von Mises (1936) collapse pressure, for perfect circular cylinders was calculated using the computer program MISESNP.EXE (Ross, 2001). The computer program also calculates the Windenburg thinness Ratio (λ) (Windenburg & Trilling, 1934); this value will be used in conjunction with the design charts of Ross, to calculate the plastic knockdown factor, namely PKD and thus, the actual collapse pressure. The results from this program were as follows: λ= Thinness ratio = {(L/D) 2 /(T/D) 3 } 0.25 * (σ/e) 0.5 = Pcr = von Mises buckling pressure = 25 MPa with 14 lobes (n=14) Knowing λ, the required PKD has to be determined from the design chart of Ross et al (2009); see Figure 5.
4 Figure 5, Ross design chart for shell instability Now,. 1.4 Therefore, from Figure 5, PKD = 2.8 Now the von Mises theoretical buckling pressure for perfect vessels, namely Pcr, must be divided by PKD to give the actual predicted buckling pressure, namely Pcr (actual). P actual P = MP 8.9MPa 890m depth of water. PKD. From BS 5500 s design chart of Figure 6, the shell instability calculations were also carried out. Now K= P, P Where P m = the von Mises buckling pressure for perfect vessels & P y = 2σT/D = the pressure to cause axisymmetric yield. From Figure 6, P P = 0.56 Now P y = , therefore p 0.56 Py Converting to MPa MPa 10 Where p = actual buckling pressure, given by BS5500. From the above, it can be seen that a design depth of 472 m, by BS 5500 is too pessimistic, when dealing with shell instability, because Ross (2001) predicts a corresponding diving of 890m!
5 Figure 6, BS 5500 design chart 2.3 General instability To design against the general instability mode of failure, two methods below were used, namely Kendrick Part 1 (1953) 7 BS5500, as follows: Kendrick Part 1. BS 5500 which uses Bryant s formula (1954). The theoretical buckling pressure for Kendrick Part 1 was calculated by Ross computer program (2001). As the vessel that was analysed was of a ring stiffened nature, it was difficult to use Ross computer program, namely MISESNP (Ross, 2001), as MISESNP was intended for unstiffened circular cylinders. To overcome this problem, an equivalent shell thickness (T ), and equivalent vessel radius (Rf) were used to calculate the equivalent Windenburg s thinness ratio, namely λ (Windenburg and Trilling, 1934). From the design chart of Ross et al (2008); λ = 1.38, therefore: Hence, from Figure 7, PKD = 1.2. Figure 7, Ross design chart for general instability
6 From Ross computer program (2001), namely Kendrick Part1, Pcr (theoretical) = 6.2MPa (4 Lobes) Hence, the actual general instability buckling pressure, namely Pcr (actual) was calculated. Pcr Actual Pcr 6.2MPa 5.2MPa 520M PKD 1.2 From BS 5500, which was very difficult to use, we get, the lowest Pcr value to be: 6.46MPa, failing with 4 lobes; corresponding to a maximum diving depth of 646 m; which was positively dangerous, because Ross code gave a corresponding collapse diving depth of only 520m! 2.4 Axisymmetric deformation Using the Boiler Formula, Ross (1999), the collapse pressure= P = 5.7 MPa = 570m of water depth. We have no disagreement with using the Boiler Formula of BS5500! 3 Conclusions The findings from the results for Pressure Vessel 1 appear to show that BS 5500 is too pessimistic for shell instability, but worse still, too optimistic for general instability. The authors do not have any quarrel with BS 5500, as far as the axisymmetric mode of failure is concerned. Moreover, Ross design charts are much easier to use and in any case, their linear nature of Ross design charts make it easier for the designer to use. In contrast this; the design chart of BS 5500 is curved, making life difficult for the designer. Calculating the buckling pressures by BS 5500 is worsened because the calculations are very laborious, because they have to be done for every value of n, the number of circumferential waves that the vessel buckles into. This is necessary to obtain the minimum value of Pcr. References BRYANT, A.R., Hydrostatic pressure buckling of a ring-stiffened tube. NCRE Report No. R306, October. BSI, BS5500, British standards specification for unfired fusion welded pressure vessels. Issue 5. UK, British Standards Institution. ROSS, C.T.F., The collapse of ring-reinforced cylinders under uniform external pressure. Trans., RINA, 107, ROSS, C.T.F., The instability of ring-stiffened circular cylindrical shells under uniform external pressure. Trans., RINA, 107, ROSS, C.T.F., Mechanics of Solids, Chichester, UK, Horwood. ROSS, C,T.F., Pressure vessels: external pressure technology, Chichester, UK, Horwood. ROSS, C.T.F., OKOTO K.O. and LITTLE, A.P.F., Buckling by general instability of cylindrical components of deep sea submersibles. Paper 300 in Proceedings of the Ninth International Conference on Computational Structures Technology, B.H.V. Topping and M. Papadrakakis, (Editors), Civil-Comp Press, Stirlingshire, Scotland. ROSS, C.T.F., SPAHIU, A., BROWN, G.X. and LITTLE, A.F.P., Buckling of near-perfect thick-walled circular cylinders under external hydrostatic pressure. Journal of Ocean Technology, Vol.4., No. 2 pp VON MISES, R., USEMB Translation Report No. 366, Washington, DC, USA. WINDENBURG, D.F. and TRILLING, C., Collapse by instability of thin cylindrical shells under external pressure. Trans. ASME, 11,
Plastic non-symmetric bifurcation buckling of circular cylinders under uniform external hydrostatic pressure
icccbe 2010 Nottingham University Press Proceedings of the International Conference on Computing in Civil and Building Engineering W Tizani (Editor) Plastic non-symmetric bifurcation buckling of circular
More informationComposite tubing collapse under uniform external hydrostatic pressure
icccbe 2010 Nottingham University Press Proceedings of the International Conference on Computing in Civil and Building Engineering W Tizani (Editor) Composite tubing collapse under uniform external hydrostatic
More informationNon-linear general instability of ring-stiffened conical shells under external hydrostatic pressure
Journal of Physics: Conference Series Non-linear general instability of ring-stiffened conical shells under external hydrostatic pressure To cite this article: C T F Ross et al 2011 J. Phys.: Conf. Ser.
More informationNon-Linear Buckling of Conical Shells under External Hydrostatic Pressure
Paper 164 Non-Linear Buckling of Conical Shells under External Hydrostatic Pressure C.T.F. Ross, T. Eeeles, C. Fraser, J. Burt M. Fitzgerald, C. Knipe and A.P.F. Little School of Engineering University
More informationExtreme submarine NOT FOR REPRODUCTION
Extreme submarine Ross, Spahiu, Brown and Little present new charts for use in the design of small submarines to descend to the bottom of the deep ocean. Carl T.F. Ross Astrit Spahiu Graham X. Brown Who
More informationCollapse of composite tubes under uniform external hydrostatic pressure
Journal of Physics: Conference Series Collapse of composite tubes under uniform external hydrostatic pressure To cite this article: P T Smith et al 2009 J. Phys.: Conf. Ser. 181 012043 View the article
More informationAbstract. 1 Introduction
Buckling of circumferentially corrugated cylinders under uniform external pressure C.T.F. Ross," G. Apor,*) S.R Claridge* "Department ofmechanical and Manufacturing Engineering, University of Portsmouth,
More informationVessels subject to External Pressure
Basic principles of compressive force Vessels subject to External Pressure Before After The result of just air pressure! Presented by: Ray Delaforce Basic principles of compressive force Consider For a
More informationInvestigation of Stresses in Ring Stiffened Circular Cylinder
International Journal of Engineering and Technical Research (IJETR) ISSN: 2321-869, Volume-2, Issue-9, September 214 Investigation of Stresses in Ring Stiffened Circular Cylinder Neetesh N. Thakre, Dr.
More informationABSTRACT I. INTRODUCTION
2016 IJSRST Volume 2 Issue 4 Print ISSN: 2395-6011 Online ISSN: 2395-602X Themed Section: Science and Technology Modelling and Structural Analysis of a Pressure Hull under Dynamic Load P. Yamini Charishma
More informationNUMERICAL INVESTIGATION OF BUCKLING STRENGTH BEHAVIOR OF RING STIFFENED SUBMARINE PRESSUREE HULL
International Journal of Civil Engineering and Technology (IJCIET) Volume 8, Issue 8, August 2017, pp. 408 415, Article ID: IJCIET_08_08_041 Available online at http://http://ww www.iaeme.com/ijciet/issues.asp?jtype=ijciet&v
More informationTECHNICAL MEMORANDUM 3-81
WOODS HOLE OCEANOGRAPHIC INSTITUTION Woods Hole, Massachusetts 02543 TECHNICAL MEMORANDUM 3-81 DESIGN PRESS CURVES FOR OCEANOGRAPHIC URE-RESISTANT HOUSINGS Prepared by Arnold G. Sharp August 1981 Office
More informationBottom End-Closure Design Optimization of DOT-39 Non-Refillable Refrigerant Cylinders
Y. Kisioglu a) Department of Mechanical Education, Kocaeli University, Izmit, Kocaeli, 41100, Turkey J. R. Brevick Industrial and Systems Engineering, The Ohio State University, Columbus, Ohio G. L. Kinzel
More informationFatigue Life Evaluation of Cross Tubes of Helicopter Skid Landing Gear System
IJSRD - International Journal for Scientific Research & Development Vol. 3, Issue 04, 2015 ISSN (online): 2321-0613 Fatigue Life Evaluation of Cross Tubes of Helicopter Skid Landing Gear System Madhu S
More informationOTC Buckle Arrestors for Deepwater Pipelines Carl G. Langner / Langner & Associates
OTC 10711 Buckle Arrestors for Deepwater Pipelines Carl G. Langner / Langner & Associates Copyright 1999, Offshore Technology Conference This paper was prepared for presentation at the 1999 Offshore Technology
More informationFitness for Service Assessment of Ageing Pressure Vessel Experiencing External Corrosion: A Case Study
The International Journal Of Engineering And Science (IJES) Volume 6 Issue 2 Pages PP 12-16 2017 ISSN (e): 2319 1813 ISSN (p): 2319 1805 Fitness for Service Assessment of Ageing Pressure Vessel Experiencing
More informationDetermination of Burst Pressure of Spherical Shell
International Journal for Ignited Minds (IJIMIINDS) Determination of Burst Pressure of Spherical Shell Balaji J a & Shivappa H A b a PG Student, Dept. of Mechanical Engineering,Dr. Ambedkar Institute of
More informationPart 3 Pressure hull and structures Chapter 3 Pressure hull
RULES FOR CLASSIFICATION Underwater technology Edition December 2015 Part 3 and structures Chapter 3 The content of this service document is the subject of intellectual property rights reserved by ("DNV
More informationStress and deformation of offshore piles under structural and wave loading
Stress and deformation of offshore piles under structural and wave loading Author Eicher, Jackie, Guan, Hong, Jeng, Dong-Sheng Published 2003 Journal Title Ocean Engineering DOI https://doi.org/10.1016/s0029-8018(02)00031-8
More informationTresca s or Mises Yield Condition in Pressure Vessel Design
Tresca s or Mises Yield Condition in Pressure Vessel Design Franz Rauscher Institute for Pressure Vessels and Plant Technology Vienna University of Technology Austria Why using Tresca s yield condition
More informationDESIGN OF AN UNDERWATER TOWFISH USING DESIGN BY RULE AND DESIGN BY ANALYSIS
Proceedings of the ASME 204 Pressure Vessels & Piping Conference PVP204 July 20-24, 204, Anaheim, California, USA PVP204-2822 DESIGN OF AN UNDERWATER TOWFISH USING DESIGN B RULE AND DESIGN B ANALSIS Martin
More information2.1 Introduction to pressure vessels
2.1 Introduction to pressure vessels Pressure vessels in the form of cylinders and tanks are used for storing variety of liquids and gasses at different temperatures and pressures. Some of the substances
More informationDesign and optimization of a low pressure vessel
Abstract Research Journal of Engineering Sciences ISSN 2278 9472 Design and optimization of a low pressure vessel Available online at: www.isca.in, www.isca.me Received 8 th April 2017, revised 11 th July
More informationFEA ANALYSIS OF PRESSURE VESSEL WITHDIFFERENT TYPE OF END CONNECTIONS
FEA ANALYSIS OF PRESSURE VESSEL WITHDIFFERENT TYPE OF END CONNECTIONS Deval Nitin Bhinde 1 and Rajanarsimha S. 2 1 MTech CAD-CAM & Robotics, 2 Facculty, Department of Mechanical Engineering K.J. Somaiya
More informationPressurized Rescue Module System Hull and Transfer Skirt Design and Experimental Validation
Pressurized Rescue Module System Hull and Transfer Skirt Design and Experimental Validation C. Schoof, Ph.D., P.E. Cascadia Engineering LLC 24112 NE 29 th Street Sammamish, WA USA L. Goland, P.E. SouthWest
More informationIJSRD - International Journal for Scientific Research & Development Vol. 4, Issue 06, 2016 ISSN (online):
IJSRD - International Journal for Scientific Research & Development Vol. 4, Issue 06, 2016 ISSN (online): 2321-0613 Design Optimization and Fabrication of a Low Pressure Vessel Bhagatsinh Verma 1 Ankur
More informationDESIGN AND ANALYSIS OF PRESSURE VESSEL
DESIGN AND ANALYSIS OF PRESSURE VESSEL Vrushali Dilip Solapurkar 1 Assistant Professor, Mechanical Engineering Department, Vadodara Institute of Engineering, Gujarat, India ABSTRACT This technical paper
More informationDesign and Optimization of Weld Neck Flange for Pressure Vessel
V th International Symposium on Fusion of Science & Technology, New Delhi, India, January 18-22, 2016 ID: 2016-ISFT-430 Design and Optimization of Weld Neck Flange for Pressure Vessel Vinod Kumar 1, Vivek
More informationCONVECTION SECTION FAILURE ANALYSIS AND FITNESS-FOR-SERVICE ASSESSMENT
ASSET INTEGRITY INTELLIGENCE CONVECTION SECTION FAILURE ANALYSIS AND FITNESS-FOR-SERVICE ASSESSMENT JAMES R. WIDRIG, Manager Advanced Engineering at Quest Integrity Group VOLUME 23, ISSUE 6 NOVEMBER DECEMBER
More informationPVP2006-ICPVT
Proceedings of PVP2006 / ICPVT-11: 11 th International Conference on Pressure Vessel Technology July 23-37, 2006, Vancouver, Canada PVP2006-ICPVT11-93020 DESIGN OF A LARGE RECTANGULAR FLANGE Bharat Batra,
More informationOPENINGS AND REINFORCEMENTS 26
ASME BPVC.VIII.1-2015 UG-35.2 UG-36 (4) It is recognized that it is impractical to write requirements to cover the multiplicity of devices used for quick access, or to prevent negligent operation or the
More informationDesign and Analysis of an Unfired Pressure Vessel for Conducting Pressure Test
IJIRST International Journal for Innovative Research in Science & Technology Volume 4 Issue 3 August 2017 ISSN (online): 2349-6010 Design and Analysis of an Unfired Pressure Vessel for Conducting Pressure
More informationWorld Journal of Engineering Research and Technology WJERT
wjert, 2018, Vol., Issue 1, 334-340. Original Article ISSN 2454-695X Ashwini et al. WJERT www.wjert.org SJIF Impact Factor: 4.326 COMPARATIVE STUDY OF DIFFERENT TYPES OF END CLOSURES USED IN HORIZONTAL
More informationApplication of pushover analysis in estimating seismic demands for large-span spatial structure
28 September 2 October 2009, Universidad Politecnica de Valencia, Spain Alberto DOMINGO and Carlos LAZARO (eds.) Application of pushover analysis in estimating seismic demands for large-span spatial structure
More informationStructural analysis of a steel double hull underwater tank, intended for oil recovery from shipwrecks
76 Int. J. Computer Aided Engineering and Technology, Vol. 5, No. 1, 2013 Structural analysis of a steel double hull underwater tank, intended for oil recovery from shipwrecks D.E. Mazarakos, D.E. Vlachos
More informationIrrigation &Hydraulics Department lb / ft to kg/lit.
CAIRO UNIVERSITY FLUID MECHANICS Faculty of Engineering nd Year CIVIL ENG. Irrigation &Hydraulics Department 010-011 1. FLUID PROPERTIES 1. Identify the dimensions and units for the following engineering
More informationDesign and Structural Analysis of Cylindrical Shell
Design and Structural Analysis of Cylindrical Shell Lokesha 1, Chandan R 2, Byregowda K C 3 1 Department of Mechanical Engineering, Dr. Ambedkar Institute of Technology Bangalore, India 2,3 Assistant Prof.
More informationOffshore platforms survivability to underwater explosions: part I
Computational Ballistics III 123 Offshore platforms survivability to underwater explosions: part I A. A. Motta 1, E. A. P. Silva 2, N. F. F. Ebecken 2 & T. A. Netto 2 1 Brazilian Navy Research Institute,
More informationElastic-Plastic Finite Element Analysis for Zhongwei--guiyang Natural Gas Pipeline Endangered by Collapse
Abstract Elastic-Plastic Finite Element Analysis for Zhongwei--guiyang Natural Gas Pipeline Endangered by Collapse Gengxin Wu,Peng Zhang,Zhixiang Li,Zunhai Ke,Guizhi Li,Anmin Jiang 2 School of Civil Engineering
More informationPublished by: PIONEER RESEARCH & DEVELOPMENT GROUP (www.prdg.org) 113
Design, Develop And Analysis Of Effortless Pressure Regulator Considering Pressure Vessel Aspect M. B. Chopade 1, S.N. Khan2 1, 2 Mechanical (Design), Pune University Rajarshi Shahu College of Engineering,
More informationFINITE ELEMENT ANALYSIS: PRESSURE VESSEL WITH ANGULAR LEG SUPPORTS
Research Paper ISSN 2278 0149 www.ijmerr.com Vol. 3, No. 3, July, 2014 2014 IJMERR. All Rights Reserved FINITE ELEMENT ANALYSIS: PRESSURE VESSEL WITH ANGULAR LEG SUPPORTS Amit Patil* 1 and Amol Kolhe 2
More informationTHIN CYLINDERS AND SHELLS
CHAPTR 9 THIN CYLINDRS AND SHLLS Summary The stresses set up in the walls of a thin cylinder owing to an internal pressure p are: circumferential or hmp stress ah = longitudinal or axial stress al = -
More informationI. CHEM. E. SYMPOSIUM SERIES NO. 85
FIRE SURVIVAL OF PROCESS VESSELS CONTAINING GAS J. Nylund * The present work is a theoretical evaluation of the ability of process vessels to survive hydrocarbon fires when the vessels are designed and
More informationDesign of Pressure vessel for the Hydrocarbon release from the Vent Header Lines
Design of Pressure vessel for the Hydrocarbon release from the Vent Header Lines Bhargav Mangesh Joshi 1 1Student, Department of mechanical engineering, Modern college of engineering, Pune-5 ---------------------------------------------------------------------***---------------------------------------------------------------------
More informationSTRESS ANALYSIS OF PRESSURE VESSEL WITH DIFFERENT END CONNECTIONS
ISSN 2321-6441 STRESS ANALYSIS OF PRESSURE VESSEL WITH DIFFERENT END CONNECTIONS 1 APSARA C. GEDAM, 2 Dr. D. V. BHOPE 1 PG Student, M.Tech (CAD/CAM) R.C.E.R.T., Chandrapur (MH) 2 Professor, Department
More informationThe Relationship between the Depth Embedded Pipe Pile and the Force of Clamping Jaw
IOP Conference Series: Materials Science and Engineering PAPER OPEN ACCESS The Relationship between the Depth Embedded Pipe Pile and the Force of Clamping Jaw To cite this article: Yu Wentai et al 018
More informationExperimental Method to Analyse Limit Load in Pressure Vessel
International OPEN ACCESS Journal Of Modern Engineering Research (IJMER) Dilip M. Patel 1, Dr. Bimlesh Kumar 2 1 Mechanical Department D.N.Patel COE, Shahada 2 Mechanical Department COE, Faizpur Abstract:
More informationUse equation for the cylindrical section and equation or for the ends.
Solution 13.1 See section 13.3.4, equations 13.7 to 13.18 Solution 13.2 Use equation 13.34. (a) rigid constant C = 0.43 (b) free to rotate, C = 0.56 Solution 13.3 See section 13.5.1 Use equation 13.39
More informationLiquefied gas cargo tanks and process pressure vessels
.1 -.3 Liquefied gas cargo tanks and process pressure vessels.1 General.1.1 The present texts give the general principles which are applied by Classification Societies for approval and survey of the relevant
More informationASSESSMENT AND ANALYSIS OF PIPELINE BUCKLES
ASSESSMENT AND ANALYSIS OF PIPELINE BUCKLES GE Oil & Gas PII Pipeline Solutions Inessa Yablonskikh Principal Consultant Aberdeen, November, 14 th 2007 Assessment And Analysis Of Pipeline Buckles Introduction
More informationSTRUCTURAL ANALYSIS OF THE VACUUM VESSEL FOR THE LHCb VERTEX LOCATOR (VELO)
National Institute for Nuclear Physics and High Energy Physics Kruislaan 409 1098 SJ Amsterdam The Netherlands NIKHEF Reference no.: MT-VELO 04-1 EDMS no: 432626 OF THE VACUUM VESSEL FOR THE LHCb VERTEX
More informationPressure Vessel Design
We have made it easy for you to find a PDF Ebooks without any digging. And by having access to our ebooks online or by storing it on your computer, you have convenient answers with pressure vessel design.
More informationDesign and Analysis of Reactor Dish Vessel
IJIRST International Journal for Innovative Research in Science & Technology Volume 3 Issue 11 April 2017 ISSN (online): 2349-6010 Design and Analysis of Reactor Dish Vessel Aniket D. Patil PG Student
More informationDesign and Finite Element Analysis of Fabricated Panama chock with 225T capacity
LOWER HULL TOP DEC K EL. 3 1 ' - 2 " AB L [ 9 5 0 0 ] ( E) AIR DUC T ( INB D) ( E) B HD 1 4 m m `AH' ( E) PL. 1 2 m m `AH' ( E) L 1 5 0 x9 0 x1 2 m m `AH' - DO- - DO- SMIT BRACKET PANAMA CHOCK International
More informationASME Boiler & Pressure Vessel Code Analysis of the 1497 MHz High-Current Cryomodule Helium Vessel
1.0 Introduction ASME Boiler & Pressure Vessel Code Analysis of the 1497 MHz High-Current Cryomodule Helium Vessel Katherine Wilson 28 May 2007 To minimize the hazards associated with vacuum and pressure
More informationResearch Article Volume 6 Issue No. 6
DOI 10.4010/2016.1835 ISSN 2321 3361 2016 IJESC ` Research Article Volume 6 Issue No. 6 Design, Analysis and Development of Pressure Vessel Lug Support Vishal S. Telgote 1, Prof.G.E.Kondhalkar, Guide,
More informationThe Industrial Accident Resulted from the Failure of Bolt
The Industrial Accident Resulted from the Failure of Bolt Hyun Wook YEO 1, Jae Min LEE 2 and Sang Won CHOI 1, * 1 Occupational Safety and Health Research Institute, Korea Occupational Safety and Health
More informationProceedings of the ASME th International Conference on Ocean, Offshore and Arctic Engineering OMAE2011
Proceedings of the ASME 2011 30th International Conference on Ocean, Offshore and Arctic Engineering OMAE2011 June 19-24, 2011, Rotterdam, The Netherlands Proceedings of the ASME 2011 30th International
More informationAn Innovative Solution for Water Bottling Using PET
An Innovative Solution for Water Bottling Using PET A. Castellano, P. Foti, A. Fraddosio, S. Marzano, M.D. Piccioni, D. Scardigno* DICAR Politecnico di Bari, Italy *Via Orabona 4, 70125 Bari, Italy, scardigno@imedado.poliba.it
More informationKeywords: Stress, hemispherical end, flat circular end, ANSYS. liquids container, containment buildings for nuclear plant and so on. I.
ISSN XXXX XXXX 217 IJESC Research Article Volume 7 Issue No.5 Design, And Analysis of Pressure Vessel with Hemispherical and Flat Circular End RashmiKhobragade 1, VinodHiwase 2 M.Tech Student 1, Assistant
More informationStructural Analysis of Non Return Control Valve using Finite Element Analysis
Structural Analysis of Non Return Control Valve using Finite Element Analysis K. G. Saravanan Asst. Professor, Dept of Mechanical Engineering, Sona College of Technology, Salem, India N. Mohanasundara
More informationSTRUCTURE DESIGN AND CHARACTERISTIC ANALYSIS OF BUCKLING STRENGTH ON SWEDGE FRAME PRESSURE HULL WITH FINITE ELEMENT ANALYSIS
STRUCTURE DESIGN AND CHARACTERISTIC ANALYSIS OF BUCKLING STRENGTH ON SWEDGE FRAME PRESSURE HULL WITH FINITE ELEMENT ANALYSIS Ahmad Fauzan Zakki 1, Dong Myung Bae 2, Sulistiyono Susilo 1, Eli Akim Sipayung
More informationStress Analysis of The West -East gas pipeline with Defects Under Thermal Load
Stress Analysis of The West -East gas pipeline with Defects Under Thermal Load Abstract Xu Lei School of Petroleum Engineering, Yangtze University, Wuhan 430000, China 13071247220@163.com Natural gas is
More informationDESIGN OPTIMIZATION OF WORK ROLL CHOCK AND BACKUP ROLL CHOCK IN COLD ROLLING MILL
DESIGN OPTIMIZATION OF WORK ROLL CHOCK AND BACKUP ROLL CHOCK IN COLD ROLLING MILL Tukesh Sahu 1, Prof. G.R.Kesheory 2 1M.Tech Scholar, Department of Mechanical Engineering, VITS Indore, MP, India 2Assistant
More informationChapter 4: Single Vertical Arch
Chapter 4: Single Vertical Arch 4.1 Introduction This chapter considers a single pressurized arch in a vertical plane. This arch is similar to the arches that will be studied in the following chapter.
More informationσ = force / surface area force act upon In the image above, the surface area would be (Face height) * (Face width).
Aortic Root Inflation Introduction You have already learned about the mechanical properties of materials in the cantilever beam experiment. In that experiment you used bending forces to determine the Young
More informationSpecial Considerations for Structural design and Fabrication for. tankers or similar vessels with Large Size (150m or more in length) in.
Special Considerations for Structural design and Fabrication for tankers or similar vessels with Large Size (150m or more in length) in polar waters He. Guangwei Guangwei_ho@chinagsi.com Mai. Rongzhi MRZ@chinagsi.com
More informationRULES PUBLICATION NO. 20/P SHIP SIDE STRENGTHENING OF FISHING VESSELS MOORING AT SEA ALONGSIDE OTHER VESSELS
RULES PUBLICATION NO. 20/P SHIP SIDE STRENGTHENING OF FISHING VESSELS MOORING AT SEA ALONGSIDE OTHER VESSELS 1995 Publications P (Additional Rule Requirements), issued by Polski Rejestr Statków, complete
More information5605 (726:MAK:lkg) Ser October yection. .IN% 7""~ipj~ls(j 1-1. I II I rr. 9110/Subs
V393.R46 ".4 rl -. 51,:hL,- DEPARTMENT OF THE NAVY DAVID TAYLOR MODEL BASIN WASHINGTON 7, D.C. IN REPLY REFER TO 9110/Subs 5605 (726:MAK:lkg) Ser 7-376 26 October 1962 From: To: Subj: Encl: Commanding
More informationFigure 1 FSM 250 roof anchor system
Report No.: 15111045 Date: 27.11.15 Engineers Report FSM 250 Roof Anchor Overview Methodology AS/NZS 1891.4:2009 Loading Anchorage Application Analysis Parameters Acceptance Criteria Results Conclusions
More informationAnalysis of Shear Lag in Steel Angle Connectors
University of New Hampshire University of New Hampshire Scholars' Repository Honors Theses and Capstones Student Scholarship Spring 2013 Analysis of Shear Lag in Steel Angle Connectors Benjamin Sawyer
More informationDesign and Analysis of Pressure Vessel with different end domes
Design and Analysis of Pressure Vessel with different end domes Merlin J. Thattil, Chitaranjan Pany Abstract - In this paper, pressure vessel with different end domes (torispherical and hemispherical),
More informationDesign and Analysis of Pressure Safety Release Valve by using Finite Element Analysis
Design and Analysis of Pressure Safety Release Valve by using Finite Element Analysis Mr.V.D.Rathod* 1, Prof.G.A.Kadam* 2, Mr.V. G. Patil* 3 * 1 M.E. Design (Pursuing), SKN Sinhgad Institute of Technology&
More informationStep 1: Step 2: psi psi
General Tutorial on Evaluation of Nozzles by computing Local Shell Stresses as per WRC 537 and Stress Evaluation as per ASME Section VIII Division 2 using CAEPIPE Whenever Pressure Vessel or Heat exchanger
More informationModelling and Equivalent Stress Analysis of Flat Dish End Pressure Vessel
International Journal of Current Engineering and Technology E-ISSN 2277 4106, P-ISSN 2347 5161 2015 INPRESSCO, All Rights Reserved Available at http://inpressco.com/category/ijcet Research Article Modelling
More informationDESIGN AND DEVELOPMENT OF A RIG FOR THE PRESSURE TESTING OF WEAK VESSELS AND SUBSEQUENT WORK RELATING TO THE STRENGTH OF FLAT PLATES
DESIGN AND DEVELOPMENT OF A RIG FOR THE PRESSURE TESTING OF WEAK VESSELS AND SUBSEQUENT WORK RELATING TO THE STRENGTH OF FLAT PLATES D.F. Pilkington Ph.D. B.Sc(Eng)*, G Piatt B.Sc.*, G. Norton B.Sc.**
More informationInternational Journal of Scientific & Engineering Research, Volume 6, Issue 9, September-2015 ISSN
827 MEMS PRESSURE RELIEF VALVE: DESIGN, MODEL AND STATIC ANALYSIS Anand M. Shelke, Amit Cherian, Sandesh A. Ghate Guided by Prof. DRS Raghuraman M.Tech (Mechatronics) School of Mechanical and Building
More informationSTUDY OF UNDERWATER THRUSTER (UT) FRONT COVER OF MSI300 AUTONOMOUS UNDERWATER VEHICLE (AUV) USING FINITE ELEMENT ANALYSIS (FEA)
STUDY OF UNDERWATER THRUSTER (UT) FRONT COVER OF MSI300 AUTONOMOUS UNDERWATER VEHICLE (AUV) USING FINITE ELEMENT ANALYSIS (FEA) M. Sabri 1, 2, T. Ahmad 1, M. F. M. A. Majid 1 and A. B. Muhamad Husaini
More informationAdaptive Pushover Analysis of Irregular RC Moment Resisting Frames
Kalpa Publications in Civil Engineering Volume 1, 2017, Pages 132 136 ICRISET2017. International Conference on Research and Innovations in Science, Engineering &Technology. Selected papers in Civil Engineering
More informationMSC Guidelines for Review of Gas Carrier/Barge Structures
R. J. LECHNER, CDR, Tank Vessel and Offshore Division Purpose To establish a process for requesting structural plan review approval for a gas carriers/independent pressure tank barges regulated under 46
More informationDesign and Optimization ofpressure Vessel
ISSN 2395-1621 Design and Optimization ofpressure Vessel #1 J.Ahmad, #2 A.K.Pathak 1 junaidahm92@gmail.com 2 ajay2628@gmail.com #12 Department of Mechanical Engineering, D. Y. Patilcollege of Engineering,
More informationVertical Uplift Capacity of a Group of Equally Spaced Helical Screw Anchors in Sand
SECM/15/080 Vertical Uplift Capacity of a Group of Equally Spaced Helical Screw Anchors in Sand S. Mukherjee 1* and Dr. S. Mittal 2 1 Amity University, Noida, India 2 Indian Institute of Technology, Roorkee,
More informationSEALANT BEHAVIOR OF GASKETED-SEGMENTAL CONCRETE TUNNEL LINING
4 th International Conference on Earthquake Geotechnical Engineering June 25-28, 2007 Paper No.1636 SEALANT BEHAVIOR OF GASKETED-SEGMENTAL CONCRETE TUNNEL LINING Faisal SHALABI 1, Edward CORDING 2, and
More informationRudder Investigation. By Harish M
Rudder Investigation By Harish M Where and on What? Series of RO RO Vessels designed and constructed by Flensberger Schiffbau Gesselshaft GmbH. Rudders independently manufactured by Macor Neptun GmbH.
More informationISSN: Page 410
Study of Structural Stability of Globe Valve in Petroleum and Sugar Industries Anil Rathod 1, Dr. S N Kurbet 2 1 PG Student Mechanical branch (machine Design) BEC Bagalkot, Karnataka India, 2 HOD of Mechanical
More informationStudy to Establish Relations for the Relative Strength of API 650 Cone Roof Roof-to-Shell and Shell-to- Bottom Joints
Thunderhead Engineering Consultants I N C O R P O R A T E D 1006 Poyntz Ave. Manhattan, KS 66502-5459 785-770-8511 www. thunderheadeng.com Study to Establish Relations for the Relative Strength of API
More informationDAMAGE TO STORAGE TANKS CAUSED BY THE 2011 TOHOKU EARTHQUAKE AND TSUNAMI AND PROPOSAL FOR STRUCTURAL ASSESSMENT METHOD FOR CYLINDRICAL STORAGE TANKS
DAMAGE TO STORAGE TANKS CAUSED BY THE 2011 TOHOKU EARTHQUAKE AND TSUNAMI AND PROPOSAL FOR STRUCTURAL ASSESSMENT METHOD FOR CYLINDRICAL STORAGE TANKS Takashi Ibata Isho Nakachi Dr. Kazuo Ishida Junichi
More information[Hussain*, 4.(7): July, 2015] ISSN: (I2OR), Publication Impact Factor: 3.785
IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY DESIGN OF ULTRA HIGH VACUUM (UHV) SYSTEM TO EVALUATE OUTGASSING RATE OF THE MATERIALS TO ASSES THEIR UHV COMPATIBILITY Ibrahim
More informationHigh-Level Study on the Potential Impact of Rollers on Subsea Power Cables
REPORT ENGINEERING REPORT Title: High-Level Study on the Potential Impact of Rollers on Subsea Power Cables Project: C56808 Client: European Subsea Cables Association Document Control Revision Date Document
More informationIf searching for a ebook by John E Gibson Computer analyses of cylindrical shells;: Design tables for cylindricl shell roofs calculated by automatic
Computer Analyses Of Cylindrical Shells;: Design Tables For Cylindricl Shell Roofs Calculated By Automatic Digital Computer (Spon's Civil Engineering Series) By John E Gibson READ ONLINE If searching for
More informationUKOPA Dent Management Strategy
UKOPA Dent Management Strategy 1 Background Pipelines are thin shell structures which are susceptible to geometric distortions and dents during handling, construction, and operation. These dents and distortions,
More information[Barve, 4(7): July, 2015] ISSN: (I2OR), Publication Impact Factor: 3.785
IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY PARAMETRIC STUDY TO UNDERSTAND THE SEISMIC BEHAVIOUR OF INTZE TANK SUPPORTED ON SHAFT Prasad S. Barve *, Ruchi P. Barve * Civil
More informationModeling of thin strip profile during cold rolling on roll crossing and shifting mill
University of Wollongong Research Online Faculty of Engineering and Information Sciences - Papers: Part A Faculty of Engineering and Information Sciences 2013 Modeling of thin strip profile during cold
More informationEffect of Wind Load on Pressure Vessel Design by Using Non- Linear Finite Element Analysis (FEA)
Effect of Wind Load on Pressure Vessel Design by Using Non- Linear Finite Element Analysis (FEA) Sandip S. Chavan * Sanjay H. Kalaskar ** Pradip B. Patil *** Assistant Professor, Mechanical Engineering
More information2003 WJTA American Waterjet Conference August 17-19, 2003 Houston, Texas Paper PIPE THREADS-WHAT IS THE LIMIT?
23 WJTA American Waterjet Conference August 17-19, 23 Houston, Texas Paper PIPE THREADS-WHAT IS THE LIMIT? D. Wright, J. Wolgamott, G. Zink StoneAge, Inc. Durango, Colorado, U.S.A. ABSTRACT At present
More informationDesign of LPG mould billet using FEM
Design of LPG mould billet using FEM R. Datha Satyanarayana P.G Student, Department of Mechanical Engineering, Chaitanya College of Engineering. ABSTRACT: The significance of the title of the project comes
More informationR.J.P. BARKER AND S.D. GUEST Cambridge University Engineering Department Trumpington Street, Cambridge CB2 1PZ, UK
INFLATABLE TRIANGULATED CYLINDERS R.J.P. BARKER AND S.D. GUEST Cambridge University Engineering Department Trumpington Street, Cambridge CB2 1PZ, UK Abstract A study is described into the use of triangulated
More informationAnalysis of dilatometer test in calibration chamber
Analysis of dilatometer test in calibration chamber Lech Bałachowski Gdańsk University of Technology, Poland Keywords: calibration chamber, DMT, quartz sand, FEM ABSTRACT: Because DMT in calibration test
More informationRotary air valves used for material feed and explosion protection are required to meet the criteria of NFPA 69 (2014)
Rotary air valves used for material feed and explosion protection are required to meet the criteria of NFPA 69 (2014) 12.2.4.2. 12.2.4.2 rotary valve design criteria (close clearance) 12.2.4.3 THE DESIGN
More informationThe Use of ILI In Dent Assessments
The Use of ILI In Dent Assessments Prepared for: 2014 CRUG Conference Date: 11 September 2014 Prepared by: Rhett Dotson, PE Contributions from Dr. Chris Alexander and Markus Ginten Contents Current Dent
More information