Standard Operating Manual
|
|
- Joseph McBride
- 6 years ago
- Views:
Transcription
1 Standard Operating Manual Denton Explorer 14 RF/DC Sputter Version 1.0 Page 1 of 11
2 Contents 1. Picture and Location 2. Process Capabilities 1. Cleanliness Standard 2. Available for Sputtering Materials 3. Performance of the Denton Explorer 14 RF/DC Sputter 3. Contact List and How to Become a Qualified User 1. Emergency Responses and Communications 2. Training to Become a Qualified Denton Explorer 14 RF/DC Sputter User 4. Operating Procedures 1. System Description 2. Safety Warnings 3. Operation Rules 4. Initial System Checks 5. Status Checks 6. Venting the Chamber (Before Loading Wafers) 7. Inspecting the Chamber Before Use 8. Load Wafers 9. Pumping Down the System for Sputtering 10. Start your Sputtering Process 11. Venting the Chamber (Before Unloading Wafers) 12. Pumping Down the Systen for Idle Version 1.0 Page 2 of 11
3 Denton Explorer 14 RF/DC Sputter Cathode #3 Picture and Location Cathode #1 Cathode #2 Main Chamber RF Power Readout Denton Explorer 14 RF/DC Sputter Ar Gas Valve DC Power Readout Version 1.0 Page 3 of 11
4 Display ON/OFF Switch (RF Power) ON/OFF Switch (DC Power) This tool is located at NFF Enterprise Center Cleanroom Room 4162 Version 1.0 Page 4 of 11
5 Process Capabilities Cleanliness Standard Denton Explorer 14 RF/DC Sputter is Non-Standard equipment for DC and RF sputtering process of metals. Available for Sputtering Materials The following sources are available in Denton Explorer 14 RF/DC Sputter. Denton Explorer 14 RF/DC Sputter: Ti, TiW, Ag, Al (pure), AlSi and Cu for 2 to 4 wafer or small piece sample. NOTE: Consult a NFF EC staff member prior to do new materials other than above listed materials. Hazardous or Radioactive materials are not allowed to be sputtered in Denton Explorer 14 RF/DC Sputter. Performance of the Denton Explorer 14 RF/DC Sputter What the Denton Explorer 14 RF/DC Sputter CAN do Denton Explorer 14 can provide to sputter thin films thickness ( 50A thick) or thick films thickness ( 1.5um thick). Thin films: Ti, TiW and Ag. Thick films: Al (pure), AlSi and Cu. Denton Explorer 14 is suitable up to 4 wafer or small piece sample. What the Denton Explorer 14 RF/DC Sputter CANNOT do Denton Explorer 14 RF/DC Sputter should not be used for replacement of VARIAN 3180 and CVC-601 to sputter thick films, e.g. over 1.5um Denton Explorer 14 RF/DC Sputter should not be used for dielectric material sputtering. Users cannot modify the recipes, such as process minimum vacuum, cathode power (RF/DC), ignition pressure, argon gas flow, please consult NFF EC Version 1.0 Page 5 of 11
6 staff member. Process time is not allowed for longer than 400 seconds per run and there should be 10 minutes for chamber cooling. Contact List and How to Become a User Emergency Responses and Communications Security Control Center: (24hr) & (24hr) Safety Officer: Mr. Wing Leong CHUNG & Deputy Safety Officer: Mr. Man Wai LEE & NFF EC Technician: Mr. Peter Yiu Cheong PUN & NFF Phase 2 Technician: Mr. Wilson Pui Keung YIP Training to Become a Qualified Denton Explorer 14 RF/DC Sputter User Please follow the procedures below to become a qualified user of Denton Explorer 14 RF/DC Sputter. 1. Read all materials posted on the NFF website about Denton Explorer 14 RF/DC Sputter. 2. Send an to Mr. Peter PUN requesting Denton Explorer 14 RF/DC Sputter safety operation training. Schedule of training will be informed within several weeks, depending on number of requests. Operating Procedures System Description Denton Explorer 14 RF/DC Sputter is a sputtering system installed with three targets and it allows single layer and multilayer processes. One of the cathodes is energized by a radio frequency (RF) power source whereas the other two are direct current (DC) Version 1.0 Page 6 of 11
7 powered. This means that the RF/DC cathodes can sputter from conductive targets. A large collection of targets is available for this sputtering system but obviously, only three can be installed at any given time. In the event that a target is required which is not currently installed in the sputtering system, the user must submit a target change request via or phone to NFF EC staff. The request must be submitted at least 2 days prior to needing the target. Emergency off and Interlock facilities Emergency Stop is provided to shut down the sputtering system in an emergency. An emergency off switch, with normally-closed contacts, is mounted on bottom of the console. The switch is activated by pressing a 40mm diameter red Emergency Stop button. PLC interlock chain The interlock chain is monitored by the software, but acts independently. It is also supplemented by machine protection sensors, which operate only via the software. Safety Warnings This equipment can cause injury if not used in a cautious manner. 1. Do not operate the system if any of the doors, panels or covers is removed. 2. Ensure that all personnel who operate this equipment are trained to use the equipment, and are alerted to the range of hazards present. 3. When opening the chamber, ensure that personnel stand clear of the chamber door. 4. Close chamber door carefully, ensure that personnel vacate the vicinity of the door and its operating mechanism before it is closed to avoid trapped fingers etc. 5. Ensure that you do not leave tweezers from the chamber, damage the turbo pump could occur. 6. If the sample to be sputtered contains thin film photo resist for liftoff, then the Version 1.0 Page 7 of 11
8 substrate must be baked immediately before placing it in the chamber. Operation Rules 1. If an equipment failure while being used, never try to fix the problem by yourself. Please contact NFF staff. 2. Do not operate equipment unless you are properly trained and approved by NFF staff. 3. Do not leave an on-going experiment unattended. 4. Do not run sputtering process for long than 400 seconds per run. 5. Should be at least ten minutes for chamber cooling after sputtering process or in between two processes. Initial system checks 1. Verify that the needed targets have been installed in the chamber. The targets currently installed can be checked on the log sheet or via correspondence with NFF EC staff. 2. If the required targets are not in place, submit a target change request via or phone to NFF EC staff. The request must be submitted at least 2 days prior to needing the target. 3. Review the desired recipe to check that every parameter is set as required, especially the deposition time which determines the coating thickness. Status checks 1. Check the NFF website for reservations, problems and to see if it is already occupied by other users. 2. Check for an EMPTY sign attached to the machine. Do not use if an IN USE signs or MAINTENANCE sign is there. Check for problem notes. 3. The system is available if the initial system and status checks are normal. Check-in the equipment and enable the system on NFF Machine Reservation System. Place sign IN USE on the machine. Version 1.0 Page 8 of 11
9 Venting the Chamber (Before Loading Wafers) 1. Make sure that the system is not in the service mode position. 2. Turn off all internal sources of power (RF power and DC power). 3. Select the Auto Control screen indicator. 4. Select the Auto Vent indicator button. 5. System status will display Auto Mode. 6. Chamber will safely vent to atmospheric pressure. Inspecting the chamber before Sputtering 1. Review the previous entry in logbook to ensure there are no reported problems. 2. Fill in the log sheet with your name, NFF project number, reservation timeslot, source, thickness, RF power, DC Bias, gases flow rate and processing time being used. 3. Minimize time that the chamber opens. Load wafers 1. Place your sample to face upward in the center of the substrate holder. Before beginning, be sure to wear gloves to reduce contamination and to protect the hands. 2. Allow to load 3 pieces of 4 full wafers (100mm) at the same time. 3. Check the O-ring of the chamber lid to ensure that they are free of particles, dirt and not damaged. Pumping Down the System for Sputtering To pump down the system, use the following procedures: 1. Make sure the system is NOT in Service mode. 2. Select the Auto Control screen indicator. 3. Select the Auto Pump indicator button. 4. System Status will display Auto Mode. 5. System will safely pump from atmosphere to high vacuum. 6. The base pressure is 6e-06 Torr. Version 1.0 Page 9 of 11
10 Remark: Turning off the rough pump will cause all process and pumping actions using that pump to stop. Start your Sputtering Process Automatic Process Run: 1. Make sure in System Control page, press the Auto Control button, select Auto Pump button for pump down the system. 2. Check that the system has pumped down to base pressure. (The base pressure is 6e-06 Torr). 3. Auto RF/DC Sputtering is the easiest and fastest procedure overall. However, note that the Pre-Sputter Time and Sputter Time vary with different sputtering material and output power. You can select Auto Control button and then select Auto Setup button to modify the Pre-Sputter and Sputter time. 4. Make sure you will select RF or DC sputtering process. 5. Ensure to turn on DC power supply (XANTREX, XFR 600) when you choose DC sputtering process. 6. Otherwise, when you choose RF sputtering process, please turn on RF Generator (SEREN R MHz) and RF Automatic Matching Network Controller (SEREN MC 2 ). 7. And then press Close button to return to Auto Control page. 8. Select desired Cathode number (1, 2 or 3) and then press Auto Process for start your sputtering process. 9. Until the process completed, please give 10 minutes for chamber and target cooling. 10. Then turn off DC power supply or RF Generator and RF Automatic Matching Network Controller. 11. Press Auto Control button and select Auto Vent button for chamber vent. 12. Until the pressure has reached to atmospheric pressure, open the chamber door for unloading your samples. 13. Close the chamber door and press Auto Pump to pump down the system. Version 1.0 Page 10 of 11
11 Venting the Chamber (Before Unloading Wafers) 1. Ensure that the system is not in service mode position. 2. Turn off all internal sources of power (RF power and DC power). 3. Select the Auto Control screen indicator. 4. Select the Auto Vent indicator button. 5. Chamber will safely vent to atmospheric pressure. Pumping Down the System for Idle To pump down the system, use the following procedures: 1. After unloading the samples, close the process chamber door and lock the door. 2. Ensure that the System Control screen is displayed. 3. Ensure that the system status is displayed at Auto Mode. 4. Then select the Auto Control button and press Auto Pump button for system pump from atmosphere to high vacuum. 5. Ensure that the status indicators (Vacuum/Skin/Door/Water/Crossover Switches/Turbo at speed/minimum Vacuum) are in green color. 6. DON T GO AWAY YET! 7. Monitor the pressure to make sure that the base pressure can reach to 6e-05 Torr. 8. Clean up the area and move the items back to their proper positions. 9. Place an EMPTY sign on the machine. 10. Fill in the logbook, completely noting any problems. Remark: Turning off the rough pump will cause all process and pumping actions using that pump to stop. Version 1.0 Page 11 of 11
Standard Operating Manual
Standard Operating Manual Oxford Plasmalab 80 Plus Plasma Etcher Page 1 of 24 Contents 1. Picture and Location 2. Process Capabilities 2.1 Cleanliness Standard 2.2 Available Etching Materials 2.3 Performance
More informationStandard Operating Manual
Standard Operating Manual Branson IPC 3000 O 2 Asher Page 1 of 14 Contents 1 Picture and Location 2 Process Capabilities 2.1 Cleanliness Standard 2.2 Recipes 2.3 Performance of Branson IPC 3000 O 2 Asher
More informationStandard Operating Manual
Standard Operating Manual Allwin21 AW610 RTP Page 1 of 18 Contents 1 Picture and Location 2 Process Capabilities 2.1 Cleanliness Standard 2.2 Recipes 2.3 Performance of Allwin21 AW610 RTP 3 Contact List
More informationStandard Operating Manual
Standard Operating Manual Branson IPC 3000 O 2 Asher Copyright 2014 by Hong Kong University of Science & Technology. All rights reserved. Page 1 Contents 1. Picture and Location 2. Process Capabilities
More informationStandard Operating Manual
Standard Operating Manual ARC12M Sputter Copyright 11.2015 by Hong Kong University of Science & Technology. All rights reserved. Page 1 Contents 1. Picture and Location 2. Process Capabilities 2.1 Cleanliness
More information5.1.3 Mechanical Hazards Drive assemblies have sufficient power to cause injury. Keep hands, fingers, clothing and tools clear of moving parts.
Approved by: Process Engineer / / / / Equipment Engineer 1 SCOPE The purpose of this document is to detail the use of the PE4400. All users are expected to have read and understood this document. It is
More informationOerlikon Sputtering Evaporator SOP
Oerlikon Sputtering Evaporator SOP Short UNT Cleanroom 1. Taking out sample holder from Transport Chamber : Log in FOM to access the software Go to the software and log in with user1 and password user1
More information1.1 Equipment: substrate, wafer tweezers, metal targets 1.2 Personal Protective Equipment: nitrile gloves, safety glasses 1.
Nanomaster NSC-3000 DC Magnetron Sputter Tool Standard Operating Procedure Faculty Supervisor: Prof. Robert White, Mechanical Engineering (x72210) Safety Office: Peter Nowak x73246 (Just dial this directly
More informationUnaxis ICP/RIE SOP Revision 8 09/30/16 Page 1 of 5. NRF Unaxis ICP/RIE Etch SOP
Page 1 of 5 NRF Unaxis ICP/RIE Etch SOP Unaxis Shuttlelock Reactive Ion Etcher with Inductively Coupled Plasma Module. Etch Capabilities: SiO2, Si3N4, Al, dielectrics and other commonly used materials.
More informationUnifilm Technology PVD-300 Sputter Deposition Operation Instructions
Unifilm Technology PVD-300 Sputter Deposition Operation Instructions Contributors: Devin Brown, Kevin Klein, Ben King, Eric Woods Anything that is BOLD UNDERLINED ITALICS means that you should press that
More informationNordiko Metal Sputtering System Standard Operating Procedure
Nordiko Metal Sputtering System Standard Operating Procedure Specifications : Target Size Gases used in the system Base pressure Sputtering pressure Substrates used Substrate size : 2 inch or 4 inch :
More informationIssue: H Title: CHA E-Beam Evaporator Page 1 of 7. Table of Contents
Title: CHA E-Beam Evaporator Page 1 of 7 Table of Contents Purpose/Scope... 2 2.0 Reference Documents... 2 3.0 Equipment/Supplies/Material... 2 4.0 Safety... 2 5.0 Set Up Procedures... 2 5.1 PC Logon and
More informationJETFIRST 150 RTA SYSTEM OPERATING MANUAL Version: 2 Feb 2012
JETFIRST 150 RTA SYSTEM OPERATING MANUAL Version: 2 Feb 2012 UNIVERSITY OF TEXAS AT ARLINGTON Nanofabrication Research and Teaching Facility TABLE OF CONTENTS 1. Introduction....2 1.1 Scope of Work.....2
More informationStandard Operating Manual
Standard Operating Manual AB-M Mask Aligner Version 1.1 Page 1 of 18 Contents 1. Picture and Location 2. Process Capabilities 2.1 Cleanliness Standard 2.2 Wafer Chuck Selection 2.3 Mask Holder Selection
More informationSPUTTER STATION STANDARD OPERATING PROCEDURE
SPUTTER STATION STANDARD OPERATING PROCEDURE Purpose of this Instrument: This instrument is used for deposition of thin metal or oxide films. Source materials supplied by WVU Shared Research Facilities:
More informationBasic ICP Operating Procedures
Center for High Technology Materials 2 February, 2009 University of New Mexico Created by Beth Fuchs Basic ICP Operating Procedures INTRODUCTION: The ICP is an inductively coupled plasma etching system,
More informationOperating Procedures for Metal Evaporator I
Operating Procedures for Metal Evaporator I Metal Evaporator I is intended as a tool and a training device. Understanding the operation of this equipment should give you a basic knowledge of vacuum and
More informationOXFORD PLASMALAB 80PLUS (CLOEY)
Arizona State University NanoFab OXFORD PLASMALAB 80PLUS (CLOEY) Rev D Table of Contents Contents Table of Contents...1 1. Purpose / Scope...2 2. Reference Documents...2 3. Equipment / Supplies / Material...2
More informationPLASMA ENHANCED CHEMICAL VAPOR DEPOSITION (PECVD) SOP OXFORD PLASMALAB SYSTEM 100
PLASMA ENHANCED CHEMICAL VAPOR DEPOSITION (PECVD) SOP OXFORD PLASMALAB SYSTEM 100 June 2013 Interface Overview. The Oxford software is divided into 5 main screens. 1) Pump Control page 2) Recipe page 3)
More informationSTS PECVD Instructions
STS PECVD Instructions I. Introduction A PECVD (Plasma Enhanced Chemical Vapor Deposition) reacts gases in a RF- (Radio Frequency) - induced plasma to deposit materials such as SiO 2 and Si X N Y. This
More informationStandard Operating Manual
Standard Operating Manual Fisher Scientific Isotemp TM Model 281A Vacuum Oven Version 1.1 Page 1 of 9 Contents 1. Picture and Location 2. Process Capabilities 2.1 Cleanliness Standard 2.2 Substrate Size
More informationUsage Policies Notebook for NanoFurnace Furnace (EasyTube 3000 System)
Usage Policies Notebook for NanoFurnace Furnace (EasyTube 3000 System) Revision date October 2014 2 Emergency Plan for Nano Furnace Standard Operating Procedures for Emergencies Contact information Person
More informationEdge Isolation Tool. Standard Operating Procedure. Version 1.1. Date: Prepared by, Sandeep S S. Department of Electrical Engineering
Edge Isolation Tool Standard Operating Procedure Version 1.1 Date: 20-9-2012 Prepared by, Sandeep S S Department of Electrical Engineering IIT Bombay This document is meant for internal circulation only
More informationArizona State University Center for Solid State Electronic Research. Table of Contents. Issue: C Title: Oxford Plasmalab 80plus (Floey) Page 1 of 8
Title: Oxford Plasmalab 80plus (Floey) Page 1 of 8 Table of Contents 1.0 Purpose/Scope... 2 2.0 Reference Documents... 2 3.0 Equipment/Supplies/Material... 2 4.0 Safety... 2 5.0 Set Up Procedures... 2
More informationRevised: June 7, 2017
LC Technologies Thermal Evaporator Standard Operating Procedure Faculty Supervisor: Prof. Robert White, Mechanical Engineering (x72210) Safety Office: Peter Nowak x73246 (Just dial this directly on any
More informationMJB4 Mask Aligner Operating Procedure. Effective Date: 07/12/2012 Author(s): Jiong Hua Phone:
MJB4 Mask Aligner Operating Procedure Effective Date: 07/12/2012 Author(s): Jiong Hua Phone: 402-472-3773 Email: jhua2@unl.edu 1 1 Introduction 1.1 Key Words Karl Suss MJB4 Mask Aligner, Optical Lithography,
More informationUsage Policies Notebook for AMST Molecular Vapor Deposition System MVD 100
Usage Policies Notebook for AMST Molecular Vapor Deposition System MVD 100 Revision date September 2014 2 Emergency Plan for AMST MVD 100 Standard Operating Procedures for Emergencies Contact information
More informationNanofabrication Facility: ECR Etcher SOP Rev. 01b, March 06. Standard Operating Procedure for PlasmaQuest ECR II Etching
Standard Operating Procedure for PlasmaQuest ECR II Etching Authors: Rev. 00: Al Schmalz, Vighen Pacradouni and Jeff Young, December 21, 1998 Rev. 01: Dr. Andras G. Pattantyus-Abraham, May 24, 2005 Rev.
More informationUsage Policies Notebook for Trion RIE / ICP Dry Etch
Usage Policies Notebook for Trion RIE / ICP Dry Etch Revision date September 2014 2 Emergency Plan for Trion RIE/ICP Dry Etch Standard Operating Procedures for Emergencies Contact information Person Lab
More informationUnaxis PECVD. SiH4 (5% in He)
Unaxis PECVD Table of Contents: I: Introduction II: Machine Specifications III: System Components IV: Deposited Materials and Precursor Gases V: Operating Instructions VI: Creating a Recipe VII: Troubleshooting
More informationCOMELEC C-30-S Parylene Coating System
COMELEC C-30-S Parylene Coating System Comelec C-30-S Parylene deposition system Introduction Parylene is a polymere deposited at room temperature in a vacuum chamber (few µb). Parylene coating is perfectly
More informationAngstrom E-Beam Instructions. PROCESS CHECKS: the tooling factors of each metal; Ti/Au layer for wire bonding pull test.
Angstrom E-Beam Instructions Tool Manager: Joe Palmer (jpalmer@princeton.edu) Office: 8-4706; Cell:609-751-1353 Backup: David Barth (dbarth@princeton.edu) Office: 8-4626; Cell: 610-405-8227 PROCESS CHECKS:
More informationR I T. Title: STS ASE Semiconductor & Microsystems Fabrication Laboratory Revision: Original Rev Date: 01/21/ SCOPE 2 REFERENCE DOCUMENTS
Approved by: Process Engineer / / / / Equipment Engineer 1 SCOPE The purpose of this document is to detail the use of the STS ASE. All users are expected to have read and understood this document. It is
More informationQUORUM TECH 150RES THE FIRST AND THIRD WEEK WILL BE SET UP FOR CARBON COATING THE SECOND AND LAST WEEK WILL BE SET UP FOR GOLD COATING
QUORUM TECH 150RES This document is intended to describe the function and use of the QuorumTech Q150RES system. Formal training and qualification by staff is required before gaining access to the tool.
More informationUsage Policies Notebook for Parylene Coating System
Usage Policies Notebook for Parylene Coating System Revision date September 2014 2 Emergency Plan for Parylene Coating System Standard Operating Procedures for Emergencies Contact information Person Lab
More informationNotes-PECVD: Chamber 1
plasmatherm (EML) STANDARD OPERATING PROCEDURE CORAL Name: Plasmatherm Model Shuttlelock System VII SLR-770/734 Number: Location: EML What it Deposits the following films via Plasma-Enhanced Chemical Vapor
More informationR I T. Title: Amray 1830 SEM Semiconductor & Microsystems Fabrication Laboratory Revision: A Rev Date: 09/29/03 1 SCOPE 2 REFERENCE DOCUMENTS
Fabrication Laboratory Revision: A Rev Date: 09/29/03 Approved by: Process Engineer / / / / Equipment Engineer 1 SCOPE The purpose of this document is to detail the use of the Amray 1830 SEM. All users
More informationUniversity of MN, Minnesota Nano Center Standard Operating Procedure
Equipment Name: University of MN, Minnesota Nano Center Deep Trench Etcher Badger Name: deeptrench Revision Number: 9 Model: SLR -770 Sofware Version: CORTEX v4.5 Revisionists: Paul Kimani Location: Bay
More informationUniversity of MN, Minnesota Nano Center Standard Operating Procedure
Equipment name: STS Etcher Badger name: STS Revision number: 3 Model: 320 Revisionist: Paul Kimani Location: Bay 3 Date: 1 October 2013 A. Description The 320 is a manually loaded batch plasma etching
More informationAngstrom Dielectric Sputterer Operation Manual
Angstrom Dielectric Sputterer Operation Manual I. System overview The Angstrom Dielectric Sputterer (ADS) has a similar interface as the Angstrom metal sputterer. It has two screens, the process screen
More informationUsage Policies Notebook for Xenon Difluoride (XeF 2 ) Isotropic Si Etch
Usage Policies Notebook for Xenon Difluoride (XeF 2 ) Isotropic Si Etch Revision date September 2014 2 Emergency Plan for XeF 2 Si Etcher Standard Operating Procedures for Emergencies Contact information
More informationArizona State University NanoFab PLASMATHERM 790 RIE. Version A
rizona State University NanoFab PLSMTHERM 790 RIE Version SU NanoFab Title: PLSMTHERM 790 RIE Table of Contents Contents Table of Contents...1 1. Purpose / Scope...2 2. Reference Documents...2 3. Equipment
More informationPlasma Asher: March PX-500 User guide (May-30, 2017)
Plasma Asher: March PX-500 User guide (May-30, 2017) This is a highly versatile plasma etch tool that can etch using a direct plasma configuration (Oxygen plasma cleaner), a downstream plasma (Remote plasma),
More informationSSI Solaris 150 RTA Revision /27/2016 Page 1 of 9. SSI Solaris 150 RTA
Page 1 of 9 SSI Solaris 150 RTA The Solaris 150 RTA is a rapid thermal annealing system capable of handling sample sizes up to 100mm (4 diameter) or smaller. The system can anneal in N 2 and Forming gas
More informationTrion PECVD SOP IMPORTANT: NO PLASTIC, TAPE, RESISTS, OR THERMAL PASTE ARE ALLOWED IN THE CHAMBER
Trion PECVD SOP IMPORTANT: NO PLASTIC, TAPE, RESISTS, OR THERMAL PASTE ARE ALLOWED IN THE CHAMBER CAUTION: THE CHAMBER PLATE GETS EXTREMELY HOT Start Up Procedure 1) Open bottle and regulator for Helium,
More informationSTS ICP-RIE. Scott Munro (2-4826,
STS ICP-RIE LOCATION: Plasma Etch Area PRIMARY TRAINER: Scott Munro (2-4826, email@address.com) 1. OVERVIEW The STS ICP-RIE is available to users who require deep anisotropic silicon etching with near
More informationNanofabrication Facility: PECVD SOP Rev. 00, April 24
Author: Charlie Yao & Mario Beaudoin Email: charlieyao@gmail.com; Beaudoin@physics.ubc.ca Phone: 604-822-1853(MB). Purpose This document outlines the standard operation for the Trion Plasma Enhanced Chemical
More informationUsage Policies Notebook for STS DRIE System
Usage Policies Notebook for STS DRIE System Revision date September 2014 2 Emergency Plan for STS DRIE System Standard Operating Procedures for Emergencies Contact information Person Lab Manager Director
More informationStandard Operating Procedure. For. PVD E-Beam
P a g e 1 Standard Operating Procedure For PVD E-Beam P a g e 2 Introduction The PVD Electron-Beam Evaporator (E-Beam) thin film deposition machine uses a magnetically guided and collimated stream of electrons
More informationKARL SUSS MJB3 UV400 Mask Aligner Standard Operating Procedure
KARL SUSS MJB3 UV400 Mask Aligner Standard Operating Procedure Version: 1.0 February 2014 UNIVERSITY OF TEXAS AT ARLINGTON Nanotechnology Research Center (NRC) 1 TABLE OF CONTENTS 1 Introduction 3 1.1
More informationStandard Operating Manual
Standard Operating Manual Karl Suss MA6 Mask Aligner Version 1.1 Page 1 of 24 Contents 1. Picture and Location 2. Process Capabilities 2.1 Cleanliness Standard 2.2 Substrate Size 2.3 Photo Mask Size 2.4
More informationApproved by Principal Investigator Date: Approved by Super User: Date:
Approved by Principal Investigator Date: Approved by Super User: Date: Standard Operating Procedure BNC Commonwealth Dual Ion Beam Deposition System (CDIBS) Version 2010 February 14 I. Purpose This Standard
More informationTitle: Xactix XeF2 Etcher Semiconductor & Microsystems Fabrication Laboratory Revision: A Rev Date: 03/23/2016
Approved by: Process Engineer / / / / Equipment Engineer 1 SCOPE The purpose of this document is to detail the use of the Xactix XeF2 Etcher. All users are expected to have read and understood this document.
More informationCOBILT CA-800 Mask Aligner Equipment Operation
COBILT CA-800 Mask Aligner Equipment Operation For the Micro-Electronics Laboratory At University of Notre Dame Department of Electrical Engineering This user manual is not be removed from room 247A. This
More informationPlasma-Therm PECVD. Operating Characteristics. Operating Instructions. Typical Processes. I. Loading. II. Operating
Plasma-Therm PECVD A PECVD (plasma enhanced chemical vapor deposition) reacts gases in a RF (radio frequency) induced plasma to deposit materials such as silicon dioxide and silicon nitride. This PECVD
More informationKARL SUSS MJB3 MASK ALIGNER STANDARD OPERATING PROCEDURE
KARL SUSS MJB3 MASK ALIGNER STANDARD OPERATING PROCEDURE Purpose of this Instrument: This instrument is for patterning photosensitive polymers with UV light. Location: White Hall 410 Cleanroom Primary
More informationNORDSON MARCH PX-1000 PLASMA ASHER STANDARD OPERATING PROCEDURE Version: 1.0 July 2016
NORDSON MARCH PX-1000 PLASMA ASHER STANDARD OPERATING PROCEDURE Version: 1.0 July 2016 UNIVERSITY OF TEXAS AT ARLINGTON Nanotechnology Research Center TABLE OF CONTENTS 1. Introduction..3 1.1 Scope of
More informationCryo-Evaporator Operation
Cryo-Evaporator Operation Cara Ricci November 25, 2003 Thin Film Deposition THE UNIVERSITY OF TEXAS AT DALLAS ERIK JOHNSON SCHOOL OF ENGINEERING DOCUMENT NUMBER: FA2003-TF-008 EDITION: 1.1 PAGE: 1 of 28
More informationThermcraft Tube Furnace General Use
Page 1 of 9 Thermcraft Tube Furnace General Use The Thermcraft furnace is a general use, 3 zone tube furnace capable of reaching temperatures of 1200 C. The large 6 diameter quartz tube is capable of holding
More informationThe SPI Sputter Coater Handbook
The SPI Sputter Coater Handbook Coating of Specimens SPI-Module Sputter Coater with Etch Mode 1. Mount the specimens onto the SEM stub. Keep in mind that many adhesives have high vapor pressure solvents
More informationLeaks, contamination and closed loop control how RGAs make coating processes more profitable
Leaks, contamination and closed loop control how RGAs make coating processes more profitable Backup: What s an RGA Residual Gas Analyzer An instrument that is measuring the gas composition in a chamber
More informationOperating Procedures for the. SAMCO ICP RIE System
Operating Procedures for the SAMCO ICP RIE System General Overview: The purpose of the SAMCO Model 200iP Inductively Coupled Plasma Reactive Ion Etcher (ICP RIE) is to etch III-V compound semiconductors
More informationSavannah S100 ALD at SCIF, UC Merced Standard operating Procedure
This document covers the procedure that should be followed for normal operation of the Cambridge NanoTech: Savannah S100 (Atomic Layer Deposition ALD). This tool is design to be used with whole 4inch wafers.
More informationArizona State University Center for Solid State Electronics Research Issue: E Title: Heat Pulse 610 Operating Procedure Page 1 of 7
Title: Heat Pulse 610 Operating Procedure Page 1 of 7 Table of Contents 1.0 Purpose/Scope... 2 2.0 Reference Documents... 2 2.1 Heat Pulse Operations Manual... 2 2.2 Solaris software Operations Manual...
More informationStandard Operating Manual
NANOELECTRONICS FABRICATION FACILITY (NFF), HKUST Standard Operating Manual STS ICP-DRIE Copyright 2014 by Hong Kong University of Science & Technology. All rights reserved. Page 1 NANOELECTRONICS FABRICATION
More informationTHERMAL EVAPORATION UNIT (for Al evaporation)
THERMAL EVAPORATION UNIT (for Al evaporation) System Owner: NeerajPanwar 9619507210 panwar.iitr@gmail.com System Operator: 1. Bhimraj Sable 9930189878 bhimrajsable71@gmail.com Authorized User: 1. Ramesh
More informationMarch CS-1701F Reactive Ion Etcher
March CS-1701F Reactive Ion Etcher Standard Operating Procedure Faculty Supervisor: Prof. Robert White, Mechanical Engineering (x72210) Safety Office: Peter Nowak x73246 (Just dial this directly on any
More informationUsage Policies Notebook for Karl Suss MA6 Mid / Deep UV Mask Aligner
Usage Policies Notebook for Karl Suss MA6 Mid / Deep UV Mask Aligner Revision date September 2014 2 Emergency Plan for Karl Suss MA6 Aligner Standard Operating Procedures for Emergencies Contact information
More informationOPERATION OF THE DIMPLER
OPERATION OF THE DIMPLER After thinning your sample to ~80 μm you can now do a dimpling process to thin the center up to 10 μm. When you walk in and use the DIMPLER it should already be calibrated and
More informationUniversity of Minnesota, MN Nano Center Standard Operating Procedure
Equipment Name: HDPCVD Revision Number: 2 Badger Name: HDPCVD Revisionist: L. von Dissen Model: Advanced Vacuum Date: 10/25/2016 Apex SLR ICP Location: PAN, Bay 3 1 Description The Apex SLR ICP is a high
More informationNanofabrication Facility: Sputter Evaporator SOP Rev. 04, June 2007
Author: Rev. 00: David Webster, TRIUMF, February 22, 1995. Rev. 01: A. Schmalz, October 12, 1999 Rev. 02: Doug Wong, August 2, 2002 (STS File: S02-014) Rev. 03: Mario Beaudoin, April 2006 Rev. 04: Bahador
More informationLESKER #1 STANDARD OPERATION PROCEDURE
Arizona State University NanoFab LESKER #1 STANDARD OPERATION PROCEDURE Rev D Table of Contents Contents Table of Contents...1 1. Purpose / Scope...2 2. Reference Documents...2 3. Equipment / Supplies
More informationThe MRL Furnaces USED FOR THIS MANUAL COVERS
The MRL Furnaces USED FOR 1. Making Silicon Oxide films from 10nm to 2um thickness 2. Annealing with temperatures from 30 800C and times from 5min to 2days 3. Diffusion with temperatures from 30 1100C
More informationNRF Suss Delta 80 Spinner SOP Revision /14/2016 Page 1 of 11. Suss Delta 80 Spinner SOP
Page 1 of 11 Note: latest updates are blue. Table of Contents Suss Delta 80 Spinner SOP 1.0 Safety 2.0 Quality Controls and Calibration 3.0 Equipment Uses and Restrictions 4.0 Equipment Specifications
More informationTemescal BJD-1800 E-Beam Evaporator 1 System Overview - Cryo-pumped for typical base pressures in the low 10e-7 Torr range. - Four pockets in the
Temescal BJD-1800 E-Beam Evaporator 1 System Overview - Cryo-pumped for typical base pressures in the low 10e-7 Torr range. - Four pockets in the rotating hearth of the electron gun which allows deposition
More information1)! DO NOT PROCEED BEYOND THIS MARK
Operating Instructions for X-ray Photoelectron Spectrometer: Physical Electronics Model 555 XPS/AES (John H. Thomas, III, Ph.D., Electron Spectroscopy) Sample Insertion: figure 1. Sample insertion rod
More informationOLED vacuum deposition cluster system Sunicel Plus 400 / Plus 400L (Sunic Systems)
OLED vacuum deposition cluster system Sunicel Plus 400 / Plus 400L (Sunic Systems) Gen2 substrate size : 370 (+/- 0.2) mm x 470 (+/- 0.2) mm. Thickness : 0.55 to 2.0mm. Supports the following deposition
More informationCambridge NanoTech: Savannah S100. Table of Contents
Table of Contents 1.0 Purpose/Scope... 2 2.0 Reference Documents... 2 3.0 Equipment/Supplies/Material... 2 4.0 Safety... 2 5.0 Logbook... 3 6.0 Login and Launch Software... 3 7.0 Session Setup... 3 8.0
More informationWATER CONTROL SYSTEM QUICK START
SETTINGS MENU SYSTEM OPTIONS WATER LEVEL BAR GRAPH 3 DS SPRAY ON/OFF CS SPRAY ON/OFF BEACON WATER CONTROL SYSTEM QUICK START WWW.GFWORLDWIDE.COM +1 (208) 664-9291 SERVICE@GFWORLDWIDE.COM DISPLAY SCREEN
More informationPlasma II (AXIC) Standard Operating Procedure. Revision: 1.0 Last Updated: Feb.6/2013, Revised by Grace Li
Plasma II (AXIC) Standard Operating Procedure Revision: 1.0 Last Updated: Feb.6/2013, Revised by Grace Li Overview This document will provide a detailed operation procedure of the Axic Multimode LF-6 plasma
More informationREPRODUCIBILITY IN OPTICAL THIN FILM PROCESSING PART 1, THE VACUUM AND PUMPING
ABSTRACT REPRODUCIBILITY IN OPTICAL THIN FILM PROCESSING PART 1, THE VACUUM AND PUMPING Ronald R. Willey Willey Optical, Consultants, 13039 Cedar Street, Charlevoix, MI 49720, USA Ph 231-237-9392, ron@willeyoptical.com
More informationXactix XeF2 OPERATION MANUAL
General Information The Xactix e-1 is a xenon difluoride (XeF 2) isotropic silicon etcher. XeF 2 is a vapor phase etch, which exhibits very high selectivity of silicon to photo-resist, silicon dioxide,
More informationChapter 2 General description of the system
Chapter 2 General description of the system This system is a high density plasma etching system having a C to C load-lock system and an ISM (Inductive Super Magnetron) plasma source. The system consists
More informationPlasma Cleaner. Yamato Scientific America. Contents. Innovating Science for Over 125 Years. Gas Plasma Dry Cleaner PDC200/210/510 PDC610G.
Yamato Scientific America Innovating Science for Over 125 Years Plasma Cleaner Contents Gas Plasma Dry Cleaner PDC200/210/510 PDC610G Gas Plasma Reactor 145 146 147 149 144 Gas Plasma Dry Cleaner Plasma
More informationMarch Asher Operation
March Asher Operation Roger Robbins 7/31/2006 The University of Texas at Dallas Erik Jonsson Engineering School of Engineering TITLE: March Asher Operation Page 1 of 13 March Asher Operation Roger Robbins
More informationRAM 4021-DPX Operation Manual
RAM 4021-DPX Operation Manual Worldwide Manufacturer of Gas Detection Solutions TABLE OF CONTENTS ABL 4021-DPX / RAM 4021-DPX For Your Safety... 3 Description... 3 Setup Mode... 4 Lights/Alarms... 4 Operation...
More informationQuickstart Installation Checklist (Please refer to operation manual for complete installation instructions)
Quickstart Installation Checklist (Please refer to operation manual for complete installation instructions) 1. Uncrate blender from packaging. 2. Lift the blender and position over machine throat or floor
More informationPRad Target. Chris Keith JLab Target Group
PRad Target Chris Keith JLab Target Group Target Overview & Components Target Software Hazard Analysis and Mitigation Target Status, Performance& Remaining Work Installation Schedule Nov. 12, 2015 PRad
More informationBEST KNOWN METHODS. Transpector XPR3 Gas Analysis System. 1 of 6 DESCRIPTION XPR3 APPLICATIONS PHYSICAL INSTALLATION
BEST KNOWN METHODS Transpector XPR3 Gas Analysis System DESCRIPTION The Transpector XPR3 is a third-generation, quadrupole-based residual gas analyzer that operates at PVD process pressures and is the
More informationXactix Xenon Difluoride Etcher
Xactix Xenon Difluoride Etcher 1 Introduction This tool is a Xactix e1 series XeF2 (Xenon Difluoride) based vapor phase etch system for isotropic and selective silicon etching. The XeF2 reaction with silicon
More informationRAM Operation Manual. Worldwide Manufacturer of Gas Detection Solutions
RAM 4021 Operation Manual Worldwide Manufacturer of Gas Detection Solutions TABLE OF CONTENTS RAM 4021 For Your Safety... 2 Description.... 2 Setup Mode.... 2 Lights/Alarms.... 3 Operation.... 4 Calibration....
More informationUsage Policies Notebook for Thermco Atmospheric Diffusion Furnace system
Usage Policies Notebook for Thermco Atmospheric Diffusion Furnace system Revision date September 2014 2 Emergency Plan for Diffusion Furnaces Standard Operating Procedures for Emergencies Contact information
More informationLogin to ilab Kiosk. Revised 05/22/2018. Load your sample:
Login to ilab Kiosk Load your sample: 1. Check: The analysis chamber pressure is
More informationApproved by BNC Managing Director Paul Lum Date: Approved by PI (s) /Super User (s): _Peter Hosemann/Andy Minor_Date:
Approved by BNC Managing Director Paul Lum Date: Approved by PI (s) /Super User (s): _Peter Hosemann/Andy Minor_Date: Standard Operating Procedure BNC FEI Quanta 3D FEG/FIB ESEM Version 2011 Aug 30 I.
More informationRAM 4021-PR. Operation Manual. Worldwide Manufacturer of Gas Detection Solutions
RAM 4021-PR Operation Manual Worldwide Manufacturer of Gas Detection Solutions TABLE OF CONTENTS RAM 4021-PR For Your Safety... 2 Description.... 2 Setup Mode.... 2 Lights/Alarms.... 3 Operation.... 4
More informationCLEANLINESS STANDARD NCPRE tool contamination classification
Tool Identifier NCPRE Phosphorous diffusion furnace Document version 1.0 24 th May 2013 Documented by Karthick Murukesan CONTENTS I. CLEANLINESS STANDARD 1 II. PERFOMANCE OF THE TOOL 1 III. WAFER PRE REQUISITE
More informationOperating Instructions
Operating Instructions Before operating the thin film evaporator, please be aware of all safety concerns associated with this experiment: Burn hazard from the column and steam lines, Chemical hazards associated
More informationRAM Operation Manual
RAM 4021-1 Operation Manual Worldwide Manufacturer of Gas Detection Solutions TABLE OF CONTENTS RAM 4021-1 For Your Safety... 2 Description... 2 Setup Mode... 3 Lights/Alarms... 3 Operation... 4 Calibration...
More informationAutomatic LN2 Fill Station Instructions
Automatic LN2 Fill Station Instructions Roger Robbins 6/7/2010 Introduction: This is a step by step pictorial instruction document on how to fill a portable Liquid Nitrogen (LN2) Dewar from the Automatic
More informationOXY Integral. INTERCON ENTERPRISES INC Tel: Fax: Internet:
OXY Integral INTERCON ENTERPRISES INC Tel: 800 665 6655 Fax: 604 946 5340 E-Mail: sales@intercononline.com Internet: www.intercononline.com Manual Integral 2006 1 INDEX 2-3 PREFACE 4 INTRODUCTION 5 Principle
More information