Multicam Oxy-Fuel, Plasma Operations Guide Series 2/05
|
|
- Darrell Poole
- 6 years ago
- Views:
Transcription
1 2/05
2 TABLE OF CONTENTS HANDHELD PENDANT (KEYPAD) OVERVIEW 2 GENERAL OPERATION Finding HOME 3 Machine Parking 3 LOADING MATERIAL 4 Setting HOME 4 Plate Rotation 5 Speed Control 5 MACHINE TOOL SETUP General 6 Torch Selector Switch 6 Material Library 6,7 PLASMA OPERATION 8 PC Comm (PC communications-program Loading) 8 Program Execution 8,9 Dry Run 9 Step and Repeat 9 Params 2D (Cutting Parameter Adjustment) 10,11 OXY-FUEL OPERATION 12 Gas/Pressure Settings 12 Setting Surface 13 Oxy-Fuel Preheat controls 13,14 Torch Ignition/Hi-Preheat 15 Oxy-Fuel Gas Manifold 16 Cutting Oxygen 16 Final Setup / Program Selection 17 Program Execution / Height Adjust 18 APPENDICES X Axis Wheel Lubrication OXY-FUEL Cutting Charts 19,20 1
3 HANDHELD PENDANT (KEYPAD) OVERVIEW 2
4 1. Inspect machine for debris and obstructions to travel 2. Power up 6000 controller 3. Finding HOME - at each Boot (initialization) the machine must be referenced (find its limits (0,0) Press Shift + Find Home to reference machine Machine will find its home in the Z axis, then the Y and X axes Machine Parking For easier plate loading, you may park the machine at the far end by pressing SHIFT + 8 NOTE: SHIFT + 2, 4, 6, or 8 will park the machine in that direction. PARK means to travel at slew (max) speed to the limit of travel 3
5 4. LOADING MATERIAL Load material to be cut onto the table. Plate location is not as important as its squareness. When loading large plate or heavy materials, it may not be possible to square the sheet sufficiently. The PLATE ROTATION feature may be used to rotate the program to match sheet orientation See Pg SETTING HOME JOG the machine to the lower right hand corner of the plate to be cut. PRESS SET HOME, then ENTER 4
6 PLATE ROTATION (rotate part to fit sheet) SET HOME at the lower right hand corner of the material, then JOG to the upper right hand corner. PRESS SET HOME again, then PRESS the DOWN (2 KEY). When you press EXECUTE, to run your program, you will be prompted to accept or cancel the degrees of rotation. Speed Control Bring the torch down to the plate. For more accurate control of torch movement, once you are close to the plate, Press the OCP speed control, to SLOW Each Press of the Speed Control Key toggles from Med, to Fast, to Slow And bring torch tip as close as is safe without jamming the torch into the material (within a 1/16 ) 5
7 6. MACHINE TOOL SETUP a. Turn ON the Plasma unit and gases or turn ON Oxy-fuel gases. Be sure you have the gases required for the material to be cut turned on. All others should be turned off. While turning gases off is not required, gas loss by seepage will be minimized. NOTE: Always be sure to open or close valves completely. ALL plasma gas outlet pressures MUST be set to 120 psi (flowing) See manual plasma manual for gas test procedure b. On the keypad PRESS the MATERIAL LIBRARY button 6. MACHINE TOOL SETUP Cont. c. You will be prompted for MATERIAL TYPE. Use the 8 and 2 keys to scroll up and down to the proper type (Mild Steel, Stainless Steel, Aluminum, or Oxy Fuel), then PRESS ENTER. 6
8 d. Next you are prompted for SHIELD or UNSHIELDED, select SHIELDED (Only PowerMax units use unshielded consumables) e. You will be then prompted for AMPERAGE (plasma) or TIP SIZE (Oxy-Fuel) Use the 8 and 2 keys to INCREASE or DECREASE f. Use the 4 and 6 keys to move left and right between AMPERAGE/TIP SIZE and MATERIAL THICKNESS. Use the 8 and 2 keys to select the proper thickness, then Press ENTER NOTE: When changing plasma consumables DO NOT pull Ohmic Sensor by wire. Grasp the connector to remove. 7. PLASMA OPERATION Inspect machine for debris and obstructions to travel Be sure you have the correct consumables for the amperage and material thickness desired. Use only plasma manufacturer s parts. 7
9 8. Press PC COMM, use the up/down arrow keys to select the program you wish to cut, then Press ENTER 11. Press EXECUTE. The program will be checked as a valid program. Any out of bounds error means that the program cannot be started at its present Home position, as it will run out of space in the given direction, prior to completing the cut. 12. Press Execute a 2 nd time to begin cut. or DRY RUN (machine follows the toolpath at max speed without firing the torch) Dry run can be used to check a part, check sizing, etc. 8
10 Once the program has been validated, Pressing the 2 key will allow you to Dry Run Or STEP and REPEAT (Onboard rectangular nesting) Pressing the 2 key again, allows you to select how many times the part is to be cut. 13. Program Completion Depending on the software you are using at the end of cut, you will be asked to Press START to Continue, which returns you to the SET HOME POSITION or cuts off the scrap material. Otherwise when the program is complete it simply returns to the MAIN MENU Congratulations! You have cut your first part. CHANGING CONSUMABLES Most plasma systems over 100 amps are water cooled. This means that as long as the plasma unit is powered on, there is coolant flowing through the torch. The plasma unit must be shutdown to change consumables. Autogas units (HPR) have their power applied by the controller. To power down the plasma unit you go to MENU, UTILITY, then CHANGE TIP. You must press ENTER twice to turn the unit off. PARAMS 2D Select MENU, then PARAMS 2D Check PARAMS 2D to verify the proper settings for the material to be cut, 9
11 In PARAMS 2D, use the Arrow keys to navigate through the selections. NOTE: Z UP, and Z DOWN, can be used to Page Up and DOWN through the selections 10
12 There have been some additions to the standard Params 2D MENUS ARC FACTOR Arc Factor sets the percentage of the feedrate at which arcs will be cut. The range is 0 1. An arc factor of.4 means that if the material feedrate is set to 100 ipm, then arcs will be cut at 40 ipm. Adjustable arc feedrate can help maintain arc s cylindrical quality NOTE: In conjunction with ARC FACTOR parameters affect arc cutting. See your tech rep for more information 11
13 PERF This is a YES/NO toggle. Perf refers to perforated metal. Metal with holes or gaps cause a loss of ground, which would normally halt the cutting process. Selecting YES will allow the cutting process to continue by not monitoring arc loss. NOTE: Once a change to the material setup has been verified over a number of cuts, you can UPDATE MATERIAL LIBRARY, and your settings will be saved. 12
14 7. OXY FUEL SETUP a. Turn on Oxygen and Acetylene gases Set Gas regulator pressure to appropriate settings for the tip / material to be cut. For more info on setups see appendix, and refer to your Welding/Cutting guides b. Setting Oxy-Fuel Torch Surface Jog the Z axis down until your torch tip touches the plate (within 1/16 ) Press SET SURFACE. Select torch 2 (2 may already be displayed, Press 2, to be sure, ENTER 13
15 Be sure Low Preheat Controls and Torch adjustment knobs are set to OFF, LOW PREHEAT CONTROL c. Set Home Oxy Fuel Set the plate/part home. Normally the right lower corner in reference to the OCP (Operator Control Pendant) To SET HOME jog the machine to the desired HOME position, and Press HOME, then ENTER 14
16 15
17 c. TORCH IGNITION Jog machine to a convenient location for torch ignition. Open torch preheat adjustment knobs slightly. Turn ON Lo-Preheat Fuel, ignite gas with striker Turn ON Lo-Preheat Oxygen Torch Settings Adjust Low / Ignition gases until a flame approx 8-10 long is achieved, with 3 well defined cones near the tip ~ long Preheat Height and Cut Height should be approximately the same. Cones should just touch the material. Pierce height should be somewhat higher to avoid fouling the tip. d. HI-PREHEAT Press SHIFT + 9 to access the gas setting menu. Select Hi-Preheat, and observe the flame for proper preheat flame (see torch/welder s manual) Select Hi-Preheat Adjust gas pressure according to the cutting chart. Flame will shorten, and become more intense cones should remain well defined. 16
18 Proper gas regulator settings may also be verified by pressing the Manual Solenoid Actuators, and adjusting gauges visually. The Cutting Oxygen has a metering valve to increase or decrease the cutting Oxygen flow. e. CUTTING OXYGEN Select CUT OXYGEN, using the CUT OXYGEN REGULATOR (center reg), adjust flame for an ENVELOPE 4-5 long (see welder s manual for pressure) 17
19 f. FINAL SETUP Select LOW PREHEAT then LAST HOME (Shift then SET HOME) to return to PLATE HOME position g. Select your Program, using the PC Comm, button 18
20 h. Pressing EXECUTE will prompt you to light the flame. Pressing EXECUTE a 2 nd time will move the torch to the PIERCE POINT, and lower the torch to the PREHEAT HEIGHT. The controller will automatically go into Hi-Preheat. Press the 2 key which allows a DRY RUN (actual cut motions, without the torch) of the cut. This can be helpful on thicker materials, in essence preheating the entire toolpath When you are satisfied that the material has been sufficiently preheated (puddling and some splatter will occur at pierce point) pressing EXECUTE the 3 rd time will begin the cutting sequence. The pierce sequence automatically turns on the CUTTING OXYGEN; the torch will raise slightly to PIERCE HEIGHT, and then waits a predetermined PIERCE DELAY TIME (See 2D Params) NOTE: THE Z HEIGHT MAY BE ADJUSTED (ON THE FLY) WHILE CUTTING At the end of cut the excess cutting oxygen will be dumped (see dump valve behind Cutting Oxygen regulator, returning the torch to Lo-Preheat settings. Raise the torch using Z UP. Turn the Oxygen and Fuel Lo-Preheat switches to OFF. A slight Pop may be heard when torch is extinguished. You are now ready to cut your next plate. Good Work! Congratulations once again. Welcome to the Multicam family of motion controls and products. 19
21 Appendices 1. X Axis Wheel Lubrication The X axis wheels and gear rack require oiling. The oil required is MOBIL Vactra #2 Due to the viscosity a lever-type Oil Gun is also required. This should be a Lever-Type Oil Gun Heavy Duty 26 oz. Capacity These items can be found in an MSC catalog (this catalog is given as reference only) 2. OXY-FUEL Cutting Charts 20
22 2. OXY-FUEL Cutting Charts Cont. 21
OPERATION. Estimated kerf width compensation. HPR260 Manual Gas Instruction Manual 4-9
Estimated kerf width compensation The widths in the chart below are for reference. Differences between installations and material composition may cause the specific user results to vary from those shown
More information4 Machine maintenance and repair
3.3 lift device consists of: lift motor, lead screw, guide rod, lifting seat Lift motor Lead screw Guide rod Lifting seat Diagram 3.3 3.4 torch holder set The torch holder consist of holder connection,
More informationPowermax machine-side reference guide For mechanized applications with Powermax1000, Powermax1250 and Powermax1650
Powermax machine-side reference guide For mechanized applications with Powermax1000, Powermax1250 and Powermax1650 This Powermax machine-side reference guide is a supplement to your Operator Manual and
More informationMild steel. Stainless steel. HPR130XD Auto Gas Revision 2. Nozzle retaining cap. tube. Shield cap 30 A 50 A 80 A 130 A
Operation Mild steel cap Nozzle retaining cap Nozzle Swirl ring Electrode 220194 220754 220193 220180 220192 220555 220754 220554 220553 220552 Water tube 30 A 50 A 220340 220747 80 A 220189 220756 220188
More informationTIPS Oxyfuel advice from the Annual Ironworker Instructor Training Program
TIPS Oxyfuel advice from the Annual Ironworker Instructor Training Program by Travis Ham, senior product manager, gas equipment, ESAB, Victor Technologies During the week of July 18, a team of ESAB experts
More informationOXY FUEL SYSTEM SET UP & SHUT DOWN PROCEDURE CHECKLIST ACETYLENE FUEL GAS
OXY FUEL SYSTEM SET UP & SHUT DOWN PROCEDURE CHECKLIST ACETYLENE FUEL GAS Items needed for demonstrations: Fire extinguisher PPE (Personal Protective Equipment): o Lab coats/welding jackets o Leather gloves
More informationHyDefinition HD3070. Automatic Gas Console Upgrade. Field Service Bulletin (P/N ) Revision 2 April, 2002
HyDefinition HD3070 Automatic Gas Console Upgrade Field Service Bulletin (P/N 803100) Revision April, 00 Hypertherm, Inc. Hanover, NH USA www.hypertherm.com Copyright 00 Hypertherm, Inc. All Rights Reserved
More informationTouch Screen Guide. OG-1500 and OG Part # T011
Touch Screen Guide OG-1500 and OG-2000 Part # 9000000.T011 Effective 11/2010 External View Internal View 1. Transducer Banks 2. Oxygen Sensor 3. PLC These are the two manifolds with three (3) transducers
More informationWhat is Oxy-Fuel Welding?
Oxy-Fuel Welding What is Oxy-Fuel Welding? Process the fuses metal together Does not require electricity Uses a torch and filler rod Similar equipment as Oxy-Fuel Cutting Where is Oxy-Fuel Welding used?
More informationSection 4. In this section: HPR400XD Auto Gas
Section 4 Operation In this section: Daily start-up...4-3 Check torch...4-3 Power indicators...4-4 General...4-4 Power supply...4-4 ion console...4-4 Metering console...4-4 CNC controller requirements...4-5
More informationSafe Work Instructions For Oxygen Acetylene Equipment
Safe Work Instructions For Oxygen Acetylene Equipment Policy Sponsor: Assistant Vice President Facilities Management Responsible Unit: Trade Services Approval Date: September 2010 Revisions: January 2018
More informationTrue Hole technology frequently asked questions
True Hole technology frequently asked questions What is True Hole technology? Hypertherm s patent pending True Hole cutting technology produces significantly better hole quality than what has been previously
More informationOxy-Fuel Safety Training. Participant s Guide
Oxy-Fuel Safety Training Page 1 of 19 Contents What s Included?... 3 Oxy-Fuel Safety Training Objectives... 4 Chapter 1: Safety & Responsibility... 6 Chapter 2: Gases in the Work Area... 7 Chapter 3: Equipment
More informationVisit our Web site: http: //
CONTENTS: Medium Duty Victor Style Welding And Cutting Outfit MANUFACTURED BY AN ISO 9001 REGISTERED FIRM Visit our Web site: http: // www.northerntool.com TABLE OF CONTENTS Page INTRODUCTION... 1 SECTION
More informationSAFETY AND OPERATION MANUAL
SAFETY AND OPERATION MANUAL Congratulations on purchasing the GASPONY 1 Portable Welding/Cutting Outfit! This manual is designed to help you get the most out of your GASPONY 1. CAREFULLY REVIEW ALL SAFETY
More informationHyDefinition HD4070. Plasma Arc Cutting / Marking System. Product Configuration Manual Revision
HyDefinition HD4070 Plasma Arc Cutting / Marking System Product Configuration Manual 803770 Revision 1 4070.97 HD4070 Product Configuration Manual (P/N 803770) Revision 1 December, 2002 Hypertherm, Inc.
More informationTactical Advance Series Tactical Advance HD Series. Simplifying CNC Plasma Cutting.
Tactical Advance Series Tactical Advance HD Series www.tacticalcnc.com Technology at work for you What makes the Tactical CNC Advantage and Advantage HD Series the best automated plasma cutting solution
More informationJETFIRST 150 RTA SYSTEM OPERATING MANUAL Version: 2 Feb 2012
JETFIRST 150 RTA SYSTEM OPERATING MANUAL Version: 2 Feb 2012 UNIVERSITY OF TEXAS AT ARLINGTON Nanofabrication Research and Teaching Facility TABLE OF CONTENTS 1. Introduction....2 1.1 Scope of Work.....2
More informationTRADE OF HEAVY VEHICLE MECHANIC
TRADE OF HEAVY VEHICLE MECHANIC PHASE 2 Module 1 Induction/Customer Care/Bench Fitting/Welding UNIT: 5 Table of Contents Aims and Objectives... 1 Learning Outcome:... 1 Setting up an Oxyacetylene torch...
More informationV-24 OXYGEN LANCE VALVE
INSTRUCTIONS for F-4737-U May, 2009 V-24 OXYGEN LANCE VALVE w/ C -Size Inlet w/ B -Size Inlet V-24 Oxygen Lance with 1/8" Pipe Holder... 9728D65... 2218939 V-24 Oxygen Lance with 1/4" Pipe Holder... 9728A65...
More informationOXYGEN ACETYLENE WELDING & CUTTING EQUIPMENT
OXYGEN ACETYLENE WELDING & CUTTING EQUIPMENT Introduction: The oxy-acetylene torch can be used for various tasks. It can be used for cutting steel, welding steel, brazing and for heating metal. The oxy-acetylene
More informationDeveloped by Ricky Summer November 11, 2015
P E T R O G E N T O R C H O P E R A T I O N S 1.1 Developed by Ricky Summer November 11, 2015 T A S K S K I L L D E S C R I P T I O N A N D D E T A I L This heading includes information about the following:
More informationOperator s Manual Heavy Duty Torch Kit VTK-HD-B
Operator s Manual Heavy Duty Torch Kit VTK-HD-B WARNING: Do not assemble, install or operate this equipment without reading ALL of this manual and the safety precautions and warnings illustrated in this
More informationCUTTING TORCH SAFETY. The Safe Use and Handling of OXY Fuel Cutting, Welding, and Heating Equipment
CUTTING TORCH SAFETY The Safe Use and Handling of OXY Fuel Cutting, Welding, and Heating Equipment Introduction Safe operation for the use of gas cutting, heating and welding requires a clear understanding
More informationTime-Delay Electropneumatic Applications
Exercise 3-4 EXERCISE OBJECTIVE & & & To introduce time delays; To describe the operation of a time-delay valve; To describe the operation of a time-delay relay. DISCUSSION Time-Delays Time delays are
More informationPRESSURE CONTROL REGULATORS
REGULATOR HARRIS STYLE SINGLE STAGE 201 Series Medium Duty Single stage construction Forged brass body for maximum strength Chrome bonnet Neoprene diaphragms Sintered metal inlet filter to trap impurities
More informationHPICAL Operation & Data Logging Procedures. Click spacebar to advance through slides 1
HPICAL-15000 Operation & Data Logging Procedures Click spacebar to advance through slides 1 WARNING Always wear proper safety equipment when using high pressure equipment. Do not exceed 125 psi air pressure.
More informationTechnical Operating Instructions for Magnum Cutting Systems. for online instructions
Technical Operating Instructions for Magnum Cutting Systems http://www.magnumusa.com/operating-video.html for online instructions In Case of Emergency Immediately Call for Medical Aid. Familiarize yourself
More informationFoundations of Agriculture
Foundations of Agriculture Auto body and Restoration Repairs on small parts Portable welding OAW was the first type of portable welder Acetylene is mixed with oxygen in correct proportions and ignited.
More informationASSEMBLY & OPERATIONS MANUAL. Straight & Clean Torch Cuts. Every Time.
ASSEMBLY & OPERATIONS MANUAL Straight & Clean Torch Cuts. Every Time. CAUTION ALWAYS USE FLASH BACK ARRESTORS (purchased separately) READ THIS BOOK THOROUGHLY AND FOLLOW INSTRUCTIONS! FAILURE TO USE OSHA
More informationPegas 4000 MF Gas Mixer InstructionManual Columbus Instruments
Pegas 4000 MF Gas Mixer InstructionManual Contents I Table of Contents Foreword Part I Introduction 1 2 1 System overview... 2 2 Specifications... 3 Part II Installation 4 1 Rear panel connections...
More informationSEMME269 - SQA Unit Code H2BK 04 Cutting and shaping using NC/CNC plasma or gas cutting machines
Cutting and shaping using NC/CNC plasma or gas cutting machines Overview This unit identifies the competences you need to carry out cutting and shaping operations using numerical control (NC) or computer
More informationHPRXD Technology Advancements
HPRXD Technology Advancements Thin stainless steel with HDi technology Thick stainless steel piercing technique Fine Feature cutting Underwater cut charts 200 A mild steel bevel cut process Manual Addendum
More informationChiyoda's High-Pressure Gas Control System and Equipment
Chiyoda's High-Pressure Gas Control System and Equipment 2012 CHIYODA HELPS YOUR GAS RELATED JOBS... Since the establishment 1946, we started as a manufacturer of Gas Welding & Cutting Equipment. Nowadays
More information10.1 Main Unit. INDEPENDENT WHOLESALE WELDING SUPPLY Ph: Fax: Website:
10.1 Main Unit 10.1 Main Unit 1 Case 60031802 1 2 Cross feed holder 60031803 1 3 Cross feed liner 60031804 1 4 Handle 60031805 1 5 Fan cover 60031806 1 6 Bottom plate 60031807 1 7 Heat shield 60031808
More informationDescription. Lesson Outcomes. Assumptions. Terminology. Welding. Automotive
Description Oxyacetylene or fusion welding is one of the oldest methods of joining metal. Oxyacetylene welding equipment is very common in an automotive shop and has many uses. It is most often used to
More informationEXOTHERMIC TORCH ADAPTER. Instruction Manual
EXOTHERMIC TORCH ADAPTER Instruction Manual CAUTION FLAME TECH ALWAYS RECOMMENDS USING FLASH BACK ARRESTORS (must purchase separately) Pre-operation Checklist Before you begin, the following routine checks
More informationRisk Management Resources
Risk Management Resources Machine Guarding Name: Notes: Electrical Systems: Fire Prevention Are circuit breakers accessible to personnel, protected from physical damage, and located away from ignitable
More informationO P E R ATING INSTRUCTIONS FOR MODEL SPR-45 Automatic Screen and Stencil Printer
O P E R ATING INSTRUCTIONS FOR MODEL SPR-45 Automatic Screen and Stencil Printer TABLE OF CONTENTS I. SPECIFICATIONS...3. II. SAFETY INSTRUCTIONS...4. III. INSTALLATION...5. IV. SET-UP...6. V. SYSTEM OPERATION...9.
More informationApollo Safety Features
Overview of Emergency Start Mains Power Failure Gas Supply Failure Ventilator Failure Fresh Gas Delivery Failure Ventilator and Fresh Gas Delivery Failure Display Failure User Interface Failure System
More informationLCR-6-WT-EPP CYLINDER ROLLER EXPLOSION PROOF SERIES INSTRUCTION MANUAL MANUAL NUMBER Rev A Issued November 2011
LCR-6-WT-EPP CYLINDER ROLLER EXPLOSION PROOF SERIES INSTRUCTION MANUAL MANUAL NUMBER 21-11-1065 Rev A Issued November 2011 Copyright 2011, Galiso, Inc. 22 Ponderosa Ct., Montrose, CO 81401 (970) 249-0233
More informationMisaligned Folds Paper Feed Problems Double Feeds Won t Feed FLYER Won t Run iii
Operator s Manual Table of Contents Operator Safety... 1 Introduction... 2 Unpacking and Setup... 3 Unpacking... 3 Setup... 4 FLYER Overview... 5 FLYER Diagram... 5 Capabilities... 5 Control Panel... 6
More informationMASTEEL FABRICATION EQUIPMENT
MASTEEL FABRICATION EQUIPMENT MBHS SERIES HYDRAULIC SYNCHRONIZED CNC BRAKES STANDARD CONTROL FEATURES Standard KV-2004 CNC control with 11 TFT screen display 0.0004 high resolution linear scales provide
More informationThis training does not attempt to cover all safety regulations or precautions.
This training does not attempt to cover all safety regulations or precautions. For additional safety regulations and precautions, see the following standards: American Welding Society (AWS) American National
More informationINSTRUCTION MANUAL For Gas Welding, Cutting, Brazing & Heating Torches.
THE HARRIS PRODUCTS GROUP INSTRUCTION MANUAL For Gas Welding, Cutting, Brazing & Heating Torches. IMPORTANT: For your own safety read these instructions. Failure to do so can lead to serious injury. www.harrisproductsgroup.com.au
More informationU.S. CONCRETE, INC. SAFETY POLICY and PROCEDURE MANUAL
SAFE -14 Page 1 of 8 U.S. CONCRETE, INC. SAFETY POLICY and PROCEDURE MANUAL FUNCTION Safety TOPIC Hotwork Permit Program OBJECTIVE(S): GENERAL POLICY: To provide a work atmosphere that is conducive to
More informationInstallation Instructions
Model: ACT-4100 ACT-4100-3 ACT-4100-6 SUN ELECTRIC CORPORATION Page: 1 of 5 Installation Instructions INSTALLATION MUST BE PERFORMED BY QUALIFIED SUN PERSONNEL ONLY INSTALLATION OVERVIEW: The Installation
More informationInstallation Instructions
Model: ACT-4500 ACT-4500-3 ACT-4500-6 SUN ELECTRIC CORPORATION Page: 1 of 5 Installation Instructions INSTALLATION MUST BE PERFORMED BY QUALIFIED SUN PERSONNEL ONLY INSTALLATION OVERVIEW: The Installation
More informationSafety, Set-Up, and Operating Instructions
Read all Instruction, SAVE THESE INSTRUCTION Safety, Set-Up, and Operating Instructions Gas Welding, Cutting, Brazing & Heating There are many hazards to be considered when using oxy-fuel welding, cutting,
More informationCal/OSHA T8 CCR 1536 Cal/OSHA T8 CCR 4799 Cal/OSHA T8 CCR 4845 Cal/OSHA T8 CCR 4848
Cal/OSHA Gas Systems for Welding GAS WELDING Cal/OSHA T8 CCR 1536 Cal/OSHA T8 CCR 4799 Cal/OSHA T8 CCR 4845 Cal/OSHA T8 CCR 4848 When performing gas welding, the following precautions, work procedures,
More informationUnderwater Welding & Cutting
Underwater Welding & Cutting By Leif Andersen, Underwater welding & cutting is generally divided into Dry and Wet underwater welding & cutting. Dry underwater welding & cutting is performed in a chamber
More informationQUORUM TECH 150RES THE FIRST AND THIRD WEEK WILL BE SET UP FOR CARBON COATING THE SECOND AND LAST WEEK WILL BE SET UP FOR GOLD COATING
QUORUM TECH 150RES This document is intended to describe the function and use of the QuorumTech Q150RES system. Formal training and qualification by staff is required before gaining access to the tool.
More informationTEST BENCH FOR SAFETY VALVES
TEST BENCH FOR SAFETY VALVES 1) Hydro panel : This Panel possesses This Bench Contains One Panel and One Reservoir. 1 No. Monobloc Version : Single Phase AC, 50 Hz Type of Duty :S1 (Continuous) Class of
More informationInstallation Instructions
Page 5750-S-1 Installation Instructions General These mounting instructions for Circular INCINO- PAK Burners are in addition to the specific instructions offered for other Maxon component items: Shut-Off
More informationFLAME CUTTING HANDBOOK
FLAME CUTTING HANDBOOK 2 BUG-O SYSTEMS BUG-O Systems Kits are assembled from modular components. Each kit was originally an adaptation to meet an actual problem. The concept is both practical and economical,
More informationExercise 2-3. Flow Rate and Velocity EXERCISE OBJECTIVE C C C
Exercise 2-3 EXERCISE OBJECTIVE C C C To describe the operation of a flow control valve; To establish the relationship between flow rate and velocity; To operate meter-in, meter-out, and bypass flow control
More informationUBEC 1AT. AUTO TANK Fill System Installation, Operation, & Setup Instructions
Document Number: XE-ATA5PM-R1A UBEC 1AT AUTO TANK Fill System 08899155 Installation, Operation, & Setup Instructions Rev170906-EB-FRC PHYSICAL: 1302 WEST BEARDSLEY AVE ELKHART, IN 46514 WWW.ELKHARTBRASS.COM
More informationSequence of Operations
MAGNUM Condensing Unit Software 5580 Enterprise Pkwy. Fort Myers, FL 33905 Office: 239-694-0089 Fax: 239-694-0031 Sequence of Operations MAGNUM Chiller V8 software www.mcscontrols.com MCS Total Solution
More informationTABLE OF CONTENTS SAFETY FIRST!...3 BASIC OPERATION...4 ADJUSTMENTS...5. Cocking Pressure...5. Three-Way Valve Adjustment...6
TABLE OF CONTENTS SAFETY FIRST!...3 BASIC OPERATION...4 ADJUSTMENTS...5 Cocking Pressure...5 Three-Way Valve Adjustment...6 External Three-Way adjustment...6 In-Line Regulator...6 Ram to Cocking Block
More informationWelding. Module
Welding Module 19.2.4 Module 19.2.4 Describe the oxy fuel gas welding process. Process: setting up the equipment, leak testing, oxy-fuel gas mixing, flame adjustment (including oxidizing, neutral and carburizing
More informationTANK MANAGER FOR TWO TANKS OPERATING MANUAL. 10/31/11 C-More T6C L color touch panel
TANK MANAGER FOR TWO TANKS OPERATING MANUAL 10/31/11 C-More T6C L color touch panel 1 TABLE OF CONTENTS GENERAL...3 INSTALLATION...4 STONE TEST PROCEDURE...7 OPERATIONAL SUMMARY...7 AUTO CARBONATION...10
More informationThe Crossvent 2i+ 2. Ventilator Concept (brief theory of operation and features)
The Crossvent 2i+ 1. How is this ventilator classified 2. Ventilator Concept (brief theory of operation and features) -Your Two Choices with this Ventilator 3. An overview of the device (an in-service)
More informationXactix XeF2 OPERATION MANUAL
General Information The Xactix e-1 is a xenon difluoride (XeF 2) isotropic silicon etcher. XeF 2 is a vapor phase etch, which exhibits very high selectivity of silicon to photo-resist, silicon dioxide,
More informationWire Buddy Manual IOpath Software
Wire Buddy Manual IOpath Software Wire Buddy is a calculation reference tool for Electricians and Maintenance personnel. Wire Buddy was created for the Maintenance Electrician. There are many occasions
More informationNO SMOKING WHEN OXYGEN IS IN USE.
OXYGEN SYSTEM DESCRIPTION NO SMOKING WHEN OXYGEN IS IN USE. Oxygen for flight crew and passengers is supplied by a 77 cu ft high pressure (1850 psi) cylinder, located in the right side of the nose compartment.
More informationXpressFill XF4500C Counter Pressure Can Filler. Operating Instructions
XpressFill XF4500C Counter Pressure Can Filler Operating Instructions ii XPRESSFILL Systems LLC lling machine. ank you for choosing our handcrafted bottle filler as the technology to bottle your passion.
More informationWilkins Safety Group
Gas Welding INTRODUCTION Welding is the union of pieces of metal by fusing the opposing surfaces that have been made molten by heat. Processes similar to welding include brazing and soldering. Allied processes
More informationWELDING, CUTTING AND BRAZING
- 1 - WELDING, CUTTING AND BRAZING Are only authorized and trained personnel permitted to use welding, cutting or brazing equipment? Does each operator have a copy of the appropriate operating instructions
More informationOperator: Save these instructions for future use!
INLET PRESS TAP WHITE-RODGERS 36E93-304 Delay-Opening Combination Gas Valve INSTALLATION INSTRUCTIONS Operator: Save these instructions for future use! FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY
More informationHT4400 Plasma Arc Cutting System Gas Panel
HT44 Plasma Arc Cutting System Gas Panel Instruction Manual 8421 - Revision 1 Integrated Plasma System For use with the NOTICE Use the HT44 instruction manual, 8358 as well as this manual, 8421, to install,
More informationOperating Instructions for Cobra and Lynx Duct Leakage Testers
Operating Instructions for Cobra and Lynx Duct Leakage Testers Table of Contents Introduction Introduction... 2 Safety Precautions Safety Precautions.. 2 Prior to Testing System Preparation.. 4 Power Requirements...
More informationoxyacetylene welding/cutting torch set
instructions for oxyacetylene welding/cutting torch set model no: SGA2.V2 & SGA6.V2 Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
More informationPROPORTIONING VALVE. Model 150 INSTRUCTION MANUAL. March 2017 IMS Company Stafford Road
PROPORTIONING VALVE Model 150 INSTRUCTION MANUAL March 2017 IMS Company 10373 Stafford Road Telephone: (440) 543-1615 Fax: (440) 543-1069 Email: sales@imscompany.com 1 Introduction IMS Company reserves
More informationPROPYLENE HEATING, BRAZING & WELDING
HEATING, BRAZING & WELDING Technical Data Sheets Heating Equipment HD HEATING HEADS *HD-1 *HD-2 *HD-3 *HD-4 *HD-5 435 105 63 27 Brazing Equipment Ph: 281-471-2200 Fx : 281-471-2201 18005 E Hwy 225 La Porte,
More informationProcess gas requirements (Core, VWI, and OptiMix gas connect consoles)
Process gas requirements (Core, VWI, and OptiMix gas connect consoles) You must supply the process gases and supply gas plumbing for your cutting system. See Table 7 on page 46 for supply gas quality,
More informationHow Flashback Arrestors Work
What are Flashback Arrestors Flashback Arrestors prevent reverse flow of gases with built-in check valves and extinguishes flashback fire with a stainless steel sintered element. How Flashback Arrestors
More information36E03 and 36E38 DSI and HSI Step Opening Combination Gas Valve INSTALLATION INSTRUCTIONS
INLET PRESS TAP WHITE-RODGERS 36E03 and 36E38 DSI and HSI Step Opening Combination Gas Valve INSTALLATION INSTRUCTIONS Operator: Save these instructions for future use! FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS
More informationBurner Management System DEMO Operating instructions
Burner Management System DEMO Operating instructions Burner Management System DEMO Operating Instructions Startup Summary - Normal startup is accomplished in four basic steps: 1. Leak Test a. Safety Valve
More informationFX134, FX1234, FX3030 Problem and Solutions
FX134, FX1234, FX3030 Problem and Solutions Unit Will Not Power Up Turn the power switch on. The unit LCD will display revision program and filter life within 3 to 5 seconds after turning on unit. If this
More informationXpressFill XF2500 Counter Pressure Filler. Operating Instructions
XpressFill XF2500 Counter Pressure Filler Operating Instructions ii XPRESSFILL Systems LLC lling machine. ank you for choosing our handcrafted bottle filler as the technology to bottle your passion. We
More informationWATER CONTROL SYSTEM QUICK START
SETTINGS MENU SYSTEM OPTIONS WATER LEVEL BAR GRAPH 3 DS SPRAY ON/OFF CS SPRAY ON/OFF BEACON WATER CONTROL SYSTEM QUICK START WWW.GFWORLDWIDE.COM +1 (208) 664-9291 SERVICE@GFWORLDWIDE.COM DISPLAY SCREEN
More informationTrion PECVD SOP IMPORTANT: NO PLASTIC, TAPE, RESISTS, OR THERMAL PASTE ARE ALLOWED IN THE CHAMBER
Trion PECVD SOP IMPORTANT: NO PLASTIC, TAPE, RESISTS, OR THERMAL PASTE ARE ALLOWED IN THE CHAMBER CAUTION: THE CHAMBER PLATE GETS EXTREMELY HOT Start Up Procedure 1) Open bottle and regulator for Helium,
More informationAIR DISTRIBUTOR. PART NUMBER (Including, but not inclusive) AD28483-_ALB, AD28563-_ALB, AD36097-_ALB, AD36098-_ALB, AD28485-_ALB
Manual #: MM-AD001 12/5/11 Rev. A Page 1 of 8 PART NUMBER (Including, but not inclusive) AD28483-_ALB, AD28563-_ALB, AD36097-_ALB, AD36098-_ALB, AD28485-_ALB Manual #: MM-AD001 12/5/11 Rev. A Page 2 of
More informationIntroduction to Pneumatics
Introduction to Pneumatics Pneumatics Symbols Air generation and distribution Table 1: Symbols use in energy conversion and preparation ITEM SYMBOL MEANING Compressor SUPPLY Pressure Source Pneumatic Pressure
More informationOPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS OXYGEN/ACETYLENE CUTTING AND WELDING KIT ! WARNING: There are a number of inherent hazards in the use of oxy-fuel welding and cutting apparatus. It is therefore necessary that proper
More informationInstallation Instructions
SUN ELECTRIC CORPORATION Model: MRC-450 MRC-450-3 MRC-450-6 MRC-450-GR Page: 1 of 5 Installation Instructions INSTALLATION MUST BE PERFORMED BY QUALIFIED SUN PERSONNEL ONLY INSTALLATION OVERVIEW: The Installation
More informationREACTOR 40 MECHANICAL Configuration Guide
REACTOR 40 MECHANICAL Configuration Guide Important Safety Information WARNING See the Important Safety and Product Information guide in the product box for product warnings and other important information.
More informationXpressFill XF4500 Counter Pressure Filler. Operating Instructions
XpressFill XF4500 Counter Pressure Filler Operating Instructions ii XPRESSFILL Systems LLC lling machine. ank you for choosing our handcrafted bottle filler as the technology to bottle your passion. We
More informationicreasepro Creaser Operators Manual
6-2013 Version 3.0 icreasepro Creaser Operators Manual WWW.MBMCORP.COM 800-223-2508 TABLE OF CONTENTS SPECIFICATIONS.1a SAFETY PROCEDURES/CARE & MAINTENANCE..1b COMPONENT IDENTIFICATION 2 TOUCH SCREEN
More informationELECTRONIC PLC SERIES Test Benches
Whether you are producing a single assembly or a production run, CustomCrimp has the test equipment to give both you and your customer the assurance that the product has been assembled correctly. A programmable
More informationSEMFWE3-33 SQA Unit Code HF2X 04 Cutting and shaping materials using portable thermal cutting equipment
Cutting and shaping materials using portable thermal cutting equipment Overview This standard identifies the competencies you need for cutting and shaping plate (3mm thickness and above), rolled sections,
More informationATL R/V Atlantis AUXILIARY PLANT OPERATION APPENDIX OPERATING PROCEDURES
110 AIR CONDITIONING CHILLED WATER PLANT 1. Ensure power to water chiller controller and all fan coil unit controllers is on 2. Ensure chilled water expansion tank level is at its proper level 3. Ensure
More informationLX Compass module 3 Electronic compass device User manual
LX Compass module 3 Electronic compass device User manual LX navigation d.o.o., Tkalska 10 SLO 3000 Celje, tel: + 386 3 490 46 70, fax: + 386 3 490 46 71 info@lxnavigation.si, http://www.lxnavigation.com
More informationALGE Water Polo Scoreboard
ALGE Water Polo Scoreboard USER MANUAL Split Second Timing Pty Limited PO Box 1322 Dee Why, NSW 2099 Tel: (02) 9981 6069 Fax: (02) 9981 6070 Email: info@splitsecond.com.au Web: www.splitsecond.com.au Page
More informationHercules Space Saver Sole Press series
Hercules Space Saver Sole Press series HERCULESSSD Also available in single, SKU: HERCULESSS Operator Manual Manufactured by: 2 HERCULES SPACE SAVER PRESS GENERAL DESCRIPTION Your Hercules Press is designed
More informationSection 3000 CONVEYOR CHAIN LUBRICATION SCHEMATIC...39 AIR OPERATED SPRAY DISPENSERS - CENTRAL ACRYLIC RESERVOIR Section 3000 Index
Section 3000 AIR OPERATED SPRAY DISPENSERS - CENTRAL ACRYLIC RESERVOIR...36 Versatile type of lubrication able to feed liquid to elevated, distant or inaccessible points. CONVEYOR CHAIN LUBRICATION SCHEMATIC...39
More informationAUTOMATIC GAS MANIFOLDS
AUTOMATIC GAS MANIFOLDS Phoenix Pipeline Products Limited. Unit 8, McKenzie Industrial Park, Tel No.: 44 (0) 161 428 7200 Bird Hall Lane, Fax No.: 44 (0) 161 428 7010 Stockport, Email: info@p3-phoenix.com
More informationAUTOMATIC TIRE INFLATOR # MW-60, MW-60-4WAY & MW-64HP
USER MANUEL AUTOMATIC TIRE INFLATOR # MW-60, MW-60-4WAY & MW-64HP TIRE EQUIPMENT MANUFACTURER 1.866.409.RACK WWW.MARTINSINDUSTRIES.COM info@martinsindustries.com PARTS Verify that the following components
More informationUser Manual for the Mars Calibration Bench
User Manual for the Mars Calibration Bench Fall 2013 Table of Contents Table of Contents Table of Contents... iii Introduction... v Chapter 1: The Mars Calibration Bench... 1 What Is the Mars Calibration
More informationOperation Manual Piston Sensed Gas Pressure Regulators
687 Technology Way Napa, CA 94558 Phone: (707) 259-0102 FAX: (707) 259-0117 www.aptech-online.com Operation Manual Piston Sensed Gas Pressure Regulators (Models KT9, KT10, Welded KT10, KT12) Table of Contents:
More information