STANDARD OPERATING PROCEDURE FORCE DIAL FDN 100
|
|
- Bethany Singleton
- 5 years ago
- Views:
Transcription
1 Page 1 of 5
2 1. Scope This Standard Operating Procedure (SOP) applies to the staff and students using the Force Dial FDN 100 in the Pharmacy Practice Resource Unit (PPRU) at the Pharmacy Department, University of Malta. 2. Objective To describe the procedure for the operation and calibration of the Force Dial FDN Definitions 3.1. Force Dial FDN 100: A dial gauge designed for routine hand-held force testing with the option of obtaining both tension and compression results. It may also be used as an algometer to test pain threshold, pain tolerance, trigger and tender points as well as to monitor treatment progress Hook: Attached to the device through a hole in its body and is used to measure tension forces Compression Head: Attached to the other end of the device and is used to measure compression forces. 4. Responsibility 4.1. The members of the Department of Pharmacy (staff and students) are responsible for following this SOP The designated Laboratory Officer or Laboratory Assistant is responsible for ensuring that this SOP is followed. Page 2 of 5
3 5. Procedure 5.1. Operation Apply a force to the compression head or hook in an axial position Follow the pointer to read the maximum force that is being applied Press the peak hold button to return the pointer to the resting position Calibration Obtain a standard test weight that is equal to the most frequently used range of force Suspend the standard test weight on the hook Check that the result obtained does not vary by more than +/- 1 graduation from the scale. Page 3 of 5
4 5.3. Flow Charts Operation Start Apply a force to compression head or hook in an axial position Follow the pointer to read the maximum force being applied Press peak hold button to return pointer to resting position End Calibration Start Obtain standard test weight equal to the most frequently used range of force Suspend standard test weight on hook Check that result obtained does not vary by > +/- 1 graduation from the scale End Page 4 of 5
5 6. Precautions 6.1. Verify the level of accuracy with standard test weights prior to using the device Exercise the plunger in and out for about 10 seconds before use to ensure that it is functioning properly Note that there is no zero on the dial and the graduations actually begin at 1kg or 10N Do not press the peak hold button whilst performing a force test Do not lubricate any part of the dial since oil residues will accumulate dust resulting in increased friction and decreased accuracy Contact the supplier if inaccurate readings are being obtained and do not attempt to adjust the device yourself since this may further damage its gauge. 7. Reference Wagner Instruments. FORCE DIAL FDK/FDN Series Push Pull Force Gage operation manual. Greenwich: Wagner Instruments. 8. Appendices N/A 9. Revision History Version Number Amendments/ Reasons for change 01 Initial Release 02 Inclusion of subheading titles of Procedure section in Table of Contents Page 5 of 5
STANDARD OPERATING PROCEDURE FORCE DIAL FDN 100
Table of Contents 1. Scope 2 2. Objective 2 3. Definitions 2 4. Responsibility 2 5. Procedure 3 6. Precautions 5 7. References 5 8. Appendices 5 9. Revision History 5 Page Original Authorised Copy for:
More informationSTANDARD OPERATING PROCEDURE VORTEX-GENIE 2
Table of Contents Page 1. Scope 2 2. Objective 2 3. Definitions 2 4. Responsibility 2 5. Procedure 3 5.1. Installation 3 5.2. Operation 3 5.3. Maintenance 4 5.4. Flow charts 5 6. Precautions 8 7. References
More informationSTANDARD OPERATING PROCEDURE
Table of Contents Page 1. Scope 2 2. Objective 2 3. Definitions 2 4. Responsibility 2 5. Procedure 3 6. Precautions 7 7. References 7 8. Appendices 7 9. Revision History 7 Original Authorised Copy for:
More informationSTANDARD OPERATING PROCEDURE ARTSANA MERCURY SPHYGMOMANOMETER
Page 1 of 8 1. Scope This Standard Operating Procedure (SOP) applies to the staff and students using the Artsana Mercury Sphygmomanometer in the Pharmacy Practice Resource Unit (PPRU) at the Pharmacy Department,
More informationSTANDARD OPERATING PROCEDURE
Table of Contents 1. Scope 2 2. Objective 2 3. Definitions 2 4. Responsibility 2 5. Procedure 2 6. Precautions 8 7. References 8 8. Appendices 8 9. Revision History 8 Page Original Authorised Copy for:
More informationSTANDARD OPERATING PROCEDURE
Ref.. Table of Contents Page 1. Scope 2 2. Objective 2 3. Definitions 2 4. Responsibility 3 5. Procedure 3 6. Precautions 14 7. References 14 8. Appendices 14 9. Revision History 14 Original Authorised
More informationOPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS Air Entrainment Meter ELE International Chartmoor Road, Chartwell Business Park Leighton Buzzard, Bedfordshire, LU7 4WG England phone: +44 (0) 1525 249200 fax: +44 (0) 1525 249249
More informationCertified Accuracy. Ring Force Gauge. Models and Capacities Available. Design and Principle of Operation
Certified Accuracy Ring Force Gauge The accurate measurement of mechanical forces is required in hundreds of applications from a simple weighing procedure to the calibration of testing machines and load
More informationSAUTER FK Version /2016 GB
Sauter GmbH Ziegelei 1 D-72336 Balingen E-Mail: info@sauter.eu Tel: +49-[0]7433-9933-199 Fax: +49-[0]7433-9933-149 Internet: www.sauter.eu Instruction Manual Digital Force Gauge SAUTER FK Version 1.4 12/2016
More informationTEST FOR STABILOMETER VALUE OF BITUMINOUS MIXTURES
Test Procedure for TEST FOR STABILOMETER VALUE OF BITUMINOUS MIXTURES TxDOT Designation: Tex-208-F Effective Date: February 2005 1. SCOPE 1.1 Use this test method to determine the Hveem stability value
More informationproduct manual H-1200 & H-1250 Universal and Portable Penetrometers
07.09 product manual H-1200 & H-1250 Universal and Portable Penetrometers Introduction Universal Penetrometer H-1200 Direct-reading instrument for precision penetration measurements of bituminous materials,
More informationTitle: Standard Operating Procedure for R&R Environmental Devices Model MFC201 Gas Dilution Calibrator
Procedure No: SOP-029 Revision No: 1.1 (December 29, 2010) Page No.: 1 of 7 1. INTRODUCTION AND SCOPE To obtain timely data for the purpose of air quality assessment, air quality trend reporting, air quality
More informationOperating Instructions Part No
DIGITAL AUTOMATIC TYRE INFLATOR Operating Instructions Part No. 11.0578 Thank you for selecting this Jamec Pem Automatic Tyre Inflator. Please read this manual before carrying out any installation or service
More informationTECHNICAL MANUAL CALIBRATION PROCEDURE FOR PRESSURE GAUGE. This publication replaces T.O. 33K dated 30 January 2012.
TECHNICAL MANUAL CALIBRATION PROCEDURE FOR GAUGE This publication replaces T.O. 33K6-4-427-1 dated 30 January 2012. Distribution Statement C - Distribution authorized to U. S. Government agencies and their
More informationOperating Instructions Part No
DIGITAL AUTOMATIC TYRE INFLATOR Operating Instructions Part No. 11.0545 Thank you for selecting this Jamec Pem Automatic Tyre Inflator. Please read this manual before carrying out any installation or service
More informationSERVICE BULLETIN. TOPIC: Cylinder NUMBER: SUPERSEDES: NEW DATE: May 15, Indexing Basic Cylinder Height On CFR F-1/F-2 Rating Units
SERVICE BULLETIN TOPIC: Cylinder NUMBER: 4-013 SUPERSEDES: NEW DATE: May 15, 2004 MODELS APPLICABLE TO: TEST METHOD: ROUTE TO: F-1 Research D 2699 F-2 Motor D 2700 F-1/F-2 Combination D 2699, D 2700 F-4
More informationANALOG PRESSURE GAUGE
304-00103 ANALOG PRESSURE GAUGE CALIBRATION PROCEDURE BARFIELD P/N 304-00103 20-304-00103 August 6, 2013 BARFIELD, INC. Corporate Headquarters 4101 Northwest 29th Street Miami, Florida 33142 www.barfieldinc.com
More informationPT Series Tension Gauges
PT Series Tension Gauges Model PT-1 Cable size 3/32", 1/8", 5/32" Model PT-1M Cable size 2.5mm, 3mm, 4mm Model PT-2 Cable size 3/16", 7/32", 1/4" Model PT-2M Cable size 5mm, 6mm, 7mm Model PT-3 Cable size
More informationAttachment C. Standard Operating Procedures. AMBIENT AIR MONITORING PROGRAM for the 130 LIBERTY STREET DECONSTRUCTION PROJECT
Attachment C Standard Operating Procedures AMBIENT AIR MONITORING PROGRAM for the 130 LIBERTY STREET DECONSTRUCTION PROJECT LOWER MANHATTAN DEVELOPMENT CORPORATION 1 Liberty Plaza New York, New York Prepared
More informationMAGNETIC CYCLING TRAINER SF-B0419 USER MANUAL
MAGNETIC CYCLING TRAINER SF-B049 USER MANUAL IMPORTANT: Read all instructions carefully before using this product. Retain owner s manual for future reference. For customer service, please contact: support@sunnyhealthfitness.com
More informationSTANDARD OPERATING PROCEDURE ADVANCED INTRAVENOUS TRAINING ARM (S )
Page 1 of 27 1. Scope This Standard Operating Procedure (SOP) applies to the staff and students using the Advanced Intravenous Training Arm in the Pharmacy Practice Resource Unit (PPRU) at the Pharmacy
More informationWIKA INSTRUMENT CORPORATION
WIKA INSTRUMENT CORPORATION Instruction Manual DIFFERENTIAL PRESSURE GAUGE Series 1500 Series 1000 Series 300 WIKA Instrument Corporation 1000 Wiegand Boulevard Lawrenceville, GA 30043 1-888-945-2872 http://www.wika.com
More informationTEST SPECIFICATION NYT-909-C
748 Starbuck Ave, Watertown, NY 13601 Phone: +1-315-786-5200 Engineering Fax: +1-315-786-5673 TEST SPECIFICATION NYT-909-C CODE OF TESTS FOR TESTING "AB" TEST RACK P/N 702546 & 702612 ISSUE NO. 5 1.0 THE
More informationTest pumps. Pressure sources. Good reasons for proper and reliable calibration
Test pumps Pressure is one of the most commonly measured quantities in engineering, which is why exact and reliable pressure measurement is especially important. However, the characteristics of the even
More informationTechnical Procedure for General Laboratory Equipment
Technical Procedure for General Laboratory Equipment 1.0 Purpose - This procedure specifies the required elements for the use of general laboratory equipment. 2.0 Scope - This procedure applies to all
More informationAR-15 CLEANING PROCEDURE. By: Joshua Blackwell, Eunice Perez-Rios, and Taylor Westfall
AR-15 CLEANING PROCEDURE By: Joshua Blackwell, Eunice Perez-Rios, and Taylor Westfall Table of Contents iii Table of Contents... iii Introduction... v Disassembly... 3 Cleaning and Lubricating Your Rifle...
More informationAustralian Standard. Bourdon tube pressure and vacuum gauges AS
AS 1349 1986 Australian Standard Bourdon tube pressure and vacuum gauges [Title allocated by Defence Cataloguing Authority: GAUGES, PRESSURE AND VACUUM (Bourdon Tube Type)... NSC Gp 66] This Australian
More informationStandard Recommended Practice. Field Measurement of Surface Profile of Abrasive Blast-Cleaned Steel Surfaces Using a Replica Tape
NACE Standard RP0287-2002 Item No. 21035 Standard Recommended Practice Field Measurement of Surface Profile of Abrasive Blast-Cleaned Steel Surfaces Using a Replica Tape This NACE International standard
More informationTitle: Standard Operating Procedure for Sabio 2010 and 4010 Dilution Calibrator
Procedure No: SOP-012 Revision No: 1.2, January 27, 2011 Page No.: 1 of 7 1. INTRODUCTION AND SCOPE This procedure is intended to describe the operations of the Sabio model 2010 and 4010 dilution calibrators.
More informationTechnical Procedure for Instrument Calibration and Maintenance
Technical Procedure for Instrument Calibration and Maintenance 1.0 Purpose To outline the schedules and procedures involved in the maintenance and verification of critical instrument calibration in the
More informationNo. 2 TEST WEIGHT ASSESSMENT
No. 2 TEST WEIGHT ASSESSMENT Version 2 This edition published December 2017 Australian Grain Industry Code of Practice http://www.graintrade.org.au/node/670 Technical Guideline Document No. 2 Test Weight
More informationInstrument Installation and Performance Verification
Instrument Installation and Performance Verification NOTICE: This document is intended solely as a guide to proper care and use Reichert instrumentation. Instrument Set-Up, Calibration, and Performance
More informationModel 130M Pneumatic Controller
Instruction MI 017-450 May 1978 Model 130M Pneumatic Controller Installation and Operation Manual Control Unit Controller Model 130M Controller is a pneumatic, shelf-mounted instrument with a separate
More informationTitle: Standard Operating Procedure for Dasibi Model 5008 Gas Dilution Calibrator
Procedure No: SOP-034 Revision No: 1.0 Revised Dec. 29, 2010 Page No.: 1 of 10 1. INTRODUCTION AND SCOPE This procedure is intended to describe the operations of the Dasibi model 5008 calibrator. The Dasibi
More informationNOTES TABLE OF CONTENTS
NOTES TABLE OF CONTENTS 1.0 Introduction.................................................. 2 1.1 Unpacking 1.2 Complete Kit 2.0 Operating Procedures.......................................... 3 2.1 Memory
More informationWARNING NOTES TABLE OF CONTENTS
NOTES TABLE OF CONTENTS 1.0 Introduction.................................................. 2 1.1 Unpacking 1.2 Complete Kit 2.0 Operating Procedures.......................................... 3 2.1 Memory
More informationStandard Operating Procedure. Air Displacement Pipette Calibration
University of Colorado at Denver October 28, 2003 - Revision 1.00 Page 1 of 7 1 Background: Standard Operating Procedure An accurate pipette is one of the most important tools in performing accurate analytical
More informationRevised on : 05. Jun TECHNICAL GUIDE PARTS CATALOGUE. Cal.VD51C ANALOGUE QUARTZ. SII Products
Revised on : 05. Jun. 2018 TECHNICAL GUIDE & PARTS CATALOGUE ANALOGUE QUARTZ [SPECIFICATION] Item PARTS CATALOGUE / TECHNICAL GUIDE Cal. No. Movement Movement size Outside diameter Casing diameter Total
More informationTitle: Standard Operating Procedure for Elemental and Organic Carbon (EC and OC) using Non-Dispersive Infrared Detection (NDIR)
Procedure No: SOP-025 Revision No: 1.0 (January 21, 2011) Page No.: 1 of 8 1. INTRODUCTION AND SCOPE To obtain timely data for the purpose of air quality assessment, air quality trend reporting and to
More informationTHE UNIVENTOR 400 ANAESTHESIA UNIT
THE UNIVENTOR 400 ANAESTHESIA UNIT TABLE OF CONTENTS EDITION 3 Section 1 - WARRANTY & SERVICE 1.1. WARRANTY 2 1.2. DAMAGED SHIPMENTS 2 1.3. SERVICE 2 Section 2 - INTRODUCTION 2.1. INTRODUCTION 3 Section
More informationDPC-30 DPC-100. Reference Manual
DPC-30 DPC-100 Reference Manual 1. Introduction 1.1 Description The Martel DPC Digital Pneumatic Calibrator improves upon traditional dial gauge pneumatic calibrators. The Martel DPC improves accuracy,
More informationRASP RX3 Feed UnitTM SPONGE-JET USER MANUAL. Sponge-Jet, Inc. (USA) 14 Patterson Lane Newington, NH
SPONGE-JET RASP RX3 Feed UnitTM USER MANUAL Sponge-Jet, Inc. (USA) 14 Patterson Lane +1-603-610-7950 Newington, NH 03801 www.spongejet.com Sponge-Jet RASP RX3 User Manual - REV A / DOC: MKT-014-ENG SPONGE-JET
More informationSPLIT HOPKINSON PRESSURE BAR OPERATIONS MANUAL 5/9/2014
B Calibration of Split Hopkinson Pressure Bar Setup: Calibration is performed by comparing the wave speed of the initial pulse versus the reflected pulse and calculating the Energy Ratio. This ratio gives
More informationMET 335W Fluid Mechanics Laboratory. Lab 1: Bourdon Tube Calibration. Nick Peak
MET 335W Fluid Mechanics Laboratory Lab 1: Bourdon Tube Calibration Nick Peak January 15, 2018 Purpose The purpose of this experiment is to test the accuracy of a bourdon pressure gauge. This is accomplished
More information1811G/H PITOT-STATIC TEST SET
1811G/H PITOT-STATIC TEST SET USER INSTRUCTION MANUAL M/N: 1811G/H, P/Ns: 101-00165 101-00168 101-00169 Doc. P/N: 56-101-00165_00168_00169 Revision C December 9, 2014 BARFIELD, INC. Corporate Headquarters
More informationMANUAL BE SERIES Test Benches
The CustomCrimp Manual BE Series Test Benches are designed with features that make proof and burst testing of hydraulic hose assemblies a quick and easy procedure. CUSTOMIZED AND SPECIAL DESIGN BENCHES
More informationPipetting and Determining Protein Concentration
Pipetting and Determining Protein Concentration Background Information: When performing experiments in Cell Biology, it is often necessary to use very small volumes of reagents sometimes because the reagents
More informationLaboratory #2 Pipetting Technique and Micropipette Calibration Skills=40 pts
Laboratory #2 Pipetting Technique and Micropipette Calibration Skills=40 pts Objectives: Upon completion of this unit, the student should be able to: 1. List and describe 3 categories of pipets. 2. List
More informationBristol Fire Department Standard Operating Procedures. Multi Gas Detector
Bristol Fire Department Standard Operating Procedures January 31, 2018 Bristol Fire Department Standard Operating Procedures Table of Contents s 1-01 Bump Test 1-02 Fresh Air Setup 2-01 Monthly Calibration
More informationFTC130 Transmitter. Operating Manual
Seite 1 von 11 FTC130 Transmitter Fast Thermal Conductivity Analyzer Operating Manual 1.09KD180724CWI1V05 Messkonzept GmbH Seite 2 von 11 1. Intended Use... 3 2. Description... 4 3. Measuring gases and
More informationDigital pressure gauge Model CPG500
Calibration technology Digital pressure gauge Model CPG500 WIKA data sheet CT 09.01 Applications Calibration service companies and service industry Measurement and control laboratories Quality assurance
More informationANZAI AZ-733VI. Respiratory Gating System. since 1976
ANZAI since 1976 Respiratory Gating System AZ-733VI Specifications AZ-733VI Dimension Configuration Options Sensor Port W:260 D:230 H:126mm Sensor Port Laser Sensor & Fixing Arm Relay Box Wave Monitor
More informationModel 23H Hand Crank Seamer
OPERATOR'S MANUAL Model 23H Hand Crank Seamer If you are not experienced with your seamer, please read and understand this manual before operating the machine. If you have a question discuss it with your
More informationUser Manual for the Mars Calibration Bench
User Manual for the Mars Calibration Bench Fall 2013 Table of Contents Table of Contents Table of Contents... iii Introduction... v Chapter 1: The Mars Calibration Bench... 1 What Is the Mars Calibration
More informationCentriFlow Meter Integrated Air Entrainment System
CentriFlow Meter Integrated Air Entrainment System INSTALLATION & OPERATION MANUAL January 2004 Revision 021-4 EASTERN INSTRUMENTS 416 LANDMARK DR. WILMINGTON, NC 28412 910-392-2490 Fax: 910-392-2123 website:
More informationTECHNICAL MANUAL CALIBRATION INSTRUCTIONS FUEL PRESSURIZING & DUMP VALVE TEST STAND 1TL
TECHNICAL MANUAL CALIBRATION INSTRUCTIONS FUEL PRESSURIZING & DUMP VALVE TEST STAND 1TL32-6228-1 Rev 1.0 3-Oct-2008 PWA 15090G-OC001 DISCLOSURE NOTICE: This information is furnished upon the condition
More informationPosiTector UTG, UTG-STD & UTG-ME
Management Procedure 2585 Revision: E Date Issued: Feb 21, 2003 Date Revised: 14 August 2009 Calibration Procedure DeFelsko Corporation PosiTector UTG, UTG-STD & UTG-ME Ultrasonic Thickness Gage Table
More informationCÜBE. User Manual. American Weigh Scales. CUBE-100 (100g x 0.01g) CUBE-650 (650g x 0.1g)
American Weigh Scales CÜBE User Manual CUBE-100 (100g x 0.01g) CUBE-650 (650g x 0.1g) Copyright 2014 American Weigh Scales, Inc. All rights reserved. Rev. 1.0 CUBE Manual Thank you for purchasing the American
More informationDiscontinued. Powers Controls. Technical Instructions Document No P25 RV Rev. 1, May, RV 201 Pressure Reducing Valves.
Powers Controls RV 201 Pressure Reducing Valves Description Features Product Numbers Dual Pressure PRV Technical Instructions Document No. 155-049P25 RV 201-1 Single Pressure PRV The RV 201 Pressure Reducing
More informationOperating manual for the pressure transducer unit CCS 1000
Operating manual for the pressure transducer unit CCS 1000 Please read the operating manual before using the device. 1 Content: 1. General description 2. Technical data 3. Operation 4. Scope of supply
More informationAir Operated Hydraulic Pumping Systems to 50,000 psi
High Pressure Equipment Air Operated Hydraulic Pumping Systems to 50,000 psi PS-10: 10,000 psi PS-20: 20,000 psi PS-30: 30,000 psi PS-40: 40,000 psi PS-50: 50,000 psi PS-90: 90,000 psi High Pressure air
More informationINSPECTION OF MEDICINAL GASES
PHARMACEUTICAL INSPECTION CONVENTION PHARMACEUTICAL INSPECTION CO-OPERATION SCHEME PI 025-2 25 September 2007 AIDE-MEMOIRE INSPECTION OF MEDICINAL GASES PIC/S September 2007 Reproduction prohibited for
More informationDIGITAL AUTOMATIC TYRE INFLATOR
DIGITAL AUTOMATIC TYRE INFLATOR Instruction Manual PSI Part No. 11.0556 Digital Automatic Tyre Inflator (Portable) Thank you for selecting our Digital Automatic Tyre Inflator (Portable), please read this
More informationMr Roger Wood Measurement & Process Group (M&P) Network Strategy National Grid Gas plc Brick Kiln Street Hinckley Leicestershire LE10 0NA
Mr Roger Wood Measurement & Process Group (M&P) Network Strategy National Grid Gas plc Brick Kiln Street Hinckley Leicestershire LE10 0NA Dear Roger, Your Ref: Our Ref: Direct Dial: 020 7901 7468 Email:
More informationSEMMME3-073 Checking that completed assemblies comply with specification
Checking that completed assemblies comply with specification Overview This unit identifies the competences you need to carry out checks on mechanical assemblies, in accordance with approved procedures.
More informationDX2/DXX Operating Instructions
CHECK LINE BY ELECTROMATIC DX2/DXX Operating Instructions CHECK LINE INSTRUMENTS ELECTROMATIC E Q U I P M E N T C O., I N C. 600 Oakland Ave., Cedarhurst, NY 11516 U.S.A. TEL: 516-295-4300 FAX: 516-295-4399
More information159 mm 154 mm. Subject to changes 10/2012
Low-pressure calibrator LPX calibrator medium: air / up to 10 bar KELLER pressure calibrators are highly accurate calibration instruments which are available for the following pressure ranges: -0,85 10
More informationHPICAL Operation & Data Logging Procedures. Click spacebar to advance through slides 1
HPICAL-15000 Operation & Data Logging Procedures Click spacebar to advance through slides 1 WARNING Always wear proper safety equipment when using high pressure equipment. Do not exceed 125 psi air pressure.
More informationCautions : 1. The gauge orientation on the GPU and GPM types can be changed by using
The compact-size pressure gauge can be installed in small spaces. With the built-in tube fitting type, tube connection is the only necessary step before pressure indication. Fluid medium Indicated pressure
More informationCopyright 2004 by the Thomas G. Faria Corporation, Uncasville CT No part of this publication may by reproduced in any form, in an electronic
Copyright 2004 by the Thomas G. Faria Corporation, Uncasville CT No part of this publication may by reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission
More informationInstruction Manual. CG16K Barometrically Compensated Capsule Dial Gauge. CG16K Capsule Dial Gauge, 0 to 25 mbar
Instruction Manual D356-10-880 Issue G Original CG16K Barometrically Compensated Capsule Dial Gauge Description CG16K Capsule Dial Gauge, 0 to 1040 mbar CG16K Capsule Dial Gauge, 0 to 125 mbar CG16K Capsule
More informationPRODUCT DATA SHEET. Description
PRODUCT DATA SHEET Series 820 Digital Flow Meter Description of Included Models Model Number 825 Description All the great standard features of the Sotera digital meters can be found on the model 825,
More informationOPERATING PROCEDURE. Number: V2. Authors. Approvals
OPERATING PROCEDURE Title: Calibration of the Denver XL5K Top-Loading Balance (Note: This SOP is for demonstration purposes, and has numerous problems) Effective Date: April 30, 2003 Author Date: October
More informationTECHNICAL INFORMATION SHEET 17. Revision 1 : 2016 MODEL RISK ASSESSMENT FOR THE MANUAL HANDLING OF GAS CYLINDERS
TECHNICAL INFORMATION SHEET 17 Revision 1 : 2016 MODEL RISK ASSESSMENT FOR THE MANUAL HANDLING OF GAS CYLINDERS Copyright 2016 by British Compressed Gases Association. First printed 2009. All rights reserved.
More informationCalibration Procedure
Management Procedure 2565 Revision: A Date Issued: October 30, 2017 Date Revised: Calibration Procedure DeFelsko Corporation PosiTector RTR-3D Replica Tape Reader Probe Table of Contents 1 Introduction
More informationAPPLICATION NOTE AN-2100 PREVENTIVE MAINTENANCE OF FIBER OPTIC CABLES AND FINISAR OPTICS
APPLICATION NOTE AN-2100 PREVENTIVE MAINTENANCE OF FIBER OPTIC CABLES AND FINISAR OPTICS The end of a fiber optic cable and the inner surface of an optical module lens constitute optical surfaces that
More informationLiquid Handling Systems
Liquid Handling Systems 1.0 Purpose - This procedure specifies the required elements for the maintenance and use of the Hamilton- Microlab 1000 Plus and the Microlab 500 Liquid Handling Systems. 2.0 Scope
More informationPage 2 of 10. SOP SF SOP For LN 2 System and LN 2 Freezer Room Operations
Page 2 of 10 alarm. Communications with the supplier, Praxair, are critical to the maintenance of the LN2 system and are addressed in this SOP. 4. SCOPE 4.1. The scope of this procedure includes all trained
More informationOperation Manual - PN A MENSOR MODEL 73 SHOP AIR BOOSTER
Operation Manual - PN 0017946001 A MENSOR MODEL 73 SHOP AIR BOOSTER Mensor Model 73 Shop Air Booster System (750 psi Version) April 23, 2012 Trademarks / Copyright Mensor is a registered trademark of Mensor
More informationIssue Date: Effective Date: Supersedes: V-15 (rev. 2)
Bulletin Category: VOLUME Bulletin: V-15 (rev. 3) Page: 1 of 6 Manual Correction of Measured Liquid Volumes to Equivalent Volumes at Reference Conditions 1.0 Scope This bulletin communicates the policy
More informationChain Installation Guide
Chain Installation Guide How to Install Chain Reasons for installing a new chain: 1 Extend the life of your gears and overall drivetrain 2 Better Performance 3 Safety Installation You will need: Chain
More informationRH800 & 2000 BASIC OPERATIONS
RH800 & 2000 BASIC OPERATIONS 2 General information This manual contains technical information regarding Bayer SeedGrowth Equipment. Please read and understand these instructions completely before proceeding
More information3/2-way valve, Series CD07 Qn= 1400 l/min pipe connection compressed air connection output: G 1/4 - M14x1,5 suitable for ATEX
/-way valve, Series CD07 Version Spool valve, zero overlap Sealing principle soft sealing Working pressure min./max. -0.95 bar / 0 bar Ambient temperature min./max. -5 C / +80 C Medium temperature min./max.
More informationTactical Sniper air rifle & carbine
Tactical Sniper air rifle & carbine User instruction manual Fill pressure: 200 bar (approximately 2,900 psi) Rev 4/17 Contents Rules of safe shooting... 3 Filling your rifle... 4-5 Loading the magazine...
More information632 AccuPro Set-up & Operation
632 AccuPro Set-up & Operation Always check: Reel & Roller bearings Bent or broken blades Make sure the reel spins freely in the frame Place the Reel Into the Machine There are three lifting options for
More information170-CG Feed Unit SPONGE-JET USER MANUAL. Sponge-Jet, Inc. (USA) 14 Patterson Lane Newington, NH
SPONGE-JET 170-CG Feed Unit USER MANUAL Sponge-Jet, Inc. (USA) 14 Patterson Lane +1-603-610-7950 Newington, NH 03801 www.spongejet.com AUGUST 2014, Sponge-Jet 170-CG User Manual - REV A / DOC: M-MKTG-002ENG
More informationFUCILI GUNS FUSILS FUSILES
FUCILI GUNS FUSILS FUSILES 4 Congratulations! The product you purchased, which is the result of continuous research and development, is made in compliance with CRESSI-SUB quality standard, thus ensuring
More informationSEMPEO SQA Unit Code FP2M 04 Maintaining mechanical devices and equipment
Overview This standard covers a broad range of basic mechanical maintenance competences that will prepare you for entry into the engineering or manufacturing sectors, creating a progression between education
More informationSUPER PRECISION AIR RELAYS
CAT. No. KS-128E SUPER PRECISION AIR REGULATOR rsseries SUPER PRECISION AIR REGULATORS rr SERIES SUPER PRECISION AIR RELAYS Air Pressure Regulators that attain the ultimate in pressure control. S/R R SUPER
More informationPAT I E N T I N S T R U C T I O N S
PATIENT INSTRUCTIONS Table of Contents Welcome Step 1 // Loosen the Socket Step 2 // Release Air from Air Bladders Step 3 // Put Infinite Socket On: Pin Lock/Seal-In Step 4 // Tighten BOA Reel Step 5 //
More informationP5513. Users Manual. Pneumatic Comparison Test Pump. Test Equipment Depot Washington Street Melrose, MA TestEquipmentDepot.
Test Equipment Depot - 800.517.8431-99 Washington Street Melrose, MA 02176 TestEquipmentDepot.com P5513 Pneumatic Comparison Test Pump Users Manual PN 3963372 November 2010 2010 Fluke Corporation. All
More informationDigital pressure gauge Model CPG500
Digital pressure gauge Model CPG500 WIKA data sheet CT 09.01 for further approvals see page 3 Applications Calibration service companies and service industry Measurement and control laboratories Quality
More informationSpecifications Testing & Adjusting Disassembly & Assembly
SB4191E00 Jul. 2005 Specifications Testing & Adjusting Supplement for Quad Lift Mast D20/25/30/32/33S-3 G/GC20/25/30/32P-3 G/GC20/25/30/32E-3 Important Safety Information Most accidents involving product
More information6 digital caliper with case
6 digital caliper with case Model 98563 Set up And Operating Instructions Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly
More informationBY HYDROHOIST BOATLIFTS
BY HYDROHOIST BOATLIFTS OWNER S MANUAL US PATENT # 6,422,167 B1 REVISED: June 21st 2018 800.825.3379 BOATLIFT.COM Thank You We would like to a moment to thank you for purchasing a HarborHoist TM G1.5 lift.
More informationOPERATION and MAINTENANCE Guide
Catalog No. AIR1000 Winch and Hoist OPERATION and MAINTENANCE Guide Cat. No. AIR1000 1250 Lb. Single Line Pull READ THIS BEFORE OPERATING UNIT INSTALLATION: Mount on clean, flat surface. Use 1/2" mounting
More informationINDUSTRIAL HYGIENE GROUP Standard Operating Procedure. TVA-1000 PID/FID Portable Toxic Vapor analyzer. 1 of 9. Contents
1 of 9 1.0 Purpose & Scope 2.0 Responsibilities 3.0 Definitions 4.0 Prerequisites 5.0 Precautions 6.0 Procedure 7.0 Implementation And Training 8.0 References 9.0 Attachments 10.0 Documentation Contents
More informationTemperature gauge Installation Guide
Temperature gauge Installation Guide improper functioning, or damage. Additional information can be found at: CAUTION: Read this installation guide carefully before unpacking the temperature gauge. Improper
More informationBeeman Precision Airguns Spring-Piston Air Rifles P1, P3, P11
Beeman Precision Airguns Spring-Piston Air Rifles P1, P3, P11 User Instruction Manual V1 10/17 CONTENTS Rules of safe shooting...3 Cocking & Loading... 4 Safety... 4 Sight Adjustment...5 Trigger Adjustment...5
More informationThermo Probe, Inc. TP-5 TP-7 TP-8. Instruction Manual English. Switch. Display. Carry Strap. Probe. Ground Clip. Switch. Display.
Display Thermo, Inc. Instruction Manual English TP-5 Display TP-7 Display TP-8 1-1 Thermo, Inc. Instructions for use- Models TP-5, TP-7, and TP-8 The manual describes basic function and use of Thermo instruments
More information