|
|
- Pamela Crawford
- 5 years ago
- Views:
Transcription
1
2
3
4
5
6
7 Making Sails Part 2 Making the Main By Daniel Bergan Sail Cloth Weight: A set- 50 micron B set- 75 Micron C set- 75 Micron D set- 75 Micron Clear your bench make sure it doesn t have any markings at all as the film when rolling the patches can be marked and dented very easily. I find the main is a little more straight forward to make then the Jib. For the main the template can be cut straight away, unlike the jib that requires the luff tape to allow for the jib wire to be fit before cutting to template size. Make sure you have a good clean working area. Ensure your templates are correct, and roll out your film to be cut to shape. I like to weigh down the template with weights to prevent any movement while cutting around the template. It just makes it easier. Another product that is handy at times is Artist spray adhesive, this has a low tac allowing the sail cloth to stay in position while being cut and easily removed. The only thing is sometimes the residue can sometimes stay on the sail and needs to clean off with soapy water afterwards. But this good for large sails. Its like and extra pair hands. Weighing down the template for cutting
8 Once the template is cut out remove everything from the bench other then the sail ready to have the trim added. As mentioned prior I use a plotter cutter to make all my corner reinforcements. You can cut them out by hand hand from polyester insignia cloth. Its much easier having these prep cut ready to go. Plotter cut corners ready to be used Carefully stick on the patches, you only get one chance to stick these on. Mess it up and you start again from the beginning. Some times you need to trim the edges if it moved slight off line just keep within the sail plan. Please take care while sticking these corners on. Repeat the process doing one side then turning over to do the other side. Corners stuck on and trimmed to sail plan
9 After the patches are on the next thing to add are the sail battens. Now the battens can be made from any material you like. The length of the battens and were they are fasten to the sail is critical to get right. There is some flexibility but you must remain within the rules. To help with this I pre mark my Templates showing exactly were I want the battens fitted. Batten material can be plastic, Fibre glass and Carbon fibre etc. I fine plastic battens work the best with these sails. I use off the shelf.5mm plastic sheet, you can buy these from any good hobby shop. These come in clear or White in colour. I then use a wider double side tape and stick one side to the plastic sheet and then begin to cut with a Stanley knife the width and length of the batten ready to use. It then a simple peal off the tape from the double sided tape and stick into position on your sail once cut to size. Its worth mentioning I use sail grade double sided tape, don t use craft double sided tape it just doesn t hold up over time. Clear Plastic.5mm sheet Double sided tape stuck to plastic ready to be cut to size. Cut Lengths ready to be used
10 Make sure you stick the battens were you need them to go. It also worth mentioning, what side do you put the battens and weather you stagger the battens and go alternate one side then the next goes the other side etc I tried having the battens all on one side( same as the produced ones) or alternate sides and found no difference in performance. So have a try yourself. Once the battens are in place stick the reinforcement patches over the top of the battens, this helps the batten to stay fasten to the sail.
11 Now the corners are in place and the battens are fasten on the next thin is to add the eyelets. I use a hole punch for the cutting of the holes for eyelets. Its easier and cleaner. The alternate is to use a heated nail or drill bit and melt a hole. Note I don t use Eyelets for the luff tie areas just reinforcement and 1mm hole from holes punch. After the eyelets are in and looking good its just add numbers and trim lines if you want them and class logo. I use thin Vinyl for all these items and use the plotter cutter to make what we need and colour options. There is nothing too hard and with practise you will find your sails will look and sail great. I hope this was helpful. Good luck and see you on the water.
Manual 1: working with cutting films. MANUAL 1. Working with cutting films. March 2017
Manual 1: working with cutting films. MANUAL 1 R Working with cutting films March 2017 Manual 1: working with cutting films. R 1 NECESSARY TOOLS It goes without saying that you need the right tools if
More informationPRE CUT CAR WINDOW TINTING INSTALLATION GUIDE
PRE CUT CAR WINDOW TINTING INSTALLATION GUIDE EXPERT APPROVED! FOR PRE-CUT CAR WINDOW TINT KITS THOUROUGH STEP BY STEP GUIDE CO-CREATED WITH ONE OF OUR EXPERTS INSIDER TIPS DETAILED COLOUR PHOTO REFERENCES
More informationCreative Arts Photography Dept 35 Section PH. Mounting Your Photographs
Creative Arts Photography Dept 35 Section PH Mounting Your Photographs Photography non- professional entry rules: - All photos must be taken by exhibitor - Sizes: 8x10 and 8x12 (if you are printing your
More informationHow Scott Builds a Fighter Kite, May 2011 Updated Sept 2018
How Scott Builds a Fighter Kite, May 2011 Updated Sept 2018 MAKE A TEMPLATE 1. Draw half sail plan on 17x22 pad with 4x4 (1/4 inch) grid. Add ¼ inch extra on nose (for reinforcement) and plenty of extra
More informationDRAGONFLITE 95 RESTRICTED CLASS RULES 2016
DragonFlite Force 95, Restricted Class Rules 2016 2013 Version 1.2 1.0 DRAGONFLITE 95 RESTRICTED CLASS RULES 2016 Version 1.2 DF Racing Rules Committee 2016 Introduction The DragonFlite 95 (DF95) project
More informationDRAGONFLITE 95 RESTRICTED CLASS RULES 2016
DragonFlite Force 95, Restricted Class Rules 2016 2013 Version 1.0 DRAGONFLITE 95 RESTRICTED CLASS RULES 2016 Version 1.0 DF Racing Rules Committee 2016 Introduction The DragonFlite 95 (DF95) project started
More informationHillbilly Golf. Included. Game Building Instructions. 2-foot Fence Building Instructions. Bolo making Instructions
Hillbilly Golf Game Building Instructions Included 2-foot Fence Building Instructions Bolo making Instructions Minus Bar Building Instructions and Minus bar play rules Plus some Extras! Hillbilly Golf
More informationTUNE YOUR SAILS SPEED. Optimist Tuning Guide. Photo Wavelength
TUNE YOUR SAILS FOR OUTRIGHT SPEED Photo Wavelength PEAK / HEAD THROAT TACK CLEW THANK YOU for choosing North Sails for your Optimist. Whether you are just starting out in an Optimist you are an experienced
More informationYou can use a variety of materials for this kite, such as Tyvek, ripstop nylon, Orcon, paper, or mylar or mylar-like plastic gift wrap films.
Woody's " Woodtick " Fighter Kite This kite is easy to make and easy to fly. It's performance will allow you to learn all fighter kite flying skills, plus put an ear to ear grin on your face. What more
More informationAn Australian Classic by spectre.com
An Australian Classic by www.go spectre.com Your Bug! Welcome to the Balain Bug experience!!!!!! The Bug kit has been designed so as to be a modern version of the Traditional Bug now you can sail like
More informationAMYA Soling 50 Class Rules
AMYA Soling 50 Class Rules - 2009 Overall General Specifications Length = 50 Overall Beam = 12 1/8 Overall Draft = 11 Sail Area = 800 Square Inches Displacement = 17 lbs. Minimum Mast Height = 61-1/4 Maximum
More information3190A NEO-ANGLE DOOR INSTALLATION INSTRUCTIONS. Series MODEL NO
NEO-ANGLE DOOR INSTALLATION INSTRUCTIONS Series 30A Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. The Exploded Diagram
More informationTrim Tab Wind Vane for boats with transom mounted rudders
Trim Tab Wind Vane for boats with transom mounted rudders If your boat has a transom mounted rudder, you can build this self-steering windvane for around $150, using regular wood working tools and some
More informationEaster Bunny Pompoms
Easter Bunny Pompoms When I was younger I remember it taking ages to make pompoms because of constantly passing a ball of yarn through the middle of two cardboard circles. Well this method makes it a lot
More informationGlitter, metallic belly, and stripes (left) and making use of ester egg wrappers (these leech colour with glue, so be careful).
Lure Making Part 2 Now the glue is dried yes, it should be dry by now), you can give the lure test swim. Be aware that if it s finely balanced, adding the hooks might change its buoyancy or motion so don
More informationBuilding the Japanese Arrow for target archery
Building the Japanese Arrow for target archery The purpose of this paper is to help target archers using a Japanese Yumi bow build accurate arrows for target archery. These arrows will have a period appearance
More informationAppendix 1: How To Install the Northeaster Dory Sailing Component Kit Upgrade
Appendix 1: How To Install the Northeaster Dory Sailing Component Kit Upgrade 143 Northeaster Dory Sailing Rig Upgrades: Adding sail track, an outhaul, and camcleats for the jib We ll start with the mast.
More informationPlans and Instructions to build a folding reflector oven
Plans and Instructions to build a folding reflector oven Kayak2go.com also has folding kayak plans available for purchase. The low cost and ease of construction make the folding kayaks a great youth group
More informationSailTrack Installation Instructions. External Track
SailTrack Installation Instructions External Track SH-500 SS SH-401 SS SH-600 SS SH-200B SS SH-200A SS www.tidesmarine.com Before You Begin Your installation will be easier if you move the boom well off
More information5. Tailplane assembly
5. Tailplane assembly Overview This section covers the fitting of your completed tailplanes to the torque tube assembly. Included is the insertion of the TP13 bushes in the inboard rib and the fitting
More informationMake Bruce's High Performance 'F3' Fighter Kite In Less Than 2 Hours For Under $3
Make Bruce's High Performance 'F3' Fighter Kite In Less Than 2 Hours For Under $3 This article was inspired from a chapter in NORTH AMERICAN FIGHTER KITES, my 400+ page fighter kite book on CD ROM. If
More informationKerry J. Ridgway, DVM Institute for Equine Therapeutic Options. Templates for Saddle Fitting
Kerry J. Ridgway, DVM Institute for Equine Therapeutic Options Templates for Saddle Fitting We need a system for determining the shape of the horse s back in the area the saddle will sit in order to even
More informationBuilding a Rocket (Advanced) Before you build a rocket try the bottle on the launcher to test if it holds pressure and fits correctly.
You Will Need 3X 2ltr Bottles 1X Paper lip 1X Glue/Double Sided Tape 1X ardboard 1X Bin Liner 1X Roll of Fishing Line or Thin s Sheets of Paper Side A of Fin 1X Hot Glue Gun 1X Pair of Scissors 1X Fine
More informationCarbo Racing Foil Instruction Manual Unit 0, 1, 2, 3
Carbo Racing Foil Instruction Manual Unit 0, 1, 2, 3 WARNING!: Strictly follow all instructions to avoid an accident, damage to your vessel, personal injury or death. See www.harken.com/manuals for additional
More informationTopaz OMEGA Rigging Instructions
Topaz OMEGA Rigging Instructions www.toppersailboats.com TOPAZ OMEGA RIGGING INSTRUCTIONS CONTENTS 02. Introduction 02. Manufacturers Details 03. Maintenance 04. Raising the Mast 05. Attaching the Boom
More informationWorld Robot Olympiad 2018
World Robot Olympiad 2018 WRO Football Field Version: Final Version January 15 th WRO Football Field 1. The Official WRO Football playing field is 1830 mm by 2430 mm. Local organisers may choose to use
More informationGrandpa's Homemade Rocket for About a Dollar!
Grandpa's Homemade Rocket for About a Dollar! Grandpa and Granny Co. 2012 The most common items needed: (The number of Rocket parts from each item is before the parts name and its proportionate cost is
More informationMiniOpti Optimist RC Dinghy CLASS RULES
MiniOpti Optimist RC Dinghy CLASS RULES 1. GENERAL - CLASS The Mini-Optimist as in the full sized Optimist Dinghy class is a One-Design Class. The objective being that the sailing skills of the skipper
More informationaero naut Order No. 3009/00
aero naut Order No. 3009/00 Introduction: The model should be assembled following the sequence of the stages of construction described in these instructions. The laser-cut components are individually numbered.
More informationGOODBUYS surplus sailcloth & sail making materials
GOODBUYS surplus sailcloth & sail making materials updated April 2018 SAILSETC Supplementary Price List SP 03 If you would like an up to date version of this list please contact the SAILSetc office ask
More informationAMYA SeaWind Class Rules
AMYA SeaWind Class Rules Revised 4/1/2011 1 GENERAL - CLASS: The SeaWind is a one design class. The class objective is competition where the skill of the skipper in sailing and adjusting his boat will
More informationWHITE WOLF. X-ray View MID POWER MODEL ROCKET KIT BUILDING INSTRUCTIONS KIT SPECIFICATIONS:
WHITEWOLF-38 PARTS LIST 1 - Nose Cone 1-17" Airframe 1-6" Motor Tube 3 - Aft Fins 3 - Forward Fins 2 - Centering Rings 1-15" Parachute 2 - launch lugs 1-12 Kevlar Shock Cord 1 - Motor Retention >>(screw/washer)
More informationGOODBUYS surplus sailcloth & sail making materials
GOODBUYS surplus sailcloth & sail making materials updated December 2016 SAILSETC Supplementary Price List SP 03 If you would like an up to date version of this list please contact the SAILSetc office
More informationMaking Jewel Beetle Wing and Abalone Shell Blanks. Contributed by: Cody Walker. A.K.A cwalker935
Making Jewel Beetle Wing and Abalone Shell Blanks Contributed by: Cody Walker A.K.A cwalker935 This tutorial was downloaded from http://www.penturners.org The International Association of Penturners -
More informationHUNTERS HELP TECHNOLOGIES
HUNTERS HELP TECHNOLOGIES www.huntershelp.com Hunters Help Technologies Field Dressing Guide HHT tools have been designed and manufactured to provide big game hunters a safer and more efficient means of
More informationBrushbot Kit Instructions: Parts
Brushbot Kit Instructions: Parts or AG13 Googly eyes Additional Tools Needed: Scissors or snips, hot glue gun or some type of glue suitable for plastic (epoxy or super glue should be fine). Brushbot Kit
More information3 SIZE NAGASAKI HATA
3 SIZE NAGASAKI HATA MADE FROM MODERN MATERIALS By Peter (P-air) Stauffer June 2000 The kite and resulting plans and instructions, I have made because of a request by Uli Wahl and Rico Argent, as Rico
More informationMarking films - Application guide
Marking films - Application guide The application techniques that we will describe should help users by making their job easier, or by saving them time. However, we know that all the advice in the world
More informationwww.aquaglidekayak.com WORK SPACE AND TOOLS 1. Take care to position yourself in a clean, dry area with good ventilation. For proper curing of adhesives, temperature should remain above 10 C (50 F).
More informationAMYA SeaWind Class Rules
AMYA SeaWind Class Rules Revised 4/1/2013 1 GENERAL - CLASS: The SeaWind is a one design class. The class objective is competition where the skill of the skipper in sailing and adjusting his boat will
More informationMounting the RoboFocus RF-3 Unit on the LX-200/400 MicroFocuser
Mounting the RoboFocus RF-3 Unit on the LX-200/400 MicroFocuser The RoboFocus unit can be mounted on the Meade MicroFocuser, commonly found on the LX-200/400 series. The RF folks point to this URL as a
More informationAustralia Newsletter DF95
Australia Newsletter DF95 DECEMBER 2017 Welcome to the DF95 Class newsletter. The DF95 is raced as a Restricted Class. This means that the boat is to be raced as supplied by the Builder, with any changes
More informationMarking films application guide
Marking films application guide The application techniques that we will describe should help users by making their job easier, or by saving them time. However, we know that all the advice in the world
More informationwww.allsportsystems.com Page 1 of 29 Page 2 of 29 Table of Contents Items You Supply: 4 MICROBAY Setup Instructions 5 Items Provided By AllSportSystems: 5 MEASURING AND CUTTING THE 1 EMT POLES FOR THE
More informationWe hope you ll enjoy the Drifter as much as we have! Scott DeTray Model Aero Specifications:
We are excited to bring you the Drifter RC airboat. You re probably thinking it doesn t fly so what is Model Aero thinking??? We have always liked RC vehicles of all types and have had a fondness for airboats
More informationHOW TO DIG A TEST PIT
HOW TO DIG A TEST PIT An archaeological test pit is a small 1m by 1m trench dug in a series of layers, or spits, to a depth of approximately 1m. The archaeological materials collected from these layers
More informationWhy Choose A Polymer Wall Swimming Pool?
WHY CHOOSE A WHY CHOOSE A Why Choose A Polymer Wall Swimming Pool? 3 4 CHAPTER 6 10 13 15 INTRODUCTION 1 What exactly is a Package Pool and More Specifically a Polymer Wall Swimming Pool? CHAPTER 2 The
More informationOur Spa covers. About Spa Cover Vinyl
Our Spa covers Whether you are in the market for a new Spa cover or just want to get the most out of your existing one, this guide will give you a wealth of helpful information. These basic maintenance
More informationYour kit contains the following items. Additional Items You May Need. Pre- cut parts Propeller rigging and rubber Sandpaper Covering sheet
Your kit contains the following items Pre- cut parts Propeller rigging and rubber Sandpaper Covering sheet The SkyFox offers great glide performance in a rubber powered plane due to its built up wing.
More informationPRODUCT BULLETIN AUTOMOTIVE FILMS FPP Auto A CONTENTS
PRODUCT BULLETIN AUTOMOTIVE FILMS FPP.7.3.2.Auto A 07.07 APPLYING AND REMOVING Solar protection film AUTOMOTIVE FILM MATERIAL REQUIRED PULVITRE (11-litre vaporiser) MARJO flexible squeegee MARBLEU soft
More informationFEATHER INLAYS. Custom Rod Builders Guild
FEATHER INLAYS Using Multiple Feathers by Neal Hall Custom Rod Builders Guild I have been building rods for about 10 years. Five years ago I became intrigued with a feather inlay designed by Charles Reading
More informationBUILD A BETTER BUBBLE BLOWER
Grades K 2, 3 5 20 60 minutes BUILD A BETTER BUBBLE BLOWER DESIGN CHALLENGE Design, build, and test a successful bubble blower. MATERIALS Supplies and Equipment: Shallow bowls or trays Scissors Towels
More informationVacuum Bagging Wings Instruction Manual Purdue University
Vacuum Bagging Wings Instruction Manual Purdue University Note: Do not leave the vacuum pump running unattended! Revision: Original Release 10/31/15 Vacuum bagged wings are quick to build, light weight,
More informationFlyingFoam Nurf. General Assembly Instructions
FlyingFoam Nurf General Assembly Instructions These instructions apply to the Nurf, an all EPP forward swept flying wing available from FlyingFoam.com. Building and operating a remote controlled aircraft
More information8-GUN CORVETTE ASSEMBLY INSTRUCTIONS
8-GUN CORVETTE ASSEMBLY INSTRUCTIONS THE HULL STEP 1 Fasten the Deck to the Hull. Find the hull. This is a large, pink, ship-shaped piece of insulating foam board. This will form the base of your model
More informationApplication & Care Reflexite V98 Conformable Graphic Sheeting For EMS Vehicle Graphic Applications RSA2340
Table of Contents General Information... 2 BEFORE APPLICATION... 2 STEP 1: TEMPLATING... 2 STEP 2: CUTTING... 2 STEP 3: SUBSTRATE PREPARATION... 3 STEP 4: SURFACE CLEANING... 3 STEP 5: APPLICATION TEMPERATURE...
More information275 RID Assembly Instructions
75 RID Assembly Instructions Part No. 0003003 v. Lscsep0 PARTS LIST (Specifications and contents subject to change without notice) Description Part # A. RID Track...0000050 B. Capacity Plate...0053 C.
More informationCricket carpets are usually installed over concrete or 'dynamic' (hard porous) bases.
Replacing/Repairing Cricket Carpets Cricket carpets are usually installed over concrete or 'dynamic' (hard porous) bases. Whilst some information on this page will apply to both types of base, where appropriate,
More informationPT 11 trouble-shooting and maintenance.
PT 11 trouble-shooting and maintenance. Does your rudder not stay down?...your back seat slip off?...your knobs tight and your leather pads loose? Maybe we can help. We have used our PT 11 s hard enough
More informationThe USA Canterbury J. Class Rules
Canterbury J Class Owners Association The USA Canterbury J Class Rules 2010 As Accepted 2008 and Revised February 2010 Published March 2010 The Canterbury J Class Rules ~ 2008 Page 1 of 10 THE CANTERBURY
More informationRaptor by Steve Childers
Raptor by Steve Childers Raptor Series Fighter This kite is somewhat difficult to build but well worth the effort. It's performance characteristics are, a good spin rate, excellent tracking, and wind window
More information$1 Fighter Kite. Here s how Manny made the conversion from an Eddy kite to a fighter kite.
6-2007 www.fighterkitecentral.com Manny Alves $1 Fighter Kite $1 Fighter Kite Manny Alves is one of the few masters of figher kite design and construction. Manny has a keen eye for fighter kites; and as
More informationLeafing Trees. A Clinic by Jeff Gerow. Spring TRAINing, Taunton, MA 2015
Leafing Trees A Clinic by Jeff Gerow Spring TRAINing, Taunton, MA 2015 This started when I was innocently purchasing new versions of leaves at the Scenic Express booth. Pete was standing next to me and
More informationShiel e d Kite t By B y Sam & Ca C rir King Ore r g e o g n o Kite t m e aker e rs s Retr t e r a e t t2013
Shield Kite By Sam & Cari King Oregon Kitemaker s Retreat 2013 SAIL ASSEMBLY Your pre-cut sail pieces include half-inch seam allowances. This provides enough material to complete a 1/4 inch double rolled
More informationCR 914 Class Rules. Revised July 15, 2000 See also CR-914 Class Rule Interpretations
CR 914 Class Rules Revised July 15, 2000 See also CR-914 Class Rule Interpretations 1 GENERAL - CLASS: The CR 914 is a One-Design class. The Class objective is that the sailing skills of the skipper shall
More informationPOMS Science Summer Challenge
POMS Science Summer Challenge The true essence of science is the relentless and unwavering need to know why. With your inquisitiveness, you can learn to do science. There are five basic skills you need
More informationA white sail for Edmond Dantes
A white sail for Edmond Dantes Making a new junk sail, then rigging and test-sailing it in the summer of 2012 Part one The construction of the sail..ed in June 2011... Edmond Dantes is a 9.47m /4-ton Mikkel
More informationTuning C420 Sails By Brian Doyle and Dave Kirkpatrick
Tuning C420 Sails By Brian Doyle and Dave Kirkpatrick In the spring of 2003, the Club 420 Class sails were redesigned to provide a better competitive and useful lifespan. Now that several events have been
More informationTube-on-tube to wire luff conversion by Rey Garza
Tube-on-tube to wire luff conversion by Rey Garza I recommend changing from the old tube-on-tube furling system to the wire luff system. I did it and I think that the boat is now easier to rig, plus I
More informationTable of content Introduction 5 1. Part 1. Assembly Tools needed for Assembly Glossary Hulls Mounting the beams 7
Table of content Introduction 5 1. Part 1. Assembly 6 1.1. Tools needed for Assembly 6 1.2. Glossary 6 1.3. Hulls 7 1.3.1. Mounting the beams 7 1.3.2. Fixing the mast rotation cleats 8 1.3.3. Placing the
More informationPerformance Cruising
Performance Cruising Performance Our definition of Performance portrays your total experience in dealing with Neil Pryde Sails. Every Neil Pryde sail is the result of a combination of craftsmanship, technology
More informationLoneStar Fiberglass Pools. Do-It-Yourself. Installation Manual
LoneStar Fiberglass Pools Do-It-Yourself Installation Manual Chris 1/3/2008 Do-It-Yourself The installation of a LoneStar Fiberglass pool is a much simpler task than most people think. What is important
More informationHADRON H2 CLASS RULES
HADRON H2 CLASS RULES 2018 The Hadron H2 was designed in 2015 by Keith Callaghan and is manufactured under licence by Hadron Dinghies Ltd. INDEX PART I ADMINISTRATION Section A General A.1 Language...
More informationHandle the film very carefully. As with aluminum foil, once creased, the film will remain creased.
RECOMMENDED TOOLS: Bottled water (not tap water) Spray bottle Squeegee or squeegee card Break-away utility knife (for cutting film) Single-edged razor blade (for cleaning glass) Ruler or tape measure Soft,
More informationModeling Asphalt Roads by Steve S. From a blog posting on Model Railroad Hobbyist
I've been working on a small mockup to test some ideas for asphalt and street trackage. I used 1mm black craft foam on code 100 track. You can go the full width of the rails and not interfere with the
More informationHow To Build A Water Rocket
How To Build A Water Rocket DESIGN AND DEVELOPMENT Brainstorm The first step in the design of a water bottle rocket is brainstorming. Brainstorming is a problem-solving technique that involves the spontaneous
More informationHow to Weather and Ballast Track
How to Weather and Ballast Track Presented by Jeffrey Jarr Weathering Track What is a train track comprised of? Weathering Track What does real weathered track look like? Weathering Track What does real
More informationThe Main Gaff... Main Gaff completed. Bearing block
Once the boom has been placed on the model, the topping lift needs to be rigged. It will be belayed to the port side cap rail. Use the eye bolt aft of the tackle we set up for the backstay. The topping
More informationApsara Hard chine version
Apsara Hard chine version Update of the RG65WIKI page. Introduction One often encounter people on forums looking for simple to build hard chine hulls. The RG65 class is ideal for initiation to remote controlled
More informationInstalling ST1300 Fairing Decals
Installing ST1300 Fairing Decals Caution: Decals are best applied when ambient air temperature is 60 degrees or higher. Do not apply in direct sunlight. Do not allow the decals to get wet while they are
More information1982 Hydrostream Viking Restoration
1982 Hydrostream Viking Restoration Part 2c: The Rebuild Daniel W. Rickey Winnipeg, Manitoba Canada daniel@cancercare.mb.ca 2000-09-22 Introduction Part one of this report showed how the shoddy manufacturing
More informationBladerider X8 Assembly Help Notes
2.1 Remove All Parts & Have Some Tools Handy Remove all items from the box and identify each part as per the packing sheet and check that nothing is missing. If there is something missing, please email
More informationNeil Pryde Sails International Design and Technical Office. O Day Sailboats Sails Overview
2002 Neil Pryde Sails International Design and Technical Office O Day Sailboats Sails Overview INTERNATIONAL DESIGN AND TECHNICAL OFFICE Product Overview Contact: Neil Pryde Sails Int. 354 Woodmont Road
More informationJ/22 Dave Perry. Based on sailing the POW in the Ft Worth Boat Club (TX) boats in 2006 We sailed with three in the boat
J/22 Dave Perry Based on sailing the POW in the Ft Worth Boat Club (TX) boats in 2006 We sailed with three in the boat GENERAL Boats spin fast! Boats go fast sideways when downspeed Use weight to help
More informationIOM RIGS AND SAILS CERTIFICATION CONTROL - CHECK LIST FORM 2017
INTERNATIONAL ONE METRE CLASS 2017 RIGS AND SAILS CERTIFICATION CONTROL - CHECK LIST FORM RIGS AND SAILS CONTROLLED 1 2 3 (circle, or cross out as appropriate) Hull Registration Number... Certification
More informationSTANDARD SPECIFICATIONS
STANDARD & OPTIONS SPECIFICATIONS January 2018 STANDARD SPECIFICATIONS TECHNICAL DATA Length: 5,55 m Width: 2,38 m Light displacement: 500 kg Mainsail area: 14,5 m2 Jib area: 9,2 m2 Gennaker area: 32 m2
More informationH ow To Buil d A Wa ter Rocket
H ow To Buil d A Wa ter Rocket DESIGN AND DEVELOPMENT Brainstorm The first step in the design of a water bottle rocket is brainstorming. Brainstorming is a problem-solving technique that involves the spontaneous
More informationSample Procurement Specifications for Aluminum Traffic Control Signs and Components
Sample Procurement Specifications for Aluminum Traffic Control Signs and Components These sample procurement Specifications were prepared by the American Traffic Safety Services Association (ATSSA) Sign
More informationDECAL APPLICATION INSTRUCTIONS
DECAL APPLICATION INSTRUCTIONS 1. Measure where you want your decal to be. Then tape in place on 1 side only to use as a hinge, using regular masking tape. Place your tape on the top, bottom or either
More informationHow To Make Gus Balls
How To Make Gus Balls A tutorial on making durable analogs for 2009 FRC Moon Rocks By Arthur Dutra III & Arthur Dutra IV 6 January, 2009 Wild Time Orbit Ball next to a finished Gus Ball FRC build season
More informationweber.cote Pool Paint
weber.cote Pool Paint weber.cote Pool Paint weber.cote Pool Paint is a cement-based, integrally coloured, waterproof finish, specifically formulated for the revamping of marble plastered pools. Applied
More informationAvery Dennison Instructional Bulletin 1.4 Application Methods for Pressure Sensitive Adhesive Films
Rev. 2 (April 2016) Avery Dennison Instructional Bulletin 1.4 Application Methods for Pressure Sensitive Adhesive Films Introduction Avery Dennison pressure sensitive adhesive films are available in a
More informationMiss Mayflower. Build Manual
Miss Mayflower Build Manual Thank you for the purchase of the Miss Mayflower, this new exciting craft will give you fun on many types of terrain including snow, gravel, pavement, grass, water, and when
More informationKUTIN BATTENS in SAILMAKING Inverness, 02. Feb / Ljubljana, 12. Nov. 2014
KUTIN BATTENS in SAILMAKING Inverness, 02. Feb. 2014 / Ljubljana, 12. Nov. 2014 Development of sails is unseparately connected with introduction of new materials for sailing boats, rigs and particularly
More information420 Rigging Guide.
A smaller version of the olympic 470 class, the 420 was formerly a youth development class. It has a good class following, and is a good introduction to performance boats. With a PY number of 1087 it s
More informationINTERNATIONAL ONE METRE CLASS
1 An official measurer shall carry out certification control by checking all items on the boat for compliance with the IOM class rule against the certification control - checklists for Hull & Appendages
More informationINTERNATIONAL. 49er CLASS RULES. The 49er Class was designed in 1995 by Julian Bethwaite and was adopted as an ISAF International Class in 1999.
INTERNATIONAL 49er CLASS RULES 2016 The 49er Class was designed in 1995 by Julian Bethwaite and was adopted as an ISAF International Class in 1999. INDEX PART I ADMINISTRATION Section A General A.1 Language...
More informationSailTrack Installation Instructions. CMPE Track
SailTrack Installation Instructions CMPE Track SH-500 SS SH-401 SS SH-200B SS SH-600 SS SH-200A SS www.tidesmarine.com This Tides Marine Sail Track System is used to attach a Tides Track to a bare carbon
More information49erFX CLASS RULES 2015
49erFX CLASS RULES 2015 49erFX Class Rules Page 1 INDEX PART I ADMINISTRATION Section A General A.1 Language... 4 A.2 Abbreviations... 4 A.3 Authorities & Responsibilities 4 A.4 Administration of the Class
More informationINTERNATIONAL. 29er CLASS RULES. The 29er Class was designed in 1997 by Julian Bethwaite and was adopted as an ISAF International Class in 2001.
INTERNATIONAL 29er CLASS RULES 2015 The 29er Class was designed in 1997 by Julian Bethwaite and was adopted as an ISAF International Class in 2001. INDEX PART I ADMINISTRATION Section A General A.1 Language...
More information