Brushbot Kit Instructions: Parts
|
|
- Shannon Wheeler
- 5 years ago
- Views:
Transcription
1 Brushbot Kit Instructions: Parts or AG13 Googly eyes Additional Tools Needed: Scissors or snips, hot glue gun or some type of glue suitable for plastic (epoxy or super glue should be fine).
2 Brushbot Kit Instructions: 1 Take a look at your : One side should have a lightly etched square and rectangle on it. This is the top of the chassis. Googly eyes Peel off one side of your double stick tape stripe and fit it inside the large rectangle. Grab your motor and center the spinny end over the smaller square. This square is the back of the chassis. 4) Make sure that your motor still spins freely, and press it down Pager Motor firmly into the tape. 5) Grab the blue wire from your motor, and twist the uninsulated section into a O or U shape. Press this down firmly into the tape.
3 Brushbot Kit Instructions: 2 Grab your zip tie, and use it to firmly secure your motor in place by wrapping it around the motor, through the two holes in the chassis. Googly eyes Zip ties only tighten in one direction: Insert the point end of the tie through the flat side of the opposite end. Tighten the zip tie and trim off any extra plastic.
4 Brushbot Kit Instructions: 3 Grab one of your batteries, and take a look at it: One side is completely flat, and has a + sign on it. Press this side down onto the stripped end of your blue motor wire firmly.googly eyes If you d like to give your bot some character, now is a good time! Thread your pipe cleaners (you can use more then one!) through the two holes on either side of the battery to make antennae.
5 Brushbot Kit Instructions: 4 Add some googly eyes to your bot, if you d like (and who doesn t???). Peel the paper backing off of the eyes to expose the adhesive, and press them onto your bot firmly.googly eyes Take the uninsulated end of the red wire, and twist it into an O shape. Press this O into the center of one of your dot stickers. The orange stickers work best if you re planning on doing some painting! If you find that your sticker is coming loose while using bot, just replace it with one Pageryour Motor of the extras in your kit.
6 Brushbot Kit Instructions: 5 Heat up your glue gun, (if you don t have one, any glue suitable for plastic will work), and get ready to glue on your brushes. eyes Take Googly a look at your brushes: They have slightly longer bristles at their pointiest end. This pointy, bristley end goes towards the back of the bot. Glue on your brushes, taking care not to burn yourself. Don t worry about centering them perfectly...different positions will give your bot different behaviors!
7 Brushbot Kit Instructions: 6 Press your dot sticker onto the top of the battery, and hold on as your bot comes to life! Googly eyes your motor doesn t turn If for any reason on, check to make sure that its wires are making firm contact with the battery. Also, be sure that the end of the red wire is only touching the inner most circle of the top of your battery. Play with your bot! Try moving the motor slightly to change it s behavior! 4) If you would like to paint with your bot, watercolors (liquid watercolors for the win) and heavy watercolor paper works best. Be sure to make a corral for your bot to keep on the paper: a cardboard box with it s bottom cut out should work fine!
ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS Ballpark Classics Baseball Game MLB Edition Figure B Read the instructions completely before beginning g assembly. You will need a Phillips screwdriver. 1. Remove the game from the
More informationPre-Paint>Fuselage>Empennage>Fit vertical tail fin. Objectives of this task: Materials and equipment required: Fit the spar extender
Pre-Paint>Fuselage>Empennage>Fit vertical tail fin Objectives of this task: To fit the vertical tail fin to the fuselage, including fitting the static probe, static tube, optional strobe light wiring and
More informationHow Scott Builds a Fighter Kite, May 2011 Updated Sept 2018
How Scott Builds a Fighter Kite, May 2011 Updated Sept 2018 MAKE A TEMPLATE 1. Draw half sail plan on 17x22 pad with 4x4 (1/4 inch) grid. Add ¼ inch extra on nose (for reinforcement) and plenty of extra
More informationTHE AMERICAN BARN DOOR KITE
THE AMERICAN BARN DOOR KITE Oregon Kitemaker s Retreat January 2007 Rod Beamguard 4104 NW 112 th Way Vancouver, WA 98685-3578 (360) 574-8050 home (360) 750-9833 office kytfevr@wa-net.com PLANFORM BARN
More informationGrandpa's Homemade Rocket for About a Dollar!
Grandpa's Homemade Rocket for About a Dollar! Grandpa and Granny Co. 2012 The most common items needed: (The number of Rocket parts from each item is before the parts name and its proportionate cost is
More informationWe hope you ll enjoy the Drifter as much as we have! Scott DeTray Model Aero Specifications:
We are excited to bring you the Drifter RC airboat. You re probably thinking it doesn t fly so what is Model Aero thinking??? We have always liked RC vehicles of all types and have had a fondness for airboats
More informationBelow are the instructions to build a roller-furling unit for under $10. Read the entire process before beginning the project.
Greg Cowens' $10 PVC Roller Reefing for CP-16's by Greg Cowen Below are the instructions to build a roller-furling unit for under $10. Read the entire process before beginning the project. Materials: 2
More informationManual 1: working with cutting films. MANUAL 1. Working with cutting films. March 2017
Manual 1: working with cutting films. MANUAL 1 R Working with cutting films March 2017 Manual 1: working with cutting films. R 1 NECESSARY TOOLS It goes without saying that you need the right tools if
More informationEaster Bunny Pompoms
Easter Bunny Pompoms When I was younger I remember it taking ages to make pompoms because of constantly passing a ball of yarn through the middle of two cardboard circles. Well this method makes it a lot
More informationSamurai Armor Set: Step by Step
Samurai Armor Set: Step by Step Pack 6 Stages -5 Contents Stage Pages 7-76 The tasset plates and shoulder pad Stage Pages 77-8 The tassets, helmet and helmet lining Stage Pages 8-86 The tasset plates and
More informationSCOUT PROP BUILDING INSTRUCTIONS & PHOTOS
SCOUT PROP BUILDING INSTRUCTIONS & PHOTOS Companies should be aware that tolerances in lengths of pipe and length of pipe inserted into joints can change the overall dimensions of product demonstration
More informationE. Test, and if needed, adjust tips of antenna. 1. Mark will test antennas with meter at ground end of feedline bundle. Will take 10 minutes.
Project Steps Overview: A. Prepare: B. Raise up small antenna. C. Raise up large antenna. D. Connect to new bundle of 4-feedlines pulled up from ground. E. Test, and if needed, adjust tips of large antenna.
More informationA Foundation Of Trust. Hanging By A Thread
Hanging By A Thread PROPS: Rope maker (See video at DoingWorks.com/movies.) 1 spool of cord for each team [I like to use 10 lb (4 kg test, 525 feet (160 meters) sisal cord] 1 spool of cord to use for demonstration
More informationMiniTwin by Acer
MiniTwin 250 - by Acer ASSEMBLY INSTRUCTIONS Thank you for choosing the MiniTwin 250 as your next project. This kit is easy to build and only requires a few hours to complete. Once finished, you will be
More informationWHITE WOLF. X-ray View MID POWER MODEL ROCKET KIT BUILDING INSTRUCTIONS KIT SPECIFICATIONS:
WHITEWOLF-38 PARTS LIST 1 - Nose Cone 1-17" Airframe 1-6" Motor Tube 3 - Aft Fins 3 - Forward Fins 2 - Centering Rings 1-15" Parachute 2 - launch lugs 1-12 Kevlar Shock Cord 1 - Motor Retention >>(screw/washer)
More informationNAVIGATOR PROP BUILDING INSTRUCTIONS & PHOTOS
NAVIGATOR PROP BUILDING INSTRUCTIONS & PHOTOS Science under the ice Ice sheet At regional competitions the ice is simulated by 8 ft x 4 ft ½-inch foam sheeting (Home Depot part #703990 [in store only],
More informationPitts Model 12 Wing Leading edge Installation
Pitts Model 12 Wing Leading edge Installation This procedure is used to install molded plywood leading edges included in the Pitts Model 12 kit. Nine (9) molded leading edge section are require per aircraft;
More informationHorizontal Fuselage. Top Vertical Fuselage 1. Lay out the Top Vertical Fuse Front(1), Top Vertical Fuse Back(2), and Vertical Stabilizer(3).
Rumbuilder 71 B-17 Congrats on your Rumbuilder B-17! We re glad you chose to fly with us! If you have any problems, or missing/broken kit pieces, please contact us. We d be happy to replace any damaged
More informationMake Your Own Bundled canes Revision Date: May 2014
Make Your Own Bundled canes Revision Date: May 2014 Attribution-ShareAlike 4.0 International (CC BY-SA 4.0) Summary: http://creativecommons.org/licenses/by-sa/4.0/ License: http://creativecommons.org/licenses/by-sa/4.0/
More informationModel Aero Sportster Indroduction
1 Model Aero Sportster Indroduction We are excited to introduce the Model Aero Sportster! Inspired by classic designs of the past, the Sportster is a relaxing slow flyer, equally at home indoors or outside
More informationFly Tying Tips from Hermann Fisher, Kamloops, Canada As Submitted by Lee Ann Ross
Fly Tying Tips from Hermann Fisher, Kamloops, Canada As Submitted by Lee Ann Ross How to deal with a crowded head when tying flies: Use a piece of a bicycle inner tube and punch small holes in it. Slip
More informationInstructions for Fun Foam Critter 4/25/2007 BP Hobbies LLC 140 Ethel Road W Suite J Piscataway NJ,
Instructions for Fun Foam Critter 4/25/2007 BP Hobbies LLC 140 Ethel Road W Suite J Piscataway NJ, 08854 http://www.bphobbies.com Specifications: Wing Span: 20" Length: 20" Flying Weight: 5.5-7.0 oz Controls:
More informationWasp size 2-4. Copyright J:sonSweden AB. Rec. hook Size 10/12
Wasp size 2-4 Please watch the videos before choosing a specific fly pattern, they explain how to use Detached body pins, Wingburners and Wingmaterials. And how to tie in Wings/Wing-buds and Nymph-legs/Nymph-backs.
More informationAssembly Instructions. -Cantilever Boat Lifts
Assembly Instructions -Cantilever Boat Lifts Winch Instruction Page Safety Information 1. The winch is built for the multipurpose of hauling and lifting operations. It is not to be used as a hoist for
More informationTugster. Tug Boat. Competition or Sport Tug Kit. A Zippkits R/C Boat. Building Instructions
Z I P P M A N U FA C T U R I N G Tugster Tug Boat Competition or Sport Tug Kit A Zippkits R/C Boat Building Instructions 2016 JMP Hobby Group St. Paul, Indiana 47272 www.zippkits.com Toll Free (866) 922-ZIPP
More informationSTEP 1 A. Lay the two Motor Mount Tubes on a flat surface with ends even and Glue them together with White Glue. Allow Glue to set before moving on.
Prod. No. A51003 Skill Level Three QUEST AEROSPACE, INC PO Box 2409 Pagosa Springs, CO 81147 800-858-7302 Things You ll Need To Assemble this Kit: Pencil and Hobby Knife: White Glue: Aliphatic Resin glue,
More informationMotion Commotion. KindergarTen-second. Matter and Energy TEKS. Vocabulary
Motion Commotion KindergarTen-second Matter and Energy TEKS Kindergarten: K.6B, K.6C, K.6D First Grade: 1.6B, 1.6C, 1.6D Second Grade: 2.6B, 2.6C, 2.6D Vocabulary above, attract, back and forth, behind,
More informationLectric Cycles Mid-Drive Electric Motor Installation
Lectric Cycles Mid-Drive Electric Motor Installation This write-up describes the installation of a Lectric Cycles electric motor. The model is the e-rad Mid-Drive 750 Watt conversion kit, installed on
More informationAliphatic Resin Wood Glue. 18" Fabric Parachute Part #PNC50 Part # Part #11700 Part #J0016. Launch Lug
ADANCED * What you will need to build the Quest High-Q Hobby Knife * Straight Edge Pencil Aliphatic Resin Wood Sanding Sealer & Brush Spray Paint Parts and exploded view of the Quest High-Q Nose Cone 18"
More informationBuild Your Own Electromagnet
Build Your Own Electromagnet Stuff you need: 9-volt battery Insulated copper wire with ends stripped Large iron nail Small paper clips or staples Wrap the copper wire tightly around the nail and touch
More informationGeneral Build Instructions for Mach 1 BT50 and BT55 Single Fin Kits. Needed Items for Assembly
General Build Instructions for Mach 1 BT50 and BT55 Single Fin Kits 60-80 grit sandpaper Hobby knife Tape measure Scissors CA Super glue 30-minute epoxy 5-minute epoxy Masking tape 1/16 drill bit Needed
More informationNEXT GENERATION FLEX FENCE
NEXT GENERATION FLEX FENCE Area To Be Fenced.. With Next Generation Flex Fence any post that is not in a straight line with another post must be braced. Layout your fence installation. Determine all end
More informationSamurai Armor Set: Step by Step
Samurai Armor Set: Step by Step Pack 3 Stages 9-12 1 Contents Stage 9 Pages 29-31 The cuirass side and tassets Stage 10 Pages 32-37 The shoulder plate and tassets Stage 11 Pages 39-41 The shoulder plate
More informationSPOOLER INSTRUCTIONS. STEP 12 If you are going to paint your posts, that should be done at this time.
STEP 4 Starting where you marked the end post location, move down your fence line 6 feet and make another mark. This mark is where your second upright post will be installed. Continuing down the fence
More informationTECH SHEET ORANGE PIVOT TOOL INSTRUCTIONS
page 1 ORANGE PIVOT TOOL INSTRUCTIONS This is a guide of how to change the pivot bearings on an Orange frame with a bore style pivot axle. 4 8 Bore Type Pivot Axle Horiz-Hold Type Pivot Axle Please read
More informationBMW Motorrad. Installation Instructions. BMW Motorrad Communications System for Schuberth C3
BMW Motorrad Installation Instructions BMW Motorrad Communications System for Schuberth C3 Order No. 01 29 2 219 831 BMW Motorrad 05/2011 Be sure to read these instructions carefully and completely before
More informationHow Do I Install My Garden Master Bucket Garden?
How Do I Install My Garden Master Bucket Garden? 1. On the arrival of your Bucket Garden open the bucket and remove the 4 screws from the outside of the bucket rim and pull the 2 buckets apart. Check the
More informationKayaking Bob s Tandem Island SpraySkirt Kit Installation Instructions
Kayaking Bob s Tandem Island SpraySkirt Kit Installation Instructions Copyright 2011 by R. E. & D. L. Conlon Kit Contains: Right & Left SpraySkirts 3 Long Black Wire Ties* 3 Short Black Wire Ties* 1 3/16
More informationItem # in-1 Swivel Table. Inch BILLIARDS AIR HOCKEY TABLE TENNIS
Item # 45-6066 3-in-1 Swivel Table 3 BILLIARDS AIR HOCKEY TABLE TENNIS 84 Inch Limited 90-Day Triumph Sports USA, Inc. Warranty All Triumph Sports USA, Inc. (TSU) games have a limited 90-day from date
More informationMayfly Dun size 1-3. Use the TyinGuides, they will help you get the correct proportions.
Mayfly Dun size 1-3 Please watch the videos before choosing a specific fly pattern, they explain how to use Detached body pins, Wingburners and Wingmaterials. And how to tie in Wings/Wing-buds and Nymph-legs/Nymph-backs.
More informationCongratulations, once again, on buying an E RIDER Model 18!!!!
Congratulations, once again, on buying an E RIDER Model 18!!!! USER MANUAL We are sure you will be excited by the delivery of your brand new bike and you will be eager to start using your E RIDER as soon
More informationFISH NET REPAIR. By Alfred Carlson
FISH NET REPAIR By Alfred Carlson 2 Contents 1. Contents 2 2. 3-Spot Repair (One Broken mesh) 3 3. V-Shaped Repair (Two Broken meshes ) 23 4. N-Shaped Repair (Three Broken meshes) 33 5. M-Shaped Repair
More information*Heart* Pom-pom rug. 1, 2, 3... go! Zweigart & Sawitzki GmbH & Co. KG Fronäckerstraße Sindelfingen. - more than 3 hours -
Pom-pom rug *Heart* - more than 3 hours - 1, 2, 3... go! Zweigart & Sawitzki GmbH & Co. KG Fronäckerstraße 50 71063 Sindelfingen Preparation: Arrange the material you need. The Zweigart Twist canvas (Item
More informationMounting the RoboFocus RF-3 Unit on the LX-200/400 MicroFocuser
Mounting the RoboFocus RF-3 Unit on the LX-200/400 MicroFocuser The RoboFocus unit can be mounted on the Meade MicroFocuser, commonly found on the LX-200/400 series. The RF folks point to this URL as a
More informationMoving On Kentucky Bluegrass High School Robotics Competition. Sponsored by Western Kentucky University Department of Engineering
Moving On 2015 Kentucky Bluegrass High School Robotics Competition Sponsored by Western Kentucky University Department of Engineering Kickoff Meeting: September 11, 2015 Competition Day: November 7, 2015
More informationModel Aero AT-6 Texan Introduction
1 Model Aero AT-6 Texan Introduction We are excited to introduce the Model Aero AT-6 Texan! Originally used as an advanced trainer by the U.S. Armed Forces, the AT-6 is a relaxing slow flyer, equally at
More informationHOW-TO: Install a Wildcat Lighting System
Items needed: Acetone Isopropyl Alcohol Power Drill 8 zip ties Marine Goop 9/6 Drill Bit /6 Drill Bit Pencil or dry erase marker Measuring tape Extra wire Extra Grey Wire nuts Wire cutters Wire Strippers
More informationFin Shape Science Experiment Kit
Kit #00524 Fin Shape Science Experiment Kit Test Different Fin Shapes to Find Out Which One Performs the Best! P/N Description Qty 10079 AT-18/5.4 (Fin Shape Sci Eng. Mount Tube) 1 10118 AT-33/3 (Payload
More informationAGM 33 PIKE ALL FIBERGLASS. Specifications Length: 92 Diameter 5.5 Weight: 24 lbs Motor Mount: 75mm Fins: 6-3/16 G10 CP: 68 from nose tip Parts List
ALL FIBERGLASS AGM 33 PIKE Specifications Length: 92 Diameter 5.5 Weight: 24 lbs Motor Mount: 75mm Fins: 6-3/16 G10 CP: 68 from nose tip Parts List (1) Filament Wound Nose Cone w/ Metal Tip (1) Nose Cone
More informationInstallation Guide, MPower Echelon Console
Installation Guide, MPower Echelon Console AC Performance, AC Sport and AC Performance Plus Schwinn Echelon Console (External Routing) 1. Install batteries to console. Mount the console to the bike. 2.
More informationDrawn up by: / RK Revision: 01 Reviewed: Page: 1 of 23 HI-SR 540 USA. Operating instruction SR 540 Face Shield
Page: 1 of 23 Operating instruction SR 540 Face Shield Page: 2 of 23 General information The SR 540 Face Shield can be used together with the SR 500 Powered Air-Purifying Respirator system of components
More informationBuilding a Rocket (Advanced) Before you build a rocket try the bottle on the launcher to test if it holds pressure and fits correctly.
You Will Need 3X 2ltr Bottles 1X Paper lip 1X Glue/Double Sided Tape 1X ardboard 1X Bin Liner 1X Roll of Fishing Line or Thin s Sheets of Paper Side A of Fin 1X Hot Glue Gun 1X Pair of Scissors 1X Fine
More informationRANGER PROP BUILDING INSTRUCTIONS & PHOTOS
RANGER PROP BUILDING INSTRUCTIONS & PHOTOS Science under the ice Ice sheet At the international competition, the science under the ice product demonstration will take place under an actual sheet of ice.
More informationMANTEL BIKE BOX: PACKING YOUR ROAD BIKE FOR TRANSPORT
MANTEL BIKE BOX: PACKING YOUR ROAD BIKE FOR TRANSPORT ROAD BIKE COMPONENTS 1 Frame: a b c d e Top tube Down tube Seat tube Chain stay Seat stay 2 Saddle 3 Seat post 4 Seat post clamp 5 Rear brake 6 Front
More informationBubbles Sheets Learn Curriculum
Bubbles Sheets 1 2 3 Learn Curriculum Bubbles Theme Worksheets Letters H & S Numbers 1 2-3 - 4 Shape Circle Color Blue Color Green Monday Tuesday Wednesday Thursday Friday Copyright, 1 2 3 Learn Curriculum,
More informationStevenson Projects Building the Hull Top Deck and Bulkheads
Stevenson Projects Building the Hull 1. Print out both piece sheets. 2. Cut out one keel piece and glue it to a piece of balsa wood or dense cardboard. Cut out the second keel piece and glue it to the
More information3 Scotch-Weld Polyurethane Reactive Adhesive Applicator Replacement Part Installation Guide
3 Scotch-Weld Polyurethane Reactive Adhesive Applicator Replacement Part Installation Guide Description: AIR SUPPLY LINE KIT Product ID/Stock No.: 62-9895-0005-3 For use with: 3M Scotch-Weld Polyurethane
More informationpompom ANIMALS MAKE Instructions for making birds, butterflies, ladybugs, and hedgehogs. Pompoms
pompom MAKE ANIMALS Instructions for making birds, butterflies, ladybugs, and hedgehogs. Pompoms Contents 02 H ow to Make Pompoms Using Pompom Makers 06 H ow to Make Semicircular Pompoms Using Pompom Makers
More informationBUILD A BETTER BUBBLE BLOWER
Grades K 2, 3 5 20 60 minutes BUILD A BETTER BUBBLE BLOWER DESIGN CHALLENGE Design, build, and test a successful bubble blower. MATERIALS Supplies and Equipment: Shallow bowls or trays Scissors Towels
More informationHillbilly Golf. Included. Game Building Instructions. 2-foot Fence Building Instructions. Bolo making Instructions
Hillbilly Golf Game Building Instructions Included 2-foot Fence Building Instructions Bolo making Instructions Minus Bar Building Instructions and Minus bar play rules Plus some Extras! Hillbilly Golf
More information175 m2 (1,880 sq ft) Kit
175 m2 (1,880 sq ft) Kit Your Kit Components 1 x 50m 2 Complete Kit Tap Assembly 5 x Auto-flushing valve (spinlock) 2 x 50m 2 Extension Kit 3 x Straight joiner (spinlock) 4 x Tee joiner (spinlock) 1 x
More information#59114 Rola 2-Bike Rack Carrier (Shown Assembled) (A) (C) (B)
Use for Parts: #59114 Rola -Bike Rack System #59115 Rola 1-Bike Add-On TOOLS REQUIRED 10mm or 13/3 Socket & Wrench #59114 Rola -Bike Rack Carrier (Shown Assembled) Tray Attachment Hardware: (3) Plastic
More informationItem # in1 Rotating Table. Inch BILLIARDS AIR HOCKEY TABLE TENNIS
Item # 45-6066 3-in1 Rotating Table 3 BILLIARDS AIR HOCKEY TABLE TENNIS 84 Inch ! WARNING: Rotating game should be done under adult supervision. Rotating table may cause a pinching hazard for young children
More informationNAVIGATOR Product demonstration prop building instructions
NAVIGATOR Product demonstration prop building instructions Regional competitions may build product demonstration props out of materials other than PVC pipe. Your regional coordinator will inform you of
More informationFeaturing Coats Dual Duty XP. Supplies
Halloween Black Cat Basket Technique: Designed By: Skill Level: Crafting Time: Finished size: Sewing, Fabric Crafting Linda Turner Griepentrog Intermediate An evening 6" (15.24cm) (at base) x 3 1 2" x
More informationAdding Sculpted Toes to a Cloth Doll Foot
Adding Sculpted Toes to a Cloth Doll Foot by Sherralyn St. Clair, www.sherralynsdolls.com Many cloth doll patterns leave the doll's foot as a simple rounded shape. I have found that adding sculpted toes
More informationA Table Top Wind Tunnel You Can Build
A Table Top Wind Tunnel You Can Build Basic principles of aerodynamics can be studied in the classroom with this simple, inexpensive wind tunnel. All you need to build it is some cardboard boxes, glue,
More informationBuild Your Own Electromagnet
Build Your Own Electromagnet 9-volt battery Insulated copper wire with ends stripped Large iron nail Small paper clips or staples Wrap the copper wire tightly around the nail and touch the ends of the
More informationVacuum Bagging Wings Instruction Manual Purdue University
Vacuum Bagging Wings Instruction Manual Purdue University Note: Do not leave the vacuum pump running unattended! Revision: Original Release 10/31/15 Vacuum bagged wings are quick to build, light weight,
More informationHOME ASSEMBLY INSTRUCTIONS
HOME ASSEMBLY INSTRUCTIONS This Papillionaire Bicycle now belongs to you. It will take you to work, wait patiently outside your local cafe, and carry your groceries home. This is the start of your long-term
More informationTripod Setup Guide (M-TPx)
Items needed: 1/2 inch wrench, mast level (M-MLA), medium size wire cutters, crescent wrench, all-purpose grease, tape measure, tie wraps, redi-mix cement (optional), shovel (optional), sledge hammer (for
More informationBladerider X8 Assembly Help Notes
2.1 Remove All Parts & Have Some Tools Handy Remove all items from the box and identify each part as per the packing sheet and check that nothing is missing. If there is something missing, please email
More informationE-trike Li Assembly Guide
PREPARATION 1. Read this assembly manual BEFORE commencing assembly. 2. Carefully remove all the components and packaged hardware from the shipping boxes. 3. Unpack the contents of the large double box
More informationUMBILICAL CORD MODEL FOR UMBILICAL VEIN CATHETERIZATION TRAINING
UMBILICAL CORD MODEL FOR UMBILICAL VEIN CATHETERIZATION TRAINING A Guide to its Construction and Usage INTRODUCTION Introduction This training model aims to familiarize clinicians with umbilical vein catheterization
More informationAny tool, at the ready. 3M DBI-SALA Fall Protection for Tools Pocket Reference Guide
Any tool, at the ready 3M DBI-SALA Fall Protection for Tools Pocket Reference Guide 3M DBI-SALA Fall Protection for Tools Product Catalog Download/Request a Printed Catalog Download the product catalog
More informationPOSITIVE SAFETY LOCK KIT INSTALLATION GUIDE
POSITIVE SAFETY LOCK KIT INSTALLATION GUIDE The Positive Safety Lock Kit for the TASER X2 and X26P conducted electrical weapons (CEWs) was created to provide an enhanced safety location mechanism for customers
More informationRudder Kit Assembly Instructions for Quest 13
Rudder Kit Assembly Instructions for Quest 13 Revised 4/2/2015 78501 Rudder System The Hobie Quest is designed for the addition of an optional rudder system. Rudder systems in boats like this allow you
More informationIn each step, the needed parts are shown the number right below. Locate all parts for the step.
Tools Required for Assembly Phillips Screwdriver, Med Needle Nose Pliers Sandpaper (#400 grit) Hobby Knife Scissors CA Instant Glue Rubbing Alcohol Drill Bit 1/16", 1.6mm 5/64, 2mm 1/8, 3mm 5/32, 4mm Before
More informationINSTALLING AN INEXPENSIVE AIR LINE TO MEASURE WATER DEPTHS IN WELLS
INSTALLING AN INEXPENSIVE AIR LINE TO MEASURE WATER DEPTHS IN WELLS Joe Henggeler Extension Agricultural Engineer-Irrigation An inexpensive, yet highly accurate, device to measure the depth to water in
More informationKaZoon. Kite Kit. User Guide. Cautionary and Warning Statements
KaZoon Kite Kit User Guide Cautionary and Warning Statements 56799 V0717 This kit is designed and intended for educational purposes only. Use only under the direct supervision of an adult who has read
More informationBuild Your Own Flamethrower Step-by-step Manual
Build Your Own Flamethrower Step-by-step Manual Table of Contents: Parts List.. page 1 Operation...page 6 Diagrams. pages 7-9 Parts list: Required: Air tank (large) Pressure washer gun with high-pressure
More informationHandle the film very carefully. As with aluminum foil, once creased, the film will remain creased.
RECOMMENDED TOOLS: Bottled water (not tap water) Spray bottle Squeegee or squeegee card Break-away utility knife (for cutting film) Single-edged razor blade (for cleaning glass) Ruler or tape measure Soft,
More informationYour kit contains the following items. Additional Items You May Need. Pre- cut parts Propeller rigging and rubber Sandpaper Covering sheet
Your kit contains the following items Pre- cut parts Propeller rigging and rubber Sandpaper Covering sheet The SkyFox offers great glide performance in a rubber powered plane due to its built up wing.
More informationCopyright Velocomp LLP 2006
ibike Pro Cadence Handlebar Mount Owners Manual January 2007 1 Table of Contents Installing the ibike Pro cadence mount on your bicycle Installing the ibike Pro cadence mount on your time trial bike Installing
More informationBackCountry ebikes 2019 MULE Assembly
BackCountry ebikes 2019 MULE Assembly Required Tools: Cutting Pliers (to cut box poly strapping and heavy bike banding) Scissors (to remove bubble wrap) Allen wrenches (3mm, 4mm, 5mm, 6mm) Wrenches (10mm,
More informationOWNER S MANUAL AirTop Large and AirTop Small
It is the owner s responsibility to read and understand the material presented in this manual and to instruct all users or operators on how to use product safely. By inflating the product, you hereby agree
More informationwww.aquaglidekayak.com WORK SPACE AND TOOLS 1. Take care to position yourself in a clean, dry area with good ventilation. For proper curing of adhesives, temperature should remain above 10 C (50 F).
More informationCan you find 5 differences between the two scenes below?
SPOT THE DIFFERENCES Can you find 5 differences between the two scenes below? ANSWERS: 1-Fire in background. 2- Dusty name missing. 3-Dusty s propeller missing. 4-Lil Dipper s smile. 5-Windlifter enters
More informationMethylethycetone (MEC) - PMS 60 polyurethane glue - Grease - White silicone
CHAPTER PLAN page : 1/8 SAILING BOAT SUSPENDED WITHOUT DECK BEARING SAILING BOAT SUSPENDED WITH DECK BEARING SAILING BOAT SUSPENDED WITH AUTOMATIC BEARING ALIGNMENT RUDDER SYSTEM FOR ANTARES MOTOR BOAT
More informationSAFETY WARNING. WARNING.
EXPERIMENT MANUAL 1ST EDITION 2014 2014 THAMES & KOSMOS, LLC, PROVIDENCE, RI, USA THAMES & KOSMOS IS A REGISTERED TRADEMARK OF THAMES & KOSMOS, LLC. PROTECTED BY LAW. ALL RIGHTS RESERVED. WE RESERVE THE
More informationHow to Wind a Great Bobbin
Projects on the H O R I Z O N Issue 4 How to Wind a Great Bobbin Bobbins that are loosely wound, like the one shown above, can create stitch problems. They also run out much sooner, because they arenʼt
More informationShiel e d Kite t By B y Sam & Ca C rir King Ore r g e o g n o Kite t m e aker e rs s Retr t e r a e t t2013
Shield Kite By Sam & Cari King Oregon Kitemaker s Retreat 2013 SAIL ASSEMBLY Your pre-cut sail pieces include half-inch seam allowances. This provides enough material to complete a 1/4 inch double rolled
More information2 pcs. 1pc. 4 pcs. 4 pcs. 4 pcs. 4 pcs.
Quoizel, Inc. 6 Corporate Parkway Goose Creek, SC Customer Service Phone 63.273.2700 Fax 63.23.702 www.quoizel. Assembly Instruction Sheet #IS-KLT860C For Style KLT860C ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wire
More informationASSEMBLY MANUAL HOBIE CATSY
ASSEMBLY MANUAL HOBIE CATSY HOBIE CAT EUROPE ZI Toulon Est, BP 50 8078 Toulon cedex 9, France Tel : + (0)9 08 78 78 - Fax : + (0)9 08 99 Email : hobiecat@hobie-cat.net - http://www.hobie-cat.net ASSEMBLY
More informationWELLS JOHNSON HIGH VOLUME CANISTERS
WELLS JOHNSON HIGH VOLUME CANISTERS USER MANUAL DISASSEMBLY OF HARVESTING CANISTERS Please follow the instructions provided to disassemble 5L, 3L, 2L, and 1L, 250mL and 500mL harvesting canisters. 1. Unscrew
More informationQRPGuys Single Lever Mini Paddle
QRPGuys Single Lever Mini Paddle First, familiarize yourself with the parts and check for all the components. If a part is missing, please contact us and we will send one. You must use qrpguys.parts@gmail.com
More informationwww.allsportsystems.com Page 1 of 29 Page 2 of 29 Table of Contents Items You Supply: 4 MICROBAY Setup Instructions 5 Items Provided By AllSportSystems: 5 MEASURING AND CUTTING THE 1 EMT POLES FOR THE
More informationThank you for purchasing your new Empire Reloader B Sound-Activated 3-Speed Paintball Hopper!
Thank you for purchasing your new Empire Reloader B Sound-Activated 3-Speed Paintball Hopper! Should you require any technical assistance on the use of this product, or if your product needs servicing,
More information2 pcs. 1pc. 3 pcs. 3 pcs. 1pc. 3 pcs.
Quoizel, Inc. 6 Corporate Parkway Goose Creek, SC Customer Service Phone 6.27.2700 Fax 6.2.702 www.quoizel. Assembly Instruction Sheet #IS-KLT860C For Style KLT860C ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wire
More informationQUALITY ALUMINUM BOAT LIFTS, INC. INSTRUCTIONS. Dominator Lake Lift
INSTRUCTIONS Dominator Lake Lift PHONE:251-986-3882 * FAX:251-986-3136 QABLDOMINATORINST.2014 P a g e 1 Quality Aluminum Boat Lifts, INC. Installation Instructions: Dominator Lake Lift Thank you for your
More information