PLANING TECHNIQUES ...
|
|
- Elmer Sims
- 5 years ago
- Views:
Transcription
1 Atuned block plane with a sharp blade in the hands of an experienced Rodmaker is a precision instrument. The sound it makes as it quickly cuts through a bamboo strip producing a long tight curled shaving is truly music to the ear. It stirs the soul of a Rodmaker. FIGURE 1. A finely tune plane and the shaving it produces. Planing is a skill that must be mastered and practiced so that you get to this level. There are many subtle aspects of planing that the beginner misses. Not only must you produce the pretty curl but you must maintain the angles on the bamboo strip you are planing. At times this may appear difficult to the beginner. The key to planing good angles is having a strategy and method for planing bamboo strips that enables the rodmaker to maintain control of the planing process. In this section we will discuss the strategies and methods for maintaining control of the process of planing bamboo strips to final dimensions. I will review latter some of these techniques in the sections concerning use of the 1st, 2nd, and Final planing forms that pertains directly to that step of rodmaking. The Beginners Supplement to The Maters Guides to Bamboo Rodmaking 1-1
2 Basic Techniques BASIC TECHNIQUES.. Setting the Plane Blade Review the anatomy of a plane. Refer to the section on tuning you plane before going further. Holding the Plane Simple as it sounds, there is a technique for correctly setting the plane blade and adjusting for depth of cut. Try this method for consistant results: Back the depth setting wheel down from where you last used it. Place the blade in the plane and tighten down. This should be firm not locked in. The blade must be able to move to adjust it. First visually make sure the blade is in square. The cutting edge should be parallel with the mouth opening of the sole of the plane. This is a simple adjustment with the adjustment lever. Insure that the blade is retracted far enough back so it does not cut. A simple test is to place the plane on a strip and try to plane. If it does not cut, this is good. If does cut, then back the blade out with the adjustment wheel. The reason we want the blade back when we first set it in is that there is slop in the blade adjustment. If you put it in at a cutting depth then it may slip back during planing. Or the first cut may be way too deep. What we do now is rotate the depth setting wheel until the blade first starts to cut. This should produce not even a curl yet since it barely touches the bamboo strip. Now you can incrementally turn the wheel about a ¼ turn and test it to see how much it cuts. An experienced rodmaker can look at the curl and tell you exactly how much is being taken off. This is easy to do with a little bit of practice. Get in the habit to mic the curl you produce with the dial caliper to see how thick the curl is. You will soon become familiar with seeing a curl and knowing what depth of cut produces that type of curl. Normally the tighter curl the smaller the cut. You will soon realize that the finest cut usually takes off between.002 and.003. While a medium cut takes about.005, and a heavy cut takes Anything more than that is living dangerously with your strip. There are several basic things in holding the plane and using it. Which plane you use is a personal choice. The two most popular planes are the Stanley and Record. The 9 and ½ models are the preferred choice of most rodmakers. I personally use the Record. The The Beginner s Supplement To the Masters Guides to Bamboo Rodmaking 1-2
3 Planing Strips Techniques reason is that it just fits my hand better. The plane is cradled rather than held. When it is sharp, all you should do is push and guide it rather than grabbing it and exerting pressure downwards. The weight of the plane is enough. The heal of the plane rests in the palm of the hand. The thumb and 4th finger steadies it and the fore finger rests on the tab in front. The plane should feel comfortable in this position. The thumb and 4th finger exert enough pressure to steady the plane and keep it horizontal with the form. Planing Position The plane is positioned at an angle or skewed to the strip to be planed. It is not perpendicular to the strip. This is slices the strip and results in a nice curl of shavings coming off at an angle. It is easier for the blade to cut at and angle then directly perpendicular to the strip. The angle of attack is about 20 degrees, just enough to make a big difference. At this angle you can still cradle the plane and steady it. Remember, you are pushing the plane and do need undue force to make the cut. Planing Basics Several basic-planing principles will help you plane better. First never reach. If you start planing and the strip is long, just walk your way down the strip. Reaching is a basic mistake. At the end of a reach, you are beyond the point where you have good control of the plane being horizontal to the form and it has a tendency to roll to the direction you are standing on. A second problem is that you may not clear the end of the strip before bringing the plane back and the strip catches as you come back and bad things happen to the strip. PLANING STRIPS TECHNIQUES.. Rough Strips - 1st and 2nd Forms With rough strips you have a technique to allow you to quickly mill the strip to get to your angle. This technique is required on when using your 1st and 2nd forms. Plane the end of the strip away from you until your are down to the angle. You will have planed the final or so. Stop and turn the strip around and then plane into the rough strip from the back. This has several advantages. First you are not planing into the area that you have planed to the angle, thus avoiding planing too deep into that part of the strip. Second you can plane quickly into the rough portion of the strip easily. Lastly you will have much better control of the strip because you can secure it with your fingers right behind the planing area on the good surface. The Beginner s Supplement to the Masters Guides to Bamboo Rodmaking 1-3
4 Planing Tips Final Strips When planing strips after they have the angles in your final form, start forward at the top 12 or so and make a clean pass. Then move back 6 and make you next pass(s) until you get a clean pass. Then move back again working your way back to the butt. Each time making a clean pass down the strip. This technique allows you to get clean straight sides in your strips with out dips and valleys. Once you made clean pass down the entire strip and ready to flip the strip, use your center gauge and check the angles every 5 down the strip. If the angles are off, place the strip back in the form, adjust the tilt of the plane and make another pass down the entire strip. Do not just plane the area where the angle is off. This causes an uneven edge on the strip. This promotes glue lines showing in the rod. If the angles are good then flip the strip and plane the other side. When finished - check the angles. Don t put it aside until the angles are correct. PLANING TIPS.. The best tips I can give you are: Let the plane do the work don t ever apply pressure to plane Keep the plane horizontal to the form Don t ever reach Keep the plane position at an angle to the form. Sharpen, Sharpen, Sharpen - never use a dull blade - see section on sharpening for knowing when to sharpen. PLANING SAFETY.. It is not that planing strips is dangerous. It is planing strips with a dull blade can cause the plane to grab and move the strip. That is not a problem by itself. It is the position of your fingers that is the problem. The planed edge of a bamboo strip is sharp, very sharp. It will cut your finger in a heartbeat. Never put your fingers on the edge of a strip. Always hold the flat portion of the strip. Rubber finger guards do help protect your fingers. But the best protection is a sharp blade and correct position of the fingers. The Beginner s Supplement To the Masters Guides to Bamboo Rodmaking 1-4
5 Summary SUMMARY.. Planing is a skill developed through practice. To be good at planing strips you need to have control of the process. The above techniques will help you gain that control. Like all aspects of rodmaking it requires time and patience. The moment you hurry or get impatient Murphy s Law will apply. The Beginner s Supplement to the Masters Guides to Bamboo Rodmaking 1-5
6 Summary The Beginner s Supplement To the Masters Guides to Bamboo Rodmaking 1-6
T H E M O S T I M P O R T A N T L E S S O N O F A L L
T H E M O S T I M P O R T A N T L E S S O N O F A L L #2 The Grip CHEAT SHEET 1. Minimal compensation for consistency 2. Grip rotation influences club face angle 3. Turn hand right for more hook, Turn
More informationTHE GARRISON BINDER ...
Did you ever wonder why (to quote Andy Rooney) the Garrison binder is for many rodmakers the source of contentious problems while other rodmakers never seem to have problems. One of the primary reasons
More informationBasic Rowing Technique
COMPETITIVE ROWING BALANCE ROWING STROKE TIMING & SPEED CATCH DRIVE FINISH RECOVERY 1 BASIC ROWING TECHNIQUE The rower s aim is to: a> produce the highest physiological performance and b> transform this
More informationA Low Cost Digital Angle Gage, version 3
A Low Cost Digital Angle Gage, version 3 By R. G. Sparber Copyleft protects this document. 1 Sometimes re-inventing the wheel has advantages. What you see here is just a variation on a sine bar. The accuracy
More informationMETROLOGY LAB. I DEVICES BASED ON VERNIER SCALE
METROLOGY LAB. I DEVICES BASED ON VERNIER SCALE Indirect Measurement; two balls 2 Lab6: Roundness Test 12/1/2017 Indirect Measurement; four balls 3 Lab6: Roundness Test 12/1/2017 Angle measurement using
More informationMisaligned Folds Paper Feed Problems Double Feeds Won t Feed FLYER Won t Run iii
Operator s Manual Table of Contents Operator Safety... 1 Introduction... 2 Unpacking and Setup... 3 Unpacking... 3 Setup... 4 FLYER Overview... 5 FLYER Diagram... 5 Capabilities... 5 Control Panel... 6
More informationProduct Overview: Key Features:
APGL4 Model Tripod Product Overview: The Ravelli APGL4 is a Professional Quality Tripod providing a solid base for high-end photographic equipment. This model is all pressure treated aluminum alloy construction
More informationLESSON 14: THE SABER AND THE SCABBARD
LESSON 14: THE SABER AND THE SCABBARD cant guard pistol belt port saber scabbard PURPOSE This lesson introduces you to the manual of arms for the saber. After you have mastered these procedures, you will
More informationEvaluation: 1. Can participants on a regular basis cast with a spin-casting reel with little effort 2. Can participants get close to a target.
Spin-casting Sharon Rushton- Best Time: This lesson can be taught as the first lesson on casting. Depending on the age group and time you have available, you may want to start with the Can-Casting Lesson,
More informationThe following lesson is excerpted from
The following lesson is excerpted from A Fresh Approach to the Snare Drum is the most comprehensive method available that simultaneously provides instruction for rhythm reading, technique fundamentals,
More informationINSTRUCTION MANUAL OF THE STRINGWAY CROSS STRINGING TOOLS.
INSTRUCTION MANUAL OF THE STRINGWAY CROSS STRINGING TOOLS. 1. PERSONAL ADVISE: The Stringway cross stringing tools are designed to do a rather smart job. They are designed to be very user-friendly and
More informationDRILLS MANUAL & SELF CORRECTION SYSTEM
DRILLS MANUAL & SELF CORRECTION SYSTEM Symple Swing "The Easy-To-Learn Golf Swing " From Simple Golf LLC Support@SimpleGolf.com Website: www.simplegolf.com Copyright 2005 Simple Golf LLC Symple Swing Drills
More informationThanks for shopping with Improvements! 20 Reel Mower with Catcher Item #
Thanks for shopping with Improvements! 20 Reel Mower with Catcher Item # 411837 To order, call 1-800-642-2112 West Chester, OH 45069 0313 If you have any questions regarding this product, call 1-800-642-2112
More informationThe Saber and the Scabbard. Key Terms. cant guard pistol belt port saber scabbard. Execute the manual of arms with the saber and the scabbard
Lesson 8 The Saber and the Scabbard Chapter 5 Key Terms cant guard pistol belt port saber scabbard What You Will Learn to Do Execute the manual of arms with the saber and the scabbard Linked Core Abilities
More information2990 Lorne Scots Royal Canadian Army Cadet Corps Rifle Drill
2990 Lorne Scots Royal Canadian Army Cadet Corps Rifle Drill Page 1 of 27 TABLE OF CONTENTS PARA ITEM PAGE Section 1 BASIC RIFLE DRILL 1.1 INTRODUCTION 3 1.2 ATTENTION 5 1.3 STAND AT EASE FROM ATTENTION
More informationRIFLE DRILL. 1. General. Before commencing instruction in rifle drill, it is important that the cadets receive instruction in the parts of the rifle.
RIFLE DRILL 1. General. Before commencing instruction in rifle drill, it is important that the cadets receive instruction in the parts of the rifle. 2. Rifle Movements. Unless stated otherwise, cadets
More information632 AccuPro Set-up & Operation
632 AccuPro Set-up & Operation Always check: Reel & Roller bearings Bent or broken blades Make sure the reel spins freely in the frame Place the Reel Into the Machine There are three lifting options for
More informationFISH NET REPAIR. By Alfred Carlson
FISH NET REPAIR By Alfred Carlson 2 Contents 1. Contents 2 2. 3-Spot Repair (One Broken mesh) 3 3. V-Shaped Repair (Two Broken meshes ) 23 4. N-Shaped Repair (Three Broken meshes) 33 5. M-Shaped Repair
More informationFinal Assembly Instructions Bikes with Quill Stems
Final Assembly Instructions Bikes with Quill Stems Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our expert
More informationPro Bow. .com. the construction. one using to use the. video. The. with. We would. love to hear others. Figure 1
Pro Bow The Hand www.probowthehand..com Instructions for Small Hand 1 Ribbon Congratulations on your purchase of Pro Bow The Hand. This item truly revolutionizes the construction of bows. Never before
More informationReblitz Upright Regulation List - With Comments By Mark Cerisano, RPT, B.Sc.(Mech.Eng.)
Reblitz Upright Regulation List - With Comments By Mark Cerisano, RPT, B.Sc.(Mech.Eng.) Reblitz steps in bold. My comments in regular font. 1. Position the let-off rail. Should read something like Check
More informationThe BIG BOOK of Golf Drills
The BIG BOOK of Golf Drills 1 How to Use This Guide Congratulations on purchasing the Big Book of Golf Drills! This book is designed to use as a reference guide. We do not recommend printing this out as
More informationMASTER TRUING STAND TS-3. Optional Dial indicator set with brackets Dial indicator bracket set only
MASTER TRUING STAND TS-3 3 2 1 3 8 9 4 10 7 6 5 12 13 Optional 1555-1 Dial indicator set with brackets 1556-1 Dial indicator bracket set only 49 11 16 14 15 48 32 31 37 38 20 19 17 18 34 39 21 36 22 33
More informationNorth Sails Seattle Thunderbird Tuning Guide
Page 1 of 6 North Sails Seattle Thunderbird Tuning Guide Introduction The following tuning guide is meant as a good starting point in setting up your boat. Since not all Thunderbirds are exactly alike
More informationKey Terms. balance barrel bolt butt hand guard muzzle port arms sling stacking swivel stock trail arms trigger guard
Lesson 7 Stationary Movements with the M-1 Rifle Chapter 5 Key Terms balance barrel bolt butt hand guard muzzle port arms sling stacking swivel stock trail arms trigger guard What You Will Learn to Do
More informationTechniques To Treat Your Pain At Home (512)
Techniques To Treat Your Pain At Home (512) 288-5322 7010 W. TX-71 Suite 360 Austin TX, 78735 Arm Only Bird Dog Start in the quadruped position (all fours) with arms and thighs perpendicular to the floor.
More informationRATLINER Assembly Instructions.
Model Shipways Inc. www.modelexpo-online.com RATLINER Assembly Instructions. Patent Pending 1. Remove center stands and braces from the main rigging frame. 2. The Stands and Braces should press release
More informationINSTRUCTIONS FOR GLUING ON THE BUMPER FOR PORT TOWNSEND WATERCRAFT S NESTING DINGIES. (Or requires a 1 surface to adhere to.)
INSTRUCTIONS FOR GLUING ON THE BUMPER FOR PORT TOWNSEND WATERCRAFT S NESTING DINGIES. (Or requires a 1 surface to adhere to.) The PT 11 bumper is made from a high quality, non marking EPDM rubber. This
More informationSwing Your Partner. by Beth Hester. GH Productions, Inc. The Basket Maker's Catalog
Swing Your Partner by Beth Hester GH Productions, Inc. The Basket Maker's Catalog Materials are available from your basketry supply store or contact: The Basket Maker's Catalog GH Productions, Inc. 521
More informationArms Drills. This chapter contains rifle drills that are commonly used in parades. As far as possible, they are laid out in the order of priority.
Arms Drills Contents 1. Introduction 9. Marching with the Rifle 2. Parts of a Rifle 10. Saluting with the Rifle on the March 3. Attention, Stand at Ease and Stand Easy 4. Pledge Taking Advanced Arms Drills
More informationBeginners Fly-Tying Notes
Beginners Fly-Tying Notes SESSION 1 Tools Bobbin holder Threader (for dental floss!) Bodkin/ Dubbing needle (hat pins!) Vice 1 Check that: the jaws hold the sizes of hooks you want to tie on; and the stem
More informationOptimist Tuning Guide
Optimist Tuning Guide Sail Care: To help you re new racing sail stay in top condition as long as possible here is some tips - Try not to crease your sail, some creases can cause MIT tears in your sail
More informationInstructions for using the PRECISION DIGITAL PITCH GAUGE 2008, Precision Analytical Instruments, Inc. Congratulations!
10857 Millington Court Blue Ash, OH 45242 513-984-1600 (voice), 513-984-4090 (fax) email Doug@ToolsForAnalysis.com Instructions for using the PRECISION DIGITAL PITCH GAUGE 2008, Precision Analytical Instruments,
More informationLevel 2 Online Course
Level 2 Online Course One for all. Skill School Lesson 2: Throwing US Lacrosse Lesson 2: Throwing Introduction Level 1 emphasized coaching the proper mechanics of a good overhand throw or pass. In this
More informationGRIP LOCK CHOCK (GLC)
GRIP LOCK CHOCK (GLC) JANUARY 2012 NOMENCLATURE GENERAL CONCEPT An eight (8) Chock System comprised of four (4) Left Hand and four (4 ) Right Hand Chocks. The Main Body of the chock is black The Left Hand
More informationLESSON 7: THE PRONE POSITION
LESSON 7: THE PRONE POSITION PURPOSE This lesson introduces you to the correct technique for firing in the prone position. INTRODUCTION prone sling The prone position has the lowest center of gravity and
More informationTeachings From An American Style Fighter Kite
Teachings From An American Style Fighter Kite When flying a fighter kite, one of my goals is to adjust the kite so its flight characteristics match, as close as possible, the way I want the kite to fly.
More informationBEGINNING GOALKEEPING
BEGINNING GOALKEEPING January 2010 Page 1 Page 2 January 2010 INTRODUCTION When many young players see the equipment a goalkeeper has to wear and they say to themselves Wow I want to be a goalkeeper. But
More informationBasketball Shooting Form
Basketball Shooting Form Shooting Form A shot can be a mysterious thing. What feels great one day feels terrible the next. Consistency comes with practice and solid shooting form. Shooting form is also
More informationBuild This World Record Fuselage Model
Build This World Record Fuselage Model Here You Have Complete Instructions and Plans to Build a Plane of Sure-fire Performance that Established a World Record at the 1932 National Airplane Model Competition
More informationWarnings: Notes: Revised: January 8,
OAI Model 204IR Mask Aligner Standard Operating Procedure Faculty Supervisor: Prof. Robert White, Mechanical Engineering (x72210) Safety Office: Peter Nowak x73246 (Just dial this directly on any campus
More informationrobart HOW-TO Series Model Incidence Meter
robart HOW-TO Series Model Incidence Meter The term incidence is something of a misnomer since this highly versatile tool is capable of measuring or comparing angles other than incidence of a wing or tail.
More informationSERIES 2 RAMP OWNER S MANUAL TOOLS REQUIRED: BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup.
SERIES 2 RAMP OWNER S MANUAL BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup. Use caution and care for your back when lifting, pushing, pulling, folding or unfolding
More informationStarts & Turns. Vejen September 3 rd, 2016
Starts & Turns Vejen September 3 rd, 2016 Start Position Rear leg: angle 90 degrees in knee Foot full on wedge with toes touching the horizontal platform. Wedge distance depending on the 90 degree take-off
More informationINFLATOR TDUX-IT-16 AND GAS CYLINDER E
INFLATOR TDUX-IT-16 AND GAS CYLINDER E7512-0160 Operating manual Inflator TDUX-IT-16 together with the special gas cylinder E7512-0160 is specifically designed for inflating TDUX duct seals. The inflator
More informationHOW TO CATCH - THE RIGHT WAY
The next few pages will show you some tips on improving your technique, by practicing these at every opportunity, they will eventually become part of your natural game. Not only will they help you to improve
More informationHOW TO HOLD THE SHOT
HOW TO HOLD THE SHOT Balance the shot in his hand so it is resting at the point where the fingers are connected to the palm of the hand. Keep their fingers together and allow their thumb to gently rest
More informationIntroduction to Evolutionary Hoof Care s New Hoof Care Work Stations TM and Evo Hoof Stands TM Also see Video Instructions at
Introduction to Evolutionary Hoof Care s New Hoof Care Work Stations TM and Evo Hoof Stands TM Also see Video Instructions at www.evohoofcare.com This new generation of hoof support devices will significantly
More informationTUNE YOUR SAILS SPEED. Optimist Tuning Guide. Photo Wavelength
TUNE YOUR SAILS FOR OUTRIGHT SPEED Photo Wavelength PEAK / HEAD THROAT TACK CLEW THANK YOU for choosing North Sails for your Optimist. Whether you are just starting out in an Optimist you are an experienced
More informationLESSON 12: STATIONARY MOVEMENTS WITH THE M-1903 RIFLE
LESSON 12: STATIONARY MOVEMENTS WITH THE M-1903 RIFLE PURPOSE balance barrel bolt port arms sight sling sling swivel stacking swivel This lesson introduces the procedures for executing the manual of arms
More informationHot Tapping Machine. OPERATIONS MANUAL and OPERATING INSTRUCTIONS
262-2040 Hot Tapping Machine For performing 1/4 6 Hot taps 285 psi or less. Municipal Water, Sewage, & Building Services Use OPERATIONS MANUAL and OPERATING INSTRUCTIONS WARNING: These instructions are
More informationFive Key Concepts for Goaltending Hockey Canada s Approach Skating The Goalie Stance (Athletic position) Stick Grip...
s Level 1 Goaltending TABLE OF CONTENTS INTRODUCTION Five Key Concepts for Goaltending... 1 Hockey Canada s Approach... 2 Skating... 3 The Goalie Stance (Athletic position)... 3 Stick Grip... 4 Skating
More informationCaliber Sled Wheels Assembly Instructions for PN and 13579
Caliber Sled Wheels Assembly Instructions for PN 13576 and 13579 Caution: Read all instructions before assembling or using Sled Wheels. Follow the steps in order. Only use Sled Wheels as intended, following
More informationOptimist Tuning Guide
Optimist Tuning Guide Prepared by, Andrew Wills of North Sails New Zealand, World Champion Coach and Sailor. One of the most important items, in terms of speed, for any sailing vessel, are the shape and
More informationThe Simple Swing
The Simple 1-2-3 Swing The Amazing "1-2-3 Swing" Guarantees The Average Golfer Can Break 90 In Less Than a Week! The Amazing "1-2-3 Swing" Guarantees Average Golfers Can Learn To Consistently Hit The Ball
More informationCoach & Goaltenders GOALTENDER BASICS
Coach & Goaltenders GOALTENDER BASICS STANCE To maximize net coverage and ability to move while maintaining balance. Body Position: Feet Little more than shoulder s width apart, slight ankle bend with
More informationFX IMPACT OWNER S MANUAL
made in sweden FX IMPACT OWNER S MANUAL Warranty Information All FX Airguns carry a One Year Warranty against faulty workmanship and defective materials. If it becomes necessary, first contact the dealer
More informationGrandmaster Dr. Ted Gambordella
The Complete Book of Wrist Locks By Grandmaster Dr. Ted Gambordella Everything you need to know about Wrist Locks. By Grandmaster Dr. Ted Gambordella 1 I have always loved to do wrist locks since I first
More informationLab #21 - ORR: Resonance Tube
Chapter 21 Lab #21 - ORR: Resonance Tube Introduction The vertical resonance apparatus is a device for helping the Physics student understand the principle of waves and resonance. In particular the study
More informationRIPPLE TANK - with rippler & kit
GENERAL DESCRIPTION: RIPPLE TANK - with rippler & kit Cat: SW3430-001 with illuminator, rippler & kit. The ripple tank is used to investigate wave motion in a shallow trough of water to understand how
More informationUNITED STATES MARINE CORPS
UNITED STATES MARINE CORPS INTERSERVICE NONLETHAL INDIVIDUAL WEAPONS INSTRUCTOR COURSE MARINE CORPS DETACHMENT 686 Minnesota Ave Fort Leonard Wood, Missouri 65473 STUDENT OUTLINE Train the Application
More information"RIGGING SAFETY IN CONSTRUCTION ENVIRONMENTS"
PRESENTER'S GUIDE "RIGGING SAFETY IN CONSTRUCTION ENVIRONMENTS" Part of the "CONSTRUCTION SAFETY KIT" Series Quality Safety and Health Products, for Today...and Tomorrow OUTLINE OF MAJOR PROGRAM POINTS
More informationCHAPTER 4 ADVANCED GROUND-FIGHTING TECHNIQUES
(FM 21-150) CHAPTER 4 ADVANCED GROUND-FIGHTING TECHNIQUES After achieving an understanding of the basics of ground fighting, other elements of fighting on the ground are added. These techniques, however,
More information2019 AUDITION PACKET CYMBALS. Pacific Crest Youth Arts Organization PO Box 5409 Diamond Bar, CA
2019 AUDITION PACKET CYMBALS Pacific Crest Youth Arts Organization PO Box 5409 Diamond Bar, CA 91765 www.pacific-crest.org Welcome to the 2019 edition of Pacific Crest. We ve assembled a group of excellent
More informationLESSON 13: STATIONARY MOVEMENTS WITH THE M1 RIFLE
LESSON 13: STATIONARY MOVEMENTS WITH THE M1 RIFLE PURPOSE balance fall in parade rest port arms trail arms upper band (Note: Since there are many similarities between the manual of arms for the M1 and
More informationHitting The Driver Made Easy
Table of Contents Introduction 3 Equipment 4 The Golf Shaft 4 The Golf Grip 5 The Club Head 6 Equipment Summary 7 The Setup And Swing 9 The Grip 10 Ball Position 12 Alignment 12 Posture 14 The Take-Away
More informationPhysics in Tang Soo Do Jack Sanders-Reed, Ph.D.
Physics in Tang Soo Do Jack Sanders-Reed, Ph.D. Basic Concepts In order to inflict damage on an opponent, or to break something, we must deliver energy to the target, the more energy, the more damage.
More informationMADILL 24.7" 365 TILT SET-UP PROCEDURE WITH REXROTH VALVE ON MACHINE
MADILL 24.7" 365 TILT SET-UP PROCEDURE WITH REXROTH VALVE ON MACHINE MADILL 24.7" SAW - 365 DEG. TILT-REXROTH VALVE DANGER DO NOT perform any adjustment on sawhead unless saw blade lock bolt and guard
More informationMHBYW Dynasty Program
MHBYW Dynasty Program Level 3: Red Skill Properly Executed? Comment Staggered/Square Stance Yes No Motion Yes No Starting Positions Neutral Yes No Top Yes No Bottom Yes No Four Defensive Stops Yes No Head,
More informationDance With Janet Instructor Training
Lesson 7 Triple Steps & Turns A. A. Triple Steps Triple steps are three steps in two beats of music. You will be stepping on the downbeat as well as the upbeat, and the count is 1&2, 3&4, etc. This means
More informationBasket for Janice. by Beth Hester. GH Productions, Inc. The Basket Maker s Catalog
Basket for Janice by Beth Hester GH Productions, Inc. The Basket Maker s Catalog Materials are available from your basketry supply store or contact: The Basket Maker s Catalog GH Productions, Inc. 521
More informationTry it! You ll like it!
083016 1 Lashing is a method used to join together poles (or spars as they are often called) with rope to build camp projects like wash stands, tables, and even a camp shower! Knowing how to attach two
More informationThanks for downloading this free report / checklist that contains the short version of the 7 Steps To Correct Serve Technique.
Thanks for downloading this free report / checklist that contains the short version of the 7 Steps To Correct Serve Technique. It s a quick reminder on WHAT are the key steps in building the serve and
More informationFront Cover Picture Mark Rasmussen - Fotolia.com
Flight Maneuvers And Stick and Rudder Skills A complete learn to fly handbook by one of aviation s most knowledgeable and experienced flight instructors Front Cover Picture Mark Rasmussen - Fotolia.com
More informationSailboat Rigging and Tuning
Sailboat Rigging and Tuning February 13, 2006 The following texts are compiled from three main sources, Bob Sterne (www.crya.ca), Greg Fisher (www.modelyacht.org), and the Soling 1M website (www.solingonemeter.org).
More informationShooting Clinic, Alaska Biathlon Anchorage 4 April 2009 Instructor: Richard Barlow Session 3: Fundamentals, Position Details A.
Shooting Clinic, Alaska Biathlon Anchorage 4 April 2009 Instructor: Richard Barlow Session 3: Fundamentals, Position Details A. Fundamental Steps 1. The sequence of six steps for a well-aimed shot needs
More informationFinal Assembly Instructions Bikes with Threaded Headsets
Final Assembly Instructions Bikes with Threaded Headsets Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our
More informationHow to tune a Djembe. 1 P a g e
How to tune a Djembe Look at rope pairs here. I always cross the ropes that almost touch as the pass through the same loop of the bottom cradle as pairs for the first row. It does very little tightening,
More informationIt is also possible to make a more traditional version of the design - which I call Easy Glider - which can be launched by hand in the normal way.
The Kendal Flyer Designed by David Mitchell The Kendal Flyer is a rubber band launched plane that I designed in 1990. It is possible to make a pure origami version but I prefer this one in which the nose
More informationOPERATING INSTRUCTIONS FOR THE MODEL 85B
OPERATING INSTRUCTIONS FOR THE MODEL 85B SAFETY PRECAUTIONS FOR THE MODEL 85B System Under Pressure: Shut off air supply and disconnect air hose before disassembling or disconnecting parts. Flying Debris:
More informationUPWIND Light wind: <8 knots Sail Setting
UPWIND Since the Laser is a strictly one designed class with very few controls, upwind sailing becomes very physical and technical. Big efforts will only result in little gains in your upwind speed. However,
More information(Specification changes are highlighted in yellow)
APPENDIX II SCRUTINEERING (Specification changes are highlighted in yellow) 101. ICF Canoe Polo Kayak Manufacturers Scheme 1.1. - After January 1 st 2015 - All new composite canoe polo kayaks manufactured
More informationCONSTRUCTOPEDIA NXT Kit 9797
CONSTRUCTOPEDIA NXT Kit 9797 Beta Version 2.0 August 17, 2007 Center for Engineering Educational Outreach Tufts University Table of Contents Simple Shapes and Structures. Page 3 Ways To Attach NXT Motors...
More informationThe Secrets Of The Swing
The Secrets Of The Swing brought to you by www.golfclubdistance.org and Amazing Golf Mind Table of Contents 1. The Address 2. The Take Away 3. The Top Of The Backswing 4. The First Move 5. The Downswing
More informationThe Golf Grip Instruction Manual
The Golf Grip Instruction Manual This manual is an overview of how to Hold the golf club. How we Hold the club is commonly referred to as our Grip. There is another use for the word Grip in golf and this
More informationLearn to Hydrofoil. The. Easy steps for you to progress from your first ride on a hydrofoil to your first jumps off the water.
The Learn to Hydrofoil Easy steps for you to progress from your first ride on a hydrofoil to your first jumps off the water. To find a nearby USA Water Ski GrassRoots event, go to: www. 1 Level 1 Hydrofoil
More informationMake Your Own Bundled canes Revision Date: May 2014
Make Your Own Bundled canes Revision Date: May 2014 Attribution-ShareAlike 4.0 International (CC BY-SA 4.0) Summary: http://creativecommons.org/licenses/by-sa/4.0/ License: http://creativecommons.org/licenses/by-sa/4.0/
More informationU.S. Shooting Team Balance, Strength and Stability Workout. Shooting Warm-Up
U.S. Shooting Team Balance, Strength and Stability Workout Shooting Warm-Up Modified by Dan Durben and Sommer Wood from the program originally developed by Amber Darland for the USA Shooting National Rifle
More information(Club Two-Step, NC2S) Richard Powers
Nightclub Two-Step (Club Two-Step, NC2S) Richard Powers Buddy Schwimmer developed this dance in the late 1970s and it has become widely popular among American social dancers. It is the perfect dance for
More informationA basic look at bamboo fly rod tapers
A basic look at bamboo fly rod tapers Lots of things can have an impact on the performance of a bamboo fly rod. The quality of the cane, the type of glue used, flaming or heat treating, all make some difference.
More informationSkills and Drills The Center's Skills
Introduction to Offensive Fundamental Skills Skills and Drills This section reviews the fundamental skills of flag football, explains why each is important and emphasizes the skill s basic teaching points.
More informationFoam Plate Glider: Sonic Silhouette
Designed by: Ritchie Kinmont Project #40 Page 1/25 Foam Plate Glider: Sonic Silhouette About this project: The Foam Plate Glider Sonic Silhouette is the first in a series of flying glider projects made
More informationStructure (Down plane)
By Lauren Russell Structure (Down plane) The body (toes, knees, hips, wrists and shoulders) is aligned parallel to the intended target line. The torso is tilted over the ball from the hips whilst maintaining
More informationThrower s Maintenance Program
Thrower s Maintenance Program Elbow at 90 and fixed at side. Pull out with arm keeping elbow at side Elbow at 90 and fixed at side. Pull arm into body keeping elbow at side. Shoulder at 90 and elbow at
More informationTable of Contents. Snare Book Pg. 4 Tenor Book Pg. 21 Bass Book Pg. 38 Cymbal Book Pg Section Leaders
1 2 Table of Contents Snare Book Pg. 4 Tenor Book Pg. 21 Bass Book Pg. 38 Cymbal Book Pg. 56 2017 Section Leaders Lauren Hulit (307) 399-1282 Joe Wojciechowski (303) 817-1461 Micah Iribarren (307) 287-4212
More informationc01.qxd 4/17/02 8:53 AM Page 5 Getting in the Zone Starting Right
c01.qxd 4/17/02 8:53 AM Page 5 1 Getting in the Zone Starting Right 5 c01.qxd 4/17/02 8:53 AM Page 6 You may not realize it, but your muscles are not the most important part of your body when you are doing
More informationCarolina Trace Country Club
Carolina Trace Country Club Short Game School Michael Krick Head Golf Professional Trace Member Table Of Contents Putting 1, 2 Putting Evaluation Matrix 3 Putting Positions 4 Chipping 5, 6 Pitching 7,
More informationNEW EMPLOYEE ERGONOMIC WORKSHEET
NEW EMPLOYEE ERGONOMIC WORKSHEET DIRECTIONS New Employee: This document has been prepared to assist you and your supervisor in determining some of the items that you may need. After you have had an opportunity
More informationGRAPPLING CONCEPTS LESSON 23: T.R.I.G
GRAPPLING CONCEPTS LESSON 23: T.R.I.G Most of the other concepts we've covered in this course have been principles which help you, kick butt on the mats right away. Learn them today and use them tomorrow.
More information