Progressive Safety Services LLC
|
|
- Homer Greer
- 5 years ago
- Views:
Transcription
1
2
3 Guarding Floor and Wall Openings and Holes Powered Platforms, Manlifts and Vehicle Mounted Work Platforms Fall Protection Duty to Have Fall Protection Fall Protection Systems and Criteria Training Requirements
4 Must be protected from free falling six feet or more: Maintenance Activities Railcar Prep Use of Boom Articulating Lifts Others???
5
6 Evaluate the workplace for fall hazards and plan accordingly. Focus on: Structural integrity issues. The presence of fall hazards Situations where fall arrest or restraint will be difficult to utilize. Types of fall arrest or restraint methods to be used. Protection for persons working under or passing below overhead work. Highly recommend a physical inspection of the facility.
7 Eliminating the Hazard
8 Eliminates the hazard all together. 4 foot (General Industry) fall protection railings, etc.
9 Top-rails must be 42 inches above the walking/working surface. Mid-rails 21 inches. Must be capable of withstanding 200 lbs. of force.
10 All excavations should be marked with caution tape, reflective pylons, traffic cones, etc. Excavations six feet or greater must be protected by a guardrail, fence, barricade or properly rated cover.
11 Use railings or other means to guard: Open Stairways Chute Floor Opening Pits Trenches
12 Preventing Fall Related Injuries
13 Rigged so that an employee can neither free fall or make contact with a lower level. Bring an employee to a complete stop and limit deceleration distance to 3.5 feet.
14 Anchorage Harness Connectors
15 Activates upon a fall Stops Fall Prevent serious injury
16 Distance a body falls before the fall arrest system activates. Must not exceed 6 feet or contact w/lower level or obstruction.
17 Secure Point. Must withstand forces associated with fall arrest. Support 5000 lbs. per person. Preferably above to eliminate swing fall hazards.
18 Disperses forces of fall arrest over the chest, thighs, pelvis and shoulders. Safely support body upright until rescued. Connected to anchorage by a lanyard. D-Ring on back is for fall arrest, side is for positioning/restraint.
19 Shock absorbing Self retracting lifelines (SRL). All must have double action locking hooks w/tensile strength of 5000 lbs.
20 Do not connect two snap hooks together (roll out). The D-ring should always be larger than the snap hook connected to it. Be aware of sharp edges. Guard sharp edges with a protective materials.
21 Full Body Harness D-Ring Anchorage Connector (Lanyard)
22 Personal fall arrest systems must limit arresting forces to 1800 lbs. when used with a full body harness. Shock absorbing mechanisms should be used for fall arrest.
23 Free Fall Distance = 6 ft + Deceleration Distance = 3.5 ft = Total Fall Distance = 9.5 ft + Height of the Worker = 6 ft + Safety Factor = 3 ft = Required Clearance = 18.5 ft Assume: 6 foot shock absorbing lanyard anchored above the head.
24 Travel Freely Automatically locks to arrest a fall Example: Rope Grab
25 More than one person attached Rated for correct number of persons.
26 Safety cage must be chained to forklift Safety cage must have a properly rated anchorage point Person in cage must attach to anchor point with a lanyard attached to full body harness Person in cage must wear a hardhat It is not safe to move forklift while in person(s) are in the cage.
27 Crane Basket Required Boom Articulating Lift Required Scissor Lifts Not required unless railing is removed. Scaffolding Not required unless railings are not being utilized (10 ft)
28 A tie off system that restrains the employee from falling. Must limit employee free fall to 2 feet. Often utilizes the side D-rings. Side D-rings are not be used for fall arrest.
29 Focus on hardware, webbing, labels, stitching and indicators. Before each use inspect lanyards, SRL and harnesses: Cuts Frays Damage Cracks Burns Annually by a competent person.
30 Personal fall protection systems and components subjected to impact loading need to be taken out of service until: Inspected by a competent person Determined to be undamaged and suitable for use If equipment is not useable, make it unusable.
31 Clean full body harness with water and mild soap solution. Do not use bleach or bleach solutions. Air Dry Store full body harness in a cool, dry, clean environment, out of direct sunlight. Many factors can damage a harness: Chemicals Extreme heat Sunlight
32
33 Employer shall provide prompt rescue of employees in the event of a fall or ensure that employees are able to rescue themselves. In-house Equipment Local First Responders
34 Train employees on: Nature of hazards in the work area. The correct procedures for maintaining, erecting and inspecting fall protection systems Document all training: Name of employee trained Date Signature of person who conducted the training
35 Required when: Changes in the workplace. Changes in the types of fall protection systems or equipment used. Determined that the employee does not have requisite understanding or skills.
36
37
38 Estimated 500,000 people treated for ladder injuries each year. Estimated 300 people die per year from ladder related falls, electrocutions, etc.
39 3 Point Rule -Always Maintain 3 Point Contact. Face Ladder Hands Must be Free Hoist Tools Rather Than Carrying (tool bags).
40 1 in 5 injuries using portable ladders can be attributed to defects. Should be inspected before use and taken out of service for defects: Feet/Legs intact No broken or missing rungs No broken hardware spreaders Other causes of injuries: Improper selection Contact with electrical power lines Climbing ladder with tools/materials in hand(s)
41 Type Type 1AA Special Duty (Rugged Professional) Type 1A Extra Heavy Duty Type 1- Heavy Duty Industrial Type II Medium Duty (Painter/Handyman) Type III Light Duty (Household Use) Duty Rating (combined weight) 375 lbs. 300 lbs. 250 lbs. 250 lbs. 200 lbs.
42 Find level surface Use 4 to 1 Rule For every 4 feet of climb the base of ladder should be positioned 1 foot out. Ladder must be positioned 3 feet above landings Tie off top of ladder Never lean out Foot the ladder
43 Firm Level Surface Lock Spreaders Stay off top two steps Keep away from doorways or traffic
44
45
46
47
48
49
workplace fatalities involving falls to a lower level. Fall related fatalities make up 16% of workplace fatalities
2013 574 workplace fatalities involving falls to a lower level Fall related fatalities make up 16% of workplace fatalities Bureau of Labor Statistics Passive Fall Prevention Fall Arrest Fall Restraint
More informationFall Protection 4/7/16
Fall Protection 4/7/16 Passive Fall Prevention Fall Restraint Fall Arrest Inspection/Maintenance 1910.23 Guarding Floor and Wall Openings and Holes 1910.66 Powered Platforms, Manlifts and Vehicle Mounted
More informationFall Protection ABC s
Fall Protection ABC s Chris Caron American Safety & Supply, Inc. Fall Protection ABC Itinerary Review types of fall arrest systems Review and discuss ladder safety Discuss the various components of fall
More informationToday s Discussion. Passive Fall Prevention. Fall Restraint. Fall Arrest. Ladders PROGRESSIVE SAFETY SERVICES LLC 2019
Today s Discussion Passive Fall Prevention Fall Restraint Fall Arrest Ladders PROGRESSIVE SAFETY SERVICES LLC 2019 2 Fall Related Incidents Approximately 20% of workplace fatalities; disabling injuries,
More informationSection 16B. Fall Protection. Falls are the second leading cause of death in the workplace. Factors contributing to falling incidents:
Section 16B. Fall Protection Falls are the second leading cause of death in the workplace. Factors contributing to falling incidents: 1. Personal factors Lack of concentration. Use of medication. Poor
More informationFall Protection Checklist. Guardrail System
Fall Protection Checklist Location/Department: Date of Inspection: Inspectors: Corrective Actions: Work order/memos were issued: Yes No Date issued: In accordance with the MIOSHA and OSHA standards the
More information8. Fall Protection Procedures WAC
1.0 Fall Protection Introduction 8. Fall Protection Procedures WAC 296-155-245 If an employee is exposed to a fall hazard of ten (10) feet or more in height, the employee must use a fall restraint, fall
More informationARKANSAS TECH UNIVERSITY FACILITIES MANAGMENT HEALTH AND SAFETY MANUAL
FALL PROTECTION (PERSONAL FALL ARREST SYSTEMS) 15.0 The purpose of this policy is to specify procedures and training for the safety of the employees in the Facilities Management Group while working on
More informationFall Protection. Fall Speed vs. Reaction Time. Good body reaction time = 0.5 seconds Travel distance in 0.5 seconds = 4 feet (1.21mts.
Fall Protection Fall Speed vs. Reaction Time Good body reaction time = 0.5 seconds Travel distance in 0.5 seconds = 4 feet (1.21mts.) In 1 second your body will fall 16 feet (4.8 mts.) By the time you
More informationFall Speed vs. Reaction Time
Fall Protection Fall Speed vs. Reaction Time Good body reaction time = 0.5 seconds Travel distance in 0.5 seconds = 4 feet (1.21mts.) In 1 second your body will fall 16 feet (4.8 mts.) By the time you
More informationFALL PROTECTION WORK PLAN (Alstom Power Installation Canada)
FALL PROTECTION WORK PLAN (Alstom Power Installation Canada) Location: Unit: Foreman: Task: Supervisors Ensure: Workers must review and sign this fall protection work plan prior to starting work in an
More informationDoc No: FPP CARDINAL SURVEYS COMPANY. Safety Management System. Initial Revision Date: Version Revision No. 02 FALL PROTECTION
Revision Preparation: Safety Mgr Authority: President Issuing Dept: Safety Page: Page 1 of 10 Purpose The purpose of this program is to provide fall protection procedures to prevent injury to employees
More informationFALL PROTECTION / ELEVATED WORK
SEPTEMBER CORE REFRESHER HSE TOOL BOX FALL PROTECTION / ELEVATED WORK FALL PROTECTION Falls from elevations are one of the most common causes of death in this industry. OSHA requires fall protection when
More informationOverview. Identify fall hazardous areas Describing potential fall hazards How appropriate portable and extension ladders are used
FALL PROTECTION Overview Identify fall hazardous areas Describing potential fall hazards How appropriate portable and extension ladders are used Fall Protection All situations that expose personnel to
More informationProduct Name: Internal Shock Lanyard
Product Name: Internal Shock Lanyard Part #: 11200; 11201; 11202; 11203; 21215; 01295; 01296; 01297; 01298; 11211; 11212; 11213; 11260; 11261 Instruction Manual Do not throw away these instructions! Read
More informationDREW UNIVERSITY FALL PROTECTION PROCEDURE (DRAFT 12/11)
PURPOSE The objective of this policy & guideline is to eliminate the potential for injuries and fatalities to employees and contractors resulting from falls from elevated work areas at Drew University
More informationOccupational Protective Equipment
Introduction One of the leading occupational dangers in today s workforce is the risk of death or injury due to falls. Falls from ladders, scaffolds, buildings, or other elevations have become the second
More informationProduct Name: Concrete Anchor Strap
Product Name: Concrete Anchor Strap Part #: 10705; 10710; 10715 ; 10717; 10720 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Table
More informationFall Protection STANDARD PROCEDURE INSTRUCTION. Fall Protection. Title SPI. Department. Supersedes SPI Dated. Jan 19, 2016.
STANDARD PROCEDURE INSTRUCTION Title Fall Protection Department Safety, Health and Environment Supersedes SPI Dated March 27, 2014 SPI 34-21 Effective Date Jan 19, 2016 Fall Protection SPI 34-21 Page 1
More informationWhat is fall protection?
Fall Protection Training Objective After the lecture, attendees will be able to identify fall protection equipment by understanding the ABC principle to a satisfactory level. What is fall protection? Fall
More informationUNIVERSITY OF MINNESOTA University Health and Safety FALL PROTECTION PROGRAM
UNIVERSITY OF MINNESOTA University Health and Safety FALL PROTECTION PROGRAM Effective: October 30, 2015 PURPOSE and SCOPE: The purpose of this program is to establish guidelines to protect employees and
More information2.2. Anchorage Point A secure point of attachment for Lifelines, lanyards or deceleration devices.
Title: Elevated Walking/Working Surfaces (Fall Protection) Site Function: Safety Procedure No.: MC032.122 Page: 1 of 16 McIntosh Site Reviewed: 02/2013 Effective: 03/2013 Supersedes: 08/2012 Preparer:
More informationRisk Control at United Fire Group
In the United States, falls are the leading cause of fatalities on a construction site. Employers and employees need to do the following: Where protection is required, select fall protection systems appropriate
More informationFall Protection Refresher Orientation. Fall Protection Refresher Orientation 1
Fall Protection Refresher Orientation Fall Protection Refresher Orientation 1 Course Objectives! Understand the definitions of fall prevention, fall restraint, and fall arrest.! Understand the requirements
More informationGEMTOR. ... when your life is on the line OWNER'S MANUAL. FLW Series Self-Retracting Lanyard/Fall Limiter
GEMTOR TM... when your life is on the line OWNER'S MANUAL FLW Series Self-Retracting Lanyard/Fall Limiter Installation, Operating, Inspection and Maintenance Instructions Warning You must read and fully
More informationAt the end of this presentation you should know the difference between fall prevention, fall restraint, and fall arrest.
0 At the end of this presentation you should know the difference between fall prevention, fall restraint, and fall arrest. We will review the hazards associated with fall protection and how to mitigate
More informationNew Mexico Institute of Mining & Technology. Fall Protection Program
New Mexico Institute of Mining & Technology Fall Protection Program REGULATORY STANDARDS: OSHA - 29 CFR 1910.66 29 CFR 1910.128, 129, 130, 131, (Proposed) 29 CFR 1926.104 29 CFR 1926.500 BASIS: Approximately
More informationFall Protection. 29 CFR Appendix C 29 CFR 1926 Subpart M
Fall Protection 29 CFR 1910.66 Appendix C 29 CFR 1926 Subpart M Duty to Have Fall Protection Provide fall protection systems which meet the criteria of 1926 and 1910 Make fall protection an integral part
More informationProduct Name: Hold Me Rope Anchor
Product Name: Hold Me Rope Anchor Part #: 01300 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable Safety
More informationFall Protection. Fall Protection
Fall Protection Purpose The purpose of this section is to establish protective controls for personnel working at elevated heights which will prevent or minimize injury or death resulting from falls. Scope
More informationProduct Name: Edge Series Web SRL
Product Name: Edge Series Web SRL Part #: 10900; 10901, 10909, 20900 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction
More informationFALL PROTECTION PLAN FALL PROTECTION PROGRAM
FALL PROTECTION PLAN IMPORTANT: This document is intended to provide guidance only for developing site-specific fall protection plans for working at heights. FALL PROTECTION PLAN IMPORTANT: This document
More informationThe purpose of this training is to give field technicians awareness training and guidelines on potential hazards they may encounter in the field.
Purpose The purpose of this training is to give field technicians awareness training and guidelines on potential hazards they may encounter in the field. Fall Protection and Prevention JELD-WEN Field Employees
More informationFall Protection and Elevated Work
Program No: SP-010 Page 1 1.0 PURPOSE AND INTRODUCTION Fall Protection and Elevated Work To establish fall protection safety procedures for Pitt County Schools employees engaged in any of the following
More informationCentennial Fall Protection Work Plan _CP_11_20_en_A1
Centennial Fall Protection Work Plan 0206500_CP_11_20_en_A1 Project Title: Contract and Task Order Number: Project Location (be specific, include Bldg. # / Floor / grid / etc.): PSO/SSHO Name: Complete
More informationReviewed: New Effective: 5/18/12 Supersedes: New Preparer: Owner: Approver: Team Member, Occupational Safety Industrial Hygiene
Procedure No.: BC032.027 Page: 1 of 15 Preparer: Owner: Approver: Team Member, Occupational Safety Industrial Hygiene Manager, Occupational Safety Industrial Hygiene Vice President, Ecology & Safety (Signature
More informationYou may order this publication from WCB Publications and Videos, Please quote ordering number BK60.
The following material is the property of the Workers Compensation Board of British Columbia and may not be reproduced by those outside of B.C. For those within British Columbia, this material may only
More information1.0 Scope and Application
1.0 Scope and Application This policy contains safety requirements to protect employees from falls of six (6) feet or more when performing elevated work except on ladders and scaffolding (See Ladders and
More informationFall Protection Program
Fall Protection Program 1.0 Purpose To provide guidance for the establishment of a Fall Protection Program for the Washington State Department of Transportation (WSDOT) operations and facilities as required
More informationSeasonal Employees. Increased Customer Traffic. Equipment at Full Utilization. Long Hours. Poor Weather Conditions
Seasonal Employees Increased Customer Traffic. Equipment at Full Utilization Long Hours Poor Weather Conditions Frequent meetings with employees on each shift to discuss: Tasks to be completed. Hazards
More informationProduct Name: Non-Shock Lanyard
Product Name: Non-Shock Lanyard Part #: 01121, 01122; 01280, 01250, 01255, 01260, 01265, 01251, 01261, 01265, 01270, 01271 Instruction Manual Do not throw away these instructions! Read and understand these
More informationProduct Name: Edge Angel SRL
Product Name: Edge Angel SRL Part #: 10920; 10922; 10925 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable
More informationApplying Construction Fall Protection Concepts to General Industry
Applying Construction Fall Protection Concepts to General Industry Applying Construction Fall Protection Concepts to General Industry Michael Tesmer, CSP and David Jewell, CSP Conney Safety Products This
More informationCompetent Person - Fall Protection Presented by Turner Safety- your instructor is Steve Turner
Competent Person - Fall Protection Presented by Turner Safety- your instructor is Steve Turner 1 Falls in Construction Falls are the leading cause of deaths in the construction industry. Most fatalities
More information11.4 FALL-ARREST SYSTEM AND EQUIPMENT CHECKLIST (Must answer yes to all applicable questions)
11.4 FALL-ARREST SYSTEM AND EQUIPMENT CHECKLIST (Must answer yes to all applicable questions) This checklist shall be completed either by the Competent Person or a person trained and designated by the
More informationWARNING! DO NOT THROW AWAY THESE INSTRUCTIONS! READ AND UNDERSTAND BEFORE USING EQUIPMENT!
Guardian Fall Protection Kent, WA 800-466-6385 www.guardianfall.com GENERAL SYSTEM SELECTION CRITERIA: Selection of fall protection shall be made by a Competent Person. All fall protection equipment shall
More informationQO9.d.. e v -.PXresat
BEFORE THE BOARD OF COUNTY COMMISSIONERS, COWLITZ COUNTY, WA. In the Matter of Rescinding Res. No. 93-037 Adopted 3-8 -1993 and Adopting The Updated Fall Protection Policy RESOLUTION NO. 3 n 2 WHEREAS,
More informationFALL PROTECTION SAFETY PROGRAM
FALL PROTECTION SAFETY PROGRAM REGULATORY STANDARD: OSHA - 29 CFR 1910.66-29 CFR 1910.128, 129, 130, 131, (Proposed) - 29 CFR 1926.104-29 CFR 1926.500-503 BASIS: Approximately 300,000 disabling injuries
More informationFALL PROTECTION PLAN July 2012
FALL PROTECTION PLAN July 2012 Office of Police and Safety (423)323.0255 Introduction In the construction industry in the United States, falls are the leading cause of worker fatalities. Each year, on
More informationWARNING! DO NOT THROW AWAY THESE INSTRUCTIONS! READ AND UNDERSTAND BEFORE USING EQUIPMENT!
Guardian Fall Protection Kent, WA 800-466-6385 www.guardianfall.com GENERAL SYSTEM SELECTION CRITERIA: Selection of fall protection shall be made by a Competent Person. All fall protection equipment shall
More information1.2 LIMITATIONS: Consider the following application limitations before using this equipment:
User Instruction Manual Standing Seam Roof Anchor This manual is intended to meet the Manufacturer s Instructions, and should be used as part of an employee training program as required by OSHA. Figure
More informationFALL PROTECTION PROGRAM
FALL PROTECTION PROGRAM 1.0 PURPOSE: The Indiana University (IU) is to: 1.1 Protect Indiana University employees from injuries associated with falls 1.2 Inform Indiana University employees of the hazards
More informationPart #: 42000; 42001; 42002; 42003; 42004; 42005; 42006; 42008
Product Name: Velocity SRL Part #: 42000; 42001; 42002; 42003; 42004; 42005; 42006; 42008 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment!
More informationROOFING FALL PROTECTION 27.I
ROOFING FALL PROTECTION 27.I Prior to the start of work, a structural analysis of the roof shall be conducted by a Qualified Person to assure that the load capacity of the roof deck will not be exceed.
More information??????? is committed to providing a safe work environment for its employees and preventing occupational injuries due to falls.
Intent??????? is committed to providing a safe work environment for its employees and preventing occupational injuries due to falls. Fall Protection is an integral part of our commitment to a safe work
More informationWalking-Working Surfaces and Fall Protection Standards Update. OSHA General Industry
Walking-Working Surfaces and Fall Protection Standards Update OSHA General Industry Background Slips, trips, and falls account for a majority of all general industry injury incidents. Caused 849 workplace
More informationProduct Name: Rope Grab
Product Name: Rope Grab Part #: 01500; 01503; 01505; 01506; 01507; 01511 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction
More informationUser Instructions 1790 Rail Anchor
User Instructions 1790 Rail Anchor This document is intended to meet the Manufacturer s Instruction requirements as stated by ANSI Z359.1, and should be used as part of an employee training program as
More informationReliance Industries, LLC Operating instructions for the / Bolt-on D-Ring Anchorage. Model # 3071
Reliance Industries, LLC Operating instructions for the 3071-1 / 3071-2 Bolt-on D-Ring Anchorage Model # 3071 Reliance Industries, LLC PO Box 140008 Denver, CO 80214 Ph. (800) 488-5751 Ph. (303) 424-8650
More informationWalking and Working Surfaces: Comprehensive Training
Walking and Working Surfaces: Comprehensive Training PROGRAM SYNOPSIS: To ensure workers are provided with safe working and traveling surfaces, OSHA has developed and recently updated its regulation 29
More informationWritten Program. For. Fall Protection. <<Company Name>> <<911 Address>> <<City, state, zip code>>
Written Program For Fall Protection Table of Contents Purpose.. Page 1 Policy.. Page 1 Definitions. Page 1 Fall Protection Program Responsibilities
More informationUser Instructions 1789 Parapet Wall Anchor
User Instructions 1789 Parapet Wall Anchor This manual is intended to meet the Manufacturer Instructions as required by ANSI Z359.1 and should be used as part of an employee training program as required
More informationA. Employer Provide fall protection to effected employees Ensure that all employees understand and adhere to the procedures of this plan
SECTION 10: FALL PROTECTION PROGRAM Fisher Auto Parts is committed to promoting a safe and healthy environment for all employees and customers. Protection from accidental loss of any resources, especially
More informationThis subject outlines procedures to prevent accidents or injuries to you and others from inappropriate selection and use of fall protection equipment.
Page 1 of 7 REFERENCES Personal Protective Equipment Standards 1.31 PURPOSE This subject outlines procedures to prevent accidents or injuries to you and others from inappropriate selection and use of fall
More informationTitle: Elevated Walking/Working Surfaces (Fall Protection)
Title: Elevated Walking/Working Surfaces (Fall Protection) McIntosh Site Function: Ecology, Health and Safety Procedure No.: MC032.122 Page: Page 1 of 16 Reviewed: 12/2017 Effective: 01/2018 Supersedes:
More informationFall and Slip Prevention Test. 1. Fall protection is required in construction at and on scaffolds at.
Date... Name... WSU ID... Fall and Slip Prevention Test 1. Fall protection is required in construction at and on scaffolds at. a) 6 and 10 feet b) 1 and 2 feet c) Not required d) 4 feet for both 2. Falls
More informationThanks To Our Sponsors Platinum Sponsor NS Department of Labour and Workforce Development
March 25, 26, 27, 2009 Thanks To Our Sponsors Platinum Sponsor NS Department of Labour and Workforce Development Special Event Sponsor Workers Compensation Board of Nova Scotia Gold Sponsors Maxwell Promotions
More informationProduct Name: Angel Anchor
Product Name: Angel Anchor Part #: 00260 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable Safety Standards
More informationWork At Heights Toolkit. for Supervisors
Work At Heights Toolkit for Supervisors For Supervisors How to use this toolkit? The toolkit aims to provide information for supervisor to communicate one topic a day to workers. Pictures are for illustration
More informationPatrick Harel Ph
Patrick Harel Ph- 920-418-2714 pharel@capitalsafety.com The Worldwide Experts in Fall Protection Standards Occupational Safety and Health Administration (OSHA) 29 CFR 1910 and 1926 Governing Body Sets
More informationProduct Name: Bull Ring Anchor
Product Name: Bull Ring Anchor Part #: 00484 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable Safety Standards
More informationFall Protection Guidelines. Individual Unit Function: Safety Procedure No.: SOP-0111 Page: 1 of 13. Preparer: Owner: Approver: Safety Safety Safety
Procedure No.: SOP-0111 Page: 1 of 13 MIDGA Reviewed: 09/187/1 Effective: 09/17/17 Supersedes: Ver. 1.0 7 1. PURPOSE These guidelines are to provide minimum standards for work on corrugated roofing, structural
More informationFALL PROTECTION PROGRAM (OHS-0010)
() For Issued: December 17, 2007 Revised: 1 st Issue PAGE 1 OF 17 Table of Contents 1.0 Purpose...2 2.0 Document Control...2 2.1 Approvals...2 2.2 Responsibility...2 3.0 Definitions...3 4.0 Objective...7
More informationUser Instruction Manual Fixed Beam Anchor
Instructions for the following series products: FIXED BEAM ANCHOR Model Numbers: The Ultimate in Fall Protection 2108406 2108407 2108408 2108409 2108410 2108411 User Instruction Manual Fixed Beam Anchor
More informationFALL PROTECTION PLAN
FALL PROTECTION PLAN CPWR The Center for Construction Research and Training created this document as part of the National Campaign to Prevent Falls in Construction to provide companies with guidance on
More informationProduct Name: Snappy Anchor
Product Name: Snappy Anchor Part #: 00710; 00711; 00715-TV Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable
More informationHealth, Safety, Security and Environment
Document owner and change code Document Owner Aaron Perronne Title HSSE Manager Mark X Change Code Description X N/A First Issue A Typographical/Grammatical correction; formatting change; text clarification-no
More informationFALL PROTECTION CODE OF PRACTICE
FALL PROTECTION CODE OF PRACTICE This guide can help you comply with Section 50.2 of the General Regulation 91-191. NOTE: Not for use when a safety monitor is part of the fall protection system on a work
More informationOPE Training Seminar Agenda
OPE Training Seminar Agenda Basics -OSHA - Industry Symbols - A,B,C s - Types of OPE Systems - Selection of an OPE System - Inspection & Maintenance - Safety Tips (OSHA) OCCUPATION SAFETY AND HEALTH ADMINISTRATION
More informationFall Protection University Facilities Internal Procedure: July 1, 2013 Effective date: July 1, 2013 Last Modified: April 2013 Approved by: Bob Wells
Fall Protection University Facilities Internal Procedure: July 1, 2013 Effective date: July 1, 2013 Last Modified: April 2013 Approved by: Bob Wells 1.0 Program Objective UF has adopted this policy to
More informationFall Protection Introduction
Fall Protection Introduction Date: District: Site: Time: Department: Manager/Supervisor Name: In 1995, 1,048 construction workers died on the job, with 32 percent, or 335 of them, resulting from falls.
More information1 of 15. Policy Number 61. Last Update: March 21, Effective Date: 11/22/11 Resolution No Title: Fall Protection Policy POLICY STATEMENT
Policy Number 61 Effective Date: 11/22/11 Resolution No. 476-11 Title: Fall Protection Policy Last Update: March 21, 2011 POLICY STATEMENT The objective of the Cayuga County (County) Fall Protection Policy
More informationOperating instructions. Bolt-on Bar Joist Anchorage
Reliance Industries, LLC Operating instructions for the Bolt-on Bar Joist Anchorage Model # 3072 Reliance Industries, LLC PO Box 140008 Denver, CO 80214 Ph. (800) 488-5751 Ph. (303) 424-8650 Fax (303)
More informationProduct Name: 2-Way Standing Seam Roof Clamp
Product Name: 2-Way Standing Seam Roof Clamp Part #: 10600 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable
More informationFACILITIES MANAGEMENT OFFICE OF ENVIRONMENTAL HEALTH AND SAFETY Fall Protection Policy 11/21/14 Last Revision
FACILITIES MANAGEMENT OFFICE OF ENVIRONMENTAL HEALTH AND SAFETY Fall Protection Policy 11/21/14 Last Revision INTENT To provide written procedures and guidelines for all University at Albany employees
More informationTAMPA ELECTRIC COMPANY ENERGY SUPPLY FALL PROTECTION PROGRAM
TABLE OF CONTENTS TITLE PAGE # PURPOSE / INTRODUCTION 1 RESPONSIBILITY 2 EMPLOYEE TRAINING INCLUDING DOCUMENTATION 3 PROGRAM REQUIREMENTS 4-5 HAZARD ASSESSMENT / IDENTIFICATION 5 EQUIPMENT INSPECTION 6-8
More informationWalking-Working Surfaces Fall Protection Program
Purpose Walking-Working Surfaces Fall Protection Program The purpose of this program is to provide procedures to eliminate, prevent, and control hazards from falls from heights. Scope This program is applicable
More informationSafety Tips from the WorkSafe People
Fall Protection Fall Protection Requirements Fall Hazard Locations Fall Prevention Personal Fall Arrest System 1 F AL5000(11/02) Fall Protection Any construction activity that exposes an employee to a
More informationFREQUENTLY ASKED QUESTIONS ABOUT FALL PROTECTION
FREQUENTLY ASKED QUESTIONS ABOUT FALL PROTECTION What s the difference between polyester and nylon webbing in harnesses and lanyards? Nylon (polyamide) and polyester are both synthetic products with very
More informationProduct Name: 2-Way Standing Seam Roof Clamp. Instruction Manual. Part #: 10600
Product Name: 2-Way Standing Seam Roof Clamp Part #: 10600 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Table of Contents Introduction
More informationCHAPTER 10 FALL PROTECTION
CHAPTER 10 FALL PROTECTION A. INTRODUCTION... 1 B. CHAPTER-SPECIFIC ROLES and RESPONSIBILITIES... 2 C. HAZARD IDENTIFICATION... 3 1. Job Hazard Analysis (Jha).... 3 2. Fall Hazards... 3 D. HAZARD CONTROL...
More informationINSTRUCTIONS FOR USE
INSTRUCTIONS FOR USE 88004X Series D-Ring Extender 5000 lb Rated Connector Complies with ANSI Z359.1-1998, ANSI 10.14 and OSHA 1926 regulations and requirements. Reliance Industries P.O. Box 2046 Deer
More information29 CFR 1926, Subpart M. Fall Protection Program Table of Contents
I. Objective II. Policy III. Assignment of Responsibility IV. Training V. Controlled Access Zones VI. Excavations VII. Fall Protection Systems A. Covers B. Guardrail Systems C. Personal Fall Arrest Systems
More informationINSTRUCTIONS FOR USE
INSTRUCTIONS FOR USE 68XXXX Series Anchorage Slings Complies with the current ANSI Z359.1-2007 and all applicable OSHA regulations and requirements. Reliance Industries P.O. Box 2046 Deer Park, TX 77536
More informationOSHA 29CFR 1910 Subpart D Walking-Working Surfaces Content
OSHA 29CFR 1910 Subpart D Walking-Working Surfaces Content 1910.28 Duty to have Fall Protection and Falling Object Protection 1910.29 Fall Protection Systems and Falling Object Protection Criteria and
More informationFALL PROTECTION COMPARISON BETWEEN VARIOUS OSHA STANDARDS, NAVY and EM 385 (2008) REQUIREMENTS
Requirements FALL PROTECTION COMPARISON BETWEEN VARIOUS OSHA STANDARDS, NAVY and EM 385 (2008) REQUIREMENTS Navy FP Chapter 13 of OPNAVINST 5100.23G (2005) and Fall Protection Guide for Ashore Facilities
More information"FALL PREVENTION IN THE WORKPLACE"
MAJOR PROGRAM POINTS "FALL PREVENTION IN THE WORKPLACE" Part of the "GENERAL SAFETY SERIES" Quality Safety and Health Products, for Today...and Tomorrow Outline of Major Points Covered in the "Fall Protection"
More informationProduct Name: Beamer Instruction Manual. Part #: 00110
Product Name: Beamer 12-1 Part #: 00110 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Guardian Fall Protection 6305 S. 231st St.,
More informationFALL PROTECTION GUIDELINE
FALL PROTECTION GUIDELINE July 2001 Table of Contents INTRODUCTION...3 CONTROL MEASURES...4 SURFACE PROTECTION...4 FIXED BARRIERS...5 EXAMPLES OF GUARDRAIL...6 WARNING BARRIERS...7 HANDRAILS...8 SURFACE
More information"FALL PROTECTION IN CONSTRUCTION ENVIRONMENTS"
MAJOR PROGRAM POINTS "FALL PROTECTION IN CONSTRUCTION ENVIRONMENTS" Part of the "CONSTRUCTION SAFETY KIT" Series Quality Safety and Health Products, for Today...and Tomorrow OUTLINE OF MAJOR PROGRAM POINTS
More information