CLEANING HANDGUNS TOOLS YOU WILL NEED
|
|
- Jennifer Singleton
- 5 years ago
- Views:
Transcription
1 CLEANING HANDGUNS
2 CLEANING HANDGUNS If you take pride in your firearm, then you know how important it is to properly maintain your weapon. With good, consistent care, you not only make your gun look good on the outside, but you also keep the mechanics clicking smoothly and efficiently on the inside. The importance of a clean firearm cannot be overstated. In truth, a weapon s malfunctions are most often caused by dirt, rather than a more serious problem with the gun s internal mechanics. By learning the proper way to maintain your firearm, you can correct and perhaps prevent some of the common ailments that can affect your weapon s performance. This is especially true with revolvers. Compared to rifles and shotguns, handguns endure the most abuse during a shooting session because shooters typically take 50 to 100 rounds just to get warmed up. Rifle users, on the other hand, typically shoot no more than 20 to 30 rounds per stint. TOOLS YOU WILL NEED > Eye protection > Bore guide > Pull cable > Patches > Cleaning rod (preferably nylon single-piece) > Brushes > Eyelet/jag > Shop cloths > Lead-removing solvent > Cleaner > Lubricant > Chamber cleaning tool kit > Bore light
3 CLEANING A REVOLVER As a revolver owner, you may have been told that a good way to clean is to disassemble the pistol, place it in a solvent bath and then slather it in oil. But that is not a recommended method. Too much solvent can dissolve gun grease that may be in the mainspring housing area, and heavy oil is a magnet for dirt. Instead, we recommend the following techniques for cleaning your handgun. But first, the most important step: Make sure the handgun is safe to clean. To clear a weapon, open the action of the firearm and visually and manually check the chamber. CLEANING STEPS 1.Cleaning the cylinder requires the > Open the cylinder and scrub it with a solvent. NOTE: Make sure to use a lead-removing solvent to deep clean the forcing cone, barrel and chambers. This is because most revolver ammunition is either semi-jacketed or not jacketed at all. Although other kinds of cleaners can be effective at eliminating powder residue, they may still leave behind flaky, dark debris. A lead remover can take care of it all. > Clean the cylinder stops (notches on the cylinder) by scrubbing the area with a bristle brush. If this is not effective enough, use a brass scrubbing tool or the end of a wooden match to thoroughly remove the powder residue. 2.Cleaning the forcing cone and barrel requires the > The forcing cone receives the most amount of carbon and powder residue, so make sure to clean it with a good solvent. This area also collects a large amount of lead deposits. > After scrubbing the barrel with solvent, dry thoroughly with a patch from breech to muzzle. Keep in mind that placing oil down the barrel is not necessary. 3.Cleaning the individual chambers requires the > With the cylinder open, clean inside each chamber with a brush and solvent. Next, depress the ejector rod and scrub both the rod and ratchet. Once finished, make sure to completely dry the areas with a clean rag. > To remove lead from the chambers, use a brass brush or a jag with a brass screen. Clean the areas with solvent and dry completely. NOTE: You may want to try the Lewis Lead Remover Pistol and Revolver kit, which includes brass patches and a rubber arbor to clean out the lead deposits imbedded in both the chamber and the bore. This product works well with JB Bore Compound. 4.The next step is cleaning the recoil plate, where the firing pin contacts the primer of the round. Wipe with a dry rag to remove the powder residue, and then scrub with solvent to get rid of any carbon. Remember that the heat mark left on the plate near the firing pin is permanent. 5.Detailed cleaning of the revolver requires the > For deep cleansing, you must first remove the crane by unscrewing the crane screw. Clean the crane with solvent and then add a small amount of oil to the crane, as well as to the ejector rod and spring area. NOTE: Be advised that each revolver has a different method of crane removal, so be sure to research the model you are working on. > Next, remove the grip, use solvent to scrub the exposed areas and then dry with a clean rag. If needed, apply new grease to the main spring. > Remove the screws or use a punch set to open the actual frame, and then spray inside with an acetone-based liquid or Gun Scrubber. If any of the internal areas have old gun grease, reapply with new gun grease. Finally, use the pistol s schematic instructions to reinstall all of the components.
4 CLEANING A POLYMER PISTOL Most weapons owners probably have a modern polymer pistol in their collection. After all, this is one of the most popular styles of handguns on the market. Although some features are common between models, there can be differences when it comes to disassembly and cleaning. Make sure you check the manual on your revolver before you attempt to clean it. CLEANING STEPS 1.Disassembly of most polymer pistols requires the following: > Start by retaining the slide slightly back and holding it to the rear. At the same time, depress the slide lock. > When you pull the trigger, the slide will be released, along with the barrel assembly. > Depress the rod to take out the spring and guide rod. > Remove the barrel assembly 2.Cleaning the barrel requires the > First, scrub the barrel with solvent. Pay close attention to the feed ramp, as there may be excessive copper fouling or carbon buildup that can create feeding issues. > Use a brush, copper solvent and patches to clean the bore and then dry completely. You do not need to put oil in the chamber or bore. > Oil the barrel lug and outside of the barrel. 3.Cleaning the pistol grip and lower receiver requires the > Scrub the receiver with solvent and then dry with an air hose. Make sure you do not apply excessive oil to the internal trigger mechanism. > Place one drop of oil on each of the four slide rail cuts. 4.Clean the slide by removing all of the carbon and dirt from the slide housing. Once complete, apply a small amount of oil to the slide rails. 5.Cleaning the magazine requires the > Using a punch, depress the retaining pin on the magazine to separate the magazine sleeve from the magazine spring. > Scrub the magazine with a brush and solvent and then dry completely. CLEANING A 1911 PISTOL The John Moses Browning design also known as the 1911 pistol is legendary for many reasons, including its specialized mechanics. Because some of its schematics vary greatly from the other semi-auto polymer pistols and revolvers of today, here are the details on how to properly disassemble and clean this firearm. CLEANING STEPS 1.Removing the slide and barrel requires the > First, pull the slide back, locking it in the open position. After you visually and physically inspect the chamber, remove the magazine. > Because the design has a two-piece guide rod, you will need to use a 5/32 Allen wrench to remove the forward piece. > With the slide forward, and facing the muzzle of the pistol, press the recoil spring plug inward until the barrel bushing is free to be twisted clockwise, until it uncovers completely the recoil spring plug. The recoil spring plug is under pressure from the recoil spring, so keep pressure on the plug, and release the spring pressure slowly. Remove the recoil spring plug and the recoil spring. Remove the barrel bushing by twisting it clockwise until it comes off. > Pull the slide to the rear, until the release lever end is aligned with the small circular notch on the left side of the slide.
5 > Push the axis of the slide release lever from the right side of the gun toward the left side. When the lever pops out, pull it completely off the frame of the gun. > Remove the recoil spring guide and rotate the barrel link so it is placed directly on top of the barrel. From here, you can remove the barrel from the slide housing. The weapon is now field stripped. 2.Cleaning the barrel requires the > The most significant difference between the 1911 barrel and others is the unique locking lug feature (also found in the Browning Hi-Power), which is important to the short-recoil operation of the pistol. The lugs are located on the top of the barrel and should be thoroughly clean with solvent and a brush. > Clean the bore with a set of brushes and patches, and make sure to keep the barrel and chamber dry. Apply a small amount of lubrication to the locking lug area and barrel. 3.Cleaning the slide requires the > Using solvent, clean the recess lugs inside the top frame and then dry completely. Always inspect if the lugs or the recess areas are worn. > Next, clean the breech face, where erosion can quickly occur. Scrub with solvent and dry completely. You can ignore any heat marks that will typically stain this area. > Clean the slide rails with solvent and run a patch to completely dry the area. Oil this area lightly. > Keep the extractor and extractor channel dry and free of lube. 4.Cleaning the frame requires the > Start by scrubbing the magazine well with solvent and then drying with an air hose or with a clean rag. > After cleaning the rails with solvent, make sure they are completely dry and then apply a small amount of oil. 5. Advanced cleaning requires the > First, remove the grips with a slotted screwdriver or Allen wrench, and then spray the frame with Birchwood Casey Gun Scrubber or another aerosol cleaner/degreaser. > Every so often, it s important to clean the firing pin area and extractor: > Depress the firing pin, and remove the plate. NOTE: A newer design of the 1911 is commonly referred to as the Series 80, which includes a firing pin block in this area. The Series 70 does not have this feature. To remove the plate, depress the safety plunger at the same time that you depress the firing pin. The plate should be easy to remove at this point. Make sure these small parts are placed in a magnetic dish or on a dry towel. > Remove the firing pin and extractor from the rear of the slide. > Depress the extractor on the front of the breech face and the firing pin block should just fall out. > Clean these small parts with solvent and completely dry. BASIC STEPS TO PROPER FIREARM MAINTENANCE > Clean barrel and metal parts with a good commercial solvent. > Clean bore until dry patch comes through as clean as possible. > Run oily patch through barrel. > Bore should be cleaned through breech end where possible. > All metal parts should get light coat of oil. > Store in horizontal position. > After storage, run clean patch through bore before firing. > Remove all excess grease and oil.
6 CLEANING A BREAK-OPEN ACTION SHOTGUN Break-open action shotguns are often the oldest and/or most valuable firearms in an owner s collection. As a result, they typically need a higher amount of care. It is not particularly difficult to clean a break-open shotgun. Most shooters focus on the bore, chamber and choke areas for general maintenance. That s because detailed cleaning of the firing mechanism may not always be necessary. It is separated in large part by the breech block and does not collect a lot of carbon or dirt. In addition, a general rule for any shotgun with a wooden stock (especially ones with ornate engraving) is to never apply solvent to a non-metal part of the firearm. 1.General cleaning tips: 1.Most break-open barrels can be easily removed by using a snap lever at the forend. 2.Hold the barrel and press the release lever as if you are loading the shotgun. This should remove the barrel. 3.When the barrel is detached, the shotgun will be in its three main pieces. 4.If you are performing general bore cleaning, use the same procedure as outlined for autoloading shotguns. 5.After each use, apply new grease to the hinge pin, knuckle, cocking lever pin and front lug. 6.If there are wooden parts, treat the stock like any other wooden piece of furniture by wiping it down with a clean cloth and using wax or polish for a final shine. Note: Be careful not to apply too much petroleum-based gun oil or mineral spirits. Over time, it will ruin the wood s finish. 2. Detailed cleaning tips: 1.If a shotgun has been used in inclement weather, it is recommended that you dissemble the extraction lever from the barrel assembly. Be aware of your model because many require specialized tools. 2.After removing the extractor, scrub with a brush and solvent, preferably acetone-based because that is best for deep cleaning. Soak any rusted parts. 3.Another aspect of deep cleaning is the disassembly of the stock so you can reach the trigger assembly and internal parts. Some gunsmiths recommend this type of maintenance be done once a year. However, it takes special knowledge and tools to remove this part of the shotgun. If you attempt this process, it is advised that you strip the old gun grease with solvent, dry thoroughly and then reapply new grease All rights reserved. Except for use in a review, no portion of this book may be reproduced, stored in or introduced into a retrieval system, or transmitted in any form without the express written permission of Sonoran Desert Institute. The scanning, uploading, and distribution of this book by the Internet or any other means without the permisson of Sonoran Desert Institute is illegal and punishable by law. Please respect Sonoran Desert Institute s rights and do not participate in any form of electronic piracy or copyrighted material. Sonoran Desert Institute does not assume any responsibility for the use or misuse of information contained in this book.
Cleaning rod: spring steel, stainless steel or carbon fibre cleaning rod - only use a one-piece rod. Avoid using snakes.
Telemark Biathlon Where performance and precision come together http://telemarkbiathlon.com Rifle Cleaning Date : July 19, 2013 Anschutz Rifle Manual - Click Here Izhmash 7-3 Rifle Manual - still looking
More informationINSTRUCTION MANUAL CZ 75 Champion
INSTRUCTION MANUAL CZ 75 Champion CZ 75 CHAMPION - INSTRUCTION MANUAL Before handling the pistol read this manual carefully and observe the following safety instructions. Improper and careless handling
More informationM16 R / M1600 R USER S MANUAL WARNING: READ THE INSTRUCTIONS AND SAFETY PRECAUTIONS IN THIS MANUAL CAREFULLY BEFORE USING THIS FIREARM.
ARMSCOR M16 R / M1600 R USER S MANUAL WARNING: READ THE INSTRUCTIONS AND SAFETY PRECAUTIONS IN THIS MANUAL CAREFULLY BEFORE USING THIS FIREARM. DISCHARGING FIREARMS IN POOLY VENTILATED AREAS, CLEANING
More informationINSTRUCTION MANUAL CZ 92
INSTRUCTION MANUAL CZ 92 Before handling the pistol read this manual carefully and observe the following safety instructions. Improper and careless handling of the pistol could result in unintentional
More informationINSTRUCTION MANUAL CZ 75 TS
INSTRUCTION MANUAL CZ 75 TS CZ 75 TS - INSTRUCTION MANUAL Before handling the pistol read this manual carefully and observe the following safety instructions. Improper and careless handling of the pistol
More informationCHAPTER 2 MAINTENANCE
CHAPTER 2 MAINTENANCE This chapter addresses the proper care of the machine gun to ensure its overall effectiveness and efficient functioning. The information includes the gunner's knowledge in disassembly
More informationArmed Officer's Training Manual Nomenclature and Inspection
Armed Officer's Training Manual Section 8: Nomenclature and Inspection Learning Goal: The student will know the components and understand the operation of the service revolver and semi-automatic pistol.
More informationSAFETY RULES WARNING: READ THESE SAFETY RULES & OPERATORS MANUAL BEFORE HANDLING YOUR FIREARM
SAFETY RULES WARNING: READ THESE SAFETY RULES & OPERATORS MANUAL BEFORE HANDLING YOUR FIREARM Never point a firearm at anyone and always keep the muzzle pointed in a safe direction. Always treat all firearms
More informationSTRIBOG GRAND POWER. The INSTRUCTIONS FOR USE, MAINTENANCE AND SAFETY. 1
instructions The for use, maintenance STRIBOG and safety hestribog GRAND POWER INSTRUCTIONS FOR USE, MAINTENANCE AND SAFETY www.grandpower.eu 1 The STRIBOG Dear Customer, Thank you for purchasing a semi-automatic
More informationDisassembly, Assembly, and Cleaning of M16A4/M4
Table of Contents iii Disassembly, Assembly, and Cleaning of M16A4/M4 By: George Carter Chris Talbott Jeremy Tinker Table of Contents Introduction... vii Disassembly... 3 Clearing the Magazine... 3 Retaining
More informationBasic Pistol Test Study Guide
1. The three major components of a pistol are: a. barrel, action and grip b. frame, barrel and action c. barrel, frame and hammer d. cylinder, frame and barrel Basic Pistol Test Study Guide 2. A cylinder
More informationOPERATOR S MANUAL FOR AR-24 SERIES PISTOLS
OPERATOR S MANUAL FOR AR-24 SERIES PISTOLS ArmaLite Incorporated Box 299 Geneseo Illinois U.S.A. 61254 309-944-6939 ArmaLite.com 2006 ArmaLite Inc. This book provides instructions on the operation and
More informationCZ 40 P - INSTRUCTION MANUAL
Before handling the pistol read this manual carefully and observe the following safety instructions. Improper and careless handling of the pistol could result in unintentional discharge and could cause
More informationKEEP YOUR 1911 WORKING UNTIL 2111 THE DEFINITIVE GUN-CARE GUIDE
KEEP YOUR 1911 WORKING UNTIL 2111 THE DEFINITIVE GUN-CARE GUIDE TABLE OF CONTENTS 2 3 4-5 INTRODUCTION MAINTENANCE SCHEDULE PRODUCTS 8-10 11-12 13 LUBRICATION MAGAZINE MAINTENANCE CONCLUSION 6-7 CLEANING
More informationAR-15 Rifle Operator Maintenance
AR-15 Rifle Operator Maintenance These procedures cover how to Clean, Inspect and Lubricate the AR15 Rifle NOTICE: This is not a replacement for the manufacturer s manual. If you do not have the owners
More informationMECH-TECH SYSTEMS CCU MODEL FOR GLOCK PISTOLS
MECH-TECH SYSTEMS CCU MODEL FOR GLOCK PISTOLS Operation & Maintenance Manual Read and understand this manual before attempting to use this product. If you have any questions call: 1-866-433-2122 www.mechtechsys.com
More informationCONTENTS INTRODUCTION. WARNING: This manual contains important warnings that must be understood before using this firearm.
CONTENTS Safety Rules...............................Page 2 Operation................................Page 5 Major Components.........................Page 6 Assembly.................................Page
More informationCOLT AUTOMATIC PISTOL
COLT AUTOMATIC PISTOL CALIBER.22 INSTRUCTIONS FOR ASSEMBLY - DISASSEMBLY CLEANING COLT AIUTOMATIC PISTOL IN 6 INCH OR 4}~2 INCH BARREL.22 Long Rifle, rim fire Cartridge Capacity of Magazine, 10 Shots Description
More informationPistol Maintenance: Key Lubrication Points
usacarry.com http://www.usacarry.com/pistol-maintenance-key-lubrication-points/? utm_source=getresponse&utm_medium=email&utm_campaign=usacarry&utm_content=pistol+maintenance:+key+lubrication+points Pistol
More informationAR /.223, 300 BLK, 22 Nosler,.224 Valkyrie. Covers. and. rifle models INSTRUCTION MANUAL
AR-15 5.56/.223, 300 BLK, 22 Nosler,.224 Valkyrie Covers TM, TM and, TM rifle models INSTRUCTION MANUAL WARNING: BEFORE USING THIS FIREARM, READ AND FOLLOW THESE INSTRUCTIONS Safety First Thank you for
More informationOWNER S MANUAL. Read the instructions and warnings in this manual carefully before using this firearm; do not discard this manual.
OWNER S MANUAL SDP compact Read the instructions and warnings in this manual carefully before using this firearm; do not discard this manual. This instruction manual should always accompany this firearm
More informationHISTORY DESIGN SAFETY
GLOCK 17 HISTORY The Glock 17, designed by Gaston Glock, was adopted by the Austrian Army as its service pistol in 1982. As an Austrian engineer with no prior firearms design experience, this was Glock
More informationSEMIAUTOMATIC SHOTGUN OWNER'S MANUAL
SEMIAUTOMATIC SHOTGUN OWNER'S MANUAL ARMSAN@ARMSAN.COM TECHNICAL DATA Caliber :12 gauge / 20 gauge / 28 gauge Operation: Semi-Automatic, Gas Operated System Barrel Length: 20 (51cm), 24 (61cm), 26 (66cm),
More informationINSTRUCTION MANUAL FOR. Models featured include: LF556, LF300, LF308, and LF6.5.
INSTRUCTION MANUAL FOR Models featured include: LF556, LF300, LF308, and LF6.5. READ THIS MANUAL THOROUGHLY, PARTICULARLY THE WARNINGS, BEFORE USING THIS FIREARM Copyright 2016 Live Free Armory. All rights
More information-
Operator s manual SM-95202 Brügger & Thomet AG P.O. Box 42 3608 Thun Switzerland Fon +41 33 334 67 00 Fax +41 33 334 67 01 info@brugger-thomet.ch www.brugger-thomet.ch TABLE OF CONTENTS SAFETY instructions
More informationOPERATION & SAFETY MANUAL
ARMS MANUFACTURING INCORPORATED 1911 Pistols OPERATION & SAFETY MANUAL We specifically disclaim any responsibility for damage or injury whatsoever incurred as a result of the use of faulty, sub-standard
More informationODEL 95 OPERATOR S MANUAL
ODEL 95 MODEL 95 OPERATOR S MANUAL TABLE OF CONTENTS 2 2 3 5 6 6 6 7 7 8 8 11 11 12 12 19 20 22 24 26 MANUFACTURER S DISCLAIMER USE OF THE MANUAL SAFETY GUIDELINES WARRANTY AND SERVICE DESCRIPTION OF FIREARM
More informationOwners Manual MAX-10/45 Upper Receiver. Rev. A. NFA Warning. LAGE Manufacturing, L.L.C. 916 E. Baseline Rd. STE #113 Mesa, AZ 85204
Owners Manual MAX-10/45 Upper Receiver NFA Warning LAGE Manufacturing, L.L.C. 916 E. Baseline Rd. STE #113 Mesa, AZ 85204 CM109mk2-300 Rev. A This upper receiver is designed to be used with the M-10/45
More informationINTRODUCTION TO THE SERVICE RIFLE AND MAINTENANCE
INTRODUCTION TO THE SERVICE RIFLE AND MAINTENANCE 1 OVERVIEW DISASSEMBLY MAINTENANCE ASSEMBLY 2 TERMINAL LEARNING OBJECTIVE Given a service rifle, Common Combat Sling, and cleaning gear maintain a service
More informationVR1 Owner s Manual. Vigilance Rifles, Inc Plum Lane Redlands, CA P F
VR1 Owner s Manual Vigilance Rifles, Inc. 1653 Plum Lane Redlands, CA 92374 P 909.307.8877 F 909.307.8866 www.vigilancerifles.com INTRODUCTION: Vigilance Rifles offers a new line of Semi-Automatic Rifles
More informationMCMILLAN TAC -SERIES G30 TACTICAL RIFLE S H O O T T O W I N
O W N E R S M A N U A L MCMILLAN TAC -SERIES G30 TACTICAL RIFLE S H O O T T O W I N Congratulations. You are now the owner of the finest firearm that technology, craftsmanship and art can build. Please
More informationINSTRUCTION MANUAL CZ 750
INSTRUCTION MANUAL CZ 750 Before handling the firearm read this manual carefully and observe the following safety instructions. Improper and careless handling of the firearm could result in unintentional
More informationSmallbore rifle CZ99 PRECISION..22 Long Rifle.22 Win. Mag. R.F..17 Hornnady Mag. R.F.
Smallbore rifle CZ99 PRECISION.22 Long Rifle.22 Win. Mag. R.F..17 Hornnady Mag. R.F. Fig. 1 22. Long Rifle, Model CZ 99 PRECISION 22 Long Rifle 22 Long Rifle for Sound Moderator 22 Win. Mag. R. F. 17
More informationautoloading pistol owner s manual
1911-22 autoloading pistol owner s manual Important operating instructions for: Browning 1911-22 autoloading pistol If you have any questions or comments regarding your new firearm, please contact us.
More informationInstruction manual CZ 75
Instruction manual CZ 75 Before handling the pistol read this manual carefully and observe the following safety instructions. Improper and careless handling of the pistol could result in unintentional
More informationUSER MANUAL TEDNA Shotguns. Over & Under Side by Side Semi-Automatic
USER MANUAL TEDNA Shotguns Over & Under Side by Side Semi-Automatic Zenith Firearms www.zenithfirearms.com Come shoot the quality. Zenith Firearms, an American importer of high quality fi.rearms.and.accessories,.is.a.proud.distributor.of.
More informationModel 1911 Series Pistols SAFETY & INSTRUCTION MANUAL
REGENT Model 1911 Series Pistols 01 SAFETY & INSTRUCTION MANUAL READ AND UNDERSTAND THE INSTRUCTIONS AND WARNINGS IN THIS MANUAL CAREFULLY, BEFORE USING THIS FIREARM. FAILURE TO READ THESE INSTRUCTIONS
More informationautoloading pistol owner s manual
browning.com BROWNING US: Morgan, Utah 84050-9326 BROWNING CANADA: Browning Canada Sports Ltd/Ltée, St-Laurent, Quebec H4S 1W6 BROWNING INTL: Parc Industriel des Hauts-Sarts, B-4040 Herstal, Belgium NEU101015.5/10452
More informationUSER'S MANUAL AZUR. Barrel lugs. Forearm. iron. Receiver
USER'S MANUAL AZUR Barrel Hinge pin Barrel lugs Chamber Top lever Muzzle Safety Forearm lug Forearm latch Forearm Forearm iron Receiver Trigger Buttstock IT IS YOUR RESPONSABILITY FAILURE TO HEED ANY OF
More informationMontana Firearms Group Montana Rifle Company Model 1999 INSTRUCTION MANUAL
Montana Firearms Group Montana Rifle Company Model 1999 INSTRUCTION MANUAL Important Instructions for Model 1999 Montana Action Bolt Rifle Receiver Montana Rifle Company 3172 MT Hwy 35 Kalispell, MT 59901
More informationBefore handling the pistol read this manual carefully and observe the following safety instructions. CONTENTS
Before handling the pistol read this manual carefully and observe the following safety instructions. Improper and careless handling of the pistol could result in unintentional discharge and could cause
More informationOwners Manual MAX-10/9 mk2 Upper Receiver. LAGE Manufacturing, L.L.C. 916 E. Baseline Rd. STE #113 Mesa, AZ Rev. A
Owners Manual MAX-10/9 mk2 Upper Receiver LAGE Manufacturing, L.L.C. 916 E. Baseline Rd. STE #113 Mesa, AZ 85204 CM109mk2-300 Rev. A NFA Warning This upper receiver is designed to be used with the M-10/9
More informationSterling Shotguns. Field and Target Models. Owner s Manual
Sterling Shotguns Field and Target Models Owner s Manual If you have any questions about the safe use of a Big Horn Armory firearm, call us at 307-586-3700 or write us at P.O. Box 940, Cody Wyoming 82414.
More informationAR STYLE FIREARMS OWNER'S MANUAL: OPERATION, HANDLING, DISASSEMBLY / REASSEMBLY & SAFETY INSTRUCTIONS
AR STYLE FIREARMS OWNER'S MANUAL: OPERATION, HANDLING, DISASSEMBLY / REASSEMBLY & SAFETY INSTRUCTIONS - DO NOT DISCARD THIS MANUAL - READ THIS MANUAL CAREFULLY, PAYING CLOSE ATTENTION TO THE INSTRUCTIONS
More informationFRONT BOLT ACTION ASSAULT SHOTGUN
SPECIFICATIONS: CATEGORY........... IMPROVISED; NOTE: CAN BE MANUFACTURED COMMERCIALLY CALIBRE............ 410 TO 12 GAUGE; ADAPTABLE CAPACITY............... 8 TO 10 ROUNDS,.410 CAL. OPERATION..........
More information- SAFETY - FIRST AND FOREMOST
- SAFETY - FIRST AND FOREMOST FIREARMS ARE DANGEROUS WEAPONS, WHICH CAN CAUSE SERIOUS INJURY OR DEATH. WHEN USING ANY FIREARM, SAFETY MUST BE YOUR FIRST AND CONSTANT CONCERN. READ AND UNDERSTAND THE FOLLOWING
More informationNOTICE FEATURES BACKGROUND
,/ NOTICE Claims will not be honored for damage, injury or, death resulting from the intentional or accidental discharge of this firearm, or from it's function when used for purposes or subjected to treatment
More informationBefore handling the firearm read this manual carefully and observe the following safety instructions. CONTENTS
Before handling the firearm read this manual carefully and observe the following safety instructions. Improper and careless handling of the firearm could result in accidental discharge and cause injury,
More information1. TABLE OF CONTENT. 9.4 Preserving Exploded drawing of K22 with components Component list of K22 model Warranty...
1. TABLE OF CONTENT 1. Table of content...2 2. Records of firearm s owner...3 3. Basic description...5 4. Technical specifications...6 5. Serial number of pistol...7 6. Main parts of pistol...8 7. Basic
More informationCleaning and maintaining the M14/M1A rifle
Cleaning and maintaining the M14/M1A rifle Part 1, simple maintenance after a day at the range Always clean your rifle when you get home from the range, if you don t it will affect the rifle and you ll
More informationO W N E R S M A N U A L
O W N E R S M A N U A L MCMILLAN TAC -50 MCMILLAN TAC -50 A1 MCMILLAN TAC -50 A1-R2 S H O O T T O W I N Congratulations. You are now the owner of the finest firearm that technology, craftsmanship and art
More informationARAK-21 OPERATOR SAFETY AND INSTRUCTION MANUAL
ARAK-21 OPERATOR SAFETY AND INSTRUCTION MANUAL NOTICE: The ARAK-21 Upper Assembly itself is not considered a Firearm under federal law or the National Firearms Act. The ARAK-21 Upper Assembly mounted on
More informationOWNER S MANUAL 12 GA, 20 GA,.410 GA
OWNER S MANUAL General Warnings Be certain this owner s manual is available for reference and is kept with this firearm if transferred to another party. If the manual is lost or misplaced, contact American
More information1911 Pistol. owner s Manual
1911 Pistol owner s Manual IMPORTANT! This manual contains operating, care, and maintenance instructions. To assure safe operation, any user of this firearm must read and understand this manual before
More information/ PISTOL
OWNER S MANUAL 1911-22/1911-380 PISTOL SUPPRESSOR READY Important operating instructions for: BROWNING 1911-22 AND 1911-380 AUTOLOADING PISTOLS If you have any questions or comments regarding your new
More informationNATIONAL PARK SERVICE MANUAL FOR THE HANDLING AND FIRING OF U.S. M1911 and M1911A1 Colt Automatic Pistol,.45 A.C.P. Caliber IN INTERPRETIVE
NATIONAL PARK SERVICE MANUAL FOR THE HANDLING AND FIRING OF U.S. M1911 and M1911A1 Colt Automatic Pistol,.45 A.C.P. Caliber IN INTERPRETIVE DEMONSTRATIONS 1 PREFACE This manual sets forth the procedures
More informationVANGUARD SERIES 2 OWNERS MANUAL
VANGUARD SERIES 2 OWNERS MANUAL INTRODUCTION Thank you for buying a Weatherby firearm, and welcome to the family. We realize that you had many products to choose from and hope you feel as we do, that you
More informationWritten By: Marcus C
Cleaning a Browning BPS Shotgun How to clean the Receiver and Barrel of a Browning BPS Shotgun. Written By: Marcus C ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION This guide will take you
More informationMCMILLAN TAC -50 S H O O T T O W I N
O W N E R S M A N U A L MCMILLAN TAC -50 S H O O T T O W I N Congratulations. You are now the owner of the finest firearm that technology, craftsmanship and art can build. Please take a few minutes and
More informationMODEL 1400 E USER S MANUAL WARNING: READ THE INSTRUCTIONS AND SAFETY PRECAUTIONS IN THIS MANUAL CAREFULLY BEFORE USING THIS FIREARM.
ARMSCOR MODEL 1400 E USER S MANUAL WARNING: READ THE INSTRUCTIONS AND SAFETY PRECAUTIONS IN THIS MANUAL CAREFULLY BEFORE USING THIS FIREARM. DISCHARGING FIREARMS IN POORLY VENTILATED AREAS, CLEANING FIREARMS
More informationMorini CM 22M. Technical Data
Morini CM 22M Technical Data Caliber: Weight: Total Length: Total Height: Total Width: Length of Sight Line: Barrel Length: Number of Riflings: Trigger: 1 st stage weight: 2 nd stage weight: Sight: Sight
More informationBarrel Assembly. Field Stripping
WARNINGS: Carry out safety check before handling the weapon. The weapon is heavily oiled for shipping. Clean and lubricate before firing. These procedures given apply only to the US Ordnance QCB version.
More informationINSTRUCTION MANUAL DEADLINE MADE IN CANADA
INSTRUCTION MANUAL DEADLINE MADE IN CANADA 2 ABOUT The Deadline action is specifically designed for long range, precision shooting. Its components are made using the cutting edge of technology and subject
More informationPISTOL CALIBER AR STYLE FIREARMS
PISTOL CALIBER AR STYLE FIREARMS OWNER'S MANUAL: OPERATION, HANDLING, DISASSEMBLY / REASSEMBLY & SAFETY INSTRUCTIONS - DO NOT DISCARD THIS MANUAL - READ THIS MANUAL CAREFULLY, PAYING CLOSE ATTENTION TO
More informationIn appreciation of their efforts, we would like to dedicate our Pionieer shotgun to them and we are proud to bring it to you.
Dear customer, Thank you for choosing Pioneer a true hammered Cowboy Action Shotgun. Your shotgun is manufactured by PIONEER ARMS CORP. to the highest standards. It has been produced to meet the requirements
More informationHATFIELD. Continuing the Tradition SEMI-AUTOMATIC SHOTGUN INSTRUCTION MANUAL
HATFIELD Continuing the Tradition SEMI-AUTOMATIC SHOTGUN INSTRUCTION MANUAL READ THE INSTRUCTIONS AND WARNINGS IN THIS MANUAL CAREFULLY BEFORE USING THIS FIREARM SAFETY HANDLING RULES 1.Always keep the
More informationMARINE CORPS INSTITUTE INSPECTION AND REPAIR OF THE M9 PISTOL
MARINE CORPS INSTITUTE INSPECTION AND REPAIR OF THE M9 PISTOL MARINE BARRACKS WASHINGTON, DC Table of Contents Page Contents... Navigation Instructions... i iii Chapter 1 Disassembly and Assembly of the
More informationOPERATOR S INSTRUCTIONS for the ARMALITE AR-30 RIFLE
P.O. Box 299 Geneseo IL 61254 Tel 309-944-6939 fax 309-944-6949 armalite@geneseo.net OPERATOR S INSTRUCTIONS for the ARMALITE AR-30 RIFLE August 10, 2002 I. INTRODUCTION Description: Figure 1, The AR-30
More informationAppendix 5 NRA INSTRUCTOR TRAINING PROGRAM PRE-COURSE QUALIFICATION PISTOL
NRA TRAINING COUNSELOR GUIDE Appendix 5: NRA Instructor Training Program Pre-Course Qualification Pistol Appendix 5 NRA INSTRUCTOR TRAINING PROGRAM PRE-COURSE QUALIFICATION PISTOL The NRA Instructor Training
More informationOPERATION INTRODUCTION VARIATIONS
REMINGTON 700 INTRODUCTION Since Remington introduced the Model 700 in 1962, it has become the bestselling line of bolt-action sporting rifles in history.1 The Remington action is renowned for its 3-rings-of-steel
More informationW h i t n ey. Wo l v e r i n e. Owner s Manual. What s old, is new again! Olympic Arms. 624 Old Pacific Hwy SE Olympia, WA 98513
O l y m p i c Whitney A r m s Wolverine W h i t n ey Wo l v e r i n e Serial Number Owner s Manual Olympic Arms What s old, is new again! 624 Old Pacific Hwy SE Olympia, WA 98513 www.olyarms.com (800) 228-3471
More informationAR15/ BCA 10 RIFLE OWNER S MANUAL
AR15/ BCA 10 RIFLE OWNER S MANUAL THIS IS NOT A SAFETY MANUAL. IF YOU NEED ASSISTANCE WITH THE SAFE HANDLING OF THIS, OR ANY FIREARM, PLEASE CONTACT A CERTIFIED FIREARMS INSTRUCTOR OR SCHOOL. Fundamental
More informationSAAMI. Semi-Automatic Assault Shotgun Owner s Manual. Tel. : Fax
Head Quarter Beyşehir Organize Sanayi Bölgesi Bayavşar Mah. 4959 Sk. No.24-42700 Beyşehir - Konya / TURKEY Tel. : +90 332 524 60 32-34 - Fax +90 332 524 62 4 - info@deryaarms.com SAAMI SPORTING ARMS AND
More informationP9S Automatic Pistol Caliber.45 ACP
P9S AUTOMATIC PISTOL Caliber.45 ACP P9S Automatic Pistol Caliber.45 ACP Instruction Manual HECKLER & KOCH, INC. 2148 Pacific Boulevard Sterling, Virginia 20166-8903 U.S.A. TEL. (703) 450-1900 TELEFAX (703)
More informationINSTRUCTION MANUAL CZ 630/631
INSTRUCTION MANUAL CZ 630/631 Before handling the air rifle read this manual carefully and observe the following safety instructions. Improper and careless handling of the air rifle could result in unintentional
More informationDefender Series Owner s Manual
4904 Hwy 98/PO Box 67 Comer, GA 30629 (866) 803-0000 Fax (706-783-5800) Defender Series Owner s Manual MPA1SST & MPA20SST/DMG Carbines MPA10T & MPA10SST Pistols MPA30T & MPA30SST/DMG Pistols When you purchased
More informationREC7 DI OPERATOR S MANUAL
EC7 D REC7 DI OPERATOR S MANUAL TABLE OF CONTENTS 2 2 4 5 6 6 6 8 8 10 11 12 12 13 13 15 18 20 22 USE OF THIS MANUAL SAFETY GUIDELINES WARRANTY AND SERVICE NOTES FUNCTIONS AND FEATURES BREAK IN PROCEDURE
More informationVR60 SHOTGUN USER S MANUAL WARNING: READ THE INSTRUCTIONS AND SAFETY PRECAUTIONS IN THIS MANUAL CAREFULLY BEFORE USING THE FIREARM.
VR60 SHOTGUN USER S MANUAL WARNING: READ THE INSTRUCTIONS AND SAFETY PRECAUTIONS IN THIS MANUAL CAREFULLY BEFORE USING THE FIREARM. SEPTEMBER 2016 ROCK ISLAND ARMORY USER S MANUAL VR60 SHOTGUN SAFETY,
More information;\- ,.. SAFETY WARNING: Failure to obey a safety warning may result In Injury to you or. T to others. T LOADED AND THE SAFETY IS IN THE
,.. SAFETY WARNING: Failure to obey a safety warning may result In Injury to you or T to others. '-"f"oi:ti,., WARNING INSTRUCTIONS FOR THE MODEL 1400 CAUTION-ALWAYS KEEP THE T MUZZLE POINTED IN A SAFE
More informationOwners Manual MAX-11 mk2 Upper Receiver
Owners Manual MAX-11 mk2 Upper Receiver LAGE Manufacturing, L.L.C. 916 E. Baseline Rd. STE #113 Mesa, AZ 85204 CM11-300 NFA Warning This upper receiver is designed to be used with the SWD M-11/9 submachine
More informationTREAT EVERY GUN AS IF IT IS LOADED...ALL THE TIME
Table of Contents Owner s Record...3 Introduction...3 Ammunition...4 Break-in Period...5 Know Your Firearm...6 Right Side...6 Left Side...6 Operation...7 Magazine Loading...7 Magazine Loading with the
More informationCamden Co. Sheriff s Office FIREARMS SAFETY
Camden Co. Sheriff s Office FIREARMS SAFETY Firearms safety is YOUR responsibility! Never completely trust any safety mechanism. No safety mechanism is a substitute for proper weapon handling. Any safety
More informationOWNER S MANUAL FOR OA SERIES FIREARMS
OWNER S MANUAL FOR OA SERIES FIREARMS 620-626 Old Pacific Hwy SE Olympia, WA 98513 (360) 459-7940 WARNING To avoid accidental firing, BE SURE WEAPON IS CLEAR. Failure to do so could result in serious injury
More informationSAR-15 RIFLE OWNERS MANUAL
SAR-15 RIFLE OWNERS MANUAL SIONICS WEAPON SYSTEMS Our mission is to manufacture quality firearms made with pride in the USA. We are able to do accomplish this by using only the best American made parts.
More information2-1. CLEARING PROCEDURES
CHAPTER 2 MAINTENANCE Proper maintenance contributes to weapon effectiveness as well as unit readiness. This chapter discusses the maintenance aspects of the M249 AR to include inspection; cleaning and
More informationM*CARBO Hi-Point Carbine Trigger Spring Kit Download or Print Instructions Contact: Page 1
Download or Print Instructions Contact: help@mcarbo.com Page 1 Step 1: Clear your Firearm - Check the chamber, bolt face and magazine well. Step 3: Using the Hi-Point disassembly tool break the bolt loose
More informationSINGLE-ACTION SMALL-BORE REVOLVER OWNER S INSTRUCTION MANUAL
HERITAGE ROUGH RIDER SINGLE-ACTION SMALL-BORE REVOLVER OWNER S INSTRUCTION MANUAL We recommend that you seek instruction in safe firearm handling by a competent firearms instructor. Remember there is no
More informationThank you for buying Bushmaster
AZ 16010 Before disassembling, loading, or using this firearm, please Read, Understand, and Follow all the instructions in this manual, regarding proper handling and safe use!! Caution: If unfamiliar with
More informationAK63D SEMI-AUTO RIFLE
Owner s Manual AK63D SEMI-AUTO RIFLE Cal. 7.62X39MM Congratulations on your purchase of the AK63D Semi-Auto Rifle. With proper care and handling, it will give you long, reliable service. The AK63D is a
More informationSHF R50 SHF S50 Safety Harbor Firearms, Inc. PO Box 563 Safety Harbor, FL Ph: Fax:
SHF R50 SHF S50 Safety Harbor Firearms, Inc. PO Box 563 Safety Harbor, FL 34695-0563 Ph: 727-726-2500 Fax: 727-797-6134 www.safetyharborfirearms.com 1 ^ WARNING Risk of serious injury or death. Failure
More informationUSER MANUAL Tisas Pistols
USER MANUAL Tisas Pistols ZiG M45 (.45 ACP Single Action) ZiG PC1911 (.45 ACP Single Action) ZiG PCS1911 (.45 ACP Single Action) ZiG PCS9 (9 x19 Single Action) Zenith Firearms Come Shoot the Quality WARNING
More informationINTRODUCTION. Good Shooting! -1-
INTRODUCTION Thank you for buying a Weatherby firearm, and welcome to the family. We realize that you had many products to choose from and hope you feel as we do, that you purchased the finest quality
More informationTABLE of CONTENTS. Safety 4. Introduction 6. Description 6. Storage 6. Components 7. Unloading and Inspection 8. Disassembly 10. Care and Cleaning 12
1911 Pistol Manual 2 TABLE of CONTENTS Safety 4 Introduction 6 Description 6 Storage 6 Components 7 Unloading and Inspection 8 Disassembly 10 Care and Cleaning 12 Loading and Firing 13 Troubleshooting
More informationSHOOTERS ARMS SEMI-AUTO PISTOLS
Owner s Manual SHOOTERS ARMS SEMI-AUTO PISTOLS Cal..45 ACP Congratulations on your purchase of a Shooters Arms Semi-Auto Pistol. With proper care and handling, it will give you long, reliable service.
More informationINSTRUCTION MANUAL CZ 452/453
INSTRUCTION MANUAL CZ 452/453 Before handling the firearm read this manual carefully and observe the following safety instructions. Improper and careless handling of the firearm could result in unintentional
More informationBeeman Precision Airguns Spring-Piston Air Rifles P1, P3, P11
Beeman Precision Airguns Spring-Piston Air Rifles P1, P3, P11 User Instruction Manual V1 10/17 CONTENTS Rules of safe shooting...3 Cocking & Loading... 4 Safety... 4 Sight Adjustment...5 Trigger Adjustment...5
More informationOperator s Manual for P7 Series Pistols
Operator s Manual for P7 Series Pistols P7PSP, P7M8 & P7M13 9mm x 19 P7M10 Caliber.40 S&W WARNING: A firearm has the capability of taking your life or the life of someone else! Be extremely careful with
More informationINTRODUCTION STRIKER SYSTEM ORIGINS OF P320 SAFETY
SIG SAUER P320 INTRODUCTION Sig Sauer has a longstanding reputation for excellence in service handguns. The popular P220 series was at the head of the class when steel-framed double-action pistols were
More informationBiggest Finest Revolver
Print 11/18/03 8:29 AM Page 1 INSTRUCTION MANUAL FOR MAGNUM S BFR Biggest Finest Revolver STAINLESS STEEL SINGLE ACTION REVOLVER * Shown with optional Hogue grip. READ THE INSTRUCTIONS AND WARNINGS IN
More informationBefore handling the firearm read this manual carefully and observe the following safety instructions. CONTENTS
Before handling the firearm read this manual carefully and observe the following safety instructions. Improper and careless handling of the firearm could result in accidental discharge and cause injury,
More information