Owners Manual Models 4430BF3, 4430BF2 & 4430BF1 Floor Mounted Tri-Level Bottle Filling Tubular Fountain

Transcription

1 Owners Manual Models 4430F3, 4430F2 & 4430F1 Floor Mounted Tri-Level ottle Filling Tubular Fountain MODEL 4430F1L MODEL 4430F2UM INSTALLER 4430F Fountains are among the easiest to install Fountains on the market today. To assure you install these models easily and correctly, PLEASE READ THESE SIMPLE INSTRUTIONS EFORE STARTING THE INSTALLATION. HEK YOUR INSTALLATION FOR OMPLIANE WITH PLUMING, ELETRIAL, AND OTHER APPLIALE ODES. After installation, leave these instructions with the Fountain for future reference. IMPORTANT ALL SERVIE TO E PERFORMED Y AN AUTHORIZED SERVIE PERSON IMPORTANT! INSTALLER PLEASE NOTE. MODEL 4430F3 THE GROUNDING OF ELETRIAL EQUIPMENT SUH AS TELEPHONE, OMPUTERS, ET. TO WATER LINES IS A OMMON PROEDURE. THIS GROUNDING MAY E IN THE UILDING OR MAY OUR AWAY FROM THE UILDING. THIS GROUNDING AN AUSE ELETRIAL FEEDAK INTO A FOUNTAIN, REATING AN ELE- TROLYSIS WHIH AUSES A METALLI TASTE OR AN INREASE IN THE METAL ONTENT OF THE WATER. THIS ONDITION IS AVOIDALE Y USING THE PROPER MATERIALS AS INDIATED. ANY DRAIN FITTINGS PROVIDED Y THE INSTALLER SHOULD E MADE OF PLASTI TO ELETRIALLY ISOLATE THE FOUNTAIN FROM THE UILDING PLUMING SYSTEM. PAGE (Rev. - /)

2 O " 305mm.. O 1/2" 13mm HOLES (6 PL) O 10" 254mm O 14" 356mm 48" 19mm 64" 1626mm 57" 1448mm 30" 762mm 37" 940mm 27" 686mm 1-1/2" DRAIN A 8" 203mm 7 /16" 201mm FINISHED FLOOR LEGEND A = 3/8" O.D. UNPLATED OPPER TUE ONNET - SHUT OFF VALVE Y OTHERS = AESS PANEL ( 8" X 10" ) = REMOVALE OTTOM OVER 52 1/8" 13mm 44" 1118mm 22 1/8" 562mm 32 1/8" 816mm 4430F (Rev. - /) PAGE 2

3 O " 13mm 305mm.. O 1/2" HOLES (6 PL) O 10" 254mm O 14" 356mm 48" 19mm 57" 1448mm 41 9/16" 1056mm ORIFIE HEIGHT 52 1/8" 13mm 30" 762mm 37" 940mm 40 5/16" 10mm 27" 686mm 1-1/2" DRAIN A 22 1/8" 562mm 32 1/8" 816mm 8" 203mm 7 /16" 201mm FINISHED FLOOR ATUAL PRODUT ONFIGURATION MAY VARY ASED ON MODEL ORDERED. LEGEND A = 3/8" O.D. UNPLATED OPPER TUE ONNET - SHUT OFF VALVE Y OTHERS = AESS PANEL ( 8" X 10" ) = REMOVALE OTTOM OVER 4430F2ML PAGE (Rev. - /)

4 O " 13mm 305mm.. O 1/2" HOLES (6 PL) O 14" 356mm 48" 19mm 44" 1118mm 64" 1626mm 30" 762mm 34 7/16" 875mm ORIFIE HEIGHT 33 5/16" 846mm 1-1/2" DRAIN A 28 7/16" 7mm 29 3/4" 756mm ORIFIE HEIGHT 27" 686mm 22 1/8" 562mm 8" 203mm 7 /16" 201mm FINISHED FLOOR ATUAL PRODUT ONFIGURATION MAY VARY ASED ON MODEL ORDERED. LEGEND A = 3/8" O.D. UNPLATED OPPER TUE ONNET - SHUT OFF VALVE Y OTHERS = AESS PANEL ( 8" X 10" ) = REMOVALE OTTOM OVER O 10" 254mm 4430F1U (Rev. - /) PAGE 4

5 1. This fountain is to be mounted on a smooth, flat, finished surface with adequate support structure. NOTE: Mounting structure must be capable of supporting 300 lb. load on fountain. 2. Refer to rough-in for plumbing. 3. Install shut-off valve on water supply. (Valve not furnished) 4. Locate and install fountain using 3/8" minimum screws or bolts, (Screws or bolts not furnished). 5. Prior to installing the bottle filler to the center mounting position of fountain, insert drain pipe (Item #10) by positioning the short end of drain pipe through mounting plate of bottle filler. Install bottle filler to fountain and secure with supplied hardware. 6. Prior to installing the bottle to the arm mount of fountain, insert the drain pipe (Item #11) into the arm tunnel and adjust drain to lean to the left side of the arm when facing the button. Install bottle filler to arm being sure drain tube is above mounting plate of filler. Secure filler to fountain with supplied hardware. 7. onnect fountain to supply line with a shut-off valve and install a 3/8" unplated copper water line between the valve and the cooler. Remove any burrs from outside of water line. Push the tubes straight into the fittings until they reach a positive stop, approximately 3/4" (See Fig. 2). DO NOT SOLDER TUES INSERTED INTO PLASTI FITTINGS AS DAMAGE TO THE O-RINGS MAY RESULT. 8. Water supply 3/8" O.D. unplated copper tube. Waste 1-1/2" IPS. ontractor to supply waste trap and service stop valve in accordance with local code. 9. onnect water supply and fountain drain. onnect drain waste "Tee" to fountain drain tubes. onnect outlet of "Tee" to drainage system. Water connection and drain must comply with local codes. 10. Turn on water supply and check all connections for leaks. Threaded drain fittings may require thread sealer to create a leak free connection. Apply thread sealer to threaded connection fittings only, not the slip connection fittings. AUTION: This fountain is rated for inlet water pressure of PSI. A pressure reducing regulator should be used if the inlet water supply exceeds 105 PSI. Any damage caused by reason of connecting this product to supply line pressures lower than 20 psig or higher than 105 psig is not covered by warranty. 11. onnecting lines to be made of unplated copper and should be thoroughly flushed to remove all foreign matter before being con nected to fountain. This fountain is manufactured in such a manner that it does not in any way cause taste, odor, color, or sediment problems. TROULE SHOOTING AND MAINTENANE Actuation of Quick onnect Water Fittings: Fountain is provided with lead-free connectors which utilize an o-ring water seal. To remove tubing from the fitting, relieve water pressure, push in on the gray collar while pulling on the tubing.(see Fig.2) To insert tubing, push tube straight into fitting until it reaches a positive stop, approximately 3/4". FIG. 2 FIG. 3 1/4" O.D. TUE WATER INLET TO OOLER FIG. 1 3/8" O.D. UNPLATED OPPER TUE ONNET OLD WATER SUPPLY UILDING WATER INLET NOTE: WATER FLOW DIRETION SERVIE STOP (NOT FURNISHED) STREAM HEIGHT ADJUSTMENT: Stream height is factory set at 35 PSI. If supply pressure varies greatly from this, insert a small straight bladed screwdriver through the access hole in the center of the push button and turn the adjustment screw. lockwise adjustment will raise the stream and counterclockwise adjustment will lower the stream. For best adjustment, the stream should be approximately 1 1/2" above the top of the bubbler. (See Fig. 3) PAGE (Rev. - /)

6 14 & 2 & 19 & & or or or (Rev. - /) PAGE 6

7 ITEM NO ITEMIZED PARTS LIST PART NO. DESRIPTION P asin over - Round Plate Tailpipe Drain Plug 1-1/2" Access Panel ottom over Drain Tube In - Line Strainer Drain Tube Tube - Drain Tube - Drain (Arm Only) ubbler Assembly Kit - Regulator W/Spring Kit - "O" Rings and Fittings Kit - Gasket Kit GPM Regulator (F Only) Kit - Nozzle Kit - Aerator Kit - ottle Filler Trim Kit - Push utton Kit - Plastic Drain Kit - 90 Plastic Drain Kit Series Hardware Kit - ottle Filler Waterway Aerator Outdoor ottle Filler Drain Plug See Fig FIG. 4 PRINTED IN U.S.A. FOR PARTS ONTAT YOUR LOAL DISTRIUTOR OR ALL PAGE (Rev. - /)

8 THIS PAGE WAS LEFT INTENTIONALLY LANK (Rev. - /) PAGE 8