Product Standard and Inspection Criteria for ilmasil PS Clear Fused Quartz Tubes
|
|
- Edwin Horn
- 6 years ago
- Views:
Transcription
1 Product Standard and Inspection Criteria for Page 1 of 5 Version S Index: C (June 2015) Application: This standard is applicable to direct drawn tubes produced with ilmasil PS base material 1 Optical Properties 1.1 Transmission Guaranteed values Wavelength λ [nm] wallthickness 1 mm 80% 84% 89% 90% 91% 91% wallthickness 1,5 mm 75% 82% 89% 90% 91% 91% wallthickness 2 mm 70% 80% 89% 90% 91% 91% Typical Transmission for UV range Remarking: All values are valid for measurement on a flat surface. Measurements on tube surface may vary depending on the tube diameter QSIL GmbH Quarzschmelze Ilmenau Gewerbering Langewiesen / Germany Page: 1/5
2 Page 2 of 5 Version S Index: C (June 2015) 2 Hydroxyl Content (OH-content) Remark: degree of hydroxyl groups in the tube wall (excluding outer surface) The typical content in ilmasil PS fused quartz tubes is 10 ppm max. 15 ppm After thermal treatment, a decrease of maximum 3 ppm is obtainable by tempering the material at 1000 C under vacuum for a period of 30 hours. 3 Visual Characteristics The term visual is used for the inspection method where the tubing to be inspected at a distance of m from the inspector, with a white/black background under general inspection illumination Bubbles Enclosed Bubbles a spherical void, wholly within the tube wall Tube outer diameter (OD) 40 mm and/or wallthickness (wt) 4 mm Bubble Length Bubble Width Max. number per 100 mm tube length [pcs] Sum of length of all bubbles per 100 mm tube length wt 1 mm mm wt > 1 2 mm mm wt >2-4 mm mm Bubbles less than < 0.3 mm diameter are not counted. Bubble clusters: Judge the whole cluster to the limits of a single bubble; Bubble clusters > 5 mm are QSIL GmbH Quarzschmelze Ilmenau Gewerbering Langewiesen / Germany Page: 2/5
3 Page 3 of 5 Version S Index: C (June 2015) Tube dimensions OD 40 mm und wt > 4 mm and Tube dimensions OD > 40 mm Bubbles in length < 0.3 mm are not counted Bubbles in length > 5 mm Bubbles in width > 0.2 mm Total cross sections of all bubbles: max. 30 mm²/100cm³ (as per DIN 58927) Open Bubbles A void, open to the wall surface None allowed on the ID or OD (visual detection limit: 0.1 mm) Bubble Clusters More than one bubble connected Judge the whole cluster to the limits of a single bubble 3.2 Inclusions included foreign particles (spots), visible by color difference inclusions in diameter > 0.1 mm are for detection of white spots use a black background for detection of black spots use a white background 3.3 Striation transparent inclusions, causing apparent optical distortion scattered colorless striations are permitted Colored striations are visual on a crosswalk-background. QSIL GmbH Quarzschmelze Ilmenau Gewerbering Langewiesen / Germany Page: 3/5
4 Page 4 of 5 Version S Index: C (June 2015) 3.4 Surface defects Scratches a fine line abrasion on outer surface (line wider as 0.1 mm) visible by unaided eye with a black background permitted if not perceptible with gloved fingers visual, manually, caliper, scale magnifier Scuff Limits: broad surface abrasion (groups of lines wider as 0.1 mm). visual, caliper Waterspots, Fingerprints, Cutter dust removable surface deposits left by washing residue or finger touch permitted to a minor degree visual Vapor Limits: a broad area or band of white haze on the inner or outer surface visual on a black background Structure Optical distortion caused by marginal variations in the wall thickness permitted if low-contrast appearance (comparison with limit sample) visual QSIL GmbH Quarzschmelze Ilmenau Gewerbering Langewiesen / Germany Page: 4/5
5 Page 5 of 5 Version S Index: C (June 2015) Bubble Scars Depressions on the surface caused by healed or collapsed bubbles visual (inspection to be performed in axial direction) Surface adhesions non-colored quartz particles fused into the surface causing a protrusion if any sharp edges visual, manually 4 Further applicable documents S Specification and Inspection Criteria for Tubes: Dimensional Characteristics S PS Material Standard: Clear Fused Quartz ilmasil PS QSIL GmbH Quarzschmelze Ilmenau Gewerbering Langewiesen / Germany Page: 5/5
MIL-STD-883H METHOD EXTERNAL VISUAL
* EXTERNAL VISUAL 1. PURPOSE. The purpose of this test method is to verify the workmanship of hermetically packaged devices. This test method shall also be utilized to inspect for damage due to handling,
More informationUnderwater Fiber-Optic Plane Irradiance Collector
Underwater Fiber-Optic Plane Irradiance Collector User s Manual Revision F, October 2018 Hōbi Instrument Services www.hobiservices.com Revisions F October 2018, improved illustrations, table of immersion
More informationVisual Inspection of Medicinal Products for Parenteral Use
Good Practice Paper Visual Inspection of Medicinal Products for Parenteral Use Version 1.0 (September 2014) Version 1.0 1 (16) Acknowledgement This ECA Good Practice Paper was developed by the Steering
More informationThe Agility Association of Canada
Check list to Prepare for Equipment Inspection 2018 Introduction: requires that all equipment used at sanctioned events be inspected and approved at least four months before a host s first trial, and regularly
More informationPETERSEN 161-SERIES HIGH PRESSURE LIFTING AIR BAGS OPERATING INSTRUCTIONS WARNING!
PETERSEN 161-SERIES HIGH PRESSURE LIFTING AIR BAGS OPERATING INSTRUCTIONS WARNING! Read and understand instructions before using Petersen Plugs. Failure to comply may result in property damage, serious
More informationFiber Optic Splice Closures
Fiber Optic Splice Closures . Products Descriptions of Optical Closure and Splice Tray FOCSS FOCS FOCM Splice Tray-2C Splice Tray-24C Dimensions (mm): 225(l) 08(w) 2(h) Dimensions (mm): 68(l) 9(w) 9(h)
More informationPolarimeter tubes and accessories
Polarimeter tubes and accessories Opto-electronic measuring device since 1864 Polarimeter tubes of SCHMIDT+HAENSCH are designed for different applications. All tubes meet the ICUMSArecommendations, class
More informationSupratec AERATION TECHNOLOGY. von-drais-straße 7 D Simmern / Hunsrück. tel.: / fax: /
PERMOX OM120 Oval Membrane Tu b e D i ffuser w i th stainless steel b o d y Supratec for fine bubble or coarse bubble diffusion of liquids Supratec UND GESELLSCHAFT FÜR UMWELT- VERFAHRENSTECHNIK MBH AERATION
More informationNovelBright LED Illuminator
NovelBright LED Illuminator Instruction Manual version NS01_11 Instruction Manual This LED illuminator is suitable for research use only. It must be used by specialized personnel that know the health risks
More informationIntroduction. Terms of reference. Technical Leaflet T5: The Net Gauge BoD Approval: 2014
Introduction At present, net gauges are not applicable equipment for approval by ITTF. Nevertheless net gauges have a very important role to keep the matches fair such that: (i) the result of a rally should
More informationREGULATIONS OF TOURNAMENT 2018 Crossminton for all age-groups
REGULATIONS OF TOURNAMENT 2018 Crossminton for all age-groups Editor - International Crossminton Organisation - Revised version: 2018, JAN. by FRANKE 1/6 Content: Explanation of concepts... 3 A Basic conditions...
More informationPressure maintenance valve SDV-P / SDV-P-E
Translation of the original manual Pressure maintenance valve SDV-P / SDV-P-E Assembly and Operating Manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains the copyrighted
More informationCustomer Information Bulletin
3D Production Printers Advisory Upgrade / Repair / Retrofit Safety Alert Purpose: Tips and Info Accura Bluestone Material Accura Bluestone Material Tips and Info - Accura Bluestone Material 1. Each material
More informationi-clicker Discussion Question
PHY132 Introduction to Physics II Class Class 3 Outline: Outline: Ch. 21, sections 21.1-21.4 The Principle of Superposition Standing Waves Nodes and Antinodes Musical Instruments QuickCheck 1.1 i-clicker
More informationOperating manual Analogue Brix Refractometer
KERN & Sohn GmbH Ziegelei 1 D-72336 Balingen, Germany E-mail: info@kern-sohn.com Operating manual Analogue Brix Refractometer Tel: +49-[0]7433-9933-0 Fax: +49 (0)7433-9933-149 Internet: www.kern-sohn.com
More informationTECH TIPS: ROPE DEFECTS
Hoist Ropes: Why must they be inspected? A hoist rope is not made to last forever. This is a useful fact, as the kinds of wear that appear on a rope can indicate areas of problems within an installation
More informationBackground Statement for SEMI Document 5424A LINE ITEMS REVISION TO SEMI M , SPECIFICATIONS FOR SILICON EPITAXIAL WAFERS
Background Statement for SEMI Document 5424A LINE ITEMS REVISION TO SEMI M62-0912, SPECIFICATIONS FOR SILICON EPITAXIAL WAFERS Notice: This background statement is not part of the balloted item. It is
More informationP-04 Stainless Steel Corrugated Hoses and Metal Bellows Expansion Joints
Guideline No.P-04 (201510) P-04 Stainless Steel Corrugated Hoses and Metal Bellows Expansion Joints Issued date: 20 th October 2015 China Classification Society Foreword This Guideline is a part of CCS
More informationTechnical Note. Determining the surface tension of liquids by measurements on pendant drops
Technical Note Pendant Drop Measurements Technical note: TN316e Industry section: all Author: FT, TW Date: 12/2010 Method: Drop Shape Analyzer DSA100 Keywords: Methods, surface tension, interfacial tension,
More informationWaves. Kevin Small or
Waves Opening note: X-rays can penetrate your body. Sound waves can make thinks vibrate; water waves can knock you over in the sea. Infrared waves can warm you up and slinky waves are fun to play with.
More informationMANUAL SEALLESS STEEL STRAPPING TOOL MODEL A
OPERATION MANUAL / SPARE PARTS LIST MANUAL SEALLESS STEEL STRAPPING TOOL MODEL A337.0001 13.1912.01 13191201.en/MAS/ 10.02 INDEX PAGE 1 SAFETY INSTRUCTIONS 2 2 WARRANTY CONDITIONS AND LIABILITY 4 3 APPROPRIATE
More informationDETERMINATION OF THE DEPTH OF CLOSED BLIND CRACKS IN NON-METAL CHECK SAMPLES AND TEST PANELS FOR PENETRANT TESTING
DETERMINATION OF THE DEPTH OF CLOSED BLIND CRACKS IN NON-METAL CHECK SAMPLES AND TEST PANELS FOR PENETRANT TESTING Nikolay Kalinichenko 1, Aleksey Kalinichenko 1, Irina Lobanova 1*1, Anna Zaitseva 1, Egor
More informationLED AND LIGHTING PROFILES AND TUBES
LED AND LIGHTING PROFILES AND TUBES INDEX PRODUCTS PROFILES Page 0-10 8-9 10-20 10-20 20-30 21-34 30-40 38-43 40-50 46-50 50-60 51-54 60-70 55-56 70-80 57 80-90 60 90-100 61 100-120 64 120-275 65-66 MICRO
More informationPLASTIC PROFILES AND TUBES
PLASTIC PROFILES AND TUBES INDEX PRODUCTS PROFILES Page 0-10 8-9 10-20 10-20 20-30 21-34 30-40 38-43 40-50 46-50 50-60 51-54 60-70 55-56 70-80 57 80-90 60 90-100 61 100-120 64 120-275 65-66 MICRO PRISMATIC
More informationFiltration FILTRATION PRODUCT TIPS
Filtration 195 18 Proved and tested, durable, optimally resistant against acids, caustic solutions and other aggressive chemicals: our solutions for efficient and safe filtration. PRODUCT TIPS BOLA Filtration
More information1 SE/P-02. Experimental and Analytical Studies on Thermal-Hydraulic Performance of a Vacuum Vessel Pressure Suppression System in ITER
1 SE/P-2 Experimental and Analytical Studies on Thermal-Hydraulic Performance of a Vacuum Vessel Pressure Suppression System in ITER K. Takase 1), H. Akimoto 1) 1) Japan Atomic Energy Research Institute,
More informationSupplementary Installation and Operating Instructions. Variable Area Flow Meters SGK-1 Ex SGK-2 Ex SGK-3 Ex. Category: II 2G Ex IIC II 3G Ex IIC
Supplementary Installation and Operating Instructions Variable Area Flow Meters SGK-1 Ex SGK-2 Ex SGK-3 Ex Category: II 2G Ex IIC II 3G Ex IIC Contents 1 General safety directions...3 2 Main safety features...4
More informationInsert Ring. Protection Ring from Tube Deformation. Protect tubes from deformation. Ultra soft tube is connectable to Fitting.
http://www.pisco.co.jp TUBE MAKE-TO-ORDER PRODUCTS Protection Ring from Deformation Insert Ring 668 Protect tubes from deformation. Ultra soft tube is connectable to Fitting. Necessary for the connection
More information(1) Name of tube (2) Tube dia. (O.D./I.D.) (3) Tube length. (4) Tube color. Model UD0425. UD1290 O.D. I.D. (mm) UD1075 UD0860 UD
The polyurethane tube, featuring excellent flexiblity, helps compact piping requiring small bending radius. The useful cut marks at 500mm interval are printed on the tube. Model UD0425 UD0640 UD0860 UD1075
More informationResistant. Comfortable. Ergonomic
Comfortable The patented SoftPad frame stems (for the Cube, Cube Orange and Stretch models) offer greater protection, stability and adaptability to the face and can be adjusted to three different lengths.
More informationTHE INNER WORKINGS OF A SIPHON Jacques Chaurette p. eng. January 2003
THE INNER WORKINGS OF A SIPHON Jacques Chaurette p. eng. www.lightmypump.com January 2003 Synopsis The objective of this article is to explain how a siphon works. The difference between low pressure, atmospheric
More informationRow / Distance from centerline, m. Fan side Distance behind spreader, m 0.5. Reference point. Center line
1 Standardisation of test method for salt spreader: Air flow experiments Report 7: Effect of crosswind on salt distribution by Jan S. Strøm, Consultant Aarhus University, Engineering Centre Bygholm, Test
More informationInstruction Manual. Pipe Friction Training Panel
Instruction Manual HL 102 Pipe Friction Training Panel 100 90 80 70 60 50 40 30 20 10 HL 102 Instruction Manual This manual must be kept by the unit. Before operating the unit: - Read this manual. - All
More informationVacuum Science Techniques and Applications Dan Dessau Adv. Lab 2007
Vacuum Science Techniques and Applications Dan Dessau Adv. Lab 2007 Vacuum increases the mean-free-path of gas molecules. Vacuum prevents chemical reaction. Vacuum removes contaminants from surfaces. Vacuum
More informationSPECIFICATIONS PARTICLE SENSOR KS-18F Higashimotomachi, Kokubunji, Tokyo , Japan
SPECIFICATIONS PARTICLE SENSOR KS-18F 3-20-41 Higashimotomachi, Kokubunji, Tokyo 185-8533, Japan No. 05083-5E 18-01 Printed in Japan Outline The KS-18F is a sensor which uses the light scattering method
More informationBasic & Controlled Atmosphere Glove Boxes
I N T R O D U C T I O N Precise Basic and Controlled Atmosphere Glove Boxes provide a leak-tight environment for work with contamination-sensitive materials. Precise Basic Glove Boxes are simple, economical
More informationSupratec Gesellschaft für Umweltund Verfahrenstechnik mbh OXYFLEX - M T / M T M E M B R A N E D I S C D I F F U S ER AERATION TECHNOLOGY
OXYFLEX - M T 2 3 5 / M T 3 0 0 M E M B R A N E D I S C D I F F U S ER UND GESELLSCHAFT FÜR UMWELT- VERFAHRENSTECHNIK MBH AERATION TECHNOLOGY von-drais-straße 7 D-55469 Simmern / Hunsrück Tel.: +49 6761
More informationTube Cutter with Measuring tape built-in
http://www.pisco.co.jp TUBE MAKE-TO-ORDER PRODUCTS Cutter with Measuring tape built-in 658 Series Cutter TUBE VALVE CONTROLLER FITTING Model Code of Cutter (Example) Cutter Model Code of Cutter Blade (Example)
More informationTHE ARENA TABLE OF CONTENTS 6 THE ARENA OVERVIEW Dimensions and Tolerances... 2
Section 6 THE ARENA TABLE OF CONTENTS 6 THE ARENA... 2 6.1 OVERVIEW... 2 6.1.1 Dimensions and Tolerances... 2 6.2 PLAYING FIELD... 4 6.2.1 Boundaries and Markings... 4 6.2.2 The RACK... 5 6.3 GAME PIECES...
More informationFRIGOFLEX is an innovative system designed for the conveyance of R134, R404, R407, R410 refrigerant gases and other specific fluids.
FRIGOFLE is an innovative system designed for the conveyance of R14, R404, R407, R410 refrigerant gases and other specific fluids. This system consists of a flexible multilayered polymeric pipe and a series
More informationOperating manual Analogue refractometer
KERN & Sohn GmbH Ziegelei 1 D-72336 Balingen, Germany E-mail: info@kern-sohn.com Operating manual Analogue refractometer KERN ORA 1 SA Seawater salinity ORA 2 SA NaCL% ORA 3 SA NACL% Brix% Tel: +49-[0]7433-9933-0
More informationSEMFEW205 - SQA Unit Code H1VP 04 Joining materials by the manual MIG/MAG and other continuous wire processes
Joining materials by the manual MIG/MAG and other continuous wire Overview This unit identifies the competencies you need to prepare and operate manual MIG, MAG or cored-wire arc welding equipment, in
More informationDisc diffuser ELASTOX -T
Pioneering for You Series documentation version 12/2016 2 Application ƒƒfor fine-bubble compressed air aeration within the biological treatment stage ƒƒdepending on application and basin geometry: Use
More informationHigh flow rate. Cost effective. Compliant. Gripper with GSW-B Shaft Interface and Compensation Unit
GSW-B-AGE High flow rate. Cost effective. Compliant. Gripper with GSW-B Shaft Interface and Compensation Unit PGN-plus / PZN-plus universal gripper with shaft interface GSW-B and AGE compensation unit
More information// ADapters GUIDelines
// ADapters GUIDelines ADAPTER SELECTION Selection of an appropriate ALFAGOMMA adapter for a given application depends on the fluid system operating parameters listed below and the tube material and wall
More informationBubble Viscometers A5-A1 / A-T / U-Z6 / Z7-Z10
Measure what you see. Bubble Viscometers A5-A1 / A-T / U-Z6 / Z7-Z10 Manual A member of Additives & Instruments Bubble Viscometers A5-A1 / A-T / U-Z6 / Z7-Z10 Manual English PV-0500 Series PV-0600 Series
More informationSUPER BLUE INSTRUCTIONS FOR TRIMMING AND INSTALLING ORIGINAL NETS WITH STRIPES
Featuring STRIPENET anti-marking, anti-static nets 0056 DEALER, REV. 01/04 PAGE 1 INSTRUCTIONS FOR TRIMMING AND INSTALLING ORIGINAL NETS WITH STRIPES Super Blue and Super Blue 2 and StripeNet are registered
More informationSample Procurement Specifications for Aluminum Traffic Control Signs and Components
Sample Procurement Specifications for Aluminum Traffic Control Signs and Components These sample procurement Specifications were prepared by the American Traffic Safety Services Association (ATSSA) Sign
More informationMounting and Operating Instructions EB 3007 EN. Self-operated Pressure Regulators. Differential Pressure Regulators (opening) Type Type 42-25
Self-operated Pressure Regulators Differential Pressure Regulators (opening) Type 42-20 Type 42-25 Type 42-20 Differential Pressure Regulator Type 42-25 Differential Pressure Regulator Mounting and Operating
More informationApplication of Flex-Z release agent with a pneumatic gun
Application of Flex-Z release agent with a pneumatic gun Manual for spray-gun Granudan ApS Knud Bro Alle 4 DK-3650 Stenloese Denmark www.granudan.com www.granudan.cn Application of Release agent (Flex-Z)
More informationQ/A PROTOCOL FOR THE DAYA BAY 4-METER ACRYLIC VESSELS
Q/A PROTOCOL FOR THE DAYA BAY 4-METER ACRYLIC VESSELS August 27, 2008 Revision 1.0 Abstract A Q/A plan for the construction and delivery of the 4m acrylic vessels (AV s) for the Daya Bay neutrino experiment
More informationWafer Check Valve. Contents. User s Manual. (1) Be sure to read the following description of our product warranty 1
Serial No. H-V066-E-3 Wafer Check Valve User s Manual Contents (1) Be sure to read the following description of our product warranty 1 (2) General operating instructions 2 (3) General instructions for
More informationDichtomatik O-Ring Handbook
Dichtomatik O-Ring Handbook THE DICHTOMATIK O-RING HANDBOOK Editor: Dan Visscher Assistant Editor: Matt Gadlage Design: William Leidenthal Special thanks to the Dichtomatik associates and customers who
More informationRimage Everest 600 Thermal Retransfer Printer
Rimage Everest 600 Thermal Retransfer Printer Superior Print Technology: Superior Results CONTENTS I. Overview II. Printer Comparison III. Print Modes IV. Advantages of Thermal Retransfer Printing V. Printer
More informationTranslation of the original Operating Instructions for HKS rubber compensators
Because of their flexible elements and mechanisms, HKS rubber compensators are susceptible to damage of all types and adverse loads in operation. For reliable operation of a compensator and, thus, the
More informationTube for Clean Environment Polyurethane Tube Clean-Room Package
http://www.pisco.co.jp TUBE MAKE-TO-ORDER PRODUCTS for Clean Environment Polyurethane Clean-Room Package 642 Fine Flexibility. Suitable for Small Bending Radius in General Pneumatic Piping. Cleaned and
More informationDEPARTMENT OF DEFENSE TEST METHOD VISUAL INSPECTION GUIDE FOR RUBBER ELASTROMERIC O-RINGS AMSC N/A FSC 5330
NOTE: MIL-STD-413 has been redesignated as a Test Method Standard. The cover page has been changed for Administrative reasons. There are no other changes to this Document. MIL-STD-413C 8 DECEMBER 1980
More informationPush-In Fitting Type with Stop Valve
http://www.pisco.co.jp Push-In Fitting Type with Stop Valve 278 Push-In Fitting Type with Stop Valve for General Pneumatic Piping. Air Stop by Tube Disconnection. Easy Insertion and Disconnection by Double-passage
More informationGAR-BRO BUCKET LIFTING BAIL INSPECTION RECOMMENDATIONS G & R SERIES BUCKETS
GAR-BRO BUCKET LIFTING BAIL INSPECTION RECOMMENDATIONS G & R SERIES BUCKETS The following are recommendations regarding GAR-BRO bucket bail inspection and wear limits. The details which follow are for
More informationThe Powerful Sealing Calculation
KLINGER expert 6.0 The Powerful Sealing Calculation The KLINGER expert 6.0 gasket design program is a versatile software to assist users in the selection of non-metallic gasket materials. www.klinger.co.at
More informationCoiling Tube Series. Coiling Tube for General Pneumatic Piping. Coiling Tube for General Pneumatic Piping. Suitable for Air Gun or Air Driver.
http://www.pisco.co.jp TUBE MAKE-TO-ORDER PRODUCTS Coiling for General Pneumatic Piping Coiling Series 620 Coiling for General Pneumatic Piping. Suitable for Air Gun or Air Driver. Less Stress on Fittings
More informationRepair instructions. Pivot bushing replacement. XL-AS10001RM-en-DE Rev B
Repair instructions Pivot bushing replacement XL-AS10001RM-en-DE Rev B Table of contents Table of contents 1 General information... 3 1.1 Safety information...3 1.2 Legal information...4 1.3 Order and
More informationCellular Gas Filters DF 100. Product Information
Cellular Gas Filters DF 100 Product Information Reserve technical changes! Reprint not permitted! Table of Contents Application, Features, Technical Data 4 Application 4 Features 4 Technical Data 5 Design
More informationSiphon vessel / Priming aid
Manufacturer: sera GmbH sera-straße 1 34376 Immenhausen Germany Tel.: +49 5673 999-00 Fax: +49 5673 999-01 info@sera-web.com Keep the operating manual for future use! Record the exact type and serial number
More informationLaser-Induced Bubbles in Glycerol-Water Mixtures
Laser-Induced Bubbles in Glycerol-Water Mixtures Allison R. McCarn, Erin M. Englert, and Gary A. Williams Department of Physics and Astronomy, University of California, Los Angeles, California 90095, USA
More informationProduct outline. Titel. BBC-big bubble curtain. Revision: 12/10/2018
Product outline Titel Revision: 12/10/2018 Contents 1. Scope 2 2. Concept 3 3. The Jäger Mare Solutions BBC - Big Bubble Curtain - single or multiple laying principle 4 Since 1942 application-oriented
More informationInstallation, Operation and Maintenance Manual for Back Pressure Regulator
Installation, Operation and Maintenance Manual for Back Pressure Regulator Model 8860 2009 Groth Corporation IOM-8860 Rev. B 12541 Ref. ID: 95565 Page 2 of 13 Table of Contents I. INTRODUCTION 3 II. DESIGN
More informationInvestigation of changes of the refractive index of glass fragments caused by laser ablation
Investigation of changes of the refractive index of glass fragments caused by laser ablation Dr. Stefan Becker Bundeskriminalamt, Forensic Science Institute Wiesbaden, Germany Investigation of changes
More informationCautions : 1. Be careful when you release the Stop Fitting with some internal pressure
The flow-shut mechanism will operate to stop the air flow when the tube is disconnected and will allow air flow when the tube is connected. The double-passage structure facilitates easy connection and
More informationOperating Instructions in compliance with Pressure Equipment Directive 2014/68/EU. FAS Manual Brass Shut-Off Valve DN10 through DN22
Operating Instructions in compliance with Pressure Equipment Directive 2014/68/EU FAS Manual Brass Shut-Off Valve DN10 through DN22 Please read these operating instructions carefully to ensure a safe operation
More informationEvacuation Raft. Product Manual
Evacuation Raft Product Manual MFC International 2017 1 Index Technical Data / Capacity Parts Parts List Materials List Operational Instructions Packing Storage Maintenance & Test Procedures Repairs 3
More informationSupratec. MEMBRANE-PLATE-DIFFUSER For fine bubble aeration of liquids BELÜFTUNGSTECHNIK UMWELT- & VERFAHRENSTECHNIK SERVICE & WARTUNG
BELÜFTUNGSTECHNIK UMWELT- & VERFAHRENSTECHNIK SERVICE & WARTUNG G E N E R A L I N F O R M A T I O N OXYFLEX - MF 1100 For fine bubble aeration of liquids Supratec GESELLSCHAFT FÜR U MWELT- U N D VERFAHRENSTECHNIK
More informationCR Series. Special doors for clean room application
CR Series Special doors for clean room application The CR Series: Special doors for clean rooms An increasing number of defined standards require reliable special doors for clean room application, for
More informationThe SAG type flat, rubber-steel, balance ropes
ROPES The SAG type flat, rubber-steel, balance ropes Application of the SAG ropes: The SAG type, flat, rubber-steel balance ropes, further on called the SAG ropes, are used for shaft transport at mines
More informationDR.ING. CARLO AVANZINI PROFESSIONAL ENGINEER GRIP TEST REPORT NOVA SIRIA, ROLETTO, Premise
GRIP TEST REPORT NOVA SIRIA, ROLETTO, 07.10.2013 1. Premise The present report covers the witnessing of the test conducted in the Nova Siria Factory in Roletto (Torino, Italy) to verify the behavior of
More informationMarking films application guide
Marking films application guide The application techniques that we will describe should help users by making their job easier, or by saving them time. However, we know that all the advice in the world
More informationPendant Drop Measurements
KRÜSS pplication Note TN316d Page 1 Pendant Drop Measurements pplication note: TN316d Industry section: all uthor: Dr. Tobias Winkler Date: December 2010 Method: Drop Shape nalysis System DS100 Drop Shape
More informationPRESSURE TANKS HANDLING & INSTALLATION INSTRUCTIONS INSTALLATION MANUAL CONTROL VALVES
PRESSURE TANKS HANDLING & INSTALLATION INSTRUCTIONS CONTROL VALVES INSTALLATION MANUAL TABLE OF CONTENTS Receiving & Handling 3 Basic Handling Continued 4 Approved Lifting Methods 5 Installing Pressure
More informationUnderstanding How the Appearance of Optical Fiber Splices Relates to Splice Quality
Understanding How the Appearance of Optical Fiber Splices Relates to Splice Quality Douglas Duke & David Mansperger Fusion Splicing Systems, AFL, Duncan, SC Doug.Duke@AFLglobal.com David.Mansperger@AFLglobal.com
More informationREGULATIONS FOR THE LICENSING OF MATS
REGULATIONS FOR THE LICENSING OF MATS (OLYMPIC GAMES WORLD AND CONTINENTAL CHAMPIONSHIPS WORLD AND CONTINENTAL CUPS TEAM WORLD AND CONTINENTAL CUPS GOLDEN GRAND PRIX FINALS CONTINENTAL AND REGIONAL GAMES)
More informationTechnical Data Sheet. R&M Closures
R&M Closures About this data sheet Edition 3.0 This document has been drafted with utmost care and reflects the products July, 2013 engineering level at the time of publication. Amendments or corrections
More informationMarking films - Application guide
Marking films - Application guide The application techniques that we will describe should help users by making their job easier, or by saving them time. However, we know that all the advice in the world
More informationPreparing and using manual gas welding equipment
Unit 030 Preparing and using manual gas welding Level: 2 Credit value: 14 NDAQ number: 500/9514/6 Unit aim This unit covers the skills and knowledge needed to prove the competences required to cover a
More informationOutline Physical Basis Aerosol Products Validation Algorithm Improvements. AEROCOM Meeting CNES, Paris, June 2-3, 2003
Aerosol Products from TOMS Omar Torres Joint Center for Earth Systems Technology University of Maryland Baltimore County NASA Goddard Space Flight Center Outline Physical Basis Aerosol Products Validation
More informationQuick reference. Quick reference
Quick reference Quick reference Measurement methodology for frequently occurring hose fittings Hose size ight series Heavy series Fine thread Banjo French (pipe in inches) French ( pipe light) French (
More informationOperating Instruction English. Revision A Date author NH This operating instruction is not subject to updating. Airgun
Revision A Date 23.11.2012 author NH This operating instruction is not subject to updating Airgun 95400 1 This airgun is a quality product with special focus on high functionality, easy handling, safety
More informationSterile Visual Flow Indicator
Sterile Visual Flow Indicator Sanitary Process Connection Installation / Operation / Maintenance Manual P.O. Box 1116 Twinsburg, OH 44087 Phone: 330/405-3040 Fax: 330/405-3070 E-mail: view@ljstar.com Web
More informationMSA Cairns FIRE HELMET PRODUCT SPECIFICATION
MSA Cairns FIRE HELMET PRODUCT SPECIFICATION PRODUCT TYPE: Structural Firefighting Helmet PRODUCT MODEL(S): PURPOSE: To supply a uniform, standard product specification for a thermoplastic structural fire
More informationEXPERIMENTAL RESULTS OF GUIDED WAVE TRAVEL TIME TOMOGRAPHY
18 th World Conference on Non destructive Testing, 16-20 April 2012, Durban, South Africa EXPERIMENTAL RESULTS OF GUIDED WAVE TRAVEL TIME TOMOGRAPHY Arno VOLKER 1 and Hendrik VOS 1 TNO, Stieltjesweg 1,
More information(Supplementary) Investigation Waves in a Ripple Tank
Purpose In this investigation you will study the behaviour of waves in two dimensions by observing water waves in a ripple tank. A ripple tank is a shallow, glass-bottomed tank. Light from a source above
More informationMagnetic Tape Installation Straight guide tape, embedded magnetic bar, curve segments HG A
Installation Instructions HG 19600-A Magnetic Tape Installation Straight guide tape, embedded magnetic bar, curve segments HG 19600-A English, Revision 01 Dev. by: TE Date: 25.06.2015 Author(s): RAD Götting
More informationUser Manual V14.1 IP68 LED FLEX NEON
User Manual V14.1 IP68 LED FLEX NEON PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLATION LEAVE A COPY FOR THE END USER/MAINTENANCE ENGINEER FOR FUTURE REFERENCE 1/11 PRODUCT SPECIFICATION 1. Operating
More informationB-05 SEAMLESS STEEL GAS CYLINDERS
Guideline No.: B-05(201705) B-05 SEAMLESS STEEL GAS CYLINDERS Issued date: May 9, 2017 China Classification Society Foreword: This Guide is a part of CCS Rules, which contains technical requirements, inspection
More informationUser Manual PTW-DensiX. D / Di/Zi
User Manual PTW-DensiX D148.131.0/3 2005-05 Di/Zi General Information General Information The product bears the CE-mark "CE-0124" in accordance with the Council Directive 93/42/EEC about Medical Devices
More informationSPECIFICATION FOR RAISED PAVEMENT MARKERS
SPECIFICATION FOR RAISED PAVEMENT MARKERS 1. SCOPE This specification covers performance requirements of retroreflective and nonretroreflective raised pavement markers which are bonded directly to the
More informationOperating Instructions
Operating Instructions Ex d Enclosures in Light Metal / Flameproof Encapsulation > 8265/0 Empty Enclosure > 8265/4 controller, installed in Ex e enclosure > 8265/5 controller Contents 1 Contents 1 Contents...2
More informationStatic dissipative Resin (Surface Resistivity : 10 4 ~10 7 Ω).
http://www.pisco.co.jp TUBE MAKE-TO-ORDER PRODUCTS for Anti-Static Environment Anti-Static 650 ESD Static dissipative Resin (Surface Resistivity : 10 4 ~10 7 Ω). Classification of conductivity region UE
More information1.0mm PITCH I/O CABLE IDT TOOL
INSTRUCTION MANUAL NO. IS-8023E ISSUED 1995-09-25 REVISED 2005-07-20 REV. G 1.0mm PITCH I/O CABLE IDT TOOL (Tool Number: 578xx-5000) OPERATING MANUAL Molex Japan Co., Ltd. Molex Japan Co., Ltd. Contents
More informationAnti-spatter Tube. Spatter-Proof Tube for Pneumatic Piping. Polyamide type Tube Coated with Flame-Retardant Resin(Equivalent to V-0 )
http://www.pisco.co.jp TUBE MAKE-TO-ORDER PRODUCTS Spatter-Proof for Pneumatic Piping Anti-spatter 646 Spark Resistance Polyamide type Coated with Flame-Retardant Resin(Equivalent to V-0 ) UL94 V-0 UL94
More informationMulti Core Tube for General Pneumatic Piping
http://www.pisco.co.jp TUBE MAKE-TO-ORDER PRODUCTS Multi Core for General Pneumatic Piping 616 Fine Flexibility. Simple Piping for Plural Actuators. Identification Line printed on Black Two-Core to Prevent
More information