ST70+ User Reference Manual. Document reference: Date: January 2009

ST70+ User Reference Manual Document reference: 85024-1 Date: January 2009

Autohelm, HSB, RayTech Navgator, Sal Plot, SeaTalk and Sportplot are UK regstered trademarks of Raymarne UK Lmted. Pathfnder and Raymarne are UK regstered trademarks of Raymarne Holdngs Lmted. 45STV, 60STV, AST, Autoadapt, Auto GST, AutoSeastate, AutoTrm, Bdata, G Seres, HDFI, LfeTag, Marne Intellgence, Maxvew, On Board,Raychart, Raynav, Rayplot, RayTalk, Raystar, ST40, ST60+, Seaclutter, Smart Route, Trdata, UnControl and Waypont Navgaton are trademarks of Raymarne UK Lmted. All other product names are trademarks or regstered trademarks of ther respectve owners. Copyrght 2008 Raymarne UK Ltd. All rghts reserved.

Contents Preface...v Safety notces... v EMC conformance... v Pressure washng... v Certfed nstallaton... v Product documents... v Techncal accuracy...v Product dsposal... v Chapter 1:General nformaton... 1 1.1 Introducton... 1 1.2 Product bascs... 1 Concept... 1 Keypad controls & control functons... 1 Sal boat Plot Controller keypad... 2 Power boat Plot Controller keypad... 2 Instrument keypad... 3 Keypad shortcuts... 3 Maxmum, mnmum & average ndcators... 4 Commonly used control functons... 4 Scrollng.... 4 OK functon... 4 1.3 Setup prncples... 5 Frst use after nstallaton... 5 Dsplay types & groupng... 6 1.4 Normal operaton... 7 Plot Controllers... 7 Sal boat functons... 7 Wnd Vane mode....7 AutoTack operaton... 7 Power boat functons... 9 Fshng patterns... 9 Instruments... 9 1.5 System nformaton...11 Power protocol...11 1.6 Commssonng requrement... 12 Autoplot calbraton... 12 Chapter 2:Commssonng Procedures... 13 2.1 Requrement... 13 Autoplot calbraton... 13 Control nformaton... 13 2.2 Intal setup... 13 Swtch on... 14 Selectng language... 14 Settng Vessel Type... 15 Select type... 15 Settng dsplay types and groups... 15

ST70+ User Reference Manual Date & Tme... 17 Settng date format... 17 Settng tme format... 18 Settng local tme... 18 Leavng date & tme setup... 18 Data unts... 19 Changng unts... 19 Leavng unts setup... 20 Intal setup end routne... 20 Next actons... 20 2.3 Docksde setup... 20 Autoplot system... 20 Docksde wzard... 21 Startng the wzard...21 Set drve type...21 Rudder and motor checks for systems wth a Rudder Reference transducer...22 Rudder and motor checks for systems wthout a Rudder Reference transducer...23 Hard over tme... 25 End of autoplot docksde setup... 25 Transducer setup... 25 Introducton to transducer setup... 25 Depth offsets...26 Accessng transducer setup... 26 Calbratng conventonal transducers... 28 Settng Depth offset...28 Settng water temperature...29 Calbratng smart transducers... 29 Calbratng trm tabs... 30 End of transducer setup... 30 Mscellaneous setup... 30 Settng ground wnd... 30 Settng magnetc varaton... 31 Changng dsplay response rate... 32 Rudder lmt... 33 Settng rudder offset... 33 Next actons... 33 2.4 Open water calbraton... 34 Autoplots... 34 Startng open water calbraton... 35 Compass calbraton... 35 Swngng the compass...35 Algnng the compass to GPS...36 Algnng the compass manually...36 AutoLearn... 37 Requrement for a clear area... 37 Procedure... 37 Next actons... 38 Instrument system calbraton... 38 Prelmnary procedure... 38 Wnd transducer setup... 39 Lnearzaton...39 Algnment...40 Calbrate wnd speed...40 Speed calbraton... 40

Speed calbraton for conventonal speed transducer... 41 Startng speed calbraton...41 Set to SOG...42 Manual speed calbraton...42 Speed calbraton for smart transducer... 43 Add pont...44 Delete pont...44 Return to normal operaton... 44 2.5 Checkng autoplot operaton... 44 General... 44 Checkng rudder gan... 45 Checkng counter rudder... 45 Rudder dampng... 46 Settng AutoTrm... 46 2.6 After commssonng... 46 EMC Conformance... 46 Chapter 3:Setup Informaton... 47 3.1 Introducton... 47 3.2 General setup... 47 Changng language... 47 Changng vessel type... 48 Change tme/date format... 48 Settng date format... 49 Settng tme format... 49 Leavng date & tme setup... 49 3.3 Autoplot setup... 50 Adjustng drve settngs... 50 Prelmnary procedure... 50 Settng response level... 50 Settng rudder gan... 51 Settng counter rudder... 51 Settng rudder dampng... 51 Settng AutoTrm... 51 Settng turn rate lmt... 52 Settng off course alarm... 52 Rudder lmt... 52 Settng rudder offset... 53 Power steer... 53 Settng lattude compass dampng... 53 AutoTurn... 54 Reverse rudder reference... 54 Checkng autoplot operaton... 54 Addtonal sal boat settngs... 55 Prelmnary procedure... 55 AutoTack angle... 55 AutoTack delay... 55 Gybe nhbt... 56 Wnd type... 56 WndTrm response... 56 Settng up fshng patterns... 56 3.4 System confguraton... 58 Changng system confguraton... 58

v ST70+ User Reference Manual Chapter 4:Mantenance & Troubleshootng... 59 4.1 Introducton... 59 Servcng & safety... 59 EMC... 59 4.2 Mantenance... 59 Cleanng... 60 Cablng... 60 4.3 Troubleshootng... 60 Frst consderatons... 60 Procedures... 60 Usng the dsplay self-montorng features... 65 About Dsplay... 65 About Plot... 66 Product support... 66 World wde web... 66 Telephone help lne... 66 Appendx 1:Specfcatons... 67 Dsplay...67 Keypads...67 All types... 67 Instrument keypad... 67 Plot Controller (power boat) keypad... 68 Plot Controller (sal boat) keypad... 68 Appendx 2:Glossary... 69 Index... 71

Preface v Contents Preface Safety notces WARNING: Product nstallaton & operaton Ths equpment must be nstalled, commssoned and operated n accordance wth the Raymarne nstructons provded. Falure to do so could result n personal njury, damage to your boat and/or poor product performance. WARNING: Swtch off power supply Ensure the boat s power supply s swtched OFF before startng to nstall ths product. Do NOT connect or dsconnect equpment wth the power swtched on, unless nstructed n ths document. WARNING: Ensure safe navgaton Ths product s ntended only as an ad to navgaton and must never be used n preference to sound navgatonal judgment. Only offcal government charts and notces to marners contan all the current nformaton needed for safe navgaton, and the captan s responsble for ther prudent use. It s the user s responsblty to use offcal government charts, notces to marners, cauton and proper navgatonal skll when operatng ths or any other Raymarne product. CAUTION: Replaceable parts Ths product does not contan any user servceable parts. Please refer all repar requrements to an authorzed Raymarne dealer. Unauthorzed repars may affect your warranty. EMC conformance All Raymarne equpment and accessores are desgned to the best ndustry standards for use n the recreatonal marne envronment. The desgn and manufacture of Raymarne equpment and accessores conform to the approprate Electromagnetc Compatblty (EMC) standards, but correct nstallaton s requred to ensure that performance s not compromsed. Pressure washng Do NOT pressure wash any Raymarne product. Subjectng any Raymarne product to hgh pressure washng may cause subsequent water ntruson and falure of the product. Raymarne wll not warranty product subjected to hgh pressure washng.

v ST70+ User Reference Manual Certfed nstallaton Raymarne recommends certfed nstallaton by a Raymarne approved nstaller. A certfed nstallaton qualfes for enhanced warranty benefts. Contact your Raymarne dealer for further detals and refer to the separate warranty document packed wth your product. Product documents The followng user documents are avalable for ST70+: ST70+ Operatng Gude. Ths comprses a seres of ndvdual operatng cards, whch provde day-to-day operatng and settng up procedures. Intended for all users. ST70+ User Reference Manual (ths document). Intended for users n general and commssonng personnel n partcular. It provdes: Commssonng procedures. These descrbe how to set up ST70+ dsplays when frst swtched on after nstallaton. Setup procedures not ncluded n the Operatng Gude Routne mantenance nstructons Troubleshootng nstructons ST70+ Installaton Gude. It provdes: Fttng procedures forst70+ dsplays and keypads. Connecton nstructons for ST70+ products Commssonng procedures. Addtonal nformaton on Raymarne SeaTalk ng systems s gven n the SeaTalk ng Reference Manual. Techncal accuracy To the best of our knowledge, the nformaton n ths document was correct at the tme t was produced. However, Raymarne cannot accept lablty for any naccuraces or omssons t may contan. In addton, our polcy of contnuous product mprovement may change specfcatons wthout notce. As a result, Raymarne cannot accept lablty for any dfferences between the product and ths document. Product dsposal Waste Electrcal and Electronc (WEEE) Drectve The WEEE Drectve requres the recyclng of waste electrcal and electronc equpment. Whlst the WEEE Drectve does not apply to some of Raymarne's products, we support ts polcy and ask you to be aware of how to dspose of ths product. The crossed out wheele bn symbol, llustrated above, and found on our products sgnfes that ths product should not be dsposed of n general waste or landfll. Please contact your local dealer, natonal dstrbutor or Raymarne Techncal Servces for nformaton on product dsposal.

1 Chapter 1: General nformaton 1.1 Introducton Ths manual provdes commssonng and other setup nformaton for ST70+ dsplays and assocated keypad controllers. It s also ntended for users who want to more fully understand the concepts of ST70+ and want to get the most out of ther product. For day-to-day use of ST70+, refer to the ST70+ Operatng Gude. 1.2 Product bascs An ST70+ system comprses one or more dsplays controlled by one or more keypads. Durng ntal setup, an ST70+ dsplay s set up to functon as ether an Instrument or a Plot Controller. The ntal setup s part of the commssonng procedure (see Chapter 2:, Commssonng Procedures). D11039-1 Dsplay nstrument keypad Plot Controller keypad (power boat) Plot Controller keypad (sal boat) Concept ST70+ dsplays are controlled by remote keypads, as follows: Instrument keypads control dsplays set up as Instruments. One type of Plot Controller keypad s used on sal boats to control dsplays set up as Plot Controllers. Another type of Plot Controller keypad s used on power boats to control dsplays set up as Plot Controllers. In any ST70+ system, dsplays and keypads can be confgured n convenent groups. For example, a system could comprse three Instrument groups (chart table, helm and mast), plus two Plot Controller groups (port helm and starboard helm). A dsplay or dsplay group can be controlled only by a keypad of the approprate type. Keypad controls & control functons All ST70+ setup and operatng functons are controlled by the keypad buttons. All keypads have: Power button. Swtches power on and off. Select Dsplay button. Used n systems wth more than one dsplay, to select the dsplay you want to control or set up. One press hghlghts the currently selected dsplay. If you press Select Dsplay agan whle the currently selected dsplay s hghlghted (.e. wthn 6 seconds), ths selects the next dsplay n the system or group. Repeatng ths acton enables you to select each dsplay n turn. CANCEL button. Used durng setup procedures to leave a setup functon wthout makng any changes.

2 ST70+ User Reference Manual Other buttons and ther functons depend on the keypad type. Sal boat Plot Controller keypad Sal boat Plot Controller keypad buttons and functons are: MENU button. Selects the Man Menu whch gves access to: Wnd Vane mode. AutoTack Port and Starboard - Sal boats only. Setup and reset functons. Self test routnes and dagnostc nformaton. The dsplayed Plot vew - plan, 2D or 3D (hold down). -1 and +1 buttons. Used to: Change course, when usng the autoplot to steer the boat. One degree to port or one degree to starboard, respectvely. Scroll to dfferent menu optons and change setup values, when settng up. -10 and +10 buttons. Used to change course, when usng the autoplot to steer the boat. Ten degrees to port or ten degrees to starboard, respectvely. OK button. used to confrm setup actons and values. AUTO button. Engages autoplot control. STANDBY button. Returns to manual control. TRACK button. Engages Track mode. DODGE button. Interrupts autoplot control to enable you to steer around obstacles on your plotted course. Power boat Plot Controller keypad Power boat Plot Controller keypad buttons and functons are: MENU button. Selects the Man Menu whch gves access to: Fshng pattern selecton. Power steerng. Setup and reset functons. Self test routnes and dagnostc nformaton. The dsplayed Plot vew - plan, 2D or 3D (hold down). Rotary Control: Rotate to change course, when usng the autoplot to steer the boat. Clockwse changes course to starboard, counter-clockwse, to port. Rotary Control. Press n to OK setup values & selectons One clck = one degree of course change, except when n Power Steer mode. Press n to perform an OK functon,.e. to confrm setup actons and values. Rotate to scroll to dfferent menu optons and change setup values. AUTO button. Engages autoplot control. STANDBY button. Returns to manual control. TRACK button. Engages Track mode. DODGE button. Interrupts autoplot control to enable you to steer around obstacles on your plotted course. D11402-1 D11403-1

Chapter 1: General nformaton 3 Instrument keypad Instrument keypad buttons and functons are: MENU button. Selects the Man Menu whch provdes access to: Setup and reset functons. Self test routnes and dagnostc nformaton. PAGE UP & PAGE DN buttons: Scroll to dfferent operatng pages. Select choces on setup screens. Rotary Control: Press n to perform an OK functon,.e. to confrm setup actons and values. Rotate to scroll to dfferent menu optons and change setup values. Keypad shortcuts Rotary Control. Press n to OK setup values & selectons Keypad shortcuts are avalable to access some functons. These are detaled n the followng table. D11404-1 Functon Condtons Smultaneously press Intate Power Steerng mode Intate Vane mode Intate tack to starboard Intate tack to port Access headng response page Access rudder response page Access rudder gan page Avalable from Plot Controller keypad on power boat, when autoplot s n Standby or Auto mode Avalable from Plot Controller keypad on sal boat, when autoplot s n Standby or Auto mode Avalable from sal boat Plot Controller keypad, when autoplot s n Auto mode Avalable from sal boat Plot Controller keypad, when autoplot s n Auto mode Avalable from any Plot Controller keypad Avalable from Plot Controller keypad on sal boat Avalable from Plot Controller keypad on sal boat AUTO and STANDBY (press and release) AUTO and STANDBY (press and release) +1 and +10 (press and release) -1 and -10 (press and release) MENU and CANCEL (press and release) +1 and -1 (press and release) +1 and -1 (hold down for 3 s) Start Setup wzard Avalable from any keypad Select Dsplay and MENU (hold down for 3 s)

4 ST70+ User Reference Manual Maxmum, mnmum & average ndcators Maxmum, mnmum & average value ndcators are dsplayed on speed, wnd speed and wnd angle screens, as n the followng llustraton: Mnmum value ndcator Average value ndcator Maxmum value ndcator Commonly used control functons Many ST70+ setup functons and values, plus many dsplay optons are selected by scrollng to the requred functon or value, then confrmng the value. The manner n whch you scroll to a functon or value you want and confrm your selecton, depends on keypad type. Scrollng. To scroll to an opton or set a value, ether: Press the < and > buttons on the sal boat Plot Controller keypad, or Turn the Rotary Control on the power boat Plot Controller keypad or the Instrument keypad OK functon The manner n whch you confrm, (.e. OK ) selectons and edted values depends on whch keypad type you are usng. On a salboat Plot Controller keypad, press and release the OK button. On a power boat Plot Controller keypad or an Instrument keypad, press and release the center of the Rotary Control. D11606-1 or Scrollng OK functons =

Chapter 1: General nformaton 5 1.3 Setup prncples A newly-nstalled ST70+ system must be commssoned as descrbed n Chapter 2:, Commssonng Procedures, before beng used for operatonal purposes. Frst use after nstallaton The frst part of the commssonng procedure s ntal setup (summarzed n Fgure 1-1). Ths starts automatcally on when a dsplay s frst swtched on after nstallaton. Frst swtch on Hold down POWER ON Intal setup Language Englsh (UK) Language select page Press OK to select OK Welcome page Setup wzard OK UNITS SUMMARY SELECT VESSEL TYPE OK OK UNITS SETUP Dsplay type & group setup See Fgure 1-2 MENU TIME & DATE SUMMARY OK OK Save and ext setup wzard If the dsplay functon has changed (.e. from Instrument to Plot Controller or vce versa), the dsplay reboots at ths pont. TIME & DATE SETUP OK Fgure 1-1: Intal swtch on and setup procedures If the dsplay s set up as an Instrument, an operatng page s dsplayed. If the dsplay s set up as a Plot Controller, and the autoplot has NOT been commssoned, the commssonng process starts automatcally. Refer to Chapter 2. D111134-1

6 ST70+ User Reference Manual The ntal setup procedure enables you to: Select system language. Select vessel type. Set up dsplay types & groups (see Fgure 1-2 ) Set tme and date formats. Set local tme value. Set unts. Dsplay types & groupng From Vessel type setup System confguraton OK Confgure ths dsplay Are all dsplays & groups set as requred? YES MENU NO Select dsplay to assgn functon and allocate to group To Tme & Date summary OK Dsplay type To be the same type for all dsplays n a Group OK Assgn group OK To be dfferent for each dsplay n a Group Assgn order n group OK Lnk keypad to group Lnk keypad to ths group? MENU NO On keypad you want to lnk, press YES OK Lnk keypad Keypad lnked to group Popup Fgure 1-2: Dsplay type & group setup summary Durng ntal setup, you allocate each ST70+ dsplay as ether an Instrument or a Plot Controller, then defne groups of Instruments and Plot Controllers (see Fgure 1-2:, Dsplay type & group setup summary). Each group s controlled by a common keypad or keypads. For example, you could group together all Instruments ftted at the helm and control them wth a sngle keypad. When groupng dsplays together, the followng rules apply: All dsplays n a group must be set to be the same type,.e. all Instruments or all Plot Controllers. A group can be just one dsplay, or a number of dsplays up to a maxmum of four. The keypad(s) allocated to a group must be approprate to the dsplay functon,.e. Instrument keypad for Instrument groups, Plot Controller keypad for Plot Controller groups. OK D11148-1

Chapter 1: General nformaton 7 1.4 Normal operaton ST70+ Plot Controllers and Instruments are controlled by dedcated Plot Controller keypads and Instrument keypads, respectvely. There two types of Plot Controller keypad, one for sal boat nstallatons, another for power boats. Plot Controllers ST70+ Plot Controllers are used to control Raymarne autoplots. A summary of generc ST70+ Plot Controller day-to-day functons s shown n Fgure 1-3. Sal boat functons In addton to the generc Plot Controller functons n Fgure 1-3, Plot Controllers on sal boats also have access to Wnd Vane and AutoTack modes of autoplot operaton. These are accessed va the Plot Controller Man menu. Wnd Vane mode. Wnd Vane mode automatcally mantans the boat s headng wth respect to the wnd angle. Thus f the wnd angle changes, the boat s headng changes accordngly to mantan the same relatve wnd angle (see ST70+ Operatng Gude). AutoTack operaton AutoTack enables you to select pre-defned tack operatons.tack port and Tack starboard optons are avalable. When usng AutoTack outsde of Wnd Vane mode (standard AutoTack), the AutoTack angle s the angle between a port tack and a starboard tack. The default angle s 100. Ths can be changed n User calbraton (see page 55). When usng AutoTack n Wnd Vane mode, the tack angle relatve to the wnd on one tack s mrrored on the other sde of the wnd on the next tack. Refer to the ST70+ Operatng Gude for detals of how to use AutoTack.

8 ST70+ User Reference Manual Hold down POWER ON The plot vew at swtch on, s same as when Plot Controller last swtched off Keypad functons Press & release STANDBY AUTO Normal Operaton Select next Plot Controller n group Select Standby mode (you have manual control) Select Auto mode (autoplot steers to locked headng) Hold down MENU Hold down to cycle to dfferent plot vew Press & release to select Man menu TRACK DODGE Select Track mode (autoplot tracks to preset course) Carry out Dodge manoever (manually steer round an obstacle) Profle dependent optons for: Fshng boat Power boat Sal boat Man menu RESPONSE LEVEL User setup DISPLAY SETTINGS Tme & Date setup* Brghtness setup Colors (day/nght optons) Unts setup* Response setup Data box setup PILOT VIEW Plan 2D 3D Count down to POWER OFF ADVANCED OPTIONS Setup Wzard Set Ground Wnd Transducer Setup Set Varaton Set Language* Select Boat Show Mode Set Vessel Type* Factory Reset DIAGNOSTICS About Dsplay Self Test * also part of ntal setup D11136-1 Fgure 1-3: Generc Plot Controller functons

Chapter 1: General nformaton 9 Power boat functons In addton to the generc Plot Controller functons (Fgure 1-3 ), Plot Controllers on power boats also have access to fshng patterns, va the Plot Controller Man menu. Fshng patterns Fshng patterns enable you to automatcally navgate over a preset course n Auto mode. The patterns avalable are: Crcle Zgzag Cloverleaf Spral Crcle aganst headng Fgure 8 Pattern search 180 turn Box search You can customze each pattern to gve exactly the coverage you want (see page 56). On fshng boats, PATTERN 1 and PATTERN 2 optons enable you to select ether of the two most frequently used patterns. Instruments A summary of the day-to-day functons for ST70+ Instruments s shown n Fgure 1-4, Normal operaton. Detaled operatng nstructons are gven n the ST70+ Operatng Gude.

10 ST70+ User Reference Manual Hold down POWER ON The operatng page at swtch on, s same as when ntrument last swtched off Instrument keypad PAGE UP PAGE DN Select prevous operatonal page Select next operatonal page Press & release Normal Operaton Select next Instrument n group Hold down MENU Press & release Hold down OK Count down to POWER OFF Fgure 1-4: Normal operaton Reset data pages Only resettable data types on the current operatonal page are avalable. ALARMS Edt alarm DISPLAY SETTINGS Tme & Date setup* Brghtness setup Colors (day/nght optons) Unts setup* Response setup Rollover setup Tmers setup PAGE LAYOUT Turn page on/off Rebuld page from new Change data ADVANCED OPTIONS Setup Wzard Transducer Setup Set Language* Set Vessel Type* Set Ground Wnd Set Varaton Select Boat Show Mode Factory Reset DIAGNOSTICS About Dsplay Self Test * also part of ntal setup User setup D11135-1

Chapter 1: General nformaton 11 1.5 System nformaton ST70+ dsplays and keypads connect to Raymarne SeaTalk ng systems. Further nformaton on SeaTalk ng s gven n the SeaTalk ng Reference Manual. When connected to a SeaTalk ng system, the ST70+ dsplays repeat the data on the bus. You can set the dsplay response as requred. You can set the system varaton only f t has not been set at another product. You can also calbrate the system transducers and set the data unts you want to apply to the system. Power protocol Power to ST70+ s swtched on and off usng the power button (as descrbed n the ST70+ Operatng Gude). However, where nstruments are part of a system, t may be more convenent to swtch power for the entre system from a central crcut breaker. In ths case, when system power s swtched ON agan: ST70+ nstruments that were swtched on when power was last swtched off wll return to the swtched ON state. ST70+ nstruments that were OFF when system power was last swtched OFF wll reman OFF and wll need to be swtched ON ndvdually usng ther power buttons.

12 ST70+ User Reference Manual 1.6 Commssonng requrement WARNING: Product nstallaton & operaton ST70+ products must be prepared for use n accordance wth the Commssonng Procedures, before they are used for operatonal purposes, unless they are part of a SeaTalk ng system n whch at least one other ST70+ dsplay s already set up and workng. Falure to comply wth ths could result n death, personal njury, damage to your boat and/or poor product performance. After nstallaton, each ST70+ dsplay that s NOT part of a SeaTalk ng system n whch at least one other ST70+ dsplay s already set up and workng must be commssoned n accordance wth Chapter 2: Commssonng Procedures, before t s used for operatonal purposes. Refer to the ST70+ Operatng Gude for nstructons on how to use the ST70+ products on a day-to-day bass. Autoplot calbraton The detaled requrement for autoplot calbraton depends on the autoplot type. The procedures gven n ths manual are those for a typcal Raymarne autoplot system. If necessary adapt the procedures n ths manual to sut your system. If you need assstance, contact your Raymarne dealer.

13 Chapter 2: Commssonng Procedures 2.1 Requrement WARNING: Product nstallaton & operaton ST70+ products connected to SeaTalk ng must be prepared for use n accordance wth the Commssonng Procedures, before beng used for operatonal purposes. Falure to comply wth ths could result n death, personal njury, damage to your boat and/or poor product performance. Note: Before an ST70+ system s used for the frst tme, t must be commssoned n accordance wth the nstructons n ths chapter. Commssonng comprses: 1. Intal setup. 2. Docksde setup. 3. Open water calbraton. 4. Checkng autoplot operaton. If your ST70+ product s connected to an exstng SeaTalk ng system that has already been successfully commssoned, you do not need to commsson the system agan. Autoplot calbraton The detaled requrement for autoplot calbraton s determned by the autoplot. The autoplot calbraton procedures n ths chapter are those for a typcal Raymarne autoplot system. If necessary adapt these procedures to sut your system. If you need assstance, please contact your Raymarne dealer. Control nformaton As the ST70+ dsplays do not have ftted controls, all control actons are made at the approprate ST70+ keypad. Wherever an nstructon calls for a button to be pressed or a control to be operated, ths refers to the approprate keypad. 2.2 Intal setup Carry out the ntal setup procedures n the followng sequence: Swtch on. Selectng language. Settng vessel type. Settng dsplay types and groups. Allocate keypad. Set date and tme format (only f GPS s ftted). Set correct local tme (only f GPS s ftted). Set requred data unts.

14 ST70+ User Reference Manual Swtch on. At an ST70+ keypad, press the power button to swtch on the dsplays. When an ST70+ system s frst swtched on after nstallaton, one dsplay shows a select Language menu. Ths s the actve dsplay Language Englsh (UK) Other dsplays show a Select Dsplay con. Press OK to select If necessary use the Select Dsplay button on any ST70+ keypad to select another dsplay as the actve dsplay,.e. so t shows the select Language menu. D11140-1 Selected dsplay Language Englsh (UK) Press OK to select Selectng language Scroll to select the requred language. D11407-1 CAUTION: Be sure to select the correct Language. If you select the wrong language, the ST70+ system wll be dffcult to use. If you are sure you have selected the language you want, press OK to confrm the selecton, to dsplay the Welcome screen. When you are ready to proceed, press OK to dsplay the Vessel Type menu.

Chapter 2: Commssonng Procedures 15 Settng Vessel Type The Vessel Type menu enables you to automatcally apply the optmum system settngs for your vessel type. The optons are: Race Sal Inboard Speed Boat Sal Cruser Power Cruser 1* Catamaran Power Cruser 2* Workboat Power Cruser 3* RIB Sport Fshng Outboard Speed Boat Pro Fshng *Power Cruser settngs. Note that the Power Cruser settngs apply as follows: Power Cruser 1 - vessels capable of speeds up to 12 knots. Power Cruser 2 - vessels capable of speeds up to 30 knots. Power Cruser 3 - vessels capable of speeds greater than 30 knots. Select type Scroll to select the vessel type that most closely corresponds to your vessel. When you have chosen the vessel type, press OK to confrm the choce. The Tme and Date values and the data Unts consdered most approprate for the Language and Vessel Type you chose, are then automatcally appled to your ST70+ system and an automatc check of system parameters s carred out. On completon, a System confguraton page s present all dsplays n the system. Settng dsplay types and groups You must now: Select the dsplay you want to set up. Set the dsplay type for each dsplay (Instrument or Plot Controller). Allocate each dsplay to a group. Set the sequence number of each dsplay wthn the group. Lnk at least one keypad to each group. To do ths: 1. Wth the System confguraton page dsplayed, press OK to dsplay the Confgure ths dsplay page. For unassgned dsplays (e.g. at frst swtch on), the legends Group and Number are dsplayed. If the selected dsplay has already been set up, ths shows the current group and number n the group for the selected dsplay. Vessel Type Press OK to confgure ths dsplay 2. Use the Select Dsplay button as necessary, to move the screen hghlght to the dsplay you want to set up,. e. so t s the selected dsplay. Inboard Speedboat Selectng vessel type helps us to confgure your system. Press OK to select Confgure ths dsplay Group Number Select each dsplay n turn. Press OK to confgure. When all done, press MENU. D11143-1 D11141-1

16 ST70+ User Reference Manual Note: Note: 3. Press OK to dsplay the Dsplay type setup page. 4. Scroll to select ether Instrument or Autoplot, as requred. From ths pont, you must use a keypad type approprate to the dsplay type you have selected. 5. Press OK to confrm the dsplay type and dsplay the Assgn group page. 6. Scroll to the name of the group to whch you want to assgn the dsplay. Plot Controller group name optons are: Plot-1, Plot-2, Plot-3, Plot-4 and Plot-5 Instrument group name optons are: Inst-Helm1, Inst-Helm2, Inst-Cockpt, Inst-Flyb., Inst-Mast, Inst-1, Inst-2, Inst-3, Inst-4, Inst-5, Inst-6, Inst-7, Inst-8, Inst-9, Inst-10, Inst-11, Inst-12, Inst-13, Inst- 14 and Inst-15. 7. Press OK to save the group assgnment and dsplay the Assgn order n group page. Each dsplay n a group has a dscrete number, and these numbers determne the order n whch dsplays are selected wthn the group durng normal operaton, when the Select Dsplay button s used. 8. Scroll to the requred number. 9. Press OK to save the group settngs and dsplay the Lnk keypad to group page. 10. If you have not allocated keypads to the group contanng the dsplay you are settng up:. Press OK at a keypad you want to lnk to ths group.. Wat untl the confrmng popup dsappears.. Repeat and for each keypad you want to lnk to ths group. Remember you can only lnk Instrument keypads to Instrument groups, and Plot Controller keypads to Plot Controller groups. 11. When you have allocated all the requred keypads to ths group, press MENU to save the group settngs and dsplay the Confgure ths dsplay page. 12. Repeat steps 3 to 11 for each dsplay. Dsplay type Autoplot Confgure ths dsplay as an nstrument or autoplot controller Assgn group Plot-2 Assgn nto a group of one or more dsplays. All dsplays must be the same type. Assgn order n group 2 Assgn the order of ths dsplay wthn the group. Lnk keypad to group Press OK on each keypad that you want to lnk to ths dsplay group Press MENU to fnsh D11144-1 D11145-1 D11146-1 D11147-1

Chapter 2: Commssonng Procedures 17 13. When all dsplays are set as you want, and wth the Confgure ths dsplay page dsplayed, press MENU, to leave the Settng dsplay types and groups procedure, and dsplay ether: A Tme & date summary page, f your system provdes GPS nformaton, or A Unts Summary page f GPS nformaton s not avalable. Note: Date & Tme The Tme & Date summary page shows the current values appled to your ST70+ system. Date 14/06/07 If your dsplay s not recevng GPS nformaton, the Tme Tme Offset -1 Hrs & Date page s not dsplayed. In ths case, proceed wth Tme Format 24-hour the Data unts setup procedure below. Date Format dd/mm/yy Check the nformaton, on the Tme & Date summary page, then press OK to dsplay the Tme & Date setup menu. Press OK to contnue You can change certan date and tme parameters. You can: Select ether dd/mm/yy or mm/dd/yy as the date format Select ether 12-hour (am/pm) or 24-hour as the tme format. Set the value of the tme offset to gve the requred local tme. If you want to change any Tme & Date values, carry out the Settng date format, Settng tme format and/or Settng local tme procedure below, as approprate. If you do not want to change any Tme & Date values, proceed from Leavng date & tme setup below. Settng date format To set the requred date format: 1. At the Tme & Date setup menu, scroll to the Set date format opton, then press OK to dsplay the Set date format page. Tme & Date Tme 11:01:03 10 These are your current settngs. Tme & Date 10 Set date format D11149-1 Press OK to select D11153-1 2. Scroll to select the requred Date Format, then press OK to save the format and return to the Tme & Date summary page. 3. Press OK to select the Tme & Date setup menu. Set date format 10 dd/mm/yy Use < & > to adjust. CANCEL exts wthout savng. D11154-1

18 ST70+ User Reference Manual Settng tme format To set the requred tme format: 1. Wth the Tme & Date setup menu dsplayed, scroll to select the Tme Format opton, then press OK to dsplay the Set tme format page. Tme & Date 10 Set tme format Press OK to select D11155-1 2. Scroll to the requred Tme Format, then press OK to save the format and return to the Tme & Date summary page. 3. Press OK to select the Tme & Date setup menu. Set tme format 12-hour Settng local tme Note: If your ST70+ dsplay s connected to a Raymarne multfuncton dsplay, then the tme offset s controlled by the multfuncton dsplay and you cannot use ths procedure to change t. To set the dsplay tme to your local tme. 1. At the Tme & Date setup menu, use < and > to select the Set tme offset opton, then press OK, to dsplay the Set tme offset page. Use < & > to adjust. CANCEL exts wthout savng. Tme & Date D11156-1 Set tme offset Press OK to select D11157-1 2. Scroll to set the correct local tme. For example, f your local tme s 1 hour after GMT, set -1. 3. Press OK, to save the settng and return to the Tme & Date setup menu. Set tme offset -1 hour Leavng date & tme setup When your date and tme formats and values are set as requred: 1. At the Tme & Date setup menu, scroll to the Contnue opton. 2. Press OK to proceed to the Unts summary page. 3. Proceed from Data unts (below). Use < & > to adjust. CANCEL exts wthout savng. Tme & Date Contnue Press OK to select 10 D11158-1 D11150-1

Chapter 2: Commssonng Procedures 19 Data unts The Unts summary comprses two pages and shows unts currently n use. You can accept all or change any of the data unt settngs. You can set:. Speed to ether mles per hour, klometers per hour or knots. Dstance to ether mles, nautcal mles or klometers Depth to ether feet, fathoms or meters. Wnd speed to ether knots or meters per second. Headng to ether magnetc or true. Flow rate to ether US gallons per hour, UK gallons per hour or lters per hour Temperature to degrees Celsus or degrees Fahrenhet. Pressure to pound per square nch or klo Pascals. Volume to ether US gallons, UK gallons or lters Number of engnes to ether 1, 2, 3, 4 or 5. Number of batteres to ether 1, 2, 3, 4 or 5. Number of fuel tanks to ether 1, 2, 3, 4 or 5. Press OK to see the second Unts summary page, and f you want to return to the frst page from the second, press CANCEL. Check the nformaton on the Unts summary Select unts pages, then wth the second Unts summary page dsplayed, press OK to dsplay the Select unts menu. If you want to change any data unts, carry out the Changng unts procedure below. If you do not want to change any data unts, proceed from Leavng unts setup below. Changng unts To change any data unts: 1. Wth the Select unts menu dsplayed, scroll to select the type of data you want to change,.e. Speed, Depth, Dstance, Wnd Speed etc. 2. Press OK to dsplay the setup page for the unts you have selected. 3. Scroll to select the requred unts. 4. Press OK to save the unts settng and return to the frst Unts summary page. 5. Press OK twce, to dsplay the Select unts menu. 6. If you want to change any other unts, repeat steps 1 to 5 of ths procedure. Unts summary 6 Speed pt Dstance Depth Wnd Speed Headng Flow Rate Temperature These are your current settngs. Press OK to contnue Wnd Speed Unts Select unts to change, usng < or >. Press OK to select Wnd Speed Unts KTS KTS NM FT KTS Mag G/H oc Select requred unts, usng < or >. CANCEL exts wthout savng. D11159-1 D11161-1 D11106-1

20 ST70+ User Reference Manual Leavng unts setup When your data unts are set as requred: 1. Wth the Select unts menu dsplayed, scroll to the Contnue opton. 2. Press OK. Intal setup now ends. Intal setup end routne If the functon of any dsplay has changed snce swtch on (.e. Instrument to Plot Controller or vce versa), the relevant dsplays reboot when you press OK at the Select unts menu. When any necessary reboot has taken place, an operatonal page for ether an Instrument or a Plot Controller s dsplayed, dependng on whch dsplay functon you set prevously. The dsplay s now n operatng mode. Next actons Now carry out the remanng docksde setup procedures. Select unts 2.3 Docksde setup Carry out the docksde setup procedures n the followng sequence: Autoplot system. Transducer setup. Mscellaneous setup. Autoplot system CAUTION: Before startng any docksde setup procedure, ensure the boat s securely moored alongsde. The autoplot docksde setup procedures comprse: Usng the Docksde wzard to: Set drve type. Perform motor phasng check. Perform rudder check. Settng rudder hard over tme. The exact procedures are dependent on the type of autoplot. Typcal procedures are gven here, but you may need to adapt these procedures to sut your nstallaton. If you requre advce or assstance, please contact your local Raymarne dealer. Contnue Select unts to change, usng < or >. Press OK to select D11160-1

Chapter 2: Commssonng Procedures 21 Docksde wzard Startng the wzard At a convenent Plot Controller: 1. Press MENU to dsplay the Man Menu. 2. Scroll to Autoplot calbraton then press OK to dsplay the Autoplot Autocalbraton menu. 3. Scroll to select Commssonng then press OK to dsplay the Commssonng menu. 4. Scroll to Docksde wzard then press OK to start the wzard. The Docksde Calbraton page s dsplayed. Docksde Calbraton Before you can use your autoplot you need to do some docksde checks. Press CANCEL to ext wthout savng. Note: Set drve type Wth the Docksde calbraton page dsplayed at the Press OK to contnue Drve Type selected Plot Controller, press OK on the assocated keypad to dsplay the Drve type page then:. 1. Scroll to select the autoplot drve type approprate to your boat.the optons avalable depend on the type of autoplot, but optons supported are: Type 1 Lnear CANCEL returns to the prevous page. Press OK to select Type 1 Lnear Jet Drve (fly-by-wre) Type 2 Lnear Wheel Drve Type 2 Hydraulc Lnear Tller Hydraulc Pump Type 1 Type 3 Hydraulc Lnear CR Solenod Hydraulc Pump Type 2 I/O Stern Sport Drve Hydraulc Pump Type 3 IPS Rotary Drve Type1 Constant Runnng Pump Jet Drve (pump) Rotary Drve Type 2 Verado If your drve type s not ncluded, seek advce from your Raymarne dealer. 2. Press OK to save your settng and dsplay the next setup page. Ths s ether: The Rudder check (center) page, f the boat has a rudder reference transducer, or The Motor phasng non-referenced page, f a rudder reference transducer s not ftted. 3. Press OK to proceed wth the Rudder and motor checks. Use the procedure for ether Systems wth a Rudder Reference transducer or Systems wthout a Rudder Reference transducer, as approprate. D11164-1 D11165-1

22 ST70+ User Reference Manual Rudder and motor checks for systems wth a Rudder Reference transducer After settng the drve type, the Rudder check page Rudder Check (center) s dsplayed, f your system has a Rudder Reference transducer. If ths s the case, carry out the rudder and motor checks as follows: 1. Manually center the rudder. 2. Press OK to dsplay the Rudder Check (port) page. 3. Turn the wheel fully to port. Center the rudder and press OK. Press CANCEL to ext. Rudder Check D11170-1 4. Press OK to dsplay the Rudder Check (starboard) page. 5. Turn the wheel fully to starboard. Turn the wheel hard to PORT and press OK. Press CANCEL to ext. Rudder Check D11168-1 6. Press OK, to dsplay the Rudder Check page (center) agan. Turn the wheel hard to STARBOARD and press OK. Press CANCEL to ext Rudder Check D11169-1 7. Press OK to dsplay the Rudder Check Task Complete page. Center the rudder and press OK. Press CANCEL to ext. Rudder Check D11170-1 Task Complete - success. Press CANCEL to ext. Press OK to contnue D11171-1

Chapter 2: Commssonng Procedures 23 8. Press OK, to dsplay the Motor Check entry page. Motor Check 9. Press OK, to dsplay a Motor Check cauton page. IS IT SAFE TO TAKE THE HELM! Press CANCEL to ext Press OK to contnue Motor Phasng Non-referenced Please center and let go of rudder and release any rudder drve clutch. Press OK f t s safe for Autoplot to engage the rudder drve. D11610-1 10. Manually center the rudder, then f t s safe to proceed, press OK. The autoplot automatcally drves the rudder n one drecton. When ths s complete a result page s dsplayed. Press CANCEL to stop Motor Check Rudder drve has been detected. Please press OK f t s safe to engage the rudder drve n the opposte drecton. D11611-1 Press CANCEL to stop D11612-1 11. If t s safe to proceed, press OK. The autoplot then drves the rudder n the opposte drecton. When ths check s complete, a Motor Check Task Complete page s dsplayed. 12. Press OK to end the autoplot docksde wzard. Motor Check Task Complete - success Press CANCEL to stop Rudder and motor checks for systems wthout a Rudder Reference transducer After settng the drve type, the Motor Phasng Nonreferenced entry page s dsplayed, f your system Motor Phasng Non-referenced does not have a Rudder Reference transducer. D11613-1 IS IT SAFE TO TAKE THE HELM! Press CANCEL to ext Press OK to contnue D11614-1

24 ST70+ User Reference Manual Carry out the rudder and motor checks as follows: 1. Press OK to dsplay a Motor Check cauton page. 2. If t s safe to proceed. press OK, then check whch way the autoplot drves the rudder.drecton. Motor Phasng Non-referenced Please center and let go of rudder and release any rudder drve clutch. Press OK f t s safe for Autoplot to engage the rudder drve. Press CANCEL to stop D11615-1 3. When the PORT result page s dsplayed, press ether: OK f the rudder moved to port, or CANCEL f the rudder dd not move to port. Motor Phasng Non-referenced 4. If you press OK a second Motor Check cauton page s dsplayed. 5. If t s safe to proceed. press OK, then check whch way the autoplot drves the rudder.drecton. 6. If you press OK a second Motor Check cauton page s dsplayed. 7. When the STBD result page s dsplayed, press ether: OK f the rudder moved to starboard, or CANCEL f the rudder dd not move to starboard. Dd the rudder move to PORT? Press CANCEL for NO. Press OK for YES Motor Check Please press OK f t s safe to engage the rudder drve n the opposte drecton. Press CANCEL to stop Motor Phasng Non-referenced D11613-1 D11617-1 8. If you press OK a task complete page s dsplayed. 9. Press OK to end the autoplot docksde wzard. Dd the rudder move to STBD? Press CANCEL for NO. Motor Check Press OK for YES D11618-1 Task Complete - success Press CANCEL to stop D11613-1

Chapter 2: Commssonng Procedures 25 Note: Hard over tme Not applcable to boats wth a rudder reference transducer. On boats wthout a rudder reference transducer, t s of crtcal mportance to set the hard over tme, to ensure accurate autoplot operaton. To do ths: At a convenent Plot Controller: 1. Press MENU to dsplay the Man Menu. 2. Scroll to Autoplot calbraton then press OK to dsplay the Autoplot Autocalbraton menu. 3. Scroll to select the Drve settngs opton then press OK to dsplay the Drve settngs menu. 4. Scroll to select the Hard Over tme opton then Hard Over Tme press OK to dsplay the Hard Over tme page. 5. Measure the tme t takes for the autoplot to drve the rudder from hard over port, to hard 12 over starboard. 6. On the Hard over tme page, scroll to set the approprate tme n the edt box. The tme to drve between lmts. 7. Press OK to save the settng and return to the Drve settngs menu. End of autoplot docksde setup At the end of the autoplot docksde setup, use the CANCEL button to return to a Plot Controller operatonal page. Before startng any sea tral or other open water calbraton, carry out the Transducer setup and Mscellaneous setup procedures (below). Transducer setup CAUTION: Before startng any docksde setup procedure, ensure the boat s securely moored alongsde. Use these docksde setup procedures to set: Correct depth offset and sea temperature. Requred method for calculatng ground wnd. Correct magnetc varaton. Requred nstrument response. Trm tab calbraton. Introducton to transducer setup Depth, speed and temperature data are derved from transducers n the boat s hull. Ether of the followng transducer confguratons may be ftted to provde ths data: Conventonal transducers,.e. separate Depth and Speed, wth the water temperature sensor bult nto the Speed transducer. Smart transducers (ether combned Depth/Speed/Temperature (DST) or combned Depth/Temperature (DT) transducers). D11332-1

26 ST70+ User Reference Manual A Wnd transducer may also be ftted, to provde wnd speed and drecton nformaton. Depth offset and sea temperature must be calbrated as part of the Docksde setup, but the exact method for calbratng these parameters depends on whch transducers are ftted: Wth conventonal transducers, the Depth offset and water temperature are calbrated separately. Wth a smart transducer, the depth offset and water temperature setup are part of one contnuous procedure. The speed and wnd functons are calbrated later as part of the Open water calbraton. Depth offsets Depths are measured from the Depth transducer to the sea bed, but you can apply an offset value to the depth data, so that the dsplayed depth readng represents the depth to the sea bed from ether the keel or the water lne. If an offset s not appled, the dsplayed depth readngs are from the transducer to the sea bed. Before attemptng to set a waterlne or keel offset, fnd out the vertcal separaton between the transducer and ether the waterlne or the bottom of the keel on your vessel, as approprate. See Fgure 2-1. Waterlne offset Offset value of 0.0 Keel offset D9343-1 Fgure 2-1 Depth offsets Accessng transducer setup Use the Select Dsplay button on a sutable Instrument keypad, to select a convenent Instrument to carry out the Instrument system docksde setup procedures.

Chapter 2: Commssonng Procedures 27 To access the requred transducer: 1. Wth any operatonal Instrument page dsplayed, press MENU to dsplay the Man Menu. 2. Scroll to Advanced Optons, then press OK 3. At the Advanced Optons menu, scroll to Transducer Setup. Advanced Optons Transducer Setup Press OK to select D11172-1 4. Press OK to dsplay the Transducer setup start search page. Transducer Setup ST70+ wll now search the network for transducers. Press CANCEL to abort. Press OK to contnue D11173-1 5. Press OK agan to ntate a system search for transducers. At the end of the search, a Search results page s dsplayed. Search Results Found: 1 Depth 1 Speed 1 Wnd 0 DST800 0 DT800 1 Trmtabs 6. Wth the search results page dsplayed, press OK to access the Transducers found menu. 7. Set up the followng: The correct Depth Offset, usng the procedure descrbed under ether Calbratng conventonal transducers or Calbratng smart transducers as approprate The correct Water Temperature usng the procedure descrbed under ether Calbratng conventonal transducers or Calbratng smart transducers as approprate. The Trm tabs (f applcable). If not correct, press CANCEL and check connectons. Press OK to contnue Transducers Found Depth Raymarne Seral no.135260 Press OK to select D11208-1 D11174-1

28 ST70+ User Reference Manual Calbratng conventonal transducers Use these procedures to calbrate Depth & Temperature values for conventonal transducers. Settng Depth offset If you want to apply an offset to your depth readngs, you MUST ensure the offset value s correct, before relyng on subsequent Depth data. WARNING: Ensure you use the correct depth offset The use of the correct depth offset s crtcal to the safety of the vessel. If an ncorrect offset value s appled, ths could result n msleadng depth nformaton beng dsplayed wth a consequent rsk of runnng aground. Take great care to ensure you set the correct value. Set the correct depth offset as follows: 1. Wth the Transducers found menu dsplayed, select Depth. to dsplay the Depth transducer menu. 2. Wth the Depth transducer menu dsplayed, scroll to the Depth Offset opton, then press OK, to dsplay the Depth Offset setup page. Check the type and value of the offset currently appled: If the offset type s what you requre and the value s correct for your boat, press CANCEL to return to the Depth transducer menu, then proceed from step 6. Otherwse proceed from step 3. 3. If necessary, press PAGE UP to select the upper (offset type) adjust box. 4. Scroll to ether Water lne, Keel or Transducer, as requred. If you select Transducer, an offset value of zero s automatcally appled. 5. If you have selected: Ether Water lne or Keel, press PAGE DN to select the lower (offset value) adjust box then scroll to set the correct value. Transducer, ensure the offset value s zero. Depth 6. Press OK to save the offset value and dsplay the Depth transducer menu. 7. Press CANCEL to return to the Transducers found menu. Depth Offset Raymarne Seral no. 211342 Press OK to select Depth Offset Keel 2.5 FT Warnng! Incorrect depth offset may lead to vessel runnng aground. D11175-1 D11176-1

Chapter 2: Commssonng Procedures 29 Settng water temperature Set the correct water temperature as follows: 1. Wth the Transducers Found menu dsplayed, scroll to the Speed opton. 2. Press OK to dsplay the Speed transducer setup menu. 3. Scroll to the Temperature Offset opton. 4. Press OK to dsplay the Temperature Offset setup page. Transducers found Speed Raymarne Seral no.165321 Press OK to select D11177-1 5. Usng a sutable thermometer, measure the water temperature, then scroll to set the correct system temperature value. 6. the value and return to the Speed transducer menu. 7. Press CANCEL to return to the Transducers found menu. 8. Press CANCEL to return to the Search Results summary. 9. Press CANCEL to return to the Transducer Setup start page. 10. Press CANCEL to return to the Advanced Optons menu. Calbratng smart transducers WARNING: Ensure you use the correct depth offset The use of the correct depth offset s crtcal to the safety of the vessel. If an ncorrect offset value s appled, ths could result n msleadng depth nformaton beng dsplayed wth a consequent rsk of runnng aground. Take great care to ensure you set the correct value. Use ths procedure to calbrate Depth & Temperature values for a smart transducer: 1. Wth the Transducers found menu dsplayed, select DST or DT to dsplay the Detals page. 2. Press OK, to dsplay the Depth Offset setup page. 3. Check the type and value of the offset currently appled: If the offset type s what you requre and the value s correct for your boat, proceed from step 7. Otherwse proceed from step 4. Temperature Offset 7 C Adjust temperature untl t reads actual sea temperaure Detals Manufacturer Transducer Model No. Seral No. Software Hardware Voltage Press OK to select Armar DST DST800 11.8 V D11179-1 D11335-1