Mower - Roller Br Instlltion nd Leveling Instructions 4 Model: 9555, 9594 Attention Setup Personnel: 5 4 5 Model: 958, 9595 Model: 9559 Model: 959 The sfety wrnings provided in this guide nd in the trctor's opertor mnul included with the unit contin importnt informtion tht must be followed when ssembling, setting-up, operting, servicing, trnsporting, or storing the unit. These wrnings re highlighted by the sfety lert tringle symbol shown bove, which signifi es tht n importnt sfety messge is being provided. You must red, understnd, nd follow these wrnings nd instructions, nd use sfe shop nd work prctices t ll times while working on or round this unit nd ll other outdoor power equipment. WARNING AVOID SERIOUS INJURY OR DEATH: Red nd follow the trctor opertor mnul before running engine. Gsoline is flmmble. Allow engine to cool t lest minutes before refueling. Engines emit crbon monoxide. DO NOT run in enclosed re. Muffler re temperture my exceed 50 F. DO NOT touch hot prts. Form No.: 9498 Revision: D
Tools Preprtion EYE PROTECTION WORK GLOVES WARNING WRENCHES / / 9/ /4 5/ SCREW DRIVER TORQUE WRENCH TIRE PRESSURE GAUGE MEASURING TOOL (4 inch stiff crdbord) For your personl sfety, do not hndle the shrp mower bldes with bre hnds. Creless or improper hndling of bldes my result in serious injury. Plce trctor on hrd level surfce nd turn wheels to the left. -4 psi (0,8-0,9 br) Check tires for the correct pressures. 0 psi (0,8 br) Fully rise ttchment lift. 4 Disengge mower bldes. 5 Engge prking brke. Turn ignition OFF nd remove key. Disconnect sprk plug wires nd plce wy from plugs.
Mower Assembly Mower Instlltion Models 9555, 9594,958, 9595 INSTALL DEFLECTOR Note: Use screw driver () to line up brcket holes. ATTACH FRONT HITCH TO TRACTOR Note: Remove fsteners, rotte hitch, nd fsten djusting rod (). lb-ft (5 Nm) 4 5 0 lb-ft (. Nm) 8
Mower Instlltion Mower Instlltion Models 9559, 959 All models ATTACH FRONT HITCH TO TRACTOR Note: Remove fsteners, rotte hitch, nd fsten djusting rod (). ATTACH REAR MOWER CHAINS Note: Lift rer of mower using two bords. 0 lb-ft (. Nm) 4 5 4 Fully lower ttchment lift. Plce mower deck in the lowest height of cut position. 5 (X) 4
ATTACH BELT ON ENGINE DRIVE PULLY CONNECT TRACTOR HARNESS TO DECK ACTUATOR MOTOR 4 A 5 5
Mower Deck Leveling SIDE-to-SIDE LEVELING FRONT-to-BACK LEVELING Importnt: The eccentric nut (c) nd locknut (d) come from from the fctory loose, proceed with the directions below.. Plce the mower deck pproximtely in the middle height of cut position.. Arrnge the two rer bldes so they re pointing from side-to-side. Using mesuring tool, mesure the distnce between the outside tips (, b) of ech blde nd the ground. The difference should be: less thn /8 (mm).. If the mower is level, hold the eccentric nut (c) while tightening the locknut (d). If the mower is NOT level, turn the eccentric nut (d) to rise or lower left hnd side of mower. When mower is level, hold the eccentric nut while tightening the locknut (d). lb-ft (5 Nm) d b c Importnt: The eccentric nut (d) nd locknut (e) come from from the fctory loose, proceed with the directions below.. Arrnge the bldes so they fce front to bck. Using mesuring tool, mesure the distnce between: lb-ft (5 Nm) () - the distnce between the rer tip of one of the bck bldes nd the ground. (b) - the distnce between the front tip of the center blde nd the ground. This should be /4 ( mm) higher thn mesurement (). e If the mower is level ccording to Step b, hold the eccentric nut (d) while tightening the locknut (e) d b
. If more thn /8 (0 mm) of djustment is needed: Support the deck in front using two bords Loosen bolts (c) on the djusting rod, then djust the bords until deck is level ccording to Step b. Tighten bolts nd torque s shown. If less thn /8 (0 mm) of djustment is needed: Turn the eccentric nut (d) to rise or lower front side of mower. When mower is level ccording to Step b, hold the eccentric nut while tightening the locknut (e). lb-ft (5 Nm) c lb-ft (5 Nm) e d