Evidence of Performance Test Report No 16-002359-PR01 (PB-A01-02-en-01) Client Product Designation Performance-relevant product details Overall dimensions (W x H) Special features - / - SUNCE Marinkovic d.o.o. Lepenicki bulevar br.39 34 000 Kragujevac Serbia Tilt and turn window System designation: REHAU Synego MD Material: PVC/U-white 1,230 mm x 1,480 mm Basis EN 14351-1:2006+A1:2010 Test standard/s: EN 1026:2000-06 EN 1027:2000-06 EN 12211:2000-06 Correspond/s to the national standard/s (e.g. DIN EN) Representation Results Air permeability according to EN 12207:1999-11 ift Rosenheim 14.02.2017 Class 4 Watertightness according to EN 12208:1999-11 Class 5A Resistance to wind load according to EN 12210:1999-11/AC:2002-08 Class C5 / B5 Michael Breckl-Stock, M.Eng., Dipl.-Ing. (FH) Deputy Head of Testing Department Construction Product Testing Robert Kolacny, Dipl.-Ing. (FH) Operating Product Officer Building Components Instructions for use The manufacturer is allowed to use the results obtained for preparing a Declaration of Performance in accordance with the Construction Products Regulation 305/2011/EC. Observe the specifications set out by the applicable product standard. Validity The data and results refer solely to the tested and described specimen. Classification remains valid as long as the product and the above basis remain unchanged. The results can be extrapolated under the manufacturer's own liability subject to observance of the relevant specifications set out by the applicable product standard. This test/evaluation does not allow any statement to be made on any further characteristics regarding performance and quality of the construction presented; in particular the effects of weathering and ageing were not taken into account. Notes on publication The ift-guidance Sheet "Advertising with ift test documents" applies. The cover sheet can be used as an abstract. The report contains a total of 24 pages. Ve-Prü-2087-en 01.06.2016
Evidence of Performance Page 2 of 14 1 Object 1.1 Description of test specimen Product Manufacturer, manufacturing plant Tilt and turn window Date of manufacture 30.11.2016 Profile system SUNCE Marinkovic d.o.o. REHAU Synego MD Type of opening / opening direction tilt and turn, DIN right inward opening Frame material PVC/U white Overall frame dimensions (W x H) 1,230 x 1,480 Overall sash dimensions (W x H) Right sash weight Frame member Designation / Type / Item No. Frame joint Sash member Designation / Type / Item No. Frame joints Supplementary parts Rebate design Rebate drainage Pressure equalisation Infill panel Type / manufacturer Total thickness 1,133 mm x 1,383 mm 68.2 kg further details are given in drawings 1537445 with reinforcing profile 1357542, 23 x 38 x 1.5 mm, 82 x 80 mm mitred and welded further details are given in drawings 1537215 with reinforcing profile 1244526, 35 x 28 x 2 mm, 79 x 80 mm mitred and welded glazing bar 1560311, mitred, clipped 3 slots 5 mm x 28 mm inside rebate, 25 and 30 mm from internal edge of frame to outside front 2 slots 5 mm x 31 mm, 150 and 160 mm from external edge of frame, with cover caps 12615821012 2 slots 5 mm x 26 mm inside rebate, 25 and 30 mm from internal edge of frame to outside 2 slots 5 mm x 31 mm, 135 and 145 mm from external edge of frame insulating glass unit (IGU) triple IGU 46 mm Configuration 3.3.1 CGSolar / 14 thermix / 4 extra clear / 14 thermix / 3.3.1 CGPremium Incorporation of infill panel Vapour pressure equalisation Glazing gasket, external Designation / Type / Item No. PREN 601 Manufacturer Material Glazing gasket, internal at bottom and top 2 slots 5 mm x 30 mm, 105 and 115 mm from external edge of sash Rehau PREN Designation / Type / Item No. PREN 707 Manufacturer Rehau
Evidence of Performance Page 3 of 14 Material PREN External rebate seal frame Designation / Type / Item No. PREN 601 Manufacturer Rehau Material PREN Corner design mitred and welded External rebate seal sash Designation / Type / Item No. PREN 707 Manufacturer Rehau Material PREN Corner design mitred and welded Centre seal Designation / Type / Item No. PREN 601 Manufacturer Rehau Material PREN Corner design mitred and welded Hardware Type / manufacturer tilt and turn hardware, Siegenia Titan AF RC2 Hinges / bearings/pivots 1 tilt mechanism pivot, 1 corner pivot Number of locking devices at bottom 3, at top 2, on hinge side 3, on lock side 3 Locking distance, max. in mm 685 mm Position of locking devices neutral The description is based on information provided by the client and inspection of the test specimen at the ift (item designations / numbers as well as material specifications were provided by the client unless stated "ift-checked ). Test specimen representations are documented in the Annex "Representation of product/test specimen. The design details were examined solely on the basis of the characteristics / performance to be classified. The drawings are based on unchanged documentation provided by the client unless stated otherwise. The photographs were taken by the ift Rosenheim unless stated otherwise. 1.2 Sampling The below sampling data were provided to the ift: Sampling by: SUNCE Marinkovic d.o.o., 34000Kragujevac (Serbia) Date: 30.11.2016 Verification: Delivered on: 12.12.2016 ift specimen No: 16-002359-PK01 A sampling report has been provided to the ift.
Evidence of Performance Page 4 of 14 2 Procedure 2.1 Basis*) referring to methods Testing EN 1026:2000-06 Windows and doors - Air permeability - Test method EN 1027:2000-06 Windows and doors - Watertightness - Test method EN 12046-1:2003-11 Operating forces - Test method - Part 1: Windows EN 12211:2000-06 Windows and doors - Resistance to wind load - Test method Classification / Evaluation EN 12207:1999-11 Windows and doors - Air permeability - Classification EN 12208:1999-11 Windows and doors - Watertightness - Classification EN 12210:1999-11/AC:2002-08 Windows and doors - Resistance to wind load - Classification *) and the equivalent national versions, e.g. DIN EN
Evidence of Performance Page 5 of 14 2.2 Brief description of procedure Air permeability - EN 1026 Prior to testing, the operating forces are determined as per EN 12046-1 for the release / locking operation of the hardware. Air permeability is tested in accordance with EN 1026 and conducted in steps at negative pressure and positive pressure up to the maximum test pressure difference. Leakages of the test set-up are made visible using artificially generated fog and sealed using permanently resilient sealant. The test specimen is exposed to three pressure pulses pmax + 10 % or at least 500 Pa. This is followed by measurement of air permeability for the respective pressure steps. + Pa 3 if required 0 1 Time (sec.) - Pa opening and closing Illustration Test sequence for air permeability
Evidence of Performance Page 6 of 14 Resistance to wind load - Deflection and alternating negative/positive pressures - EN 12211 Resistance to wind load is tested in accordance with EN 12211 and conducted in steps at negative pressure and positive pressure up to the test pressure p 1. The test specimen is exposed to three pressure pulses p 1 + 10 %. This is followed by determination of the frontal deflection of test specimen for each pressure step when exposed to positive test pressure p 1 and negative test pressure p 1. Then the test specimen is subjected to 50 cycles including negative and positive pressures of ± p 2 = p 1-50 %. Positive pressure P 1+10% 30±10 s 50 Cycles P 1 7±3 s P 2 60±5 s 0 -P 2 Stepwise or continuous increase in pressure, max. 100 Pa/s 7±3 s Time -P 1 P 1+10% 30±10 s 7±3 s Negative pressure Illustration Test sequence for resistance to wind load Air permeability Repeat test - EN 1026 Following resistance to wind load test for p 1 (deflection) and p 2 (alternating positive/negative pressure), air permeability must not exceed by more than 20% the upper limit of the specified class as set out by EN 12207.
Evidence of Performance Page 7 of 14 Watertightness - EN 1027 Watertightness is tested in accordance with EN 1027 up to the maximum test pressure difference. The external face of the test specimen is subjected to constant spraying of water by an upper row of nozzles at a flow rate of approx. 2 l/min per nozzle while increments of positive test pressure are applied at regular intervals. For test specimen exceeding 2.50 m in overall height, additional rows of nozzles are fixed at vertical intervals at 1.5 m below the top nozzle line. The water flow rate of the additional nozzle rows is approx. 1 l/min per nozzle. P ( Pa ) 750 600 500 450 400 300 200 150 100 50 0 Illustration 5 10 15 20 25 30 35 40 45 50 55 Test sequence for watertightness Time (min)
Evidence of Performance Page 8 of 14 Resistance to wind load Safety test - EN 12211 The wind resistance test (safety test) is conducted at negative pressure and positive pressure in accordance with EN 12211 up to test pressure p 3 = p 1 + 50 %. Positive pressure 7±3 s P 3 7±3 s 7±3 s 0 Time -P 3 Negative pressure Illustration Test sequence for safety test
Evidence of Performance Page 9 of 14 3 Detailed results
Evidence of Performance Page 10 of 14
Evidence of Performance Page 11 of 14
Evidence of Performance Page 12 of 14
Evidence of Performance Page 13 of 14
Evidence of Performance Page 14 of 14
Annex 1: Representation of product/test specimen Page 1 of 10 Evidence of Performance Drawing 1 Test specimen
Annex 1: Representation of product/test specimen Page 2 of 10 Evidence of Performance Drawing 2 Horizontal section
Annex 1: Representation of product/test specimen Page 3 of 10 Evidence of Performance Drawing 3 Vertical section
Annex 1: Representation of product/test specimen Page 4 of 10 Evidence of Performance Photo 1 Test specimen on test rig window closed Photo 2 Test specimen on test rig window open Photo 3 Rebate drainage Photo 4 Rebate drainage Photo 5 Rebate drainage Photo 6 Rebate drainage
Annex 1: Representation of product/test specimen Page 5 of 10 Evidence of Performance Photo 7 Rebate drainage Photo 8 Rebate drainage Photo 9 Rebate drainage Photo 10 Rebate drainage Photo 11 External rebate seal, corner design Photo 12 External rebate seal
Annex 1: Representation of product/test specimen Page 6 of 10 Evidence of Performance Photo 13 Centre seal, corner design Photo 14 Centre seal Photo 15 Internal rebate seal, corner design Photo 16 Internal rebate seal Photo 17 Pressure equalisation Photo 18 Pressure equalisation
Annex 1: Representation of product/test specimen Page 7 of 10 Evidence of Performance Photo 19 Pressure equalisation Photo 20 Pressure equalisation Photo 21 Pressure equalisation Photo 22 Pressure equalisation Photo 23 Pressure equalisation Photo 24 Pressure equalisation
Annex 1: Representation of product/test specimen Page 8 of 10 Evidence of Performance Photo 25 External glazing gasket, corner design Photo 26 External glazing gasket Photo 27 Internal glazing gasket, corner design Photo 28 Internal glazing gasket Photo 29 View of horizontal glazing rebate Photo 30 Vapour pressure equalisation
Annex 1: Representation of product/test specimen Page 9 of 10 Evidence of Performance Photo 31 Vapour pressure equalisation Photo 32 Vapour pressure equalisation Photo 33 Vapour pressure equalisation Photo 34 Vapour pressure equalisation Photo 35 Tilt mechanism pivot, seen from inside Photo 36 Tilt mechanism pivot, seen from rebate
Annex 1: Representation of product/test specimen Page 10 of 10 Evidence of Performance Photo 37 Corner pivot, seen from inside Photo 38 Corner pivot, seen from rebate Photo 39 Locking situation, frame / sash 1 Photo 40 Locking situation, frame / sash 1 Photo 41 Locking situation, frame / sash 2 Photo 42 Locking situation, frame / sash 2