Company : IDMC PTE TD CHOO'- PHAE 2 Approved by : K.W. Ten (Project Manager) ast Review Date : Chan Bok eng (ite Manager) Next Review Date : Trade / Activities: Mechanical ystem -Install Big Ass Fans 1 3 6 9 2 2 4 6 3 1 2 3 No. Activity / Task Hazard Identified Design Mitigation Index Further Control 1 Transporting / Unload Potential trips & fall from scattered Ensure floor is level and 2 2 4 *Proper housekeeping & daily remove 1 2 2, F of mat'l to ground floor during transporting smooth debris. Protection ext'g floor *tack & standby not more than 3 *Fan motor catton size: 1m 3 plywoods course *Fan Blade Catton size: Ensure no students activities *Traffic guard shall standby during load/ 3.3m x 0.2m x 0.4m unload. 2 Drilling the wall for Falling from height object are screw, Used pipe clip instead of 2 2 4 *Ensure proper working platform is 1 2 2, F conduit / piping tools and etc. drilling provided (cissors lift) concealment and surface Prepare cutting off site *Using of appropriate PPE (afety hardness & glove) *Worker are trained & briefed on the Manual cutting pipes / safety procedures to follow while bracket working at height * Area of operation cordoned off and in place * Moving part of power tools to be guarded (hand drilled) are annually inspect by EW before used 1 2 3 - ifting upervisor - afety upervisor Pg. 1/3 ow Risk ( 1, 2 )
Company : Approved by : 3 6 9 2 4 6 1 2 3 Index Further Control 3 aying control cable into truck by lifted object or cable twist Prepare off site and cut 2 2 4 Ensure below working area no objective 1 2 2, F conduit is installed extra length block 4 Fixing of Fans motor and Potential fall from lifted during Used manual lifting jack 2 2 4 *Ensure wire rope is secure on top steel 1 2 2, F fans blade installed c/w safety cable and gripple structural or steel pole *Keep lifting height within design mfg. *Fan motor operate wt: 120kg * Fan blade wt: 5.5kg IDMC PTE TD CHOO'- PHAE 2 K.W. Ten (Project Manager) No. Activity / Task Hazard Identified Design Mitigation Chan Bok eng (ite Manager) ast Review Date : Next Review Date : ow Risk ( 1, 2 ) criteria or match with hi-bay light * Ensure worker wear hand glove and safety hardness is proper wear and anchor to steel structural or steel pole *tand by proper tools is suitable used (Box spanner & link spanner) building material. 1 2 3 1 2 3 a)fixing upper/lower York and extension pole - ifting upervisor - afety upervisor Potential fall from lifted during Used manual lifting jack 2 2 4 * Ensure area is cordon-off with 1 2 2, F installed with safety cable c/w gripple * ecure the safety cable by *tand by proper tools is suitable used wrapping it all round the light & prinkler piping. I-beam c/w loop end with shackle Pg. 2/3
Company : IDMC PTE TD CHOO'-PHAE 2 Approved by : K.W. Ten (Project Manager) Chan Bok eng(ite Engrg) ast Review Date : Next Review Date : ow Risk ( 1, 2 ) 1 2 3 1 2 3 3 6 9 2 4 6 1 2 3 No. Activity / Task Hazard Identified Design Mitigation Index Further Control b) ifting fan motor Potential fall from scattered during Used manual lifting jack 2 2 4 * Ensure area is cordon-off with lifting & installing with safety cable c/w 1 2 2, F gripple * ecure the safety cable by *tand by proper tools suitable used wrapping it all round the light & prinkler piping. motor frame and extend pole c/w loop end with shackle c) ifting fan blade c/w Potential fall from slotting into fan motor *lide fan blade onto fan 2 2 4 * Ensure area is cordon-off with winglet during installing hub with secure bolt 1 2 2, F wt: 5.5kg each & nuts include retainers *lide in one-by-one *tand by proper tools is suitable used light & prinkler piping. d) QP certify supervision Protential fall from miss bolt & nuts tighten Used proper tools to check 2 2 4 * Ensure area is cordon-off with 1 2 2, F as manufacture specifications all bolt and nuts are tighten with torque wrench *tand by proper tools is suitable used - ifting upervisor - afety upervisor Pg. 3/3 ow Risk ( 1, 2 )