Hawk Mechanical Alley Submittal Log - Hawk Job #: 65 //04 Submittal Status Section Sub-Section Tag Description Manufacturer Model # Approval Status Submitted Revision Returned 4900 4900 Facility Natural Gas Piping. B - Quick-Disconnect Devices Dormont 00-00 Outdoor Flex & Disconnect Revised & Resubmit //04 4900. E - Waterproof Vent Cap Beckett Mushroom Vent Cap Revised & Resubmit //04 4900.4-A- B- & B- Pressure Reducing Valves American Meter -/" Model 8 Revised & Resubmit //04 4900.4-A- BR- & BR- Pressure Reducing Valves American Meter -/4" Model 8C Revised & Resubmit //04 4900.4-A- AHU Pressure Reducing Valves American Meter -/4" Model 8C Revised & Resubmit //04 4900.4-A-4 FIREPLACE & PIT Pressure Reducing Valves American Meter /4" Model 8C Revised & Resubmit //04 4900.6-A- GM- Gas Sub-Meter: Hydronic Boilers Dresser w/ Riotronics " Model 5M75 w/ Pulser Revised & Resubmit //04 4900.6-A- GM- Gas Sub-Meter: Domestic Boilers Dresser w/ Riotronics " Model M75 w/pulser Revised & Resubmit //04 4900.6-A- GM- Gas Sub-Meter: AHU American Meter -/4" AC60 w/cmc- Pulser Revised & Resubmit //04
SUBMITTAL REVIEW COVERSHEET Project Name: Alley 75 Westlake Avenue N. Date: 0-- Suite 00 Submittal No & Description Submittal #00-4900-0 Natural Gas Materials Seattle, WA 9809 06-85- Submittal Date: 0--05 Submittal Status: No Exception Taken (NET) Exception Taken as Noted, Provide Revised Submittal for Project Records, No Add l Rushing Review Req d (ET) Exception Taken as Noted, Revise and Resubmit as Noted for Rushing Review (ET-RR) Review is only for general conformance with the project design concepts and general compliance with the information given in the contract documents. The contractor remains responsible for full compliance with the contract drawings and specifications, confirmation of all project specific dimensions, fabrication processes, techniques of construction, coordination of work with that of all other trades, and the satisfactory performance of their work. Revision History: Rev 0 Date: 0-- By: Steven Huff E-mail: StevenH@rushingco.com Comments: Status 0- No exception taken with submitted products unless specifically noted below. INFO 0-0- 0-4 0-5 Quick Disconnect the submitted Dormont product is for indoor use only. Provide submittal for quick disconnect device listed for use both indoor and outdoor OR provide additional submittal for product rated for outdoor use. Weatherproof vent cap Product has not been included in submittal. Provide product submittal for review. Gas Pressure Regulator: Specify which model(s) will be provided, including orifice size and spring range. Provide with vent limiter where regulators are to be installed in corridors. Sage Prime Gas Flow Meters: No exception taken with submitted products. Ensure that meters are purchased with any accessories required to be compatible with building BMS system. ET-RR ET-RR ET-RR NET END OF REVIEW
COUNTERTOP & PORTABLE OUTDOOR GAS APPLIANCE CONNECTORS Countertop Gas Connectors Dormont gas connectors for countertop applications offer the same benefits of safety, durability and cleanliness provided by Blue Hose connectors. Feature stainless steel tubing construction, tight-weave stainless steel braid, and an antimicrobial PVC coating. Meet ANSI Z.69/CSA 6.6 code requirements for countertop appliance connections. NOTE: This item sold in packs of six. BTU/hr ID PART # Stationary Hose Countertop Elbow Elbow 0k /" CT6 50k /" CT4 Full- Port Valve 0k /" CTKIT6 50k /" CTKIT4 Minimum Flow Capacity (0.64 Sp. Gr., 000 BTU/ft Natural Gas at 0.5 w.c. pressure drop) Flexible corrugated stainless steel construction Tight weave stainlesss steel braid for reinforcement Smooth easy to clean antimicrobial PVC coating Portable Outdoor Connectors for Natural Gas and LP Appliances Dormont provides natural gas and liquid propane gas connectors that are specifically designed for outdoor applications. These connectors are outfitted with special quick disconnect fittings that make disconnecting and reconnecting your outdoor appliances to a gas supply line or tank safe and quick. Connect outdoor NG or LP appliances to a gas supply source. Allow movement of gas appliance around outdoor living space. Includes easy-to-use, time-saving quick disconnect. Pressure and Temperature: Working Pressure: / psi /.04 bar Max Temp: 00ºF / 9ºC; Min Temp: -40ºF/ -40ºC Gas Hose Connector listed to ANSI Z.54/CSA 8.4 Quick Disconnect listed to ANSI Z.4/CSA 6.9 PART # Gas ID Connector Type and Size Length ft /m 0D-0QD NG / LP /8" /8" female flare x /8" female NPT QD 0D-QD NG / LP /8" /8" female flare x /8" female NPT QD 0D-0QD NG / LP /" /" female flare x /" female NPT QD 0D-QD NG / LP /" /" female flare x /" female NPT QD 0 /.05 /.66 0 /.05 /.66 () 67-6668 dormont.com 7
Visit us on-line at: www.beckettcorp.com/oiltankaccessories VENT CAPS Available in threaded and slip-on designs Slip-On design solves clearance problems Rust-resistant zinc plated steel and cast iron, as-well-as rust-proof aluminum and zinc castings Available in sizes from to 4 Each cap includes a screen, to prevent debris from entering the vent pipe -/4 Minimum vent to meet NFPA Requirements Mushroom Vent Caps This popular style is used in the majority of installations in the United States, Alaska, and Canada Available in female NPT sizes from to 4 Each cap is designed with a 0 mesh screen, to prevent debris from entering the vent pipe Mushroom Vent Caps Part No. Female NPT 40 40 -/4 404 -/ 405 407 408 4 Slip-On Vent Caps Zinc plated steel with screen Lightweight and economical Slip-On Vent Caps Part No. 405 Zinc Slip-On Cap Beckett s most economical design Zinc alloy won t rust Slip-on design Only requires ~/6 pipe-to-wall clearance Supplied with set screw and wire screen Available in sizes from /4 to -/ Zinc Slip-On Vent Caps Part No. Pipe Size 4006 /4-4008 -/ Aluminum Slip-On Cap Ideal for close-to-wall Installations. Requires only ~/8 pipe-to wall clearance Rust proof cast aluminum design includes an integral screen Cap is secured to pipe using a single set screw Aluminum Slip-On Vent Caps Part No. 4006 Part No. Pipe Size Part No. Pipe Size 406 4009 407 -/4 408 -/ 409 Part No. 409 Part No. 4009 4 R.W. Beckett Corporation Mail: PO Box 89 - Elyria, OH 4406 - Ship: 85 Center Ridge Rd. - N. Ridgeville, OH 4409.645.876 Fax:..980 www.beckettcorp.com/oiltankaccessories
A C E D SB 8540. Industrial Regulator Series /000 AMC Quality System QMI is Accredited by: C R E D I T ISO 900 Registered R E ANSI RAB G I S T R A R Dutch Council for Accreditation Measurement Engineers Since 86
American Meter Series and 000 Worker/Monitor Regulators Worker/Monitor sets are commonly used to provide overpressure protection. A worker/monitor installation consists of a monitor with an external static connection and a worker with an internal static connection. The regulator selected to be the monitor is set at " to 5" w.c. above the worker. The external static connection is connected at a point free of turbulence and preferably a minimum of five pipe diameters downstream. Improved Features and 000 Series Monitor Conversion American Meter offers four industrial monitor regulators the 80M, 00M, 88M and 08M. Design improvements now enable all models to be configured as Monitor Regulators. This change was effective with all and 000 Series Regulators manufactured after January 994. The advantage is that two models of the same regulator need not be stocked. All models are pre-machined to accept a monitor conversion kit. Refer to IMP 8740 for kit numbers and installation instructions. When a regulator with an OPSO is converted to a monitor, a sense line must extend downstream of the worker, as shown in the diagram to the right. CONTROLLING MONITOR /" Typical Upstream Monitor Installation
The American Meter Industrial Regulator Monitor Conversion The body and valve head are premachined to allow easy conversion to a monitor model. See page for more information. Rugged Construction Valve heads are ductile iron which prevents thread damage. Available as -/" and " screwed, and " flanged connections. ANSI, BSP and DIN connections available. Springs The Series spring ranges from.5" w.c. to 5 psi outlet pressure. 000 Series spring ranges from / psi to 5 psi outlet pressure. See page. Interchangeable Available in sizes from /4" through -/4" for a wide range of flow rates. One orifice is offered for both standard and OPSO models to minimize spare-parts inventory. OPSO Overpressure Shutoff for positive protection of public buildings such as schools, churches, etc. See page 5. Maintenance Three setscrews hold diaphragm case to the valve head, providing the easiest orifice and seat disc inspection in the industry. Pressure Taps The and 000 Regulators have inlet and outlet pressure taps. Relief Vent A " vent for Full Relief overpressure protection in three models, such as the 8B. Partial Relief has " vent and 000 Series has /4". See page 7 for relief performances. Durability Cast-aluminum top and bottom diaphragm case for long service life. UPSO Snap-acting lever for underpressure shutoff protection when line pressure drops drastically.
American Meter Regulators Other Features 8 Partial Relief Series low-pressure models have a maximum inlet pressure of 50 psi and offer outlet pressures ranging from.5" w.c. to 5 psi. 000 Series high pressure models allow a maximum inlet pressure of 50 psi and outlet pressures ranging from.5 psi to 5 psi. The Series can be ordered as Full Relief, Partial Relief or No Relief Regulator as shown in the table. 000 Series Regulators are non-relieving. Both models are available with Overpressure Shutoff, Underpressure Shutoff and monitor capabilities. Low Pres. Model Dimensions Numbers Description A B C D *E 80 Standard Regulator.75" ".75" 6" 0.5" 80M Standard Monitor Regulator.75" ".75" 6" 0.5" 8 Partial Internal Relief Regulator.75" ".75" 6" 0.5" 8B Full Capacity Internal Relief Regulator.75" ".75" 6" 0.5" 8 Underpressure Shutoff.75" ".75" 6" 0.5" 8 Underpressure Shutoff with Partial Internal Relief.75" ".75" 6" 0.5" 8B Underpressure Shutoff with Full Internal Relief.75" ".75" 6" 0.5" 84 Overpressure Shutoff with Partial Internal Relief.75" " 5.6" 9.87" 0.5" 84B Overpressure Shutoff with Full Capacity Internal Relief.75" " 5.6" 9.87" 0.5" 85 Overpressure and Underpressure Shutoff with Partial Internal Relief.75" " 5.6" 9.87" 0.5" 85B Overpressure and Underpressure Shutoff with Full Capacity Internal Relief.75" " 5.6" 9.87" 0.5" 88 Overpressure Shutoff.75" " 5.6" 9.87" 0.5" 88M Overpressure Shutoff with Monitor.75" " 5.6" 9.87" 0.5" 89 Overpressure and Underpressure Shutoff.75" " 5.6" 9.87" 0.5" High Pres. Model Dimensions Numbers Description A B C D *E 00 Standard Regulator 8.9" ".75" 6" 0.5" 00M Standard Monitor Regulator 8.9" ".75" 6" 0.5" 0 Underpressure Shutoff 8.9" ".75" 6" 0.5" 08 Overpressure Shutoff 8.9" " 5.6" 9.87" 0.5" 08M Overpressure Shutoff with Monitor 8.9" " 5.6" 9.87" 0.5" 09 Overpressure and Underpressure Shutoff 8.9" " 5.6" 9.87" 0.5" *A 0" flange valve head is an option; contact Sales Office for information. 00 No Relief Low Pressure A B E B C High Pressure A B E B C D D 4
-/" Series Capacity Data SCFH Gas 0.60 Specific Gravity SPRING NO. 744P07.5" to 6" w.c. Set: 6" w.c. Droop: " w.c. Max. Compound: " w.c. SPRING NO. 744P09 8.5" to 4" w.c. Set: " w.c. Droop: " w.c. SPRING NO. 744P00 4.5" to 8" w.c. Set: psi Droop: 6" w.c. SPRING NO. 744P0 psi to psi Set: psi Droop: 0.6 psi Size All Models With Silver Holder psi Size All Models With Silver Holder -/4" " 7/8" /4" 5/8" /" /8" /4" -/4" " 7/8" /4" 5/8" /" /8" /4",000,600,00,00 900 /,900,,00,00,000 600,850,00,00,,400,00 750,750,00,850,,00,50,,50,900,,000,,00,750,00,600,600,000,,00 4,,900,400,400,,00,400 4,,900,00,00,,00,00 5, 5,00 4,400 4,00,00,900,000,00 5 5, 5,00 4,00 4,000,400,950,,000 7, 6,00 6,00 4, 4,400,000, 0 7,400 6,00 6,000 5,000 4,400,000,600 9,00 7,900 7, 6,00 5,400,850,900 5 9,50 7, 7, 6,00 5,,850,900 9,00 8, 7,00 6,00 4,600,00 0 9,00 8,600 7,50 6,400 4,,00,750,00 9,000 7, 5,900,850 0, 0, 8,900 8,00 5,,,00 0, 9,00 7,00,400 40,00,000 9,00 7,50,400,000 9,400 4, 60,000 9,400 4, 5,850 80 5, 7,000 00 7,000 8,400 5 8,00 Size All Models With Silver Holder psi Size All Models With Silver Holder -/4" " 7/8" /4" 5/8" /" /8" /4" -/4" " 7/8" /4" 5/8" /" /8" /4",,00 4,00, 5, 4,000 6,00 5,00 8,000 7,600 9,00,900,, 4, 6,600 8,00 9,,,,00 4,00 6,00 7, 9,000,00,000,,600 5,00 6, 7,50,00,,00, 4,00 5,400 6, 750,00,400,000,900, 4,,000,,850,50 5 0 5 0,,00,,00 4,750 4,000 5, 5,400 8,00 7, 9,400,,600,00 4,400 6,400 8,000 9,600,,400,00 4,00 6,00 7,600 8,,00,900,,00 4,900 6,50 7,,000,,000,600 4,00 5,00 6,00,000,50,,, 4,00,000,,900,00,00,00 9,00 8,00 5,, 0,00,00 9,400 8,000 5,600,,,400 9, 7,00,00 40,,00 9,00 7,00,00,900, 9,600 4, 60,,00 9,400 4, 4,00, 5, 7,000 8,00 80 00 5 4,000, 5, 7,000 8,00 Size All Models With Silver Holder psi Size All Models With Silver Holder -/4" " 7/8" /4" 5/8" /" /8" /4" -/4" " 7/8" /4" 5/8" /" /8" /4" 6,00 4,900 4,00,400,000,00, 8,000 6, 5,600 4, 4,00,00,000,000 5 7,00 5, 4,900 4,400,600,,750 900,000 9,400 8,00 7,000 6,00 4,900,, 0,000 9,00 7, 7,000 5,900 4,,900,,00 0,000 8, 7, 6,00,,900 5,000, 9,750 8, 7,600 6,00,,900,,400 0,000 9,00 7,00 4,00,50 0 4,900,,900 0, 9, 7,400 4,,00 4,00,00,600 9,00 5,600, 0 5,400 4,850,00,00 9, 6,000, 5,600,900, 0,900 7,00,400 40 7,000 5,00,850,600 7,00,400 6,400 6,000 4,00 9,00 4, 60 9,600 8,00 7,00 5,000 9, 4,600 6,000, 5, 80 0,000 8,900 7,, 5,, 7,000 00, 7,000 8,400 5 8,400 Size All Models With Silver Holder psi Size All Models With Silver Holder -/4" " 7/8" /4" 5/8" /" /8" /4" -/4" " 7/8" /4" 5/8" /" /8" /4" 4,00,400,900,900,000,000,00 750 5 7,600 5, 5,000 5,000,,,00,400 0 7,000 5,600 4, 4,,,00,00,00 0,000 7,900,000 9, 6, 8,00 6, 8,00 4, 5, 4, 5,,000,,600,00 5 0 9, 7,600, 9,750 6,00 7,600 6,00 7,600 4, 6,000 4,00 5,00,000,850,,00,00 0, 0,,400,400 8,000 9, 8,000 9, 4,,900 6,000, 0 40, 0, 0,,000,000 8,00 9,400 7,00 8, 5,000,900 6,, 7,000 7,000,900,900 8,400 4, 60 7,00 7,00,,000 8,900 4,900 0,000 5, 5, 0,850 6,00, 7, 8,00 80 00 5 0,000 6,000 5,00 0, 6,00, 7, 8,00 Size All Models With Silver Holder -/4" " 7/8" /4" 5/8" /" /8" /4" SPRING NO. 4,050,400,400,,00,,400 744P06 7,00 5, 5,000 4, 4,,,00,00 8,640 7,400 6,00 5, 5,,,000,600.5 to.5 psi 9,090 8,600 7,000 6, 6, 4,,,000 Set:.5 psi 0,600 8, 8, 8,00 5,900 4,,600 Droop: 0.4 psi,00,400 9, 6,900 5,600,00 4,00,,00 0,00 7,400 4,00 4,,,00 9,400 5,400 0, 6,00 7, For optimum performance, regulator should be operated above solid line. For UPSO Models, use only above dashed line. psi 5 0 5 0 0 40 60 80 00 5 7 SPRING NO. 744P08 5.5" to 8" w.c. Set: 7" Droop: " Max. Compound: " w.c. SPRING NO. 744P09 8.5" to 4" w.c. Set: 4" Droop: " w.c. SPRING NO. 744P0 psi to psi Set: psi Droop: 0.4 psi SPRING NO. 744P0 psi to 5 psi Set: 5 psi Droop: psi Contact your American Meter representative for inlet pressures above 5 psi.
C and C-HC Series Service Regulators Technical Bulletin
C and C-HC Series Service Regulators 0 Elster American Meter The C Series pressure regulators are designed to control natural gas, air, nitrogen, carbon dioxide, propane vapor, and other non-corrosive gases in residential, light commercial, and small industrial applications. General Information Outlet pressures between.5" W.C. and PSIG are available. Operating temperature range is -0 F to 50 F (-0 C to 65 C). Maximum flow rate is SCFH (70.8 m /h). All models conform to ANSI Code B09.4-998, and CGA Service-Type Regulator Specification CAN/CGA-6.8-M95. Features Variety of interchangeable orifices and spring ranges 90 Degree (Right Angle), 80 Degree (Straight-Flow), or Offset Valve Body (See photo below) Wide range of valve body connection sizes Options Vent Elbow The regulator vent opening should face downward (6 o'clock) to minimize the chance of blockage from ice and snow. If not possible, a /4" NPT plastic, 90 vent elbow (part number 7804P05) and separate protective screen (part number 70400P07) may be screwed into the vent to provide the necessary protection. Elevation Compensation The E.C. orifice is recommended for installations where the inlet pressure may vary over a wide range. The E.C. orifice is available in two sizes: /8" x /6" and /6". The capacities of these orifices are the same as the standard orifice of the same size. Full Capacity Relief Valve Full capacity internal relief valve standard on all models. (See Performance Graphs on page 9) Splashguards UV stabilized, weather-resistant, resin device that protects the vent screen from Applications Model Number 8C 8C-HC 84C 84C-HC 85C w/ USSA 85C-HC w/ USSA splashes while providing a large external vent opening to keep regulators working properly. Safety Shutoff Devices Overpressure Shutoff (OPSO) Operates independently. The OPSO will shut off the gas supply in the event of a serious downstream pressure build-up. These are available in two pressure ranges on the Models 84C and 84C-HC. Spring Range Part Number 4" W.C. to 5" W.C. 740P005 PSIG to / PSIG 740P004 When the outlet pressure exceeds the OPSO set point, the pressure under the OPSO diaphragm (A) compresses the pressure spring (B) forcing the diaphragm stem (E) upwards and releasing plunger (D). This permits the shut-off spring (F) to force the shut-off disc (G) against the back side of the special double-ended orifice. E D C H A OPSO Diaphragm Plate B Pressure Spring C Cap D Plunger E Diaphragm Stem F Shut-off Spring G Shut-off Disc H Adjusting Screw B A F G Spring Range Description Basic regulator with full-capacity internal relief with /4" or " NPT vent. Basic regulator with full-capacity internal relief with /4" or " NPT vent. Basic regulator with full-capacity internal relief and overpressure shut-off and /4" or " NPT vent. Basic regulator with full-capacity internal relief and overpressure shut-off and /4" or " NPT vent. Basic regulator with full-capacity internal relief and overpressure, underpressure shut-off and /4" or " NPT vent. Basic regulator with full-capacity internal relief and overpressure, underpressure shut-off and /4" or " NPT vent. Universal Safety Shutoff Assembly (USSA) USSA protects the downstream piping from both over- and under-pressure conditions by shutting off the gas flow at the inlet side of the regulator orifice. Both Over- and under-pressure shut-off set points are adjustable depending on spring ranges selected. USSA Shutoff Spring Ranges Over Pressure Spring Ranges Part Number 7.5-4 W.C. 7P 0 - W.C. 7P4 4-44 W.C. 7P5 40-84 W.C. 7P6-5 PSIG 7P7 4-7 PSIG 7P8 Under Pressure Spring Ranges Spring Range Part Number - 6 W.C. 7P 6-4 W.C. 7P4 4-60 W.C. 7P5 Pressure Taps /8" NPT taps are available on most valve heads. Offset Valve Body
C and C-HC Series Service Regulators 0 Elster American Meter 9 4 5 4 5 0 6 8 Material Specifications Outlet Pressure 7 6 Diaphragm Case - Precision die-cast aluminum with an exclusive sevenstep advanced conversion coating, single-coat polyester primer and high solids polyurethane top coat. Valve Body - Cast grey iron, undercoated, single coat polyester primer and high solids polyurethane top coat. NPT threads meet ANSI/ ASME B.0.. BSP-TR threads meet BS EN 06. Available sizes: /4 x /4, /4 x, /4 x -/4, x, x -/4 and -/4 x -/4 NPT or BSP-TR Offset valve body: /4 x /4, /4 x and x NPT or BSP-TR Pressure Spring - Steel, zinc plated and yellow chromate. Color coded for identification. Color Code Part Number.5" to 6" W.C. Blue 7P04.5" to 7.5" W.C. Tan 7P089 5.5" to 8.5" W.C. Yellow 7P044 6" to " W.C. Brown 7P7 6" to 5" W.C. Purple 7P04 " to 8" W.C. White 7P060 4" to 48" W.C. Red 7P08 4" W.C. to PSIG Red - Red 7P049 4 Diaphragm Plate - Steel, Electrogalvanized. 5 Diaphragm - Buna N; Nylon fabric reinforced. 6 Seat Disc - Buna N; 60, 70 (std.) or 80 durometer rating. 7 Valve - High strength, corrosion resistant aluminum. Size Standard Part Number Part Number with OPSO 9/6" 7494P06 775P09 /" 7494P05 775P06 /8" 7494P0 775P04 5/6" 7494P0 775P0 /4" 7494P0 775P0 /6" 7494P00 775P0 /8" x /6" 7494P00 775P00 /8" 7494P09 N/A 8 Lever - Stamped aluminum. 9 Seal Plug - Polyester thermoplastic UV stabilized. 0 Plunger Valve/Plunger Guide - Minlon. Pressure Adjustment Screw - Minlon. Relief Valve Stem - Minlon. Vent Screen - Stainless Steel - All models are designed with a removable weather and bug-proof stainless steel screen to resist freezeups and to exclude foreign matter. The vent is threaded ¾ or NPT (BSP-TR threads available). Inside installation requires a vent line of sufficient diameter to carry gas vented by the regulator to a safe outside location away from any opening(s) in the structure. Comply with applicable Federal, State and local codes. 4 Vent Valve - Stainless Steel with Electrogalvanized steel retainer. 5 Relief Valve Spring - Steel, zinc plated and yellow chromate. Color coded for identification. Non-adjustable, standard set point of 8" w.c. above outlet set pressure of 7" w.c. Standard set point of. PSIG above outlet set pressure of PSIG. 6 Lever Pin - Carbon steel, zinc plated and yellow chromate.
C and C-HC Series Service Regulators 04 Elster American Meter C Series Regulator Capacity Performance /4" Outlet Set Point 7.0" W.C. (7.4 mbar) at 50 SCFH SCFH (m /h) 0.60 specific gravity gas at 60 F and 4.7 PSIA (0 C and.0 bar). Pressure spring 7P044. Outlet pressure variance not to exceed +" -" W.C. from set point, horizontal position. C Series Regulator Capacity SCFH (m /h) PSIG (bar) (0.07) (0.4) (0.) 5 (0.4) 0 (0.70) 5 (.00) 0 (.40) 0 (.0) 40 (.80) 60 (4.0) 00 (6.90) 5 (8.60) /8" x /6" 75 (7.8) 75 (0.6) (.7) (4.) (9.8) (.7) 00 (.) (48.) 00 /6" 75 (5.0) 00 (8.5) 75 (0.6) (4.) 750 (.) 950 (6.9) 00 (.) 400 (9.6) (48.) 00 (65.) /4" 50 (7.) 45 (.0) (4.) (9.8) 00 (.) 400 (9.6) (48.) 000 (56.6) 400 (68.0) 5/6" 5 (9.) 475 (.5) 600 (7.0) (.7) 00 (4.0) (4.5) (48.) 00 (6.) /8" 50 (5.6) (9.8) 950 (6.9) 400 (9.6) 600 (45.) 900 (5.8) 400 (68.0) /" 400 (.) (8.4) (.7) 000 (8.) (4.5) 900 (5.8) 00 (6.) 9/6" 400 (.) (8.4) (.7) 00 (4.0) (48.) 000 (56.6) 00 (65.) For optimum performance, maximum inlet pressure should not exceed maximum capacity rating for any given orifice size. " Outlet Set Point 7.0" W.C. (7.4 mbar) at 50 SCFH SCFH (m /h) 0.60 specific gravity gas at 60 F and 4.7 PSIA (0 C and.0 bar). Pressure spring 7P044. Outlet pressure variance not to exceed +" -" W.C. from set point, horizontal position. C Series Regulator Capacity SCFH (m /h) PSIG (bar) (0.07) (0.4) (0.) 5 (0.4) 0 (0.70) 5 (.00) 0 (.40) 0 (.0) 40 (.80) 60 (4.0) 00 (6.90) 5 (8.60) /8" x /6" 50 (7.) 50 45 (.0) (4.) 600 (7.0) 750 (.) 000 (8.) 600 (45.) 000 (56.6) /6" 75 (5.0) 50 (7.) 00 (8.5) (.7) (9.8) 900 (5.5) 00 (.) 400 (9.6) (48.) 400 (68.0) /4" 50 (7.) 50 (.7) (8.4) 000 (8.) 400 (9.6) (48.) 00 (65.) 5/6" 00 (8.5) (.7) (5.6) 750 (.) 400 (9.6) 900 (5.8) 00 (65.) /8" 75 (0.6) (4.) (9.8) 950 (6.9) 600 (45.) 00 /" 475 (.5) 600 (7.0) 850 (4.) 00 (4.0) 900 (5.8) 9/6" (4.) (8.4) 950 (6.9) 00 (6.8) 000 (56.6) For optimum performance, maximum inlet pressure should not exceed maximum capacity rating for any given orifice size.
C and C-HC Series Service Regulators 05 Elster American Meter C Series Regulator Capacity Performance -/4" Outlet Set Point 7.0" W.C. (7.4 mbar) at 50 SCFH SCFH (m /h) 0.60 specific gravity gas at 60 F and 4.7 PSIA (0 C and.0 bar). Pressure spring 7P044. Outlet pressure variance not to exceed +" -" W.C. from set point, horizontal position. C Series Regulator Capacity SCFH (m /h) PSIG (bar) (0.07) (0.4) (0.) 5 (0.4) 0 (0.70) 5 (.00) 0 (.40) 0 (.0) 40 (.80) 60 (4.0) 00 (6.90) /8" x /6" /6" 00 (5.7) 5 (9.) 45 (.0) 75 (7.8) 75 (0.6) (.7) (5.6) (9.8) (.7) 00 (.) 400 (9.6) (5.6) 850 (4.) 000 (8.) 00 (4.0) 600 (45.) /4" 5 (9.) (4.) (8.4) 000 (8.) (4.5) (5.0) 00 5/6" 50 600 (7.0) 950 (6.9) 600 (45.) 400 (68.0) /8" 75 (0.6) (9.8) 00 (4.0) 00 /" 475 (.5) 950 (6.9) (48.) 9/6" (4.) 400 (9.6) 900 (5.8) For optimum performance, maximum inlet pressure should not exceed maximum capacity rating for any given orifice size. /4" Outlet Set Point PSIG (0.4 bar) at 50 SCFH SCFH (m /h) 0.60 specific gravity gas at 60 F and 4.7 PSIA (0 C and.0 bar). Pressure spring 7P049. Outlet pressure variance not to exceed +/- 0% from set point, horizontal position. C Series Regulator Capacity SCFH (m /h) PSIG (bar) (0.) 5 (0.4) 0 (0.70) 5 (.00) 0 (.40) 0 (.0) 40 (.80) 60 (4.0) 00 (6.90) 5 (8.60) /8" x /6" 50 (4.) 50 (7.) 75 (0.6) (.7) (5.6) (9.8) 850 (4.) 00 (.) (48.) 00 /6" 75 (5.0) 5 (9.) (5.6) 750 (.) 900 (5.5) 00 (4.0) (4.5) 00 /4" 00 (8.5) (.7) (9.8) 900 (5.5) 00 (4.0) (4.5) 000 (56.6) 5/6" 5 (9.) 55 (4.9) 85 (.4) 00 (.) 00 (6.8) (5.0) 00 (6.) /8" 75 (0.6) 575 (6.) 000 (8.) 00 (6.8) 600 (45.) 00 /" 400 (.) (9.8) 00 (4.0) (4.5) 900 (5.8) 9/6" (4.) 750 (.) 00 (6.8) (5.0) For optimum performance, maximum inlet pressure should not exceed maximum capacity rating for any given orifice size.
C and C-HC Series Service Regulators 06 Elster American Meter C Series Regulator Capacity Performance " Outlet Set Point PSIG (0.4 bar) at 50 SCFH SCFH (m /h) 0.60 specific gravity gas at 60 F and 4.7 PSIA (0 C and.0 bar). Pressure spring 7P049. Outlet pressure variance not to exceed +/- 0% from set point, horizontal position. C Series Regulator Capacity SCFH (m /h) PSIG (bar) (0.) 5 (0.4) 0 (0.70) 5 (.00) 0 (.40) 0 (.0) 40 (.80) 60 (4.0) 00 (6.90) 5 (8.60) /8" x /6" 50 (4.) 5 (6.4) 50 45 (.0) (4.) (8.4) (.7) 00 (.) (48.) 00 /6" 5 (6.4) 50 600 (7.0) (.7) 000 (8.) 00 (6.8) (48.) /4" 50 (7.) (.7) 750 (.) 000 (8.) 00 (4.0) (48.) 00 (6.) 5/6" 50 (4.) 850 (4.) 00 (.) 400 (9.6) 000 (56.6) /8" 45 (.0) (8.4) 000 (8.) 400 (9.6) (5.0) /" (5.6) 750 (.) 00 (6.8) (48.) 00 9/6" (5.6) 900 (5.5) (4.5) 000 (56.6) For optimum performance, maximum inlet pressure should not exceed maximum capacity rating for any given orifice size. -/4" Outlet Set Point PSIG (0.4 bar) at 50 SCFH SCFH (m /h) 0.60 specific gravity gas at 60 F and 4.7 PSIA (0 C and.0 bar). Pressure spring 7P049. Outlet pressure variance not to exceed +/- 0% from set point, horizontal position. C Series Regulator Capacity SCFH (m /h) PSIG (bar) (0.) 5 (0.4) 0 (0.70) 5 (.00) 0 (.40) 0 (.0) 40 (.80) 60 (4.0) 00 (6.90) 5 (8.60) /8" x /6" 50 (4.) 5 (6.4) 50 45 (.0) (4.) (8.4) (.7) 00 (.) (48.) 00 /6" 5 (6.4) 50 600 (7.0) 850 (4.) 000 (8.) (4.5) 900 (5.8) /4" 50 (4.) 850 (4.) 00 (4.0) (48.) 5/6" 75 (0.6) 600 (7.0) 00 (.) 600 (45.) 00 (6.) /8" 45 (.0) (9.8) 00 (4.0) 900 (5.8) /" (5.6) 900 (5.5) (48.) 9/6" (5.6) 00 (.) 00 (6.) For optimum performance, maximum inlet pressure should not exceed maximum capacity rating for any given orifice size.
C and C-HC Series Service Regulators 08 Elster American Meter C and C-HC Series Service Regulators - Other Technical Data Full-Open Regulator Relief Capacity For sizing downstream relief valves, use the following formulas to determine the regulator full-open capacity: Critical flow rates Q = 0.5 C x P G Sub-critical flows P Q = C x h G Critical flow occurs when the absolute outlet pressure is less than about / of the absolute inlet pressure. Q C P P h G Maximum capacity of regulator constant (see table below) absolute pressure (PSIA) Outlet absolute pressure (PSIA) Differential pressure Specific gravity of gas Constants C /8" 5 /8" x /6" 5 /6" 57 /4" 98 5/6" 49 /8" 08 /" 5 9/6" 4 Maximum Recommended Pressure Size Pressure (PSIG) 9/6" 0 /" 50 /8" 70 5/6" 5 /4" 5 /6" 5 /8" x /6" 5 /8" 5 This is the maximum inlet the regulator should operate at to insure complete lockup at no-flow conditions. Other Gas Capacities To determine the capacity of these regulators for gases other than natural gas, multiply the values within the capacity tables by a Specific Gravity Conversion Factor (F g). The table below lists this factor for some of the more common gases. Gas Type Specific Gravity Conversion Factor (F g ) Air.00 0.77 Butane.0 0.55 Carbon Dioxide.5 0.6 Nitrogen 0.97 0.79 Propane.5 0.6 To calculate the Conversion Factor for other gases: (F g) = Specific gravity of gas on which the capacity table is based Specific gravity of gas being used Example: If using propane and only having tables based on natural gas, the Specific Gravity Conversion Factor is : (F g) = (F g) = 0.60.5 (F g) = 0.66 Specific gravity of natural gas (0.6) Specific gravity of propane (.5) Regulator Pressure Rating 5 PSIG (8.6 bar) = Maximum recommended inlet pressure for normal service. Maximum recommended pressure may vary with orifice size. 75 PSIG ( bar) = Maximum inlet pressure for abnormal or emergency service, without causing damage to regulator case. PSIG (8 mbar) = Maximum outlet pressure for normal service. 0 PSIG (689 mbar) = Maximum outlet pressure which can be contained by pressure carrying components (no flange leakage to atmosphere except for normal relief action). If regulator is subjected to these conditions, it should be removed from service. 50 PSIG (.5 bar) = Maximum outlet pressure for abnormal service without damage to internal components. If regulator is subjected to these conditions, it should be removed from service.
C and C-HC Series Service Regulators 09 Elster American Meter C and C-HC Series Service Regulators Regulator Relief Valve Performance There are several methods of measuring the relief performance of a regulator. The worst case scenario will occur when the lever is disconnected. The data presented in the tables below represent this condition. Outlet Pressure Relative to Pressure /4" Screened Vent No Vent Pipe Set Pressure 7" W.C. Outlet Pressure - Inches W.C. (mbar) 90 (4) 80 (99) 70 (74) 60 (49) 50 (4) 40 (00) 0 (75) 0 (50) 0 (5) 0 0 0 0 0 40 50 60 70 80 90 00 0 0 0 (.7) (.4) (.) (.8) (.4) (4.) (4.8) (5.5) (6.) (6.9) (7.6) (8.) (9.0) Pressure - PSIG (bar) 9/6 /8 /4 /8 x /6 / 5/6 /6 PSIG PSIG " Screened Vent No Vent Pipe Set Pressure 7" W.C. Outlet Pressure - Inches W.C. (mbar) 90 (4) 80 (99) 70 (74) 60 (49) 50 (4) 40 (00) 0 (75) 0 (50) 0 (5) 0 0 0 0 0 40 50 60 70 80 90 00 0 0 0 (.7) (.4) (.) (.8) (.4) (4.) (4.8) (5.5) (6.) (6.9) (7.6) (8.) (9.0) Pressure - PSIG (bar) 9/6 /8 /4 /8 x /6 / 5/6 /6 PSIG PSIG /4" Screened Vent No Vent Pipe Set Pressure PSIG Outlet Pressure - PSIG (bar) 9 (.6) 8 (.55) 7 (.48) 6 (.4) 5 (.4) 4 (.6) (.) (.4) (.07) 0 0 0 0 0 40 50 60 70 80 90 00 0 0 0 (.7) (.4) (.) (.8) (.4) (4.) (4.8) (5.5) (6.) (6.9) (7.6) (8.) (9.0) Pressure - PSIG (bar) 9/6 /8 /4 /8 x /6 / 5/6 /6 " Screened Vent No Vent Pipe Set Pressure PSIG Outlet Pressure - PSIG (bar) 9 (.6) 8 (.55) 7 (.48) 6 (.4) 5 (.4) 4 (.6) (.) (.4) (.07) 0 0 0 0 0 40 50 60 70 80 90 00 0 0 0 (.7) (.4) (.) (.8) (.4) (4.) (4.8) (5.5) (6.) (6.9) (7.6) (8.) (9.0) Pressure - PSIG (bar) 9/6 /8 /4 /8 x /6 / 5/6 /6
C and C-HC Series Service Regulators 0 Elster American Meter C and C-HC Series Service Regulator Dimensions C F Model 8C - 90 Outlet A B C D E F D /4" /4" -9/6" 9.7mm /4" " -9/6" 9.7mm 8-7/8" 5.4mm 8-7/8" 5.4mm 7-/4" 84.mm 7-/4" 84.mm 4-/8" 04.8mm 4-/8" 04.8mm " 50.8mm " 50.8mm -5/8" 9.mm -5/8" 9.mm E " " -9/6" 9.7mm 8-7/8" 5.4mm 7-/4" 84.mm 4-/8" 04.8mm " 50.8mm -5/8" 9.mm A B Model 8C and 8C-HC - 80 C F Outlet A B C D E F /4" /4" " 5.4mm 8-7/8" 5.4mm 7-/4" 84.mm 4-/8" 04.8mm " 50.8mm -5/8" 9.mm D /4" " " 5.4mm " " " 5.4mm 8-7/8" 5.4mm 8-7/8" 5.4mm 7-/4" 84.mm 7-/4" 84.mm 4-/8" 04.8mm 4-/8" 04.8mm " 50.8mm " 50.8mm -5/8" 9.mm -5/8" 9.mm E A B " -/4" -/8" 8.6mm -/4" -/4" -/8" 8.6mm /4" -/4" -/8" 8.6mm 8-7/8" 5.4mm 8-7/8" 5.4mm 8-7/8" 5.4mm 7-/4" 84.mm 7-/4" 84.mm 7-/4" 84.mm 4-/8" 04.8mm 4-/8" 04.8mm 4-/8" 04.8mm " 50.8mm " 50.8mm " 50.8mm -5/8" 9.mm -5/8" 9.mm -5/8" 9.mm C F Model 8C - Offset Outlet A B C D E F D /4" /4" " 5.4mm /4" " " 5.4mm 8-7/8" 5.4mm 8-7/8" 5.4mm 7-/4" 84.mm 7-/4" 84.mm 4-/8" 04.8mm 4-/8" 04.8mm " 50.8mm " 50.8mm -5/8" 9.mm -5/8" 9.mm E " " " 5.4mm 8-7/8" 5.4mm 7-/4" 84.mm 4-/8" 04.8mm " 50.8mm -5/8" 9.mm A B Model 84C and 84C-HC C F Outlet A B C D E F /4" /4" 4-/" 4.mm 8-5/6" 7.0mm 7-/4" 84.mm 4-/8" 04.8mm " 50.8mm -5/8" 9.mm D /4" " 4-/" 4.mm 8-5/6" 7.0mm 7-/4" 84.mm 4-/8" 04.8mm " 50.8mm -5/8" 9.mm E A B " " 4-/" 4.mm " -/4" 4-/" 4.mm 8-5/6" 7.0mm 8-5/6" 7.0mm 7-/4" 84.mm 7-/4" 84.mm 4-/8" 04.8mm 4-/8" 04.8mm " 50.8mm " 50.8mm -5/8" 9.mm -5/8" 9.mm -/4" -/4" 4-/" 4.mm 8-5/6" 7.0mm 7-/4" 84.mm 4-/8" 04.8mm " 50.8mm -5/8" 9.mm
C and C-HC Series Service Regulators Elster American Meter Regulator Assembly Positions 80 Models Valve Head Position "A" Valve Head Position "B" 4 Standard Vent Position 4 Standard Vent Position Valve Head Position "C" Valve Head Position "D" 4 AC-50 Meter with 8C Regulator Standard Vent Position 90 Models Valve Head Position "A" 4 Standard Vent Position Valve Head Position "C" Valve Head Position "D" Standard Vent Position Offset Models 4 4 Standard Vent Position Valve Head Position "B" 4 Standard Vent Position Valve Head Position "D" 4 VENT Standard Vent Position Example of Regulator Assembly Position In the photo above the 8C Regulator shown has an 80 degree valve head in Position "C" (Flow upward) with the vent in position (Looking down). This would be assembly position C. Ordering Information Model number Size of inlet and outlet pressure, PSIG (bar) 4 Outlet pressure, inches w.c. (mbar) or PSIG (bar) 5 Flow, scfh (m/h) 6 Kind and specific gravity of gas 7 size 8 Regulator assembly position number 9 Possible variation in inlet pressure for E.C. models Maximum PSIG (bar) Minimum PSIG (bar) Shipping Weight 7.5 lbs/carton of four regulators 4 Standard Vent Position
C and C-HC Series Service Regulators Technical Bulletin
C and C-HC Series Service Regulators 0 Elster American Meter The C Series pressure regulators are designed to control natural gas, air, nitrogen, carbon dioxide, propane vapor, and other non-corrosive gases in residential, light commercial, and small industrial applications. General Information Outlet pressures between.5" W.C. and PSIG are available. Operating temperature range is -0 F to 50 F (-0 C to 65 C). Maximum flow rate is SCFH (70.8 m /h). All models conform to ANSI Code B09.4-998, and CGA Service-Type Regulator Specification CAN/CGA-6.8-M95. Features Variety of interchangeable orifices and spring ranges 90 Degree (Right Angle), 80 Degree (Straight-Flow), or Offset Valve Body (See photo below) Wide range of valve body connection sizes Options Vent Elbow The regulator vent opening should face downward (6 o'clock) to minimize the chance of blockage from ice and snow. If not possible, a /4" NPT plastic, 90 vent elbow (part number 7804P05) and separate protective screen (part number 70400P07) may be screwed into the vent to provide the necessary protection. Elevation Compensation The E.C. orifice is recommended for installations where the inlet pressure may vary over a wide range. The E.C. orifice is available in two sizes: /8" x /6" and /6". The capacities of these orifices are the same as the standard orifice of the same size. Full Capacity Relief Valve Full capacity internal relief valve standard on all models. (See Performance Graphs on page 9) Splashguards UV stabilized, weather-resistant, resin device that protects the vent screen from Applications Model Number 8C 8C-HC 84C 84C-HC 85C w/ USSA 85C-HC w/ USSA splashes while providing a large external vent opening to keep regulators working properly. Safety Shutoff Devices Overpressure Shutoff (OPSO) Operates independently. The OPSO will shut off the gas supply in the event of a serious downstream pressure build-up. These are available in two pressure ranges on the Models 84C and 84C-HC. Spring Range Part Number 4" W.C. to 5" W.C. 740P005 PSIG to / PSIG 740P004 When the outlet pressure exceeds the OPSO set point, the pressure under the OPSO diaphragm (A) compresses the pressure spring (B) forcing the diaphragm stem (E) upwards and releasing plunger (D). This permits the shut-off spring (F) to force the shut-off disc (G) against the back side of the special double-ended orifice. E D C H A OPSO Diaphragm Plate B Pressure Spring C Cap D Plunger E Diaphragm Stem F Shut-off Spring G Shut-off Disc H Adjusting Screw B A F G Spring Range Description Basic regulator with full-capacity internal relief with /4" or " NPT vent. Basic regulator with full-capacity internal relief with /4" or " NPT vent. Basic regulator with full-capacity internal relief and overpressure shut-off and /4" or " NPT vent. Basic regulator with full-capacity internal relief and overpressure shut-off and /4" or " NPT vent. Basic regulator with full-capacity internal relief and overpressure, underpressure shut-off and /4" or " NPT vent. Basic regulator with full-capacity internal relief and overpressure, underpressure shut-off and /4" or " NPT vent. Universal Safety Shutoff Assembly (USSA) USSA protects the downstream piping from both over- and under-pressure conditions by shutting off the gas flow at the inlet side of the regulator orifice. Both Over- and under-pressure shut-off set points are adjustable depending on spring ranges selected. USSA Shutoff Spring Ranges Over Pressure Spring Ranges Part Number 7.5-4 W.C. 7P 0 - W.C. 7P4 4-44 W.C. 7P5 40-84 W.C. 7P6-5 PSIG 7P7 4-7 PSIG 7P8 Under Pressure Spring Ranges Spring Range Part Number - 6 W.C. 7P 6-4 W.C. 7P4 4-60 W.C. 7P5 Pressure Taps /8" NPT taps are available on most valve heads. Offset Valve Body
C and C-HC Series Service Regulators 0 Elster American Meter 9 4 5 4 5 0 6 8 Material Specifications Outlet Pressure 7 6 Diaphragm Case - Precision die-cast aluminum with an exclusive sevenstep advanced conversion coating, single-coat polyester primer and high solids polyurethane top coat. Valve Body - Cast grey iron, undercoated, single coat polyester primer and high solids polyurethane top coat. NPT threads meet ANSI/ ASME B.0.. BSP-TR threads meet BS EN 06. Available sizes: /4 x /4, /4 x, /4 x -/4, x, x -/4 and -/4 x -/4 NPT or BSP-TR Offset valve body: /4 x /4, /4 x and x NPT or BSP-TR Pressure Spring - Steel, zinc plated and yellow chromate. Color coded for identification. Color Code Part Number.5" to 6" W.C. Blue 7P04.5" to 7.5" W.C. Tan 7P089 5.5" to 8.5" W.C. Yellow 7P044 6" to " W.C. Brown 7P7 6" to 5" W.C. Purple 7P04 " to 8" W.C. White 7P060 4" to 48" W.C. Red 7P08 4" W.C. to PSIG Red - Red 7P049 4 Diaphragm Plate - Steel, Electrogalvanized. 5 Diaphragm - Buna N; Nylon fabric reinforced. 6 Seat Disc - Buna N; 60, 70 (std.) or 80 durometer rating. 7 Valve - High strength, corrosion resistant aluminum. Size Standard Part Number Part Number with OPSO 9/6" 7494P06 775P09 /" 7494P05 775P06 /8" 7494P0 775P04 5/6" 7494P0 775P0 /4" 7494P0 775P0 /6" 7494P00 775P0 /8" x /6" 7494P00 775P00 /8" 7494P09 N/A 8 Lever - Stamped aluminum. 9 Seal Plug - Polyester thermoplastic UV stabilized. 0 Plunger Valve/Plunger Guide - Minlon. Pressure Adjustment Screw - Minlon. Relief Valve Stem - Minlon. Vent Screen - Stainless Steel - All models are designed with a removable weather and bug-proof stainless steel screen to resist freezeups and to exclude foreign matter. The vent is threaded ¾ or NPT (BSP-TR threads available). Inside installation requires a vent line of sufficient diameter to carry gas vented by the regulator to a safe outside location away from any opening(s) in the structure. Comply with applicable Federal, State and local codes. 4 Vent Valve - Stainless Steel with Electrogalvanized steel retainer. 5 Relief Valve Spring - Steel, zinc plated and yellow chromate. Color coded for identification. Non-adjustable, standard set point of 8" w.c. above outlet set pressure of 7" w.c. Standard set point of. PSIG above outlet set pressure of PSIG. 6 Lever Pin - Carbon steel, zinc plated and yellow chromate.
C and C-HC Series Service Regulators 04 Elster American Meter C Series Regulator Capacity Performance /4" Outlet Set Point 7.0" W.C. (7.4 mbar) at 50 SCFH SCFH (m /h) 0.60 specific gravity gas at 60 F and 4.7 PSIA (0 C and.0 bar). Pressure spring 7P044. Outlet pressure variance not to exceed +" -" W.C. from set point, horizontal position. C Series Regulator Capacity SCFH (m /h) PSIG (bar) (0.07) (0.4) (0.) 5 (0.4) 0 (0.70) 5 (.00) 0 (.40) 0 (.0) 40 (.80) 60 (4.0) 00 (6.90) 5 (8.60) /8" x /6" 75 (7.8) 75 (0.6) (.7) (4.) (9.8) (.7) 00 (.) (48.) 00 /6" 75 (5.0) 00 (8.5) 75 (0.6) (4.) 750 (.) 950 (6.9) 00 (.) 400 (9.6) (48.) 00 (65.) /4" 50 (7.) 45 (.0) (4.) (9.8) 00 (.) 400 (9.6) (48.) 000 (56.6) 400 (68.0) 5/6" 5 (9.) 475 (.5) 600 (7.0) (.7) 00 (4.0) (4.5) (48.) 00 (6.) /8" 50 (5.6) (9.8) 950 (6.9) 400 (9.6) 600 (45.) 900 (5.8) 400 (68.0) /" 400 (.) (8.4) (.7) 000 (8.) (4.5) 900 (5.8) 00 (6.) 9/6" 400 (.) (8.4) (.7) 00 (4.0) (48.) 000 (56.6) 00 (65.) For optimum performance, maximum inlet pressure should not exceed maximum capacity rating for any given orifice size. " Outlet Set Point 7.0" W.C. (7.4 mbar) at 50 SCFH SCFH (m /h) 0.60 specific gravity gas at 60 F and 4.7 PSIA (0 C and.0 bar). Pressure spring 7P044. Outlet pressure variance not to exceed +" -" W.C. from set point, horizontal position. C Series Regulator Capacity SCFH (m /h) PSIG (bar) (0.07) (0.4) (0.) 5 (0.4) 0 (0.70) 5 (.00) 0 (.40) 0 (.0) 40 (.80) 60 (4.0) 00 (6.90) 5 (8.60) /8" x /6" 50 (7.) 50 45 (.0) (4.) 600 (7.0) 750 (.) 000 (8.) 600 (45.) 000 (56.6) /6" 75 (5.0) 50 (7.) 00 (8.5) (.7) (9.8) 900 (5.5) 00 (.) 400 (9.6) (48.) 400 (68.0) /4" 50 (7.) 50 (.7) (8.4) 000 (8.) 400 (9.6) (48.) 00 (65.) 5/6" 00 (8.5) (.7) (5.6) 750 (.) 400 (9.6) 900 (5.8) 00 (65.) /8" 75 (0.6) (4.) (9.8) 950 (6.9) 600 (45.) 00 /" 475 (.5) 600 (7.0) 850 (4.) 00 (4.0) 900 (5.8) 9/6" (4.) (8.4) 950 (6.9) 00 (6.8) 000 (56.6) For optimum performance, maximum inlet pressure should not exceed maximum capacity rating for any given orifice size.
C and C-HC Series Service Regulators 05 Elster American Meter C Series Regulator Capacity Performance -/4" Outlet Set Point 7.0" W.C. (7.4 mbar) at 50 SCFH SCFH (m /h) 0.60 specific gravity gas at 60 F and 4.7 PSIA (0 C and.0 bar). Pressure spring 7P044. Outlet pressure variance not to exceed +" -" W.C. from set point, horizontal position. C Series Regulator Capacity SCFH (m /h) PSIG (bar) (0.07) (0.4) (0.) 5 (0.4) 0 (0.70) 5 (.00) 0 (.40) 0 (.0) 40 (.80) 60 (4.0) 00 (6.90) /8" x /6" /6" 00 (5.7) 5 (9.) 45 (.0) 75 (7.8) 75 (0.6) (.7) (5.6) (9.8) (.7) 00 (.) 400 (9.6) (5.6) 850 (4.) 000 (8.) 00 (4.0) 600 (45.) /4" 5 (9.) (4.) (8.4) 000 (8.) (4.5) (5.0) 00 5/6" 50 600 (7.0) 950 (6.9) 600 (45.) 400 (68.0) /8" 75 (0.6) (9.8) 00 (4.0) 00 /" 475 (.5) 950 (6.9) (48.) 9/6" (4.) 400 (9.6) 900 (5.8) For optimum performance, maximum inlet pressure should not exceed maximum capacity rating for any given orifice size. /4" Outlet Set Point PSIG (0.4 bar) at 50 SCFH SCFH (m /h) 0.60 specific gravity gas at 60 F and 4.7 PSIA (0 C and.0 bar). Pressure spring 7P049. Outlet pressure variance not to exceed +/- 0% from set point, horizontal position. C Series Regulator Capacity SCFH (m /h) PSIG (bar) (0.) 5 (0.4) 0 (0.70) 5 (.00) 0 (.40) 0 (.0) 40 (.80) 60 (4.0) 00 (6.90) 5 (8.60) /8" x /6" 50 (4.) 50 (7.) 75 (0.6) (.7) (5.6) (9.8) 850 (4.) 00 (.) (48.) 00 /6" 75 (5.0) 5 (9.) (5.6) 750 (.) 900 (5.5) 00 (4.0) (4.5) 00 /4" 00 (8.5) (.7) (9.8) 900 (5.5) 00 (4.0) (4.5) 000 (56.6) 5/6" 5 (9.) 55 (4.9) 85 (.4) 00 (.) 00 (6.8) (5.0) 00 (6.) /8" 75 (0.6) 575 (6.) 000 (8.) 00 (6.8) 600 (45.) 00 /" 400 (.) (9.8) 00 (4.0) (4.5) 900 (5.8) 9/6" (4.) 750 (.) 00 (6.8) (5.0) For optimum performance, maximum inlet pressure should not exceed maximum capacity rating for any given orifice size.
C and C-HC Series Service Regulators 06 Elster American Meter C Series Regulator Capacity Performance " Outlet Set Point PSIG (0.4 bar) at 50 SCFH SCFH (m /h) 0.60 specific gravity gas at 60 F and 4.7 PSIA (0 C and.0 bar). Pressure spring 7P049. Outlet pressure variance not to exceed +/- 0% from set point, horizontal position. C Series Regulator Capacity SCFH (m /h) PSIG (bar) (0.) 5 (0.4) 0 (0.70) 5 (.00) 0 (.40) 0 (.0) 40 (.80) 60 (4.0) 00 (6.90) 5 (8.60) /8" x /6" 50 (4.) 5 (6.4) 50 45 (.0) (4.) (8.4) (.7) 00 (.) (48.) 00 /6" 5 (6.4) 50 600 (7.0) (.7) 000 (8.) 00 (6.8) (48.) /4" 50 (7.) (.7) 750 (.) 000 (8.) 00 (4.0) (48.) 00 (6.) 5/6" 50 (4.) 850 (4.) 00 (.) 400 (9.6) 000 (56.6) /8" 45 (.0) (8.4) 000 (8.) 400 (9.6) (5.0) /" (5.6) 750 (.) 00 (6.8) (48.) 00 9/6" (5.6) 900 (5.5) (4.5) 000 (56.6) For optimum performance, maximum inlet pressure should not exceed maximum capacity rating for any given orifice size. -/4" Outlet Set Point PSIG (0.4 bar) at 50 SCFH SCFH (m /h) 0.60 specific gravity gas at 60 F and 4.7 PSIA (0 C and.0 bar). Pressure spring 7P049. Outlet pressure variance not to exceed +/- 0% from set point, horizontal position. C Series Regulator Capacity SCFH (m /h) PSIG (bar) (0.) 5 (0.4) 0 (0.70) 5 (.00) 0 (.40) 0 (.0) 40 (.80) 60 (4.0) 00 (6.90) 5 (8.60) /8" x /6" 50 (4.) 5 (6.4) 50 45 (.0) (4.) (8.4) (.7) 00 (.) (48.) 00 /6" 5 (6.4) 50 600 (7.0) 850 (4.) 000 (8.) (4.5) 900 (5.8) /4" 50 (4.) 850 (4.) 00 (4.0) (48.) 5/6" 75 (0.6) 600 (7.0) 00 (.) 600 (45.) 00 (6.) /8" 45 (.0) (9.8) 00 (4.0) 900 (5.8) /" (5.6) 900 (5.5) (48.) 9/6" (5.6) 00 (.) 00 (6.) For optimum performance, maximum inlet pressure should not exceed maximum capacity rating for any given orifice size.
C and C-HC Series Service Regulators Technical Bulletin
C and C-HC Series Service Regulators 0 Elster American Meter The C Series pressure regulators are designed to control natural gas, air, nitrogen, carbon dioxide, propane vapor, and other non-corrosive gases in residential, light commercial, and small industrial applications. General Information Outlet pressures between.5" W.C. and PSIG are available. Operating temperature range is -0 F to 50 F (-0 C to 65 C). Maximum flow rate is SCFH (70.8 m /h). All models conform to ANSI Code B09.4-998, and CGA Service-Type Regulator Specification CAN/CGA-6.8-M95. Features Variety of interchangeable orifices and spring ranges 90 Degree (Right Angle), 80 Degree (Straight-Flow), or Offset Valve Body (See photo below) Wide range of valve body connection sizes Options Vent Elbow The regulator vent opening should face downward (6 o'clock) to minimize the chance of blockage from ice and snow. If not possible, a /4" NPT plastic, 90 vent elbow (part number 7804P05) and separate protective screen (part number 70400P07) may be screwed into the vent to provide the necessary protection. Elevation Compensation The E.C. orifice is recommended for installations where the inlet pressure may vary over a wide range. The E.C. orifice is available in two sizes: /8" x /6" and /6". The capacities of these orifices are the same as the standard orifice of the same size. Full Capacity Relief Valve Full capacity internal relief valve standard on all models. (See Performance Graphs on page 9) Splashguards UV stabilized, weather-resistant, resin device that protects the vent screen from Applications Model Number 8C 8C-HC 84C 84C-HC 85C w/ USSA 85C-HC w/ USSA splashes while providing a large external vent opening to keep regulators working properly. Safety Shutoff Devices Overpressure Shutoff (OPSO) Operates independently. The OPSO will shut off the gas supply in the event of a serious downstream pressure build-up. These are available in two pressure ranges on the Models 84C and 84C-HC. Spring Range Part Number 4" W.C. to 5" W.C. 740P005 PSIG to / PSIG 740P004 When the outlet pressure exceeds the OPSO set point, the pressure under the OPSO diaphragm (A) compresses the pressure spring (B) forcing the diaphragm stem (E) upwards and releasing plunger (D). This permits the shut-off spring (F) to force the shut-off disc (G) against the back side of the special double-ended orifice. E D C H A OPSO Diaphragm Plate B Pressure Spring C Cap D Plunger E Diaphragm Stem F Shut-off Spring G Shut-off Disc H Adjusting Screw B A F G Spring Range Description Basic regulator with full-capacity internal relief with /4" or " NPT vent. Basic regulator with full-capacity internal relief with /4" or " NPT vent. Basic regulator with full-capacity internal relief and overpressure shut-off and /4" or " NPT vent. Basic regulator with full-capacity internal relief and overpressure shut-off and /4" or " NPT vent. Basic regulator with full-capacity internal relief and overpressure, underpressure shut-off and /4" or " NPT vent. Basic regulator with full-capacity internal relief and overpressure, underpressure shut-off and /4" or " NPT vent. Universal Safety Shutoff Assembly (USSA) USSA protects the downstream piping from both over- and under-pressure conditions by shutting off the gas flow at the inlet side of the regulator orifice. Both Over- and under-pressure shut-off set points are adjustable depending on spring ranges selected. USSA Shutoff Spring Ranges Over Pressure Spring Ranges Part Number 7.5-4 W.C. 7P 0 - W.C. 7P4 4-44 W.C. 7P5 40-84 W.C. 7P6-5 PSIG 7P7 4-7 PSIG 7P8 Under Pressure Spring Ranges Spring Range Part Number - 6 W.C. 7P 6-4 W.C. 7P4 4-60 W.C. 7P5 Pressure Taps /8" NPT taps are available on most valve heads. Offset Valve Body
C and C-HC Series Service Regulators 0 Elster American Meter 9 4 5 4 5 0 6 8 Material Specifications Outlet Pressure 7 6 Diaphragm Case - Precision die-cast aluminum with an exclusive sevenstep advanced conversion coating, single-coat polyester primer and high solids polyurethane top coat. Valve Body - Cast grey iron, undercoated, single coat polyester primer and high solids polyurethane top coat. NPT threads meet ANSI/ ASME B.0.. BSP-TR threads meet BS EN 06. Available sizes: /4 x /4, /4 x, /4 x -/4, x, x -/4 and -/4 x -/4 NPT or BSP-TR Offset valve body: /4 x /4, /4 x and x NPT or BSP-TR Pressure Spring - Steel, zinc plated and yellow chromate. Color coded for identification. Color Code Part Number.5" to 6" W.C. Blue 7P04.5" to 7.5" W.C. Tan 7P089 5.5" to 8.5" W.C. Yellow 7P044 6" to " W.C. Brown 7P7 6" to 5" W.C. Purple 7P04 " to 8" W.C. White 7P060 4" to 48" W.C. Red 7P08 4" W.C. to PSIG Red - Red 7P049 4 Diaphragm Plate - Steel, Electrogalvanized. 5 Diaphragm - Buna N; Nylon fabric reinforced. 6 Seat Disc - Buna N; 60, 70 (std.) or 80 durometer rating. 7 Valve - High strength, corrosion resistant aluminum. Size Standard Part Number Part Number with OPSO 9/6" 7494P06 775P09 /" 7494P05 775P06 /8" 7494P0 775P04 5/6" 7494P0 775P0 /4" 7494P0 775P0 /6" 7494P00 775P0 /8" x /6" 7494P00 775P00 /8" 7494P09 N/A 8 Lever - Stamped aluminum. 9 Seal Plug - Polyester thermoplastic UV stabilized. 0 Plunger Valve/Plunger Guide - Minlon. Pressure Adjustment Screw - Minlon. Relief Valve Stem - Minlon. Vent Screen - Stainless Steel - All models are designed with a removable weather and bug-proof stainless steel screen to resist freezeups and to exclude foreign matter. The vent is threaded ¾ or NPT (BSP-TR threads available). Inside installation requires a vent line of sufficient diameter to carry gas vented by the regulator to a safe outside location away from any opening(s) in the structure. Comply with applicable Federal, State and local codes. 4 Vent Valve - Stainless Steel with Electrogalvanized steel retainer. 5 Relief Valve Spring - Steel, zinc plated and yellow chromate. Color coded for identification. Non-adjustable, standard set point of 8" w.c. above outlet set pressure of 7" w.c. Standard set point of. PSIG above outlet set pressure of PSIG. 6 Lever Pin - Carbon steel, zinc plated and yellow chromate.
C and C-HC Series Service Regulators 04 Elster American Meter C Series Regulator Capacity Performance /4" Outlet Set Point 7.0" W.C. (7.4 mbar) at 50 SCFH SCFH (m /h) 0.60 specific gravity gas at 60 F and 4.7 PSIA (0 C and.0 bar). Pressure spring 7P044. Outlet pressure variance not to exceed +" -" W.C. from set point, horizontal position. C Series Regulator Capacity SCFH (m /h) PSIG (bar) (0.07) (0.4) (0.) 5 (0.4) 0 (0.70) 5 (.00) 0 (.40) 0 (.0) 40 (.80) 60 (4.0) 00 (6.90) 5 (8.60) /8" x /6" 75 (7.8) 75 (0.6) (.7) (4.) (9.8) (.7) 00 (.) (48.) 00 /6" 75 (5.0) 00 (8.5) 75 (0.6) (4.) 750 (.) 950 (6.9) 00 (.) 400 (9.6) (48.) 00 (65.) /4" 50 (7.) 45 (.0) (4.) (9.8) 00 (.) 400 (9.6) (48.) 000 (56.6) 400 (68.0) 5/6" 5 (9.) 475 (.5) 600 (7.0) (.7) 00 (4.0) (4.5) (48.) 00 (6.) /8" 50 (5.6) (9.8) 950 (6.9) 400 (9.6) 600 (45.) 900 (5.8) 400 (68.0) /" 400 (.) (8.4) (.7) 000 (8.) (4.5) 900 (5.8) 00 (6.) 9/6" 400 (.) (8.4) (.7) 00 (4.0) (48.) 000 (56.6) 00 (65.) For optimum performance, maximum inlet pressure should not exceed maximum capacity rating for any given orifice size. " Outlet Set Point 7.0" W.C. (7.4 mbar) at 50 SCFH SCFH (m /h) 0.60 specific gravity gas at 60 F and 4.7 PSIA (0 C and.0 bar). Pressure spring 7P044. Outlet pressure variance not to exceed +" -" W.C. from set point, horizontal position. C Series Regulator Capacity SCFH (m /h) PSIG (bar) (0.07) (0.4) (0.) 5 (0.4) 0 (0.70) 5 (.00) 0 (.40) 0 (.0) 40 (.80) 60 (4.0) 00 (6.90) 5 (8.60) /8" x /6" 50 (7.) 50 45 (.0) (4.) 600 (7.0) 750 (.) 000 (8.) 600 (45.) 000 (56.6) /6" 75 (5.0) 50 (7.) 00 (8.5) (.7) (9.8) 900 (5.5) 00 (.) 400 (9.6) (48.) 400 (68.0) /4" 50 (7.) 50 (.7) (8.4) 000 (8.) 400 (9.6) (48.) 00 (65.) 5/6" 00 (8.5) (.7) (5.6) 750 (.) 400 (9.6) 900 (5.8) 00 (65.) /8" 75 (0.6) (4.) (9.8) 950 (6.9) 600 (45.) 00 /" 475 (.5) 600 (7.0) 850 (4.) 00 (4.0) 900 (5.8) 9/6" (4.) (8.4) 950 (6.9) 00 (6.8) 000 (56.6) For optimum performance, maximum inlet pressure should not exceed maximum capacity rating for any given orifice size.
C and C-HC Series Service Regulators 05 Elster American Meter C Series Regulator Capacity Performance -/4" Outlet Set Point 7.0" W.C. (7.4 mbar) at 50 SCFH SCFH (m /h) 0.60 specific gravity gas at 60 F and 4.7 PSIA (0 C and.0 bar). Pressure spring 7P044. Outlet pressure variance not to exceed +" -" W.C. from set point, horizontal position. C Series Regulator Capacity SCFH (m /h) PSIG (bar) (0.07) (0.4) (0.) 5 (0.4) 0 (0.70) 5 (.00) 0 (.40) 0 (.0) 40 (.80) 60 (4.0) 00 (6.90) /8" x /6" /6" 00 (5.7) 5 (9.) 45 (.0) 75 (7.8) 75 (0.6) (.7) (5.6) (9.8) (.7) 00 (.) 400 (9.6) (5.6) 850 (4.) 000 (8.) 00 (4.0) 600 (45.) /4" 5 (9.) (4.) (8.4) 000 (8.) (4.5) (5.0) 00 5/6" 50 600 (7.0) 950 (6.9) 600 (45.) 400 (68.0) /8" 75 (0.6) (9.8) 00 (4.0) 00 /" 475 (.5) 950 (6.9) (48.) 9/6" (4.) 400 (9.6) 900 (5.8) For optimum performance, maximum inlet pressure should not exceed maximum capacity rating for any given orifice size. /4" Outlet Set Point PSIG (0.4 bar) at 50 SCFH SCFH (m /h) 0.60 specific gravity gas at 60 F and 4.7 PSIA (0 C and.0 bar). Pressure spring 7P049. Outlet pressure variance not to exceed +/- 0% from set point, horizontal position. C Series Regulator Capacity SCFH (m /h) PSIG (bar) (0.) 5 (0.4) 0 (0.70) 5 (.00) 0 (.40) 0 (.0) 40 (.80) 60 (4.0) 00 (6.90) 5 (8.60) /8" x /6" 50 (4.) 50 (7.) 75 (0.6) (.7) (5.6) (9.8) 850 (4.) 00 (.) (48.) 00 /6" 75 (5.0) 5 (9.) (5.6) 750 (.) 900 (5.5) 00 (4.0) (4.5) 00 /4" 00 (8.5) (.7) (9.8) 900 (5.5) 00 (4.0) (4.5) 000 (56.6) 5/6" 5 (9.) 55 (4.9) 85 (.4) 00 (.) 00 (6.8) (5.0) 00 (6.) /8" 75 (0.6) 575 (6.) 000 (8.) 00 (6.8) 600 (45.) 00 /" 400 (.) (9.8) 00 (4.0) (4.5) 900 (5.8) 9/6" (4.) 750 (.) 00 (6.8) (5.0) For optimum performance, maximum inlet pressure should not exceed maximum capacity rating for any given orifice size.
C and C-HC Series Service Regulators 06 Elster American Meter C Series Regulator Capacity Performance " Outlet Set Point PSIG (0.4 bar) at 50 SCFH SCFH (m /h) 0.60 specific gravity gas at 60 F and 4.7 PSIA (0 C and.0 bar). Pressure spring 7P049. Outlet pressure variance not to exceed +/- 0% from set point, horizontal position. C Series Regulator Capacity SCFH (m /h) PSIG (bar) (0.) 5 (0.4) 0 (0.70) 5 (.00) 0 (.40) 0 (.0) 40 (.80) 60 (4.0) 00 (6.90) 5 (8.60) /8" x /6" 50 (4.) 5 (6.4) 50 45 (.0) (4.) (8.4) (.7) 00 (.) (48.) 00 /6" 5 (6.4) 50 600 (7.0) (.7) 000 (8.) 00 (6.8) (48.) /4" 50 (7.) (.7) 750 (.) 000 (8.) 00 (4.0) (48.) 00 (6.) 5/6" 50 (4.) 850 (4.) 00 (.) 400 (9.6) 000 (56.6) /8" 45 (.0) (8.4) 000 (8.) 400 (9.6) (5.0) /" (5.6) 750 (.) 00 (6.8) (48.) 00 9/6" (5.6) 900 (5.5) (4.5) 000 (56.6) For optimum performance, maximum inlet pressure should not exceed maximum capacity rating for any given orifice size. -/4" Outlet Set Point PSIG (0.4 bar) at 50 SCFH SCFH (m /h) 0.60 specific gravity gas at 60 F and 4.7 PSIA (0 C and.0 bar). Pressure spring 7P049. Outlet pressure variance not to exceed +/- 0% from set point, horizontal position. C Series Regulator Capacity SCFH (m /h) PSIG (bar) (0.) 5 (0.4) 0 (0.70) 5 (.00) 0 (.40) 0 (.0) 40 (.80) 60 (4.0) 00 (6.90) 5 (8.60) /8" x /6" 50 (4.) 5 (6.4) 50 45 (.0) (4.) (8.4) (.7) 00 (.) (48.) 00 /6" 5 (6.4) 50 600 (7.0) 850 (4.) 000 (8.) (4.5) 900 (5.8) /4" 50 (4.) 850 (4.) 00 (4.0) (48.) 5/6" 75 (0.6) 600 (7.0) 00 (.) 600 (45.) 00 (6.) /8" 45 (.0) (9.8) 00 (4.0) 900 (5.8) /" (5.6) 900 (5.5) (48.) 9/6" (5.6) 00 (.) 00 (6.) For optimum performance, maximum inlet pressure should not exceed maximum capacity rating for any given orifice size.
SERIES B: 5M75 ROOTS Meter UNITS Imperial UNITS Metric Temperature Range deg. F -40 to +40 deg. C -40 to +60 Base Rating (Q Max.) acfh 0 m /h 4,5 Max. Operating Pressure (MAOP) psig 75 kpa 00 Leak Test (5% MAOP) psig 9 kpa 50 Static Test ( x MAOP) psig 50 kpa 400 Rangeability +/- % ratio 0: ratio 0: Rangeability +/- % ratio 5: ratio 5: Start Rate cfh. m /h 0,040 Stop Rate cfh 0.8 m /h 0,07 Flow Rate @ 0.5 w.c., Gas cfh 975 m /h,6 Avg. Differential, 00% Flow in. w.c.. mbar,6 Max. Pressurization Rate psig/sec 5 kpa/sec 5 Max. Operating Speed rpm 50 rpm 50 Gear Ratio ratio 70: ratio 95,5: Displaced Volume/Revolution cf 0.0707 m 0,000049 Drive Rate, CD cf/rev 0 m /rev Drive Rate,TD cf/rev 00 m /rev 0 Temp. Compensating Range (TC,TD) deg. F -0 to +0 deg. C -9 to +49 Min. Odometer Reading cf 0. m 0.00 Odometer Turnover yrs..8 yrs. 8,06 Nominal Pipe Size in. mm 80 Flange-to-Flange in. 6-/4 mm 7 Flange Connection ANSI 5#FF ANSI 5#FF Bolts per Flange qty. 4 qty. 4 Bolt Size in. 5/8 - in. 5/8 - Flange Bolt Hole Depth in. 5/6 mm,8 Bolt Torque: Lubricated/Non-Lub. ft.-lb. 55/60 N-m 74/8 Restricting (0%) in. / mm 8,56 Oil Capacity Side oz..5 ml 7 Oil Capacity Top oz. 7.65 ml 6 Counter Version (CTR) Net Weight lbs. 5 kg 5,9 Shipping Weight lbs. 8 kg 7, Carton Size in. 7 x x 9 cm 69 x 8 x Counter with Instrument Drive (CD) Net Weight lbs. 8 kg 7, Shipping Weight lbs. 4 kg 8,6 Carton Size in. x 5 x cm 79 x 8 x NOTES: Bolt Length varies by application. Weights and dimensions available for CPS,TC,TD,TPS upon request.
Accuracy Curve RATE - % of Meter Rating 0 0 0 0 40 50 60 70 80 90 00 0 0 ACCURACY - % 00 99 98 97 Model 5M75 Body Type Series B Start Rate. cfh Stop Rate 0.8 cfh Rangeability ±% 0: Rangeability ±% 5: Above data has been determined from tests performed with air at atmospheric pressure and ambient temperature, using positive displacement bell or piston provers dimensionally traceable to the United States National Institute of Standards and Technology (NIST) and traceable to NMi- Netherlands Measurements Accuracy Institute Curve for volumetric flow rate..0 Differential Curve DIFFERENTIAL - IN. W.C..5.0 0.5 0.0 0 0 0 0 40 50 60 70 80 90 00 RATE - % of Meter Rating Centerline to 5M75 Overall Length Overall Height Width (Flange/Flange) Accessory End (CL-AU) Request Detailed Series B inches mm inches mm inches mm inches mm Drawing Number CTR / TC 0 508 6-/ 77 6-/4 7-5/6 D05457-000 CD / TD -7/ 606 6-/ 77 6-/4 7 6-5/ 4 D0544-000 CPS / TPS -/8 56 6-/ 77 6-/4 7 4-7/6 68 D054670-000 IMC/C -/ 597 6-/ 77 6-/4 7 5-/6 40 D056486-000 IMC/W 4-/ 6 6-/ 77 6-/4 7 6-/6 47 D05670-000 Accessory Unit CL-AU Length Height To order Specify: Meter Series, Size and Type (i.e., ROOTS Meter Series B 5M75 CD). For CD or TD, specify (Top or Side) and ID Rotation (CW-B or CCW-A). For Pulser, specify Single or Dual Connectors and Connector Type (MS Circular, Conduit or Cable Gland). For more specific ordering information on the electronic products, request: TS:SSP, TS:IMC/C or S:IMC/W. Contact the factory for other available information, options, or special requests. Dresser Roots Meters & Instruments P. O. Box 476 Houston, TX USA 774-76 website: www.dresser.com Dresser, Inc. Inside US Ph:.5.4 Fax:.5.54 Outside US Ph: 8.966.400 Fax: 8.966.408 www.rootsmeters.com 00 Dresser, Inc. ROOTS is a registered trademark of Dresser, Inc. DS:5M75.0
Roots Meters & Instruments ROOTS Meter Series B Featuring Series Accessory Units Series B version ROOTS meters are designed to provide accurate gas measurement over a wide range of flow, pressure and temperature conditions. Available Types Include: CTR Non-Compensated Counter CD Non-Compensated Counter with Instrument Drive TC Temperature Compensated Counter TD Temperature Compensated Counter with Instrument Drive CTR or TC with Solid State Pulser Low Frequency pulse output CTR or TC with AMR Adapter ICEX Counter (CTR) with High Frequency Electronic Transmitter Series B meter bodies are also available with the integral electronic ROOTS IMC/W volume, pressure and temperature corrector, or the ROOTS IMC/W-T for a temperature only corrected reading.
Full Range of Sizes: meter sizes offer a competitive range of rotary meters for commercial and industrial metering applications. Allow for the selection of the correct meter size for cost effectiveness and accurate measurement. Standardized Flanges: Sizes 8C through M have a 6-/4 (7mm) flange-to-flange dimension and ANSI 50 flanges for standardization in the meter set design. As loads change, meter sizes are easily interchanged, saving the cost of re-piping. Accurate Low Flow Performance: Low start/stop rates extend the rangeability (gas measured) over a wider range of flow conditions. Low Pressure Differentials: Reducing the maximum operating speed provides lower pressure differentials for low pressure applications, as well as extending the meter s life-expectancy. SERIES ACCESSORY UNITS Oil-free Design: Series accessories feature high quality and long-term reliability with an oil-free permanently lubricated design. Oil is not required for the Polymer bushings and pre-lubricated, shielded ball bearings. Permanent lubrication equates to easier installation and less maintenance. Durable, Weather Resistant Cover: Optical Quality Lexan covers on Series accessories offer exceptional Ultraviolet protection while the cylindrical design allows the unit to easily shed rain, snow, ice and dirt. The single piece cover design provides added protection against leakage under extreme conditions. High and Low Frequency Pulser Options: The Counter with Electronic Transmitter (ICEX) provides a high frequency non-compensated pulse output for applications requiring information on the gas flow rate while the low frequency solid state pulsers are a lower cost option for both non-compensated (ICPWX) and temperature compensated (ITPWX) volume accumulation applications. Non-Moving Odometer Masking System: A unique and versatile odometer masking design using opaque or semi-transparent covers offers configurable, trouble-free masking. Universal Instrument Drive (ID) Assembly: One size fits all with the Series Instrument Drive Assembly. Inventory costs are reduced by stocking one ID Assembly. AMR Adapter: The new direct drive AMR Adapter offers you a low cost solution for Series B CTR or TC meters in applications that require the adaptation of a Residential ERT or Cellnet AMR. The AMR Adapter is available as a conversion kit for field installation or factory installed on new meters.
General Information The Series B ROOTS meter is a positive displacement, rotary type gas meter designed for continuously measuring and indicating the accurate measurement of gas. ROOTS meters are suitable for handling most types of clean, dry, common gases at either constant or varying flow rates. Meters of standard construction are not directly suitable for handling acetylene, biogas or sewage gas. Contact the factory for information on specially constructed meters made of materials more compatible with these and other gases. Volumetric accuracy of the ROOTS meter is permanent, non-adjustable, and is not affected by low or varying line pressure. Series B meters may be used satisfactorily for pressures ranging from a few ounces to full Maximum Allowable Operating Pressure (MAOP). Displaced volume measurement is completely independent of the gas specific gravity, temperature, and pressure. Series B ROOTS meters have a MAOP rating of 75 psig (00kPa). Every meter is static pressure tested at the factory at twice its MAOP and leak tested at 5 percent of MAOP in accordance with ASME Boiler Pressure Vessel Codes. Other pressure ratings are available. Consult Factory. ROOTS meters are manufactured in accordance with ANSI B09. for Rotary Type Gas Displacement Meters. Series B ROOTS meter sizes 8C through 56M, have flanged inlet and outlet connections conforming dimensionally with ANSI/ASME standards. Sizes 8C through M are available with -/ NPT connections, upon special request. The meter operating temperature range is from -40 F to +40 F (-40 C to +60 C) while the temperature compensating mechanism of the TC accessory provides a corrected reading for temperatures ranging from -0 F to +0 F (-9 C to +49 C). Series B ROOTS meter bodies accept a wide range of Series accessories for all metering applications. AMR Adapters for Series B ROOTS Meter. AMR Adapter and ERT installed on a ROOTS Meter (top inlet meter installation shown)
Meter Specifications SERIES B Units 8C75 C75 5C75 M75 M75 5M75 7M75 M75 6M75 M75 M 8M75 56M75 Base Rating acfh 00 000 000 0 0 000 6000 000 000 0 56000 Max. Operating Pressure psig 75* 75* 75* 75 75 75 75 75 75 75 75 75 Rangeability +/-% ratio 6: : 40: 68: 76: 0: 67: 4: 6: 40: 69: 90: 5: Rangeability +/-% ratio 46: 58: 78: 6: 9: 5: 5: 7: : 60: 78: 0: 09: Start Rate acfh.79.0.94.9.. 5..9. 0. 7 40 Stop Rate acfh.0.74.57..8 0.8.4..9 8 5.75 0 9 Flow Rate, 0.5 w.c.,gas acfh 00 000 580 975 5400 9950 4 0948 0600 000 Differential, 00% Flow in.w.c. 0.45 0.6 0.75 0.65...6.06...08.9. Drive Rate, CD/TD cf/rev 0/00 0/00 0/00 0/00 0/00 0/00 0/00 0/00 00/000 00/NA 00/NA 00/NA 00/NA Min. CTR Reading cf 0. 0. 0. 0. 0. 0. 0. 0. Nominal Pipe Size in. 4 4 6 4 6 8 Flange/Flange Dim. in. 6-/4 6-/4 6-/4 6-/4 6-/4 6-/4 9-/ 9-/ 9-/ 6 9-/ 8 Oil Capacity: Side oz. 0.8 0.8 0.8... 40.4 40 40 Oil Capacity: Top oz. 7.6 7.6 7.6.9.9.9 54.8 54 54 Meter Sizing Model 8C75* C75* 5C75* M75* M75* 5M75* 7M75 M75 6M75 M75 M 8M75 56M75 Base Rating (acfh) 00 000 000 0 0 000 6000 000 000 0 56000 Meter Pressure (psig) Corrected Capacity at Metering Pressure - MSCFH 0.84..6.. 5. 7..5 6.7 4 4 9.7 58.5 5..5.6 4 6.6 9. 4.5. 0. 0. 50 7.8 5..9 4 5.4 8.4 8.7 9.4 4.8 6.5 6.5 0.7 49.8 60 4 5.6 7.6 0. 5. 5. 5.4 55.6 80.8 6. 6. 9.9 8.9 00 6. 8.5.7 5.5. 8.8 54.4 85.4 4. 78.6 78.6 95. 44.9 50 8.9. 7. 56 78 79 56.7 56.7 44. 65 75 0. 4. 9. 5.7 9 64 90 4 06 95.7 95.7 488.6 7.5 00.7 6.9 9. 4.7 7.8 4.8 84.7 *Available with 00 psig Rating. To select proper meter size, use Minimum Operating Pressure and Maximum Instantaneous Hourly Flow Rate. Complete Data Sheets are available for each meter size. Request Data Sheet by meter model. Roots Meters & Instruments Dresser, Inc. 640 Port Northwest Drive Houston, Texas 7704-645 USA Inside US Ph:.5.4 Fax:.5.54 Outside US Ph: 8.590.0 Fax: 8.590.494 009 Dresser, Inc. Roots, and Dresser are registered trademarks of Dresser, Inc. www.dresser.com TS:B 8.09
RotaRead Pulser Fits Roots Rotary B Style Meters Standard Conduit Connection /" NPT Output Connection for Conduit Standard Pulses/revolution RotaRead Model RMLL-CU-CF RotaRead (Dual Pulse Output) Installed on B TC Index Meter Type Roots Models 8C M Roots Models 6M 56M Resolution Available Single Pulse Output: Un-corrected: 5 cu ft/pulse pulses/revolution Temp.Corrected: 50 cu ft/pulse pulses/revolution Dual Pulse Output: Un-corrected and Corrected Single Pulse Output: Un-corrected: 50 cu ft/pulse pulses/revolution Temp.Corrected: 50 cu ft/pulse pulses/revolution Not available on M - 56M Temperature: Operational from -40 to +40 F Moisture: Operational to 00% humidity: Case is plated to protect from corrosion; all electronics are potted. Maximum switching voltage D.C.: 00 volts Maximum switching current D.C.:.5 amps Maximum switching watts D.C.: 0 watts Minimum voltage breakdown D.C.: 0 volts Contact resistance: 0. ohms Open circuit resistance: > 00,000,000 ohms Maximum rate contact closure:. pulses/sec Maximum bounce time: 0. ms max. Dual Pulse Output: Un-corrected and Corrected Resistance:00 ohms standard electric throughput resistance for interference suppression. Custom series and parallel values available. De-Bounce: RIO Tronics recommends a sec. debounce at host recorder's front end input for all RotaRead products. Patent# 4008458. Additional patents pending. RIOTronics Corp. reserves the right to modify features and specifications without notice. Wire Tamper Detection: RIOTronics provides various end of the line circuitry at the Form A switch to enable detection of breaks or shorts - please contact the company for custom solutions California 55 Arden Rd., Hayward, CA 94545 Tel: 50-5-9040 Fax: 50-5-07-446-88 Washington P.O. Box 98, Issaquah, WA 9807 Tel: 45-9-460 Fax: 45-557-084-58-8
SERIES B: M75 ROOTS Meter UNITS Imperial UNITS Metric Temperature Range deg. F -40 to +40 deg. C -40 to +60 Base Rating (Q Max.) acfh 000 m /h 56,6 Max. Operating Pressure (MAOP) psig 75 kpa 00 Leak Test (5% MAOP) psig 9 kpa 50 Static Test ( x MAOP) psig 50 kpa 400 Rangeability +/- % ratio 68: ratio 68: Rangeability +/- % ratio 6: ratio 6: Start Rate cfh.9 m /h 0,058 Stop Rate cfh. m /h 0,0 Flow Rate @ 0.5 w.c., Gas cfh 000 m /h 56,6 Avg. Differential, 00% Flow in. w.c. 0.65 mbar,6 Max. Pressurization Rate psig/sec 5 kpa/sec 5 Max. Operating Speed rpm 667 rpm 667 Gear Ratio ratio : ratio 76,4705: Displaced Volume/Revolution cf 0.0 m 0,000566 Drive Rate, CD cf/rev 0 m /rev 0, Drive Rate,TD cf/rev 00 m /rev Temp. Compensating Range (TC,TD) deg. F -0 to +0 deg. C -9 to +49 Min. Odometer Reading cf 0. m 0,00 Odometer Turnover yrs. 5.7 yrs.,0 Nominal Pipe Size in. mm 50,8 Flange-to-Flange in. 6-/4 mm 7 Flange Connection ANSI 5#FF ANSI 5#FF Bolts per Flange qty. 4 qty. 4 Bolt Size in. 5/8 - in. 5/8 - Flange Bolt Hole Depth in. 5/6 mm,8 Bolt Torque: Lubricated/Non-Lub. ft.-lb. 55/60 N-m 74/8 Restricting (0%) in. 7/6 mm, Oil Capacity Side oz..5 ml 7 Oil Capacity Top oz. 7.65 ml 6 Counter Version (CTR) Net Weight lbs. 6 kg,8 Shipping Weight lbs. 8 kg,7 Carton Size in. 7 x x 9 cm 69 x 8 x Counter with Instrument Drive (CD) Net Weight lbs. 0 kg,6 Shipping Weight lbs. kg 4,5 Carton Size in. x 5 x cm 79 x 8 x NOTES: Bolt Length varies by application. Weights and dimensions available for CPS,TC,TD,TPS upon request.
Accuracy Curve RATE - % of Meter Rating 0 0 0 0 40 50 60 70 80 90 00 0 0 ACCURACY - % 00 99 98 97 Model M75 Body Type Series B Start Rate.9 cfh Stop Rate. cfh Rangeability ±% 68: Rangeability ±% 6: Above data has been determined from tests performed with air at atmospheric pressure and ambient temperature, using positive displacement bell or piston provers dimensionally traceable to the United States National Institute of Standards and Technology (NIST) and traceable to NMi - Netherlands Measurements Accuracy Curve Institute for volumetric flow rate..0 Differential Curve DIFFERENTIAL - IN. W.C..5.0 0.5 0.0 0 0 0 0 40 50 60 70 80 90 00 RATE - % of Meter Rating Centerline to M75 Overall Length Overall Height Width (Flange/Flange) Accessory End (CL-AU) Request Detailed Series B inches mm inches mm inches mm inches mm Drawing Number CTR / TC 5-9/ 404 6-/ 77 6-/4 7 0-/4 60 D05457-000 CD / TD 9-5/ 50 6-/ 77 6-/4 7 4-/8 59 D0544-000 CPS / TPS 8-/ 458 6-/ 77 6-/4 7 -/8 4 D054670-000 IMC/C 9-/ 49 6-/ 77 6-/4 7 -/4 49 D056486-000 IMC/W 0-/ 58 6-/ 77 6-/4 7 4-/4 75 D05670-000 Accessory Unit CL-AU Length Height To order Specify: Meter Series, Size and Type (i.e., ROOTS Meter Series B M75 CD). For CD or TD, specify (Top or Side) and ID Rotation (CW-B or CCW-A). For Pulser, specify Single or Dual Connectors and Connector Type (MS Circular, Conduit or Cable Gland). For more specific ordering information on the electronic products, request: TS:SSP, TS:IMC/C or S:IMC/W. Contact the factory for other available information, options, or special requests. Dresser Roots Meters & Instruments P. O. Box 476 Houston, TX USA 774-76 website: www.dresser.com Dresser, Inc. Inside US Ph:.5.4 Fax:.5.54 Outside US Ph: 8.966.400 Fax: 8.966.408 www.rootsmeters.com 00 Dresser, Inc. ROOTS is a registered trademark of Dresser, Inc. DS:M75.0
Roots Meters & Instruments ROOTS Meter Series B Featuring Series Accessory Units Series B version ROOTS meters are designed to provide accurate gas measurement over a wide range of flow, pressure and temperature conditions. Available Types Include: CTR Non-Compensated Counter CD Non-Compensated Counter with Instrument Drive TC Temperature Compensated Counter TD Temperature Compensated Counter with Instrument Drive CTR or TC with Solid State Pulser Low Frequency pulse output CTR or TC with AMR Adapter ICEX Counter (CTR) with High Frequency Electronic Transmitter Series B meter bodies are also available with the integral electronic ROOTS IMC/W volume, pressure and temperature corrector, or the ROOTS IMC/W-T for a temperature only corrected reading.
Full Range of Sizes: meter sizes offer a competitive range of rotary meters for commercial and industrial metering applications. Allow for the selection of the correct meter size for cost effectiveness and accurate measurement. Standardized Flanges: Sizes 8C through M have a 6-/4 (7mm) flange-to-flange dimension and ANSI 50 flanges for standardization in the meter set design. As loads change, meter sizes are easily interchanged, saving the cost of re-piping. Accurate Low Flow Performance: Low start/stop rates extend the rangeability (gas measured) over a wider range of flow conditions. Low Pressure Differentials: Reducing the maximum operating speed provides lower pressure differentials for low pressure applications, as well as extending the meter s life-expectancy. SERIES ACCESSORY UNITS Oil-free Design: Series accessories feature high quality and long-term reliability with an oil-free permanently lubricated design. Oil is not required for the Polymer bushings and pre-lubricated, shielded ball bearings. Permanent lubrication equates to easier installation and less maintenance. Durable, Weather Resistant Cover: Optical Quality Lexan covers on Series accessories offer exceptional Ultraviolet protection while the cylindrical design allows the unit to easily shed rain, snow, ice and dirt. The single piece cover design provides added protection against leakage under extreme conditions. High and Low Frequency Pulser Options: The Counter with Electronic Transmitter (ICEX) provides a high frequency non-compensated pulse output for applications requiring information on the gas flow rate while the low frequency solid state pulsers are a lower cost option for both non-compensated (ICPWX) and temperature compensated (ITPWX) volume accumulation applications. Non-Moving Odometer Masking System: A unique and versatile odometer masking design using opaque or semi-transparent covers offers configurable, trouble-free masking. Universal Instrument Drive (ID) Assembly: One size fits all with the Series Instrument Drive Assembly. Inventory costs are reduced by stocking one ID Assembly. AMR Adapter: The new direct drive AMR Adapter offers you a low cost solution for Series B CTR or TC meters in applications that require the adaptation of a Residential ERT or Cellnet AMR. The AMR Adapter is available as a conversion kit for field installation or factory installed on new meters.
General Information The Series B ROOTS meter is a positive displacement, rotary type gas meter designed for continuously measuring and indicating the accurate measurement of gas. ROOTS meters are suitable for handling most types of clean, dry, common gases at either constant or varying flow rates. Meters of standard construction are not directly suitable for handling acetylene, biogas or sewage gas. Contact the factory for information on specially constructed meters made of materials more compatible with these and other gases. Volumetric accuracy of the ROOTS meter is permanent, non-adjustable, and is not affected by low or varying line pressure. Series B meters may be used satisfactorily for pressures ranging from a few ounces to full Maximum Allowable Operating Pressure (MAOP). Displaced volume measurement is completely independent of the gas specific gravity, temperature, and pressure. Series B ROOTS meters have a MAOP rating of 75 psig (00kPa). Every meter is static pressure tested at the factory at twice its MAOP and leak tested at 5 percent of MAOP in accordance with ASME Boiler Pressure Vessel Codes. Other pressure ratings are available. Consult Factory. ROOTS meters are manufactured in accordance with ANSI B09. for Rotary Type Gas Displacement Meters. Series B ROOTS meter sizes 8C through 56M, have flanged inlet and outlet connections conforming dimensionally with ANSI/ASME standards. Sizes 8C through M are available with -/ NPT connections, upon special request. The meter operating temperature range is from -40 F to +40 F (-40 C to +60 C) while the temperature compensating mechanism of the TC accessory provides a corrected reading for temperatures ranging from -0 F to +0 F (-9 C to +49 C). Series B ROOTS meter bodies accept a wide range of Series accessories for all metering applications. AMR Adapters for Series B ROOTS Meter. AMR Adapter and ERT installed on a ROOTS Meter (top inlet meter installation shown)
Meter Specifications SERIES B Units 8C75 C75 5C75 M75 M75 5M75 7M75 M75 6M75 M75 M 8M75 56M75 Base Rating acfh 00 000 000 0 0 000 6000 000 000 0 56000 Max. Operating Pressure psig 75* 75* 75* 75 75 75 75 75 75 75 75 75 Rangeability +/-% ratio 6: : 40: 68: 76: 0: 67: 4: 6: 40: 69: 90: 5: Rangeability +/-% ratio 46: 58: 78: 6: 9: 5: 5: 7: : 60: 78: 0: 09: Start Rate acfh.79.0.94.9.. 5..9. 0. 7 40 Stop Rate acfh.0.74.57..8 0.8.4..9 8 5.75 0 9 Flow Rate, 0.5 w.c.,gas acfh 00 000 580 975 5400 9950 4 0948 0600 000 Differential, 00% Flow in.w.c. 0.45 0.6 0.75 0.65...6.06...08.9. Drive Rate, CD/TD cf/rev 0/00 0/00 0/00 0/00 0/00 0/00 0/00 0/00 00/000 00/NA 00/NA 00/NA 00/NA Min. CTR Reading cf 0. 0. 0. 0. 0. 0. 0. 0. Nominal Pipe Size in. 4 4 6 4 6 8 Flange/Flange Dim. in. 6-/4 6-/4 6-/4 6-/4 6-/4 6-/4 9-/ 9-/ 9-/ 6 9-/ 8 Oil Capacity: Side oz. 0.8 0.8 0.8... 40.4 40 40 Oil Capacity: Top oz. 7.6 7.6 7.6.9.9.9 54.8 54 54 Meter Sizing Model 8C75* C75* 5C75* M75* M75* 5M75* 7M75 M75 6M75 M75 M 8M75 56M75 Base Rating (acfh) 00 000 000 0 0 000 6000 000 000 0 56000 Meter Pressure (psig) Corrected Capacity at Metering Pressure - MSCFH 0.84..6.. 5. 7..5 6.7 4 4 9.7 58.5 5..5.6 4 6.6 9. 4.5. 0. 0. 50 7.8 5..9 4 5.4 8.4 8.7 9.4 4.8 6.5 6.5 0.7 49.8 60 4 5.6 7.6 0. 5. 5. 5.4 55.6 80.8 6. 6. 9.9 8.9 00 6. 8.5.7 5.5. 8.8 54.4 85.4 4. 78.6 78.6 95. 44.9 50 8.9. 7. 56 78 79 56.7 56.7 44. 65 75 0. 4. 9. 5.7 9 64 90 4 06 95.7 95.7 488.6 7.5 00.7 6.9 9. 4.7 7.8 4.8 84.7 *Available with 00 psig Rating. To select proper meter size, use Minimum Operating Pressure and Maximum Instantaneous Hourly Flow Rate. Complete Data Sheets are available for each meter size. Request Data Sheet by meter model. Roots Meters & Instruments Dresser, Inc. 640 Port Northwest Drive Houston, Texas 7704-645 USA Inside US Ph:.5.4 Fax:.5.54 Outside US Ph: 8.590.0 Fax: 8.590.494 009 Dresser, Inc. Roots, and Dresser are registered trademarks of Dresser, Inc. www.dresser.com TS:B 8.09
RotaRead Pulser Fits Roots Rotary B Style Meters Standard Conduit Connection /" NPT Output Connection for Conduit Standard Pulses/revolution RotaRead Model RMLL-CU-CF RotaRead (Dual Pulse Output) Installed on B TC Index Meter Type Roots Models 8C M Roots Models 6M 56M Resolution Available Single Pulse Output: Un-corrected: 5 cu ft/pulse pulses/revolution Temp.Corrected: 50 cu ft/pulse pulses/revolution Dual Pulse Output: Un-corrected and Corrected Single Pulse Output: Un-corrected: 50 cu ft/pulse pulses/revolution Temp.Corrected: 50 cu ft/pulse pulses/revolution Not available on M - 56M Temperature: Operational from -40 to +40 F Moisture: Operational to 00% humidity: Case is plated to protect from corrosion; all electronics are potted. Maximum switching voltage D.C.: 00 volts Maximum switching current D.C.:.5 amps Maximum switching watts D.C.: 0 watts Minimum voltage breakdown D.C.: 0 volts Contact resistance: 0. ohms Open circuit resistance: > 00,000,000 ohms Maximum rate contact closure:. pulses/sec Maximum bounce time: 0. ms max. Dual Pulse Output: Un-corrected and Corrected Resistance:00 ohms standard electric throughput resistance for interference suppression. Custom series and parallel values available. De-Bounce: RIO Tronics recommends a sec. debounce at host recorder's front end input for all RotaRead products. Patent# 4008458. Additional patents pending. RIOTronics Corp. reserves the right to modify features and specifications without notice. Wire Tamper Detection: RIOTronics provides various end of the line circuitry at the Form A switch to enable detection of breaks or shorts - please contact the company for custom solutions California 55 Arden Rd., Hayward, CA 94545 Tel: 50-5-9040 Fax: 50-5-07-446-88 Washington P.O. Box 98, Issaquah, WA 9807 Tel: 45-9-460 Fax: 45-557-084-58-8
AC-60 Commercial Diaphragm Meter The American Meter AC-60 diaphragm gas meter provides high capacity in a compact design. Long-term performance is proven with 40 years of craftsmanship that have gone into its development. AC-60 Die-cast aluminum case Molded duramic diaphragms Smaller meter profile Superior corrosion resistance Permanent lube bearings Automatic meter reader compatibility Temperature compensation available from - 0 F to 40 F 5 PSI MAOP 0 LT,0 LT,45 LT and #-4 Sprague connection sizes Full warranty Pointer or odometer index Pressure PSIG Rated Gas Capacity For 0.60 S.G. Gas Inches W.C. Differential Capacity SCFH.5 ½ 60.5 0 40 90 5 55 0 70 5 890 0 00 5 60 - Propane: 97 cfh California 00 Farallon Drive, San Leandro, CA 94577 Tel: 50-5-9040 Fax: 50-5-07-446-88 Washington P.O. Box 98, Issaquah, WA 9807 Tel: 45-9-460 Fax: 45-557-084-58-8
CMC- / CMC- Domestic Meter Pulsing Index Provides pulses from American Meter Co. domestic meters pulse per Cubic Foot Form A Contact Closure pulse For use with remote counter or data collection system The Miners & Pisani, Inc. CMC- and CMC- domestic meter pulsers are index mounted reed switch pulsers providing one contact closure per cubic foot for either the ft index (CMC-) or the ft (CMC-). Contact rating is 0W, 00 VDC. California 00 Farallon Drive, San Leandro, CA 94577 Tel: 50-5-9040 Fax: 50-5-07-446-88 Washington P.O. Box 98, Issaquah, WA 9807 Tel: 45-9-460 Fax: 45-557-084-58-8