ASB Accumulator Safety Blocks For working pressures up to 350 bar Catalogue HY07-1241/UK
Note: In line with our policy of continuing product improvement, specifications in this catalogue are subject to change without notice. 2
Introduction Contents Page Design Features 3 Technical data 3 Model ASB20 4 Model ASB32/64 7 Pressure Relief/Discharge Valve 13 Type Approval 13 Security 13 Adapters 14 Electrical Discharge Valve 14 Model Numbers 15 Safety Blocks The function of an accumulator safety block is to protect, to isolate and to discharge a hydraulic accumulator. Parker Hannifin's safety blocks provide safety and closing functions for operating pressures up to 350 bar. The pressure relief/discharge valves are CE marked in accordance with the European Pressure Equipment Directive 97/23/EC. Parker Safety Blocks are supplied in two different sizes, and are available with pressure relief/discharge valves which are suitable for flow rates up to 300 l/min at 330 bar on the largest size, ASB64. They are available with either manually- or electrically-operated discharge valves. Commissioning and maintenance of the safety block and associated equipment must be performed by qualified personnel. Design Features 1 Block 2 Accumulator port (A) adapter 3 Handwheel for manually-operated pressure relief/discharge valve 1 2 7 4 Shut-off valve 5 Pressure port (P) 6 Maintenance port (M1) 6 8 7 Maintenance port (M2) (not shown) 8 Tank port (T) (not shown) 4 5 3 Technical Data Construction pressure relief/discharge valve poppet-type valve with damping, manually-operated discharge shut-off valve ball valve electrically-operated discharge valve poppet-type valve Port type BSPP thread (flange port available for model NG32) Mounting position accumulator port A (see 2 above) facing upwards Mounting screws (not supplied) M8 to grade 10.9, max. torque 26 + 4Nm Ambient temperature -30 C to +80 C Max. operating pressure 350 bar Relief flow rate G at p nom see table on page 13 Fluid mineral oil according to DIN/ISO. For other fluid types, please contact the factory. Operating temperature -15 C to +80 C Viscosity 10 to 800 mm 2 /s Dp-Q-graphs see diagrams on pages 4 and 7 Electrical discharge U=24VDC, 105 VDC (for 115V/60 Hz AC supply), P=26W, % ED, IP 65 to DIN 40050, connector to DIN 43650 type A Surface zinc plated and passivated Seal material FPM 3
ASB20 ASB20 Safety Block The ASB20 accumulator safety block incorporates a manuallyoperated pressure relief/discharge valve, and is also available with an additional electrically-operated discharge valve see pages 5 and 6. The manual-only version, ASB20 type M, is denoted by an M in the model number, see page 15, while models with the additional electrically-operated discharge valve, ASB20 type E, are identified by the letter E. Both versions incorporate a lever-operated shut-off valve and the type SVH pressure relief/discharge valve shown on page 13. The cartridge design of the pressure relief/discharge valve allows it to be readily replaced by a valve with a different pressure setting. The pre-set pressure, in bar, is stamped onto the identification plate and follows the model number. A handwheel allows the pressure relief valve setting to be adjusted between zero and the pre-set maximum. Where frequent or remote operation of a discharge valve is required, an electrically-operated discharge valve should be specified. The block should always be mounted as close as possible to the accumulator. For diagnostic purposes and continuous pressure monitoring, the block has two ports M1 and M2. ASB20 Type M Manually-Operated Discharge Valve ASB20 Type E Manually- and Electrically-Operated Discharge Valves Dimensions and Weights Type A P T M1 M2 Weight kg Item Number 20 M M33x2 G1 G / 20 E M33x2 G1 G / xxx = pressure setting of pressure relief valve see page 13 A range of adapters is available for accumulator port A see page 14 1 2 G 1/ 2 G 1/ 4. 9 1 2 G 1/ 2 G 1/ 4. 4 5 ASB20MT5 - xxx 6 ASB20ET5 - xxx Flow Resistance Dp [bar] = f (Q A P ) 10 9 8 7 6 5 4 3 2 1 0 0 200 300 400 500 Q [l/min] Flow Resistance at Discharge Dp [bar] = f (Q A T ) 350 300 250 200 150 50 0 0 5 10 15 20 25 Q [l/min] 4
ASB20 Dimensions - ASB20MT5 Pressure relief/discharge valve shown only in this view Manual discharge Security seal Circuit Diagram Max. operating pressure p = 350 bar Adapter (see page 14) When assembling the lever, note orientation of washer and pin All dimensions are in millimetres unless otherwise stated. 5
ASB20 Dimensions ASB20ET5 Pressure relief/discharge valve shown only in this view Manual discharge Security seal Plug (connector included) PG11 Circuit Diagram Max. operating pressure p = 350 bar Adapter (see page 14) When assembling the lever, note orientation of washer and pin Connector to DIN 43650 A All dimensions are in millimetres unless otherwise stated. 6
ASB32/64 ASB32 Safety Block The ASB32 accumulator safety block incorporates a manuallyoperated pressure relief/discharge valve, and is also available with an additional electrically-operated discharge valve see pages 8-10. The manual-only version, ASB32 type M, is denoted by an M in the model number, see page 15, while models with the additional electrically-operated discharge valve, ASB32 type E, are identified by the letter E. Both versions incorporate a lever-operated shut-off valve and the type SVH pressure relief/discharge valve shown on page 13. The pressure port (P) is available with a BSPP thread or with a flange, denoted by a T or an F in the model number. The cartridge design of the pressure relief/discharge valve allows it to be readily replaced by a valve with a different pressure setting. The pre-set pressure, in bar, is stamped onto the identification plate and follows the model number. A handwheel allows the pressure relief valve setting to be adjusted between zero and the pre-set maximum. Where frequent or remote operation of a discharge valve is required, an electrically-operated discharge valve should be specified. The block should always be mounted as close as possible to the accumulator. For diagnostic purposes and continuous pressure monitoring, the block has two ports M1 and M2. A flange type adapter, available as an accessory, is required to fit the accumulator to the block see page 14. ASB64 Safety Block The ASB64 accumulator safety block is similar to the ASB32, but incorporates a second pressure relief/discharge valve to increase the relief flow rate. ASB64 safety blocks are illustrated on pages 11 and 12. ASB32 Type M Manually-Operated Discharge Valve Dimensions and Weights ASB32 Type E (Ports T & F) Manually- and Electrically- Operated Discharge Valves ASB64 Type E (Ports T & F) Manually- and Electrically- Operated Discharge Valves with Twin Relief Valves Type A P T M1 M2 32 M Flange 1 32 E (T port) Flange 1 xxx = pressure setting of relief valve see page 13 Flow Resistance Dp [bar] = f (Q A P ) G 1/ 2 1 G 1/ 2 1 Q [l/min] G G / G G / 32 E (F port) Flange DN32 G1 G / 64 E (T port) Flange 1 G 1/ 2 1 G G / 64 E (F port) Flange DN32 G1 G / 10 9 8 7 6 5 4 3 2 1 0 0 200 300 400 500 A G2 threaded adapter is available for accumulator port A see page 14 Flow Resistance at Discharge Dp [bar] = f (Q A T ) 350 300 250 200 150 50 Weight kg 1 2 G 1/ 4 4. 2 1 2 G 1/ 4 5. 1 1 2 G 1/ 4 4. 3 1 2 G 1/ 4 5. 9 1 2 G 1/ 4 5. 9 Item Number 1 ASB32MT5 - xxx 1 ASB32ET5 - xxx 1 ASB32EF5 - xxx 1 ASB64ET5 - xxx 1 ASB64EF5 - xxx 0 0 5 10 15 20 25 Q [l/min] 7
ASB32 Dimensions ASB32MT5 Adapter (see page 14) O-ring 40 x 3 incl. Circuit Diagram Max. operating pressure p = 350 bar When assembling the lever, note orientation of washer and pin Manual discharge Security seal Pressure relief/discharge valve shown only in this view All dimensions are in millimetres unless otherwise stated. 8
ASB32 Dimensions ASB32ET5 Adapter (see page 14) O-ring 40 x 3 incl. Circuit Diagram Max. operating pressure p = 350 bar Connector included When assembling the lever, note orientation of washer and pin Connector to DIN 43650 A Manual discharge Security seal Pressure relief/discharge valve shown only in this view All dimensions are in millimetres unless otherwise stated. 9
All dimensions are in millimetres unless otherwise stated. Adapter (see page 14) O-ring 40 x 3 incl. Connector included When assembling the lever, note orientation of washer and pin Dimensions ASB32EF5 ASB32 Catalogue HY07-1241/UK 10 Circuit Diagram After disassembly of flange, re-torque to specified figure O-ring 40 x 3 incl. Connector to DIN 43650 A Manual discharge Max. operating pressure p = 350 bar View at A M16 x 22 deep Pressure relief/discharge valve shown only in this view Security seal
ASB64 Dimensions ASB64ET5 Adapter (see page 14) Circuit Diagram Max. operating pressure p = 350 bar O-ring 40 x 3 incl. Connector included When assembling the lever, note orientation of washer and pin Connector to DIN 43650 A Manual discharge Security seal Pressure relief/discharge valve shown only in this view All dimensions are in millimetres unless otherwise stated. 11
All dimensions are in millimetres unless otherwise stated. Adapter (see page 14) O-ring 40 x 3 incl. Connector included When assembling the lever, note orientation of washer and pin Dimensions ASB64EF5 ASB64 Catalogue HY07-1241/UK 12 After disassembly of flange, re-torque to specified figure O-ring 40 x 3 incl. Connector to DIN 43650 A Manual discharge Circuit Diagram Max. operating pressure p = 350 bar View at A M16 x 22 deep Pressure relief/discharge valve shown only in this view Security seal
Pressure Relief/Discharge Valve Pressure Relief/Discharge Valve The function of the pressure relief/discharge valve is to protect the accumulator in service, and to enable the accumulator to be discharged manually by lowering the pressure relief valve setting to zero. Two versions of the pressure relief/discharge valve are available: the type SVH which is fitted with a handwheel, or the type SVK which is adjusted using a screwdriver. ASB20 and ASB32 safety blocks use type SVH pressure relief/ discharge valves, fitted with a handwheel. The ASB64 safety block uses two pressure relief/discharge valves; a type SVH and a type SVK, on which the adjustment screw is covered by a protective cap. Note: both valves must have the same pressure settings. Because of its cartridge design, the pressure relief/discharge valve can be readily replaced by a valve with a different pressure setting, selected from the table. A new approval under PED 97/23/EC is not required following this change. Note that the maximum flow rate for an ASB64 safety block is doubled because two pressure relief/discharge valves are fitted. Type Approval The pressure relief/discharge valve is checked and security sealed following approval, according to pressure vessel regulations. It carries a type approval number and a serial number. All valves are supplied with a certificate showing the pressure setting. The documents supplied with the pressure relief/discharge valve must be retained, as they will be required in the event of repeat tests. Security The pressure relief/discharge valve is locked with a tamperproof lead seal, to prevent any unauthorized increase of the pre-set pressure. Pressure Settings Pressure p bar Max Flow Rate G l/min Type SVH Item Number Type SVK 50 40 SVH050 SVK050 70 50 SVH070 SVK070 SVH SVK 120 SVH120 SVK120 140 SVH140 SVK140 160 SVH160 SVK160 200 SVH200 SVK200 210 SVH210 SVK210 250 130 SVH250 SVK250 280 130 SVH280 SVK280 300 130 SVH300 SVK300 330 150 SVH330 SVK330 Accessories Seals for the pressure relief/discharge valve can be ordered under part number SK-SVHK. The kit contains a sealing washer and two O-rings. Dimensions max. 65 56 Type Approval Number O-ring Sealing washer Type SVH Type SVK All dimensions are in millimetres unless otherwise stated. 13
Accessories Adapter for ASB20 Block Safety Block Accumulator D1 SW L L1 D2 D3 D1 Weight kg Part Number G 3 / 4 - ISO 228 46 33 16 53 16 0. 4 UEST20-3 / 4 Adapter for ASB32/64 Safety Block Accumulator D1 Weight kg D1 30 Part Number G1 1 / 4 - ISO 228 55 41 20 63 20 0. 4 UEST20-1 1 / 4 G2 - ISO 228 80 46 22 90 20 1. 5 UEST20-2 G2 - ISO 228 2. 2 UEST32-2 SW 20 50 L L1 18 (4 x) ÆD3 D2 Replacement Electrically-Operated Discharge Valve Model Weight kg Part Number 2/2 - Way Valve, 24VDC 0.35 EDV01 Seal Kit - SK-EDV 105 24 39 15 36 max. 102 All dimensions are in millimetres unless otherwise stated. 14
How to Order ASB Product Type Size Discharge Pressure Port Seal Compound Pressure Setting Code Size Page 20 NG20 4-6 32 NG32 7-10 64 NG64 7,11-12 Code Discharge M Manual E Electrical Code Pressure Port TThread F Flange Code Seal Page 5 FPM 12 Code Pressure Setting Page 50 70 120 140 160 Pre-set values for type-approved 200 pressure relief valves 13 210 250 280 300 330 15
Sales Offices Visit us at www.parker.com/uk Need a Parker Part? Call Parker's European Product Information Centre on 00800 27 27 5374 Austria Marchtrenk Parker Hannifin GmbH Tel: (7242) 569 21 Fax: (7242) 569 2120 Belgium Nivelles Parker Hannifin S.A. N.V. Tel: 67 280 900 Fax: 67 280 999 Czech Republic Prague Parker Hannifin Corporation Tel: 283 085 224 Fax: 283 085 360 Denmark Ishøj Parker Hannifin Danmark A/S Tel: 43 56 04 00 Fax: 43 73 31 07 Finland Vantaa Parker Hannifin Oy Tel: 9 476 731 Fax: 9 476 73200 France Contamine-sur-Arve Parker Hannifin S.A. Tel: 4 50 25 80 25 Fax: 4 50 03 67 37 Germany Cologne Parker Hannifin GmbH Tel: (221) 71720 Fax: (221) 7172219 Hungary Budapest Parker Hannifin Corp. Tel: 1 25 28 137 Fax: 1 25 28 129 Ireland Clonee Parker Sales (Ireland) Ltd. Tel: (353) 1 801 4010 Fax: (353) 1 801 4132 Italy Arsago-Seprio Parker Hannifin S.p.A. Tel: (0331) 765611 Fax: (0331) 765612 Netherlands Oldenzaal Parker Hannifin B.V. Tel: (0541) 585000 Fax: (0541) 585459 Norway Ski Parker Hannifin A/S Tel: 64 91 10 00 Fax: 64 91 10 90 Poland Warsaw Parker Hannifin Corp. Tel: (22) 863 49 42 Fax: (22) 863 49 44 Portugal Leca da Palmeira Parker Hannifin Portugal Lda. Tel: (22) 999 7360 Fax: (22) 996 1527 Slovakia Ref. Czech Republic Spain Madrid Parker Hannifin España S.A. Tel: (91) 675 73 00 Fax: (91) 675 77 11 Sweden Spånga Parker Hannifin AB Tel: 08-5979 50 00 Fax: 08-5979 51 10 Switzerland Romanshorn Hydrel A.G. Romanshorn Tel: (714) 66 66 66 Fax: (714) 66 66 80 Turkey Istanbul Hidroser Hidrolik - Pnömatik Tel: (212) 886 72 70 Fax: (212) 886 69 35 United Kingdom Watford Parker Hannifin Plc Tel: (01923) 492000 Fax: (01923) 248557 1241/2-UK 1M PD 11/02