T.S0- Miniature Tubin & Miniature Fittins Series TU/M O.D. ø x I.D. ø. Minimum bendin radius mm Tubin olor Variations lack White Red lue Yellow reen lear Four types of fittins are available. arb fittin arb elbow arb one-touch Reducer M x 0. M x 0. Tubin size ø. ø Fittin size ø. ø
Pipin for compact actuator Scale :00% Scale :00% Scale :00% Pipin for compact pressure sensor ø x Scale :00% ø % Reduction Sectional area.0mm ø x ø Sectional area 8.6mm asy size reduction Reduction of the tubin size from standard equipment is possible in a sinle step. arb one-touch ø.,ø ø.,ø ø ø Reducer Features
Miniture Polyurethane Tubin Series TU Specifications Fluid Max. operatin pressure (at 0 ) urst prssure Min. bendin radius (mm) ) Operatin temperature olor TU0 x. ir, Water 0.8MPa Refer to pressure characteristics curve. 0 to +60 (Water: 0 to 0 ) (No freezin) Polyurethane lack(), White(W), Red(R), lue(u), Yellow(Y), reen(), lear() ffective area (mm ) ffective sectional area 0. 0. 0. 0. 0. 0 Tubin lenth Fixed side R ) t a temperature of 0 bend the tubin into a U shape. Then with one side fixed, radually close the other side and measure R at the point where the tubin folds or flattens, etc. urst Pressure haracteristic urve and Operatin Pressure urst pressure MPa.0.0.0.0.0 urst pressure Maximum operatin pressure 0 0 0 0 0 60 Operatin temperature Precautions e sure to read before handlin. Refer to pae throuh 6 for Safety Instructions and common precautions on the products mentioned in this catalo. aution pplicable for eneral industry water. onsult SM if usin for other kinds of fluids. Sure pressure must be under the max. operatin pressure. If exceedin that value, fittin may damaed and tubin may burst. The value of the max. operatin pressure is at a temperature of 0. Refer to the burst pressure characteristics curve for other temperatures. void abnormal temperature rises which may burst the tubin. The values of the min. bendin radius is at a temperature of 0. Hiher temperatures allows the tubin to bend more. How to Order TU0 0 Indication of tubin model olor indication Symbol W R U Y olor lack White Red lue Yellow reen lear Lenth per roll Symbol 0 Roll size 0m roll
Miniature Fittins (For exclucive Miniature tubin) Series M arb asy tube insertion Hih retainin force Tubin Tubin connection and removal Installin tubin. ut the tubin perpendicularly allowin additional lenth.. Insert the tubin into the sleeve. ody ttachin the sleeve achieves a lare retainin force. Detachin it allows easy removal of the tube... Insert the tubin slowly into the fittins. Make sure to secure a ap of approx. 0.mm between the tubin end and the barb end. ap (approx. 0.mm) Specifications Low clampin torque. Insert the sleeve slowly. Make sure not to allow any ap between the sleeve end side and the body end side. (Please refer to the illustration below.) If you feel any stron resistance and cannot push the sleeve completely to the end side, this may be caused due to jammin. Remove and repeat aain by startin from step makin sure to secure a ap in the step. ) When installin the tubin, the sleeve must be attached. Operation without attachin the sleeve may cause tubin disconnection. There should not be any ap. pplicable tube material pplicable tube dia. Max. operatin pressure (at 0 ) Miniature fittin Polyurethane ø/ø. MPa M, M, ø., ø JIS 009 lass (Metric coarse thread) How to order M U pplication tubin (O.D. / I.D.) ø/ø. Removin tubin Withdraw the sleeve straiht alon the tubin. Use a tool such as lon-nose pliers if it is difficult to pull out by hand.. Withdraw the tubin straiht.. When reusin the tubin, cut off the previously installed portion of the tubin to avoid possible leakae and/or disconnection of the tubin. 0 U LU LHU F R M x 0. ø. ø arb fittin arb elbow arb one-touch Reducer M, M M M ø., ø
F J I Series M arb fittin: M-U-, M-U- pplicable tubin ø x ø. M x 0. M-U- M-U- H. 9 0 D. F 0.9 0.. pplicable tubin arb fittin rass rass NR, Stainless steel øf arb elbow: M-LU-, M-LHU- Width across flats H pplicable tubin ø x ø. M x 0. M-LU- M-LHU- H 9 6.. D F 0.9... I 9.. J.6. Stud arb elbow rass rass rass NR, Stainless steel Width across flats H pplicable tubin arb one-touch: M-F-, M-0F- pplicable tubin (mm) a (O.D. x I.D.) b (O.D.) ø x ø. ø. ø M-F- M-0F-. 8.. 8. D M 0.9...9 ody Seal assette rass rass NR POM, Stainless steel ø pplicable tubin b M pplicable tube a Reducer: M-R-, M-0R- pplicable tubin ø x ø. Fittin size ø. ø M-R- M-0R- 6 6. F. 0. 0.9 0. 0.8 Studded body Stem rass rass PP pplicable fittin size pplicable tubin øf