50 it Installation Instructions SF-TIN RN QUIPNT UNIVRS INPUT! IPORTNT SFURDS! WHN USIN TRI QUIPNT, SI SFT PRUTIONS SHOUD WS FOOWD, INUDIN TH FOOWIN: RD ND FOOW SFT INRUTIONS 1. To prevent high voltage from being present on red & yellow output leads prior to installation, inverter connector must be open. Do not join inverter connector until installation is complete and power is supplied to the emergency ballast. 2. This product is for use with one 17 W through 215 W (2-8 ) or two 17 W through 40 W (2-4 ) single pin or bipin fluorescent lamps, including standard, energy saving, HO, VHO, circline, U-shaped and rapid-start (4-pin) long compact fluorescent lamps. 3. ake sure all connections are in accordance with the National lectrical ode or anadian lectrical ode and any local regulations. 4. To reduce the risk of electric shock, disconnect both normal and emergency power supplies and inverter connector of the emergency ballast before servicing. 5. This emergency ballast is for factory or field installation in either the ballast channel, on top of, or remote from the fixture. 6. This product is suitable for damp locations where the ambient temperature is 0 minimum, +50 maximum. Product is also suitable for installation in sealed and gasketed fixtures. Product is not suitable for heated air outlets and wet or hazardous locations. 7. n unswitched power source is required. (120 through 277 V, 50/60Hz) 8. Do not install near gas or electric heaters. 9. Do not attempt to service the battery. sealed, no-maintenance battery is used that is not field replaceable. ontact the manufacturer for information on service. 10. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition. 11. Do not use this product for other than intended use. 12. Servicing should be performed by qualified service personnel. SV THS INRUTIONS Ni - d THIS PRODUT ONTINS RHR NI-DIU TTR. TH TTR U RD OR DISPOSD OF PROPR. 05/18/12 Philips mergency ighting Division of Philips lectronics North merica orporation 236 t. Pleasant Rd. ollierville, TN US 38017-2752 Tech Support 888-263-4638 Fax 901-854-1630 www.bodine.com 75000045
INTION WRNIN: TO PRVNT HIH VOT FRO IN PRSNT ON & OW OUTPUT DS PRIOR TO INTION, INVRTR ONNTOR U OPN. DO NOT JOIN INVRTR ONNTOR UNTI INTION IS OPT ND POWR IS SUPPID TO TH RN. NOT: ake sure the necessary branch circuit wiring is available. n unswitched source of power is required. The emergency ballast must be fed from the same branch circuit as the ballast. P #1 ININ TH RN > Disconnect power from the fixture. Remove the ballast channel cover and install the emergency ballast either in the ballast channel or on top of the fixture.* Remote mounting distance must be less than half the maximum remote mounting distance for the ballast. onsult ballast manufacturer before remote installation. > Depending on the type of fixture in use install emergency ballast using one of the methods illustrated below. INSID Inside allast hannel HNN INSID Inside RIP Strip Fixture FIXTUR ON On TOP Top OF of Fixture FIXTUR * For installation on top of the fixture, wire bundle covers (R-60) may be required by state or local codes. These covers are available from the manufacturer as an accessory kit and must be ordered separately. all your local distributor or the factory for complete information. P #2 ININ TH T > Refer to the illustrations above and install the test switch through the ballast channel cover of a troffer or through the side of a strip fixture. Fixture Test utton Hex Nut Test Switch > Drill a 1/2 hole and install the switch as shown. > Wire the test switch so that it removes power from both the emergency ballast and the ballast at the same time. (see wiring diagrams) Push to Test eads Hex Nut P #3 ININ TH HRIN INDITOR IHT > Install the HRIN INDITOR IHT as shown in the illustration on the following page so that it will be visible after the fixture is installed. 2
HRIN INDITOR IHT INTION TROFFR FIXTUR RIP FIXTUR Fixture Fixture harging Indicator ight harging Indicator ight Violet (+) Violet (+) rown ( ) rown ( ) 1/2" White ushing 1/2" Punch 5/8" lack ushing 1/2" White ushing 5/8" lack ushing P #4 WIRIN TH RN > Determine the type of ballast installed in the fixture. > Select the appropriate wiring diagram on back to connect the emergency ballast to the ballast and lamp(s). ake electrical connections in accordance with the National lectrical ode and any local regulations. > fter installation is complete, supply power to the emergency ballast and join the inverter connector. It is normal for the indicator light to remain off for a few minutes on initial start-up, as the battery voltage rises to normal range. Refer to Troubleshooting uide if this condition persists. > t this point, power should be connected to both the ballast and the emergency ballast, and the harging Indicator ight should illuminate indicating the battery is charging. > short-term discharge test may be conducted after the emergency ballast has been charging for one hour. harge for 24 hours before conducting a long-term discharge test. Refer to OPRTION. > In a readily visible location, attach the label UTION - This Unit Has ore Than One Power onnection Point. To Reduce The Risk Of lectric Shock, Disconnect oth The ranch ircuit-reakers Or Fuses nd mergency Power Supplies efore Servicing. OPRTION During normal operation, power is applied and the self-testing emergency ballast charges the battery. onnecting the (red and white) inverter connector wires enables the emergency circuit, and supplies power to the control/monitor circuit and charging indicator light. The self-testing emergency ballast continually monitors the charging current and battery voltage, comparing them to preset limits. Should the unit detect an unusual current or voltage condition, the indicator light will flash a pattern as mentioned in the troubleshooting guide until the condition has been corrected or the unit passes the next test. When power fails, the self-testing emergency ballast automatically switches to emergency mode, keeping either one or two lamps illuminated at a reduced lumen output for a minimum of 90 minutes. When power is restored, the self-testing emergency ballast returns to charging mode and delays ballast operation for approximately three seconds to prevent false tripping of ballast (end-of-lamp life) shutdown circuits. SF-TIN OPRTION This unit contains a control/monitor circuit that automatically performs a 30-second discharge test every 30 days, and a full 90-minute discharge test once a year. During routine testing, the self-testing emergency ballast simulates an power failure causing the unit to automatically switch to emergency mode. The unit will monitor the operation of the lamps, battery voltage, discharge current, and emergency duration. If the emergency system functions properly, then the unit will return to normal mode. Should the unit detect any problems, the indicator light will flash a pattern as mentioned in the troubleshooting guide until the condition has been corrected or the unit passes the next test. To reset a failure indication, push and hold the test switch for a minimum of 15 seconds. If the condition has not been corrected by the next scheduled test, the unit will once again detect the failure and signal the failure indicator. To cancel a test, turn the wall switch ON (or OFF if switch is already on), wait five seconds, then turn it OFF (ON). 3
INTNN This self-testing emergency ballast automatically performs required routine testing. Results are reported to maintenance personnel via the indicator light. Note: aintenance personnel should periodically check the indicator light. If the indicator light is flashing, go through all steps of Troubleshooting uide. TROUSHOOTIN UID TUS INDITOR PRO ORRTIV TION ight on steady, not flashing None None, Unit is Operating orrectly. Flashing 2 times every 10 seconds attery voltage is outside limits et battery charge. If after an hour failure is still indicated, see action below. Flashing 3 times every 10 seconds attery charging current is outside limits heck that fixture wiring is in accordance with proper wiring diagram. Flashing 4 times every 10 seconds ontinuous fast flashing attery discharge is too low during scheduled self test attery discharge is too high during scheduled self test 1. heck to make sure lamps are good (operational and specified for self-testing emergency ballast) and in place. 2. heck to see if brown connector is properly used. (See Table 1.) 3. heck that fixture wiring is in accordance with proper wiring diagram. 4. llow unit to charge for 24 hours. Perform manual test. If flashing continues, emergency ballast should be replaced. Failure Status will be reset when the unit passes: The next automatic test, or manual test exceeding 15 seconds, or n actual power failure exceeding 15 seconds. 4
50 WIRIN DIRS The following diagrams are typical schematics only. ay be used with other ballasts. onsult the factory for other wiring diagrams. mergency allast and allast must be fed from the S RNH IRUIT. IPORTNT TXT: RFR TO T 1 RRDIN ROWN ONNTOR Table 1 ROWN ONNTOR OPN ROWN ROWN ROWN ONNTOR OSD JUPR WIR ROWN ROWN P (DITR) T8,T9,T10,T12 (1, 1¼, 1½ ) ON OPT S TP Single or ipin 4-PIN (211) WTT (ength) 17-40 W (2'-4') 40-215 W (5' -8') 18-39 W NO. of PS (RN- OD) ROWN ONNTOR 1 OSD 2 OPN 1 OPN 1 OSD 2 OPN 40-55 W 1 OSD WIRIN DIR for 1-P emergency operation FI ON (1) P RPID RT FI ON (1) P INNT RT W W T INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN WRNIN: Refer to Table 1 before connecting ROWN OW P / U/WHT U U U 1 P RPID RT T INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN ROWN OW / U/WHT U U WRNIN: Refer to Table 1 before connecting P 1 P INNT RT FI TWO (2) P RPID RT FI D TWO (2) P INNT RT W W T INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN ROWN OW / U/WHT U U U 2 P RPID RT WRNIN: Refer to Table 1 before connecting OW OW P 1 ( RN) P 2 T INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN ROWN OW / U/WHT U U WRNIN: Refer to Table 1 before connecting P 1 ( RN) U P 2 2 P INNT RT FI THR (3) P RPID RT FI F THR (3) P INNT RT W W T INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN ROWN OW / U/WHT U U U 3 P RPID RT WRNIN: Refer to Table 1 before connecting U/WHT OW OW U/WHT P 1 ( RN) P 2 P 3 T INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN ROWN OW / U/WHT U U 3 P INNT RT WRNIN: Refer to Table 1 before connecting U U P 1 ( RN) P 2 P 3 FI FOUR (4) P RPID RT FI H FOUR (4) P INNT RT W W T INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN ROWN OW / U/WHT U 4 P RPID RT WRNIN: Refer to Table 1 before connecting OW OW U/WHT U/WHT RN RN U U P 1 ( RN) P 2 P 3 P 4 T INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN ROWN OW / U/WHT U U 4 P INNT RT WRNIN: Refer to Table 1 before connecting OW U OW P 1 ( RN) P 2 P 3 P 4 5
FI I RN ND U FD FRO TH S RNH IRUIT TPI SHTIS ON. USD WITH OTHR S. ONSUT TH FTOR FOR OTHR WIRIN DIRS. WIRIN DIR for 1-P emergency operation ON (1) P OPT RPID RT FI J TWO (2) P OPT RPID RT W T INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN WRNIN: Refer to Table 1 before connecting ROWN OW / P U/WHT U U U 1 P RPID RT T W INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN ROWN OW / U/WHT U U U 2 P RPID RT WRNIN: Refer to Table 1 before connecting OW OW P 1 ( RN) P 2 FI TWO (2) P RPID RT P DIIN WHT/ INVRTR ONNTOR VIOT (+) HRIN INDITOR ROWN (-) T WHT/ S1 S2 R N ROWN ROWN OW / U/WHT U U U 2 P RPID RT P DIIN WRNIN: Refer to Table 1 before connecting OW OW P 1 ( RN) P 2 TH / D U ONNT TO TH D OF TH P-DIIN SSOITD WITH TH RN ON. ONNTIONS TO OTHR S OR FIXTURS OUD RSUT IN NOR OPRTION ND US PRODUT D. WIRIN DIRS for 2-P emergency operation (2-4, 17-40 W lamps only) Two-lamp emergency operation is not possible with all ballasts. onsult the factory for any ballast other than those shown. FI TWO (2) P RPID RT FI TWO (2) P INNT RT T W INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN WRNIN: Do NOT connect brown connector ROWN OW P 1 / U/WHT U U U P 2 2 P RPID RT OW OW T W INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN ROWN OW / U/WHT U U WRNIN: Do NOT connect brown connector P 1 U P 2 2 P INNT RT FI N THR (3) P RPID RT FI O THR (3) P INNT RT W W T INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN ROWN WRNIN: Do NOT connect brown connector OW P 1 ( RN) / U/WHT U U/WHT U U U/WHT OW P 2 ( RN) 3 P OW RPID RT P 3 T INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN ROWN OW / U/WHT U U 3 P INNT RT WRNIN: Do NOT connect brown connector U U P 1 P 2 P 3 ( RN) ( RN) FI P FOUR (4) P RPID RT FI Q FOUR (4) P INNT RT T W INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN WRNIN: Do NOT connect brown connector ROWN OW P 1 ( RN) / U/WHT OW U OW U/WHT P 2 ( RN) U/WHT 4 P RPID RT P 3 RN RN U P 4 U T W INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN ROWN OW / U/WHT U U WRNIN: Do NOT connect brown connector P 1 ( RN) OW U P 2 ( RN) 4 P INNT RT P 3 OW P 4 FI R TWO (2) OPT P RPID RT W T INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN WRNIN: DO NOT connect brown connector ROWN OW / P 1 U/WHT U OW U U 2 P RPID RT OW P 2 6
WIRIN DIRS for mergency-only fixtures FI S ON (1) P WITHOUT (16W-215W) FI T TWO (2) PS WITHOUT (17W-40W) T (P) INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) R N ROWN ROWN OW / U/WHT U (P) (P) WRNIN: Refer to Table 1 before connecting P T (P) INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) R N ROWN ROWN OW / U/WHT U (P) (P) WRNIN: Do NOT connect brown connector P 1 P 2 (P) WHT/ (P) WHT/ FI U ON (1) 4-PIN OPT P WITHOUT (16W-55W) FI V TWO (2) 4-PIN OPT PS WITHOUT (16W-39W) T (P) WHT/ INVRTR ONNTOR HRIN VIOT (+) INDITOR ROWN (-) (P) WHT/ R N S T ROWN ROWN OW / U/WHT U (P) (P) WRNIN: Refer to Table 1 before connecting P T (P) WHT/ INVRTR ONNTOR HRIN VIOT (+) INDITOR ROWN (-) (P) WHT/ R N S T ROWN ROWN OW / U/WHT U (P) (P) WRNIN: Do NOT connect brown connector P 1 P 2 7