MOYNO FLUID DETECTION CONTROL SERVICE MANUAL. Section: ACCESSORIES. Page: 1 of 8 Date: May 1, 1998 GENERAL
|
|
- Gerard Mitchell
- 6 years ago
- Views:
Transcription
1 MOYNO Section: ACCESSORIES Page: 1 of 8 Date: May 1, 1998 SERVICE MANUAL FLUID DETECTION CONTROL GENERAL The Moyno Fluid Detection Control prevents unnecessary loss of production time or repair costs to positive displacement pumps or other fluid process equipment when they are subjected to run dry conditions or high-pressure conditions. The control works equally well on high and low viscosity fluids, suspended solids, abrasive, corrosive and volatile liquids. The product consists of three basic components: a sensor, a pressure switch and a control box. The sensor, available from 1" to 14", fits between two standard ANSI pipe flanges and allows complete fluid flow without obstruction. There are no drilling, tapping, special tools or sealants required for installation. Pressure transmission over the entire pipe circumference ensures that coating, settled material or bridging in the pipe line does not affect pressure readings. As an added feature, a liquid-filled gauge allows visual monitoring of pressure conditions. This control will also control and monitor seal flush water.
2 Page 2 PRINCIPLES OF OPERATION The Fluid Detection Control ensures that pumps operate within design parameters, protecting them from overpressure, run dry conditions and loss of seal water. Although designed primarily for use with progressing cavity pumps, the Control may be used with other equipment as well. The pump starter is wired directly to the control box. A double pressure switch is installed in the discharge line of the pump. The high-pressure switch must be set to the highest safe operating pressure for the process system. If the pump discharge pressure exceeds the setting of the high-pressure switch, the pump will stop and the HIGH lamp on the front of the control box will illuminate. The pump will remain stopped until the Stop/Reset or External Stop pushbutton is pressed. The pump can be restarted if the pressure has been relieved. The control box protects the pump against run dry conditions by using a low pressure switch. This ensures that a certain minimum pressure is maintained in the system. It is very important that this switch be properly set. In order to set this switch, it is necessary to understand the difference between static, friction and total pressure. Static pressure is the pressure which results from the pipe being filled with liquid, and is present even when the pump is idle. Static pressure is not influenced by pipe size, number of fittings, or viscosity. Static pressure is determined by the difference in height between the pressure switch and the outlet of the piping. Friction pressure is the pressure which results from the flow of liquid through a pipe, and is present only when the pump is actually operating. It is dependent on the flow rate, the size of pipe, the length of pipe, the number of fittings, and the viscosity of the fluid. Total pressure is the combination of the static and friction pressures. In an existing installation, these pressures can be obtained by observing the gauge on the pump discharge. When the pump is idle, the gauge shows static pressure. When the pump is operating and there is flow present, the gauge shows total pressure. For run dry protection, the low pressure switch is set between the static and the total pressure. When the pump runs, the switch signals the control box that flow is present. If the pump runs dry and flow stops, the pressure falls back to the static pressure. This causes the low pressure switch to signal the control box that flow has stopped. The pump will stop and the lamp on the front of the control box will illuminate. The pump will remain stopped until the STOP/RESET or External Stop pushbutton is pressed. The pump can be restarted after the cause of the run dry has been identified. Typical Example: If the pressure gauge in the discharge line reads 22 psi when the pump is idle, and the gauge reads 32 psi when the pump is running, set the low switch to 27 psi (half way between low and high) and set the high switch to 37 (high pressure +5 psi). Pumps that require seal water, a flow switch can be installed to monitor loss of flow. The pump will stop and the SEAL WATER lamp on the front of the control box will illuminate. The pump will remain stopped until the STOP/RESET button is pressed. SWITCH SELECTION The unit consists of two separate snap action switches, each with an independently adjustable set point and nonadjustable reset point. The difference between the set and reset points of each switch is the deadband as listed below; the minimum difference to which the two switches may be set is the separation. Determine the pressure range needed. Check that rated overrange pressure is sufficient. Separation Maximum - Full Range Rated Fixed Adjustable Overrange Deadband Minimum - Operating Pressure As Listed As Listed Range (PSIG) Below Below PSIG PSIG 1.8 PSIG PSIG PSIG 3.6 PSIG 2-60 PSIG PSIG 6 PSIG PSIG PSIG 10 PSIG PSIG PSIG 20 PSIG PSIG PSIG 30 PSIG PSIG PSIG 40 PSIG SIMPLE CALIBRATION The pressure sensor is supplied with sensing liquid and requires no calibration. The pressure switch is preset for the operating conditions. Final field calibration of the pressure switches is recommended, and can be performed with 7/16" open end wrench.
3 LOCAL REMOTE STOP/ RESET POWER ON HIGH SEAL WATER Page 3 Fluid Detection Control APPLICATION REQUIREMENTS* SWITCH SWITCH SENSOR SENSOR ENCLOSURE RANGE ELASTOMER HOUSING MATERIAL NEMA PSIG NITRILE CARBON NEMA 7/ PSIG EPDM STEEL PSIG NEOPRENE STAINLESS PSIG HYPALON STEEL PSIG FLUORO CUSTOMER: FOR: CUSTOMER NO: DATE: CERTIFIED: MOYNO SENSOR SIZE / / OPTIONAL ALARM SWITCH SETTING () (HIGH) *All the above requested information is necessary for the completion of your order. A copy of this page may be submitted with your order /4 N.P.T. CONDUIT CONNECTION (BOTH ENDS) ACCURACY: ANSI GRADE B 4 X Ø.31 THRU (8) SENSOR DIMENSIONS SIZE A-DIA. B THICKNESS 1 2-1/2 1-7/8 1-1/2 3-1/4 2-3/4 1-7/ /8 2-1/2 4-3/4 1-7/ /4 1-7/ /4 2-1/ /8 3-3/4 2-1/ /8 2-1/ /4 2-13/ / /8 3-1/ (152) ALL DIMENSIONS IN INCHES FLUID DETECTION CONTROL B (273) SENSOR FITS INSIDE BOLT PATTERN OF MATING FLANGES MOYNO A TUBE I.D. MATCHES SCH. 40 CARBON STEEL PIPE UNIT HAS GASKETS MOLDED IN. NO ADDITIONAL GASKET REQUIRED 8.91 (226) CONTROLS: NEMA 4 ENCLOSURE STANDARD SIGNAL LIGHTS ADJUSTABLE TIME DELAY 0-60 SEC 1/60/115 VOLT POWER REQUIRED TERMINAL STRIPS FOR WIRING ALARM OPTIONAL BOX DEPTH: 6.87 (2) 3/4 NPT CONDUIT CONNECTIONS
4 Page 4 Typical Wiring Diagram (OPTIONAL) ADDITIONAL STOP/RESET PUSH BUTTON N/C (REMOVE JUMPER IF ADDITIONAL SWITCH IS USED). JUMPER OR N/C SWITCH MUST BE USED OR STOP/RESET LIGHT WILL BLINK (OPTIONAL) REMOTE /STOP (PLC OR DCS) TWO SELECTIONS (SEE SET-UP) 1. HI-N/O -N/C SEAL WATER-N/O *2. HI-N/C -N/O SEAL WATER-N/C * SWITCHES UTILIZE BROKEN WIRE DETECTION. IF SEAL WATER F SWITCH IS USED, REMOVE JUMPER AT TB2-9 AND 10. NOTE: ELECTRICAL INSTALLATION SHOULD BE PERFORMED BY QUALIFIED PERSONNEL. INSTALLATION MUST CONFORM TO LOCAL AND NATIONAL CODE. { HI SWITCH SWITCH (OPTIONAL) SEAL WATER F SWITCH (OPTIONAL) EXTERNAL ADDITIONAL LOCAL PUSH BUTTON N/O (OPTIONAL) SEAL WATER SOLENOID VALVE 120 VAC PUMP MOTOR (OPTIONAL) ALARM HORN 120 VAC 120 VAC FIELD WIRING TBI L1 N TB TB TB PUMP RUN CONTACT HIGH RELAY RELAY SEAL WATER RELAY FLUID DETECTION CONTROL CIRCUIT BOARD INPUTS CONTACTS OUTPUTS CONTACTS SPECIFICATIONS ENCLOSURE RATING: SUPPLY VOLTAGE: AC LINE VOLTAGE VARIATION: OUTPUT CONTACTS: INPUT CONTACTS: WIRE SIZE: AMBIENT TEMPERATURE: RELATIVE HUMIDITY: ALTITUDE: NEMA VAC 50/60 HZ 1PH +10 TO -5% 5A 250 VAC DRY CONTACTS 14 AWG MAXIMUM -20 TO 120 F -5 TO 95% (WITHOUT CONDENSATION) TO 5160 FT.
5 Page 5 Typical Block Diagram 120VAC STOP LOGIC BOARD DCS OR PLC HI PUSHBUTTONS LOCAL REMOTE ALARM HORN STOP/ RESET ALARM LIGHTS HI SEAL WATER SEAL WATER F FLUID DETECTION CONTROL FIELD SWITCHES SEAL WATER SOLENOID VALVE 3 Ø POWER PUMP MOTOR ER OR VFD MOTOR PUMP
6 Page 6 SYSTEMS ADAPTABILITY The system can be adapted to meet a variety of system requirements: temperature ranges from -20 F to +300 F, elastomers to provide the best combination of chemical and abrasion resistance characteristics, operating pressures from 5 to 300 PSI. There are certain situations where it is impractical to install the low-pressure switch on the discharge side of the pump. An example would be several pumps that discharge into a common header. Here, the discharge pressure from one pump creates an erroneous reading at the low-pressure switch of the adjacent pump. Other installations not suitable for low pressure detection are pumps that discharge into the bottom of a tank, systems that generate little or no friction pressure, and systems with excessively long discharge piping. Progressing cavity pumps are capable of compressing air after it is empty. The pressure will not drop until after the discharge piping is empty. SET-UP Connect the Fluid Detection Control Box as shown on the Typical Wiring Diagram. The HIGH,, and SEAL WATER flow switches can be connected two ways. (See Typical Wiring Diagram) 1. HIGH -N/O -N/C SEAL WATER F -N/O 2. HI -N/C -N/O SEAL WATER F -N/C While Method One is most often used, Method Two will activate the fault lights, while the pump is running, if a wire is broken between the pressure switches and The Fluid Detection Control Box. See Table 4 of Setup. The Fluid Detection Control box has three setable timers. 1. Pressure Fault Timer - This timer is adjustable from seconds. When the pump is started, the timer allows a set period to elapse before checking for low pressure/run dry conditions. During this time period, the light will blink. After this timeout period, if the pressure falls below the setting of the low-pressure switch, the pump stops and the light is lit. The factory setting is 30 seconds. 2. HI Pressure Fault Timer - This timer is adjustable from seconds. In some instances a pump is capable of generating high-pressure spikes at startup. When the pump is started, the timer allows a very short period to elapse before checking for high-pressure conditions. The factory setting is 0 seconds. After this time-out period, if the pressure rises above the setting of the HI pressure switch, the pump stops and the HI light is lit. 3. SEAL WATER F Timer - This timer is adjustable from 5-30 seconds. When the pump is started, the timer allows a set period to elapse before checking for Seal Water Flow. During this time period, the SEAL WATER light will blink. After this timeout period, if Seal Water Flow is not established, the pump stops and the SEAL WATER light is lit. The factory setting is 5 seconds. To reset timers for other than factory settings and switches connections for, HIGH and SEAL WATER Faults see Tables 1, 2, 3 and 4 and follow the seven steps listed below. 1. Stop the pump by pressing STOP/RESET button. CAUTION 115 VOLTS INSIDE CONTROL BOX 2. Open door of Fluid Detection Control box and locate DIP switch on the inside of the door. This small switch has four rockers. 3. Set the DIP switches to match either Table 1, 2, 3 or 4. Table 1: Low-Pressure Timer Table 2: High-Pressure Timer Table 3: Seal Water Timer Table 4: Switch Connections 4. Match the three red fault lights to the table to determine current settings that the Fluid Detection Control box is currently set. Table One - Example, if all three lights are off, the low-pressure fault timer is set at 10 seconds. 5. Press the LOCAL pushbutton to change settings if desired. 6. Repeatedly press LOCAL until the fault lights match the desired settings. 7. After the correct setting has been selected, turn all DIP switches OFF before restarting the pump. If another setting needs to be changed, set the DIP switches to the next table and repeat steps 4 through 7. The Alarm Test Mode enables the Fluid Detection Control alarm output relays to be operated without starting the pump and jumping around the pressure or flow switches. To operate the Alarm Test Mode, follow the steps listed below: 1. Stop the pump by pressing STOP/RESET button. 2. Open door of the Fluid Detection Control box and locate the DIP switches on the inside of the door. 3. Set the DIP switches to match Table Press the associated buttons to perform the listed functions on Table Turn all DIP switches OFF to return the Fluid Detection Control box to normal operating mode.
7 Page 7 OPERATIONAL DETAILS When the pump is off and the STOP/RESET light is on, the pump is ready to be started. Start or stop the pump by pressing the LOCAL or STOP/RESET buttons on the front panel. A green light at the LOCAL button will light after pressing LOCAL. In the event of a malfunction, the STOP/RESET button is used to clear any fault condition indicated by three fault lights on the front panel. REMOTE is used for operating the pump using a Programmable Logic Controller (PLC) or Distribution Control System (DCS). Terminals 3 and 4 of TB2 must be connected to either a PLC or DCS for REMOTE to be functional. Press the REMOTE button. A yellow light at the REMOTE button will light indicating that the system is being controlled by a PLC or DCS. While the REMOTE light is on, the pump cannot be started with the LOCAL button or any additional start pushbuttons connected to terminal 11 and 12 of TB2. All STOP buttons can be used to stop the pump while running with REMOTE. The STOP/RESET light will be lit when the pump is off. If a fault occurs while the pump is controlled by a DCS or PLC, the REMOTE light will go off, the STOP/RESET will light and 1 of 3 fault lights will be illuminated. Press the STOP/RESET button to clear the fault and restart the pump using LOCAL or REMOTE. TABLE 1 TABLE 2 TABLE 3 - TIME LIGHTS SW1 SW2 SW3 SW4 TIME HIGH SEAL (SECONDS) WATER 10 OFF OFF OFF 20 ON OFF OFF OFF ON OFF OFF 30 OFF ON OFF 40 ON ON OFF 50 OFF ON ON 60 ON ON ON HIGH- TIME LIGHTS SW1 SW2 SW3 SW4 TIME HIGH SEAL (SECONDS) WATER.0 OFF OFF OFF 0.1 ON OFF OFF ON ON OFF OFF 0.2 OFF ON OFF 0.2 ON ON OFF 0.2 OFF ON ON 0.2 ON ON ON SEAL WATER TIMER LIGHTS SW1 SW2 SW3 SW4 TIME HIGH SEAL (SECONDS) WATER 5 OFF OFF OFF 10 ON OFF OFF OFF ON OFF ON 15 OFF ON OFF 20 ON ON OFF 25 OFF ON ON 30 ON ON ON
8 Page 8 TABLE 4, HIGH AND SEAL WATER F SWITCH CONNECTIONS LIGHTS SW1 SW2 SW3 SW4 SWITCH CONNECTIONS HIGH SEAL WATER HIGH - N/O - N/C OFF OFF OFF OFF OFF ON OFF SEAL WATER F - N/O HIGH - N/C - N/O ON OFF OFF SEAL WATER F - N/C TABLE 5 PRESS SW1 SW2 SW3 SW4 TEST BUTTON LOCAL ALARM TEST MODE FUNCTION FORCES ON HIGH RELAY AND LIGHT ON OFF OFF OFF REMOTE FORCES ON PRESURE RELAY AND LIGHT LOCAL AND REMOTE AT THE SAME TIME FORCES ON SEAL WATER RELAY AND LIGHT For information about Moyno Fluid Detection Control or progressing cavity pumps, write or call: Moyno, Inc. P.O. Box 960 Springfield, Ohio U.S.A. Telephone: UMOYNO (Municipal): Facsimile: (Municipal): Website: Robbins & Myers Limited School Lane Chandlers Ford, Hampshire SO53 3DG ENGLAND Telephone: / Facsimile: / Your Moyno Authorized Distributor is: Robbins & Myers Singapore Pte, Ltd. Singapore Branch No. 130 Gul Circle SINGAPORE Telephone: / & Facsimile: Moyno de México, S.A. de C.V. Av. Encarnación Ortiz No Col. Cosmopolita C.P Mexico, D.F. Telephone Facsimile MOYNO 1998 by Moyno, Inc. Moyno is a registered trademark of Moyno, Inc. Moyno, Inc. is a Unit of Robbins & Myers, Inc. Printed in U.S.A.
BUBBLER CONTROL SYSTEM
BUBBLER CONTROL SYSTEM Description: The HDBCS is a fully automatic bubbler system, which does liquid level measurements in water and wastewater applications. It is a dual air compressor system with, air
SPECIFICATIONS ATTENTION
VPS 504 S06 Installation Manual - P/N 80122 - Ed. 01/09 VPS 504 S06 and S05 Valve Proving System Installation Instructions VPS 1 6 Gases Natural gas, air and other inert gases. NOT suitable for butane
BUBBLER CONTROL SYSTEM
BUBBLER CONTROL SYSTEM Description: The LDBCS is a fully automatic bubbler system, which does liquid level measurements in water and wastewater applications. It is a dual air compressor system with, air
Valve Proving System VDK 200 A S06*
Valve Proving System VDK 200 A S06* Valve proving system with the following approvals. UL Recognized File # MH17004 CSA Certified File # 1637485 CSA Requirement No. 4-01 (USA) Technical Information Letter
Valve Proving System VDK 200 A S02
Valve Proving System VDK 200 A S02 Valve proving system with the following approvals. UL Recognized File # MH17004 CSA Certified File # 1637485 CSA Requirement No. 4-01 (USA) Technical Information Letter
CONDUCTIVITY POINT/S LEVEL SWITCH JAYCEEAQUA 4000 SERIES
I N S T R U C T I O N - M A N U A L CONDUCTIVITY POINT/S LEVEL SWITCH JAYCEEAQUA 4000 SERIES FUNCTION: Conductivity level limit switches are based on the principle of measuring level through the electrical
GAS FUEL VALVE FORM AGV5 OM 8-03
ALTRONIC AGV5 OPERATING MANUAL GAS FUEL VALVE FORM AGV5 OM 8-03 WARNING: DEVIATION FROM THESE INSTALLATION INSTRUCTIONS MAY LEAD TO IMPROPER ENGINE OPERATION WHICH COULD CAUSE PERSONAL INJURY TO OPERATORS
Differential pressure switch / Lube oil protection control MP 54 and MP 55
Data sheet Differential pressure switch / Lube oil protection control MP 54 and MP 55 MP 54 and MP 55 oil differential pressure switches are used as safety switches to protect refrigeration compressors
Inert Air (N2) Systems Manual
INSTRUCTION MANUAL Inert Air (N2) Systems Manual N2-MANUAL 2.10 READ AND UNDERSTAND THIS MANUAL PRIOR TO OPERATING OR SERVICING THIS PRODUCT. GENERAL INFORMATION Positive pressure nitrogen gas pressurizing
Aquavar SOLO 2 Frequently Asked Questions
Aquavar SOLO 2 Frequently Asked Questions How do I size the Aquavar SOLO 2 for the appropriate pump/motor combination? Can I use a 208 Volt motor? Can I run the Aquavar SOLO 2 up to 80HZ? What are the
O.K. Safety first CDN USA. Table of Contents. Approvals. Attention IFGC CSA UL ANSI NFPA
S06 & S02 Valve Proving System Installation Instructions USA CDN Table of Contents Table of Contents... Page 1 Approvals... Page 1 Attention... Page 1 Specification... Page 2 Mounting.... Page 3 Wiring...
SAPCON. User Manual. Capacitance Continuous Level Indicator. . Introduction. . General Description. . Principle of Operation. .
User Manual Capacitance Continuous Level Indicator Comprehensive User s Manual. Introduction. General Description. Principle of Operation. Specifications. Connection Diagrams. Quick Calibration Chart.
OC Panel High Limit Aquastat Kit, Manual Reset p/n
OC Panel High Limit Aquastat Kit, Manual Reset p/n 233202 Instruction Sheet APPLICATION The OC (Option Control) Panel High Limit Aquastat Kit provides electronic temperature sensing in a UL limit-rated
Stand-Alone Bubble Detection System
Instruction Sheet P/N Stand-Alone Bubble Detection System 1. Introduction The Bubble Detection system is designed to detect air-bubble induced gaps in a bead of material as it is being dispensed. When
700 SERIES BMS II BUBBLER MONITORING SYSTEM
1 700 SERIES BMS II BUBBLER MONITORING SYSTEM VISIT OUR WEBSITE AT SIGMACONTROLS.COM 700 SERIES BMS II MANUAL 062114 2 TABLE OF CONTENTS INTRODUCTION 3 Physical Specifications WIRING 5 PROGRAMMING & SETUP..
WATER MADE EASY MARINE ENERGY MUNICIPAL INDUSTRIAL
Capital Controls Series 71V3000 The Series 71V3000 electrically-heated vaporizer automatically vaporizes and superheats liquid chlorine, sulfur dioxide or ammonia at a rate controlled by the gas feed system.
TECHNICAL DATA. Q= Cv S
Page 1 of 13 1. DESCRIPTION The Viking 4 inch Model G-4000 Dry Valve Riser Assembly consists of a small profile, light weight, pilot operated valve that is used to separate the water supply from the dry
Differential pressure controls/ Lube oil protection controls MP 54 and MP 55 REFRIGERATION AND AIR CONDITIONING. Technical leafl et
Differential pressure controls/ Lube oil protection controls MP 54 and MP 55 REFRIGERATION AND AIR CONDITIONING Technical leafl et Contents Page Introduction... 3 Features... 3 Approvals... 3 Materials
UBEC 1AT. AUTO TANK Fill System Installation, Operation, & Setup Instructions
Document Number: XE-ATA5PM-R1A UBEC 1AT AUTO TANK Fill System 08899155 Installation, Operation, & Setup Instructions Rev170906-EB-FRC PHYSICAL: 1302 WEST BEARDSLEY AVE ELKHART, IN 46514 WWW.ELKHARTBRASS.COM
Model 4000 Pressure Controller
FEATURES Multiple Configurations The 4000 series pressure controller can be configured into either proportional only or proportional plus reset mode with a minimum of parts. Rugged Design Die cast aluminum
TECHNICAL DATA. Q = C v P S
Page 1 of 13 1. DESCRIPTION The Viking 6 Model G-6000 Dry Valve Riser Assembly consists of a small profile, light weight, pilot operated valve that is used to separate the water supply from the dry sprinkler
MEDICAL EQUIPMENT CATALOG
THE MOST TRUSTED MEDICAL EQUIPMENT IN NORTH AMERICA MEDICAL EQUIPMENT CATALOG Total Components Including Bulk Oxygen Supply, Back up and Delivery Equipment Designs for High Pressure, Liquid or Bulk Applications
Installation, operating and maintenance Instructions for Seemag bypass level indicator
Issue: S Date: 05-09-14 Type G35 General information The Seetru bypass magnetic level indicator, abbreviate SEEMAG, serves to show the filling level of fluids in tanks, basins, tubes etc. The Seemag operates
TECHNICAL DATA 3 MODEL G-3000 DRY VALVE RISER ASSEMBLY
Page 1 of 13 1. DESCRIPTION The Viking 3 Model G-3000 Dry Valve Riser Assembly is equipped with a small profile, light weight, pilot operated valve that is used to separate the water supply from the dry
Autocalibration Systems For In Situ Oxygen Analyzers
Product Data Sheet PDS 106-340AC SPS 4000, IMPS 4000, and MPS 3000 January, 1999 Autocalibration Systems For In Situ Oxygen Analyzers Cost-effective autocalibration systems for installations ranging from
TECHNICAL DATA. Q = C v P S
January 6, 2012 Preaction 333a 1. Description Viking supervised Surefire Preaction Systems Utilize the Viking G-3000P Valve. The small profile, lightweight, pilot-operated Viking G-3000P Valve comes complete
TECHNICAL DATA Q = C. v P S. 2 Model G-2000 Dry valve. Page 1 of 13
Page 1 of 13 1. Description The Viking 2 Model G-2000 Dry Valve Riser Assembly consists of a small profile, light weight, pilot operated valve that is used to separate the water supply from the dry sprinkler
Installation, Operation and Maintenance Instructions for Electronically Controlled Pressurisation Units
Installation, Operation and Maintenance Instructions for Electronically Controlled Pressurisation Units Models: EPS Single Pump EPT Twin Pump EPS-HP EPT-HP Single Pump High Pressure Twin Pump High Pressure
CDS-2000 CO 2 Sensor Verification, Calibration, and Troubleshooting Bulletin
Electronic Control Manual 216 Sensors and Stats Section S Technical Bulletin CDS-2000 Issue Date 0393 CDS-2000 CO 2 Sensor Verification, Calibration, and Troubleshooting Bulletin Introduction 3 Pre-Verification
CCT-7320/ROC-2313 Reverse Osmosis Controller
CCT-7320/ROC-2313 Reverse Osmosis Controller 1 General The instrument is a combined control instrument of a reverse osmosis controller and an on-line conductivity instrument. It can perform the operation
The Discussion of this exercise covers the following points:
Exercise 5-3 Wet Reference Leg EXERCISE OBJECTIVE Learn to measure the level in a vessel using a wet reference leg. DISCUSSION OUTLINE The Discussion of this exercise covers the following points: Measuring
ACV-10 Automatic Control Valve
ACV-10 Automatic Control Valve Installation, Operation & Maintenance General: The Archer Instruments ACV-10 is a precision automatic feed rate control valve for use in vacuum systems feeding Chlorine,
Reverse Osmosis System Installation Guide and Operation Manual.
Reverse Osmosis System Installation Guide and Operation Manual. Table of Contents 1 Introduction...2 2 Installation...3 2.1 Feed water connection...3 2.2 Permeate and concentrate plumbing...3 2.3 Electrical
EDUCATION DEPARTMENT ACCU-TEST
ABN 17 100 208 964 EDUCATION DEPARTMENT ACCU-TEST GAS SAFETY SHUT OFF SYSTEM Operating & Installation Manual Head Office (Melbourne) Sydney Brisbane (Distributor) 1/5 Samantha Court 2/14 Welder Road 17
LVU2800 Series. Ultrasonic Level Transmitter
LVU2800 Series Ultrasonic Level Transmitter 2 of 23 INTRODUCTION / TABLE OF CONTENTS Step One The LVU2800 Series is a general purpose ultrasonic level transmitter that provides a loop powered 4 20 ma output.
TECHNICAL DATA. Trimpac 257a. September 16, 2013
September 16, 2013 Trimpac 257a 1. DESCrIpTION DESCRIPTION The Viking Double SUREFIRE SIngle Interlock Preaction TRIMPAC Model D-2 and D-2B used with either a Model E or F Deluge Valve (A.1), a Viking
RAM Operation Manual. Worldwide Manufacturer of Gas Detection Solutions
RAM 4021 Operation Manual Worldwide Manufacturer of Gas Detection Solutions TABLE OF CONTENTS RAM 4021 For Your Safety... 2 Description.... 2 Setup Mode.... 2 Lights/Alarms.... 3 Operation.... 4 Calibration....
Preferred Instruments Danbury, CT USA
Tank Level Sensor Model TG-EL-WF-xx Installation & Operation Instructions SDI-TG-EL-WF March 6, 2006 Preferred Instruments Danbury, CT USA www.preferredinstruments.com CONTENTS Installation Pg. 2 Calibration
TECHNICAL DATA. Q = C v P S
January 6, 2012 Preaction 348a 1. Description Viking supervised Surefire Preaction Systems utilize the Viking G-6000P Valve. The small profile, lightweight, pilot operated Viking G-6000P Valve comes complete
TECHNICAL DATA. Q = C v P S
Preaction 346a 1. Description The 6 Model G-6000P Electric Release Preaction System Riser Assembly can be used as a Single Interlock Preaction System with Electric Release, or as a Double Interlock Preaction
RAM 4021-PR. Operation Manual. Worldwide Manufacturer of Gas Detection Solutions
RAM 4021-PR Operation Manual Worldwide Manufacturer of Gas Detection Solutions TABLE OF CONTENTS RAM 4021-PR For Your Safety... 2 Description.... 2 Setup Mode.... 2 Lights/Alarms.... 3 Operation.... 4
Universal Valve Company Inc
Universal Valve Company Inc 800-223-0741 www.universalvalve.com 1975-FA34 (Air Tower Troubleshooting Manual) Overview This manual has been arranged as a tool for diagnosing, and repairing Free Air Universal
Time-Delay Electropneumatic Applications
Exercise 3-4 EXERCISE OBJECTIVE & & & To introduce time delays; To describe the operation of a time-delay valve; To describe the operation of a time-delay relay. DISCUSSION Time-Delays Time delays are
RAM Operation Manual. Worldwide Manufacturer of Gas Detection Solutions
RAM 4021 Operation Manual Worldwide Manufacturer of Gas Detection Solutions TABLE OF CONTENTS RAM 4021 For Your Safety... 2 Description.... 2 Setup Mode.... 2 Lights/Alarms.... 3 Operation.... 4 Calibration....
Universal Valve Company Inc
1975-FA34 (Air Tower Troubleshooting Manual) Overview This manual has been arranged as a tool for diagnosing, and repairing Universal Air Towers Please read closely to identify the components that are
INSTALLATION. and INSTRUCTION MANUAL. for QUALITY AIR BREATHING SYSTEMS. Model 50 Systems Outfitted with ABM-725 Monitor C O M P A N Y
INSTALLATION and INSTRUCTION MANUAL for QUALITY AIR BREATHING SYSTEMS Model 50 Systems Outfitted with ABM-725 Monitor M A R T E C H S E R V I C E S C O M P A N Y OFFICE: (507) 843-4700 P.O. BOX 7079 Toll
RIX COMPRESSORS. MICROBOOST Owner s Manual CONFIGURATION A MB-115 MB-230. November 21, 2002 APPLICABILITY [ A]
RIX COMPRESSORS MICROBOOST Owner s Manual CONFIGURATION A MB-115 MB-230 November 21, 2002 APPLICABILITY [ A] INTRODUCTION Safety This electromechanical equipment is designed to produce high pressure gas.
ECONORESS ELECTRONIC EPS & EPT - ENHANCED PRESSURISATION SET INSTALLATION OPERATION & MAINTENANCE DOCUMENTATION
ECONORESS ELECTRONIC EPS & EPT - ENHANCED PRESSURISATION SET INSTALLATION OPERATION & MAINTENANCE DOCUMENTATION OCT2010 STOKVIS ENERGY SYSTEMS 96R WALTON ROAD EAST MOLESEY SURREY KT8 0DL TEL: 020 87833050
TECHNICAL DATA. Trimpac 244a. September 16, 2013
September 16, 2013 Trimpac 244a 1. DEsCrIpTION DESCRIPTION TRIMPAC Model B-1 and B-1B is a factory-assembled trim package with an electric release module in a metal enclosure. The standard trim normally
3 GALLON, OILLESS PANCAKE COMPRESSOR INSTRUCTIONS. Item #31289
3 GALLON, OILLESS PANCAKE COMPRESSOR INSTRUCTIONS Item #31289 The EASTWOOD 3 GALLON, OILLESS PANCAKE COMPRESSOR, with an Integral Air Regulator, efficiently supplies all compressed air requirements for
571 Series Medical TM. IntelliSwitch Electronic Switchover
ADI 9505-H 571 Series Medical TM IntelliSwitch Electronic Switchover INSTALLATION AND OPERATING INSTRUCTIONS Carefully Read These Instructions Before Operating Carefully Read These Controls Corporation
RAM 4021-DPX Operation Manual
RAM 4021-DPX Operation Manual Worldwide Manufacturer of Gas Detection Solutions TABLE OF CONTENTS ABL 4021-DPX / RAM 4021-DPX For Your Safety... 3 Description... 3 Setup Mode... 4 Lights/Alarms... 4 Operation...
TECHNICAL DATA. Q = C v P S
January 6, 2012 Preaction 347a 1. Description Viking supervised Double-Interlocked Electric/Pneumatic Release Preaction Systems utilize the Viking G-6000P Valve. The small profile, lightweight, pilot operated
Simple Set. Pressure Independent Control Valves 2 Way 1/2-2
The Bray Simple Set is a threaded pressure independent control (PIC) valve designed for a wide variety of hot water and chilled water control applications. The SS Series combines high rangeability control
Installation, Operation and Maintenance Instructions for Electronically Controlled Pressurisation Units Digital Range
Installation, Operation and Maintenance Instructions for Electronically Controlled Pressurisation Units Digital Range Models: DS 126 Single Pump / Single System DT 126 Twin Pump / Single System DS 160
TECHNICAL DATA. Trimpac 251a. Spetember 16, 2013
Spetember 16, 2013 Trimpac 251a 1. DEsCrIpTION DESCRIPTION TRIMPAC Model B-6 and B-6B is a factory assembled trim package for a double interlocked preaction system with an electric/pneu-lectric release
Blue River Technologies Port-A-Poly Mixer w/2.5 GPH LMI Pump And Secondary Water Dilution Line INSTALLATION AND OPERATION
Blue River Technologies Port-A-Poly Mixer w/2.5 GPH LMI Pump And Secondary Water Dilution Line INSTALLATION AND OPERATION Install your Blue River Technologies Port-A-Poly mixing system in a clean dry area.
Simple Set Max. Pressure Independent Control Valves 2 Way 2-1/ /09/18
The Bray Simple Set Max is a flanged pressure independent control (PIC) valve designed for a wide variety of hot water and chilled water control applications. The SSM Series combines high rangeability
INSTRUCTION MANUAL FOR MODEL 7360V VERTICAL CURING CHAMBER Revision E May
INSTRUCTION MANUAL FOR MODEL 7360V VERTICAL CURING CHAMBER Revision E May 2015 98-0520 S/N 2001 N. Indianwood Ave. Tulsa, Oklahoma 74012 U.S.A. TEL: (918) 250-7200 FAX: (918) 459-0165 E-mail: chandler.sales@ametek.com
Pocket Bellows Pumps. 180 Hines Ave. Bellville, OH PH: FAX:
Pumps models are ideal for low flow, low pressure metering applications. The pump is constructed entirely of plastic and utilizes GRI s time-proven bellows technology to provide an accurate chemically-resistant
COMPRESSED AIR SAVING PRODUCTS INDEX. Useful information AIR-SAVER G1 AIR-SAVER G2 LOCATOR. Condensate Management Specialist
INDEX Useful information AIR-SAVER G1 AIR-SAVER G2 LOCATOR COMPRESSED AIR SAVING PRODUCTS Condensate Management Specialist Information provided herewith is believed to be accurate and reliable. However,
NGP-250/500 Nitrogen Generator Quick Start Guide
NGP-250/500 Nitrogen Generator Quick Start Guide Version: A July 2013 Potter Electric Signal Company, LLC 5757 Phantom Dr., Suite 125 P. O. Box 42037 Hazelwood, MO 63042 Phone: (314) 595-6900 Document
TECHNICAL DATA. Trimpac 256a. October 31, 2013
October 31, 2013 Trimpac 256a 1. DESCRIPTION The Viking SUREFIRE SIngle Interlock Preaction TRIMPAC Model D-1 and D- 1B used with either a Model E or F Deluge Valve (A.1), a Viking Easy Riser check valve
Lesman Level Instrumentation LSB100/300 Series Basic Bubbler System
Lesman Level Instrumentation LSB100/300 Series Basic Bubbler System PART 1: GENERAL 1.1 SCOPE A. This section describes the specifications of a bubbler system. B. The following information shall be described
Liquid Level Controllers
Liquid Level Controllers ALL PUMPS LLC-2Y For both pump up and down control. Variable On/Off set points. NDP-15/20/25/32, DP-10/15 & *NDP-40/50/80 LLC-1 Pump up and down versions available. 6 to 12 differential
For Multi-Parameter Meters see mvx
Design Features VORTEX IN-LINE FLOW METERS For Multi-Parameter Meters see m Principles of Operation n No moving parts to wear or fail. n Electronics can be remotely mounted up to 30.5 m (0 ft). n No fluid
MP15 Jockey Pump Controller
Setup and Operating Instructions MP15 Jockey Pump Controller This manual provides general information, installation, operation, maintenance, and system setup information for Metron Model MP15 Jockey Pump
RCD - Ultra-Rugged Differential Pressure Flowmeter
0.15-1 to 85-600 GPM Liquids 2.5-25 to 300-1700 SCFM Gases 1/2 to 3 Line Sizes Bronze or 316-Ti Stainless Steel Mechanical Indicator, Digital Indicator, Transmitters and Switches Available Custom Calibrations
TH-1800-T TRX-700-CNG Converter
TH-1800-T TRX-700-CNG Converter low detector The CNG fuel gas flowmeter is so accurate as to meet a demand of measuring the CNG directly by making the most use of our well-established mini-thermal flowmeter
R E D I C O N T R O L S
R E D I C O N T R O L S Operation & Maintenance Manual Portable Service Purger for Low Pressure Chillers Model: PSP-LP-1B For Refrigerants R-11, R-113, R-114 & R-123 & Other Similar Refrigerants File Literature
D. ACCESSORIES ADAPTER KITS IMPELLER & SEAL INSTALLATION TOOLS CARRYING HANDLES & LIFT CORDS GALVANIC PROTECTION KITS MUSHROOM STRAINER
. ACCESSORIES AAPTER KITS IMPELLER & SEAL INSTALLATION TOOLS CARRYING HANLES & LIFT CORS GALVANIC PROTECTION KITS MUSHROOM STRAINER SLUGE STRAINERS NEMA 4 WATERTIGHT CONTROL & UAL LEVEL CONTROL (Replaces
P7911C PressureTrol Controller
P7911C PressureTrol Controller PRODUCT DATA FEATURES Use only with steam, air or noncombustible gases that do not corrode the pressure sensing element. Models available in 15, 150 and 300 psi (103, 1034
Digital Flow Switch. Series PFM7
Compatible with rgon (r), Carbon Dioxide (CO) and the Mixed Gas (r+co) Digital Flow witch eries PFM7 Flow adjustment valve Fluid r, CO r + CO RoH -color display ee abnormal values at a glance. llows flow
INSTRUCTION MANUAL STATION CONTROLLER SC100 MOTOR PROTECTION ELECTRONICS, INC.
INSTRUCTION MANUAL STATION CONTROLLER SC100 MOTOR PROTECTION ELECTRONICS, INC. 2464 Vulcan Road, Apopka, Florida 32703 Phone: (407) 299-3825 Fax: (407) 294-9435 Revision Date: 2-12-07 STATION CONTROLLER
Automatic Valve Proving Control
ISO 9001 Automatic Valve Proving Control 7 696 LDU11 UL recognized FM approved Features Performs leak test of the gas shut-off valves before start-up and/or immediately after burner shut-down No inlet
OPERATING INSTRUCTIONS MANUAL FOR QACV PNEUMATIC DOSING PUMP
This operating instructions contains safety information that if ignored can endanger life or result in serious injury. They are indicated by this icon. Use of this pump with radioactive chemicals is forbidden!
AIR COMPRESSOR OPERATING INSTRUCTION AND PARTS LIST
AIR COMPRESSOR OPERATING INSTRUCTION AND PARTS LIST OIL-LESS TYPE IMPORTANT: PLEASE READ CAREFULLY BEFORE STARTING OPERATIONS. THE CONTENTS ARE FOR GENERAL INFORMATION OF ALL THE SIMILAR MODELS. Record
Torque Tube TB300 Digital Transmitters
Page 1 of 7 7E.300-E Issue 4-2009 Description Series TB300 torque tube liquid level instruments utilize the buoyancy exerted on a displacer when immersed in a liquid. The buoyancy on the displacer is proportional
RAM 4021 Operation Manual
RAM 4021 Operation Manual Worldwide Manufacturer of Gas Detection Solutions TABLE OF CONTENTS RAM 4021 For your safety...3 Description...3 Set-up mode...4 Annunciator lights/alarms...4 Operation...5 Calibration...6
Pressure Measurement Single-range transmitters for general applications
Siemens AG 07 Overview Function U const. p U I EM Sensor Connection for auxiliary power supply Vent pipe with humidity filter Protective conductor connection/ Equipotential bonding Diaphragm The pressure
TECHNICAL DATA. Q = C v P S
January 6, 2012 Preaction 331a 1. Description Viking supervised Double-Interlocked Electric/Pneumatic Release Preaction Systems utilize the Viking G-3000P Valve. The small profile, lightweight, pilot-operated
Best Practice Guide, Servomex 2700
For full installations details refer to the. Best Practice Guide, Servomex 2700 Mounting: General Guidelines: Servomex 2700 Control Units and air supplies (utilities units) should, ideally, be mounted
TECHNICAL DATA OBSOLETE
April 9, 2009 Preaction 326a 1. DESCRIPTION Viking supervised Double-Interlocked Electric/Pneumatic Release Preaction Systems utilizing the Viking G-4000P Deluge Valve. The small profi le, lightweight,
INSTRUCTION MANUAL. Lesker Model KJL615TC-K Lesker Model KJL615TC-H. Digital Vacuum Gauge/Controller. KJL615TC K/H Ranges
INSTRUCTION MANUAL Lesker Model KJL615TC-K Lesker Model KJL615TC-H Digital Vacuum Gauge/Controller KJL615TC K/H Ranges 1 to 1999 millitorr 1 to 1990 microbar 1 to 199.9 Pascal Standard Features Selectable
RAM Operation Manual
RAM 4021-1 Operation Manual Worldwide Manufacturer of Gas Detection Solutions TABLE OF CONTENTS RAM 4021-1 For Your Safety... 2 Description... 2 Setup Mode... 3 Lights/Alarms... 3 Operation... 4 Calibration...
Model PSI Compressor with 3-Gallon Air Tank 12VDC
Model 6350 150 PSI Compressor with 3-Gallon Air Tank 12VDC IMPORTANT: It is essential that you and any other operator of this product read and understandd the contents of this manual before installing
For Multi-Parameter Meters see mvx
VORTEX IN-LINE FLOW METERS Design Features For Multi-Parameter Meters see mvx Principles of Operation VX No moving parts to wear or fail. Electronics can be remotely mounted up to 30.5 m (0 ft). No fluid
AIR SAVING PRODUCTS ADDING VALUE AIR-SAVER LOCATOR LOCATOR-EV
AIR SAVING PRODUCTS AIR-SAVER LOCATOR LOCATOR-EV ADDING VALUE REL LIABLE COMPRESSED AIR CONDENSATE MANAGEMENT AND ENERGY SAVING PRODUCTS Air saving products INDEX Chapter Content 1 Introduction to compressed
Locator Locator-D-Lux Air-Saver G1 Air-Saver G2
170663_air_saving_products 17-02-2011 16:42 Pagina 1 Locator Locator-D-Lux Air-Saver G1 Air-Saver G2 AIR SAVING PRODUCTS 170663_air_saving_products 17-02-2011 16:42 Pagina 2 170663_air_saving_products
DF-310E PROCESS ANALYSERS APPLICATIONS FEATURES
PROCESS ANALYSERS DF-310E The DF-310E is a Coulometric sensor based oxygen analyzer designed to measure trace and percent level oxygen in pure and multi-gas backgrounds for process and quality control
Workhorse-15 Oxygen Generator
11436 Sorrento Valley Road, San Diego CA 92121 USA 858-558-0202 Fax 858-558-1915 Workhorse-15 Oxygen Generator Model No. 5719, 5727, 5735 for Domestic and International Units Part number 1432 Revision
AUTOMATIC GAS MANIFOLDS
AUTOMATIC GAS MANIFOLDS Phoenix Pipeline Products Limited. Unit 8, McKenzie Industrial Park, Tel No.: 44 (0) 161 428 7200 Bird Hall Lane, Fax No.: 44 (0) 161 428 7010 Stockport, Email: info@p3-phoenix.com
TECHNICAL DATA MAINTENANCE AIR COMPRESSOR MODEL G-1
Dry 131h 1. DESCRIPTION The Viking Model G-1 Maintenance Air Compressor is an electric motor-driven, aircooled, single-stage, oil-less compressor. The unit is equipped with a check valve and provides a
CP3R Quick Start Manual
RUN MON PRM PU EXT NET RUN D700 3 200V RUN MON PRM PU EXT NET RUN D700 3 200V CP3R Quick Start Manual for Constant Pressure Applications This CP3R Drive has been factory pre-programmed for your specific
ANNEX AMENDMENTS TO THE INTERNATIONAL CODE FOR FIRE SAFETY SYSTEMS (FSS CODE) CHAPTER 15 INERT GAS SYSTEMS
Annex 3, page 2 ANNEX AMENDMENTS TO THE INTERNATIONAL CODE FOR FIRE SAFETY SYSTEMS (FSS CODE) CHAPTER 15 INERT GAS SYSTEMS The text of existing chapter 15 is replaced by the following: "1 Application This
QBS Electronic Pressure Regulator
INSTALLATION AND MAINTENANCE INSTRUCTIONS DESCRIPTION / IDENTIFICATION The QBS stainless steel series is an electronically controlled pressure regulator. The QBS controls the pressure on its output port
Operating instructions Electrical switching facility pco
Operating instructions Electrical switching facility pco from software version V1.33 on TABLE OF CONTENTS 1. Before you start... 4 1.1 Brief description... 4 1.2 Using this manual... 4 2. pco integrated
CPN1 Quick Start Manual
RUN MON PRM PU EXT NET RUN RUN MON PRM PU EXT NET RUN CPN1 Quick Start Manual for Constant Pressure Applications This CPN1 Drive has been factory pre-programmed for your specific pressure control application.
200 PSI FAST-FILL AIR SOURCE KIT
200 PSI FAST-FILL AIR SOURCE KIT 55% Duty Compressor on 2.0 Gallon Air Tank PART NO. 20007 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of
36C/36D HSI, DSI Proven Pilot Gas Valves INSTALLATION INSTRUCTIONS
36C/36D HSI, DSI Proven Pilot Gas Valves INSTALLATION INSTRUCTIONS Operator: Save these instructions for future use! FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR OPERATING