Division of Belarus Tractor International Quality Power Transmission Products 800-356-2336
Table of Contents Standard ANSI Single Strand: Page 3 Double Strand: Page 4 Triple Strand: Page 5 Quadruple Strand: Page 6 Heavy Series Single Strand: Page 7 Cottered Single Strand: Page 9 Double Strand: Page 10 Triple Strand: Page 11 Quadruple Strand: Page 12 Stainless Steel Single Strand: Page 13 Double Strand: Page 14 Extended Pitch: Page 15 Conveyor: Page 16 Nickel d Single Strand: Page 17 Extended Pitch Single Strand: Page 18 Conveyor Single Strand: Page 19 Oversized : Page 20 81X Lumber: Page 21 Hollow Single Strand: Page 22 Conveyor: Page 23 Metric (British Standard) Single Strand: Page 24 Double Strand: Page 25 Triple Strand: Page 26 Non-Standard Single Strand: Page 27 Agricultural Implement: Page 28 Attachment Pre-Made Attachment: Page 29 Finished Bore Sprockets (Type B/BS) #35 Sprocket: Page 30 #40Sprocket: Page 31 #50 Sprocket: Page 32 #60 Sprocket: Page 33 #80 Sprocket: Page 34 Sprockets (Type A) #40 Sprocket: Page 35 #50 Sprocket: Page 36 #60 Sprocket: Page 37 #80 Sprocket: Page 38 Double Couplers Couplers: Page 39 Weld On Sprockets & Hubs Sprockets: Page 40, 41 Hubs: Page 42 Idler Sprockets Idler Sprockets: Page 43 Keyed Shaft Keyed Shaft: Page 44 Solid Shaft Collars (Set Collars) Zinc d: Page 45 Stainless Steel: Page 45 Split Shaft Collars (Set Collars) Singe Split: Page 46 Double Split: Page 46 Solid Shaft Coupler Shaft Coupler: Page 47 L Jaw Couplings L Jaw Couplers: Page 48, 49 Pillow Block Bearing UCP Series: Page 50 Two Bolt Mounted Bearing UCFL Series: Page 51 SBLF Series:: Page 52 Four Bolt Mounted Bearing UCF Series: Page 53 SBF Series: Page 53 Take Up Mounted Bearing UCT Series: Page 55 2
Single Strand ANSI Pitch (P) Overall Tensile Width (b1) Width (L) (d2) Height (h2) Thickness (T) Strength (LBS) 25-1* 1/4 1/8 0.130 0.338 0.091 0.228 0.030 1,000 35-1* 3/8 3/16 0.200 0.514 0.141 0.346 0.050 2,400 40-1 1/2 5/16 0.312 0.703 0.156 0.469 0.060 3,900 41-1 1/2 1/4 0.306 0.573 0.141 0.390 0.050 2,833 50-1 5/8 3/8 0.400 0.868 0.200 0.585 0.080 6,600 60-1 3/4 1/2 0.469 1.065 0.234 0.709 0.094 9,300 80-1 1 5/8 0.625 1.348 0.312 0.949 0.125 15,600 100-1 1-1/4 3/4 0.750 1.677 0.375 1.188 0.156 24,500 120-1 1-1/2 1 0.875 2.118 0.437 1.425 0.187 35,100 140-1 1-3/4 1 1.000 2.307 0.500 1.663 0.219 47,600 160-1 2 1-1/4 1.125 2.691 0.562 1.889 0.250 62,700 180-1 2-1/4 1-13/32 1.406 3.075 0.687 2.047 0.281 76,800 200-1 2-1/2 1-1/2 1.562 3.299 0.781 2.375 0.312 97,000 240-1 3 1-7/8 1.875 4.070 0.937 2.791 0.375 139,900 *less chain = Bushing diameter (d1) 3
Double Strand ANSI Pitch (P) Overall Tensile Width (b1) Width (L) (d2) Height (h2) Thickness (T) Strength (LBS) 35-2* 3/8 3/16 0.200 0.918 0.141 0.346 0.050 4,400 40-2 1/2 5/16 0.312 1.280 0.156 0.469 0.060 8,000 50-2 5/8 3/8 0.400 1.571 0.200 0.585 0.080 13,000 60-2 3/4 1/2 0.469 1.961 0.234 0.709 0.094 18,400 80-2 1 5/8 0.625 2.468 0.312 0.949 0.125 31,800 100-2 1-1/4 3/4 0.750 3.031 0.375 1.188 0.156 49,300 120-2 1-1/2 1 0.875 3.791 0.437 1.425 0.187 70,700 140-2 1-3/4 1 1.000 4.079 0.500 1.663 0.219 96,100 160-2 2 1-1/4 1.125 4.889 0.562 1.889 0.250 126,400 200-2 2-1/2 1-1/2 1.562 5.980 0.781 2.375 0.312 190,000 240-2 3 1-7/8 1.875 7.486 0.937 2.791 0.375 282,200 *less chain = Bushing diameter (d1) 4
Triple Strand ANSI Pitch (P) Overall Tensile Width (b1) Width (L) (d2) Height (h2) Thickness (T) Strength (LBS) 40-3 1/2 5/16 0.312 1.839 0.156 0.469 0.060 11,200 50-3 5/8 3/8 0.400 2.280 0.200 0.585 0.080 17,400 60-3 3/4 1/2 0.469 2.858 0.234 0.709 0.094 25,000 80-3 1 5/8 0.625 3.610 0.312 0.949 0.125 44,600 100-3 1-1/4 3/4 0.750 4.510 0.375 1.188 0.156 69,600 120-3 1-1/2 1 0.875 5.740 0.437 1.425 0.187 98,200 140-3 1-3/4 1 1.000 6.160 0.500 1.663 0.219 133,300 160-3 2 1-1/4 1.125 7.330 0.562 1.889 0.250 175,400 200-3 2-1/2 1-1/2 1.562 9.010 0.781 2.375 0.312 273,300 240-3 3 1-7/8 1.875 10.990 0.937 2.791 0.375 456,420 5
Quadruple Strand ANSI Pitch (P) Overall Tensile Width (b1) Width (L) (d2) Height (h2) Thickness (T) Strength (LBS) 60-4 3/4 1/2 0.469 3.790 0.234 0.709 0.094 38,500 6
Heavy Series ANSI Pitch (P) Overall Tensile Width (b1) Width (L) (d2) Height (h2) Thickness (T) Strength (LBS) 50H 5/8 3/8 0.400 0.927 0.200 0.585 0.094 6,700 60H 3/4 1/2 0.469 1.210 0.234 0.709 0.125 9,600 80H 1 5/8 0.625 1.500 0.312 0.949 0.156 16,000 100H 1-1/4 3/4 0.750 1.800 0.375 1.188 0.187 25,200 120H 1-1/2 1 0.875 2.204 0.437 1.425 0.219 36,100 140H 1-3/4 1 1.000 2.441 0.500 1.663 0.250 48,800 160H 2 1-1/4 1.125 2.851 0.562 1.889 0.281 64,200 200H 2-1/2 1-1/2 1.562 3.681 0.781 2.375 0.375 97,000 7
Super Premium ANSI SP (Super Premium) is stronger than the standard or heavy ANSI roller chain. This is achieved by manufacturing the chain from a higher grade steel with more heat treatment. SP chain has a higher tensile strength of about 28% more over the standard ANSI roller chain. The SP chain is generally used in high shock load situations that offers greater fatigue resistance. Offset links are not available for the super premium roller chain. Pitch (P) Overall Tensile Width (b1) Width (L) (d2) Height (h2) Thickness (T) Strength (LBS) 80SP 1 5/8 0.625 1.500 0.312 0.949 0.156 19,000 100SP 1-1/4 3/4 0.750 1.590 0.375 1.185 0.157 28,500 120SP 1-1/2 1 0.875 1.980 0.437 1.425 0.189 41,800 140SP 1-3/4 1 1.000 2.140 0.500 1.661 0.220 55,000 8
Single Strand ANSI Cottered Pitch (P) Overall Tensile Width (b1) Width (L) (d2) Height (h2) Thickness (T) Strength (LBS) 80-1C 1 5/8 0.625 1.348 0.312 0.949 0.125 15,600 100-1C 1-1/4 3/4 0.750 1.677 0.375 1.188 0.156 24,500 120-1C 1-1/2 1 0.875 2.118 0.437 1.425 0.187 35,100 140-1C 1-3/4 1 1.000 2.307 0.500 1.663 0.219 47,600 160-1C 2 1-1/4 1.125 2.691 0.562 1.889 0.250 62,700 180-1C 2-1/4 1-13/32 1.406 3.075 0.687 2.047 0.281 76,800 200-1C 2-1/2 1-1/2 1.562 3.299 0.781 2.375 0.312 97,000 240-1C 3 1-7/8 1.875 4.070 0.937 2.791 0.375 139,900 9
Double Strand ANSI Cottered Pitch (P) Overall Tensile Width (b1) Width (L) (d2) Height (h2) Thickness (T) Strength (LBS) 80-2C 1 5/8 0.625 2.468 0.312 0.949 0.125 31,800 100-2C 1-1/4 3/4 0.750 3.031 0.375 1.188 0.156 49,300 120-2C 1-1/2 1 0.875 3.791 0.437 1.425 0.187 70,700 140-2C 1-3/4 1 1.000 4.079 0.500 1.663 0.219 96,100 160-2C 2 1-1/4 1.125 4.889 0.562 1.889 0.250 126,400 200-2C 2-1/2 1-1/2 1.562 5.980 0.781 2.375 0.312 190,000 240-2C 3 1-7/8 1.875 7.486 0.937 2.791 0.375 282,200 10
Triple Strand ANSI Cottered Pitch (P) Overall Tensile Width (b1) Width (L) (d2) Height (h2) Thickness (T) Strength (LBS) 80-3C 1 5/8 0.625 3.610 0.312 0.949 0.125 44,600 100-3C 1-1/4 3/4 0.750 4.510 0.375 1.188 0.156 69,600 120-3C 1-1/2 1 0.875 5.740 0.437 1.425 0.187 98,200 140-3C 1-3/4 1 1.000 6.160 0.500 1.663 0.219 133,300 160-3C 2 1-1/4 1.125 7.330 0.562 1.889 0.250 175,400 200-3C 2-1/2 1-1/2 1.562 9.010 0.781 2.375 0.312 273,300 240-3C 3 1-7/8 1.875 10.990 0.937 2.791 0.375 456,420 11
Quadruple Strand ANSI Cottered Pitch (P) Overall Tensile Width (b1) (d1) Width (L) (d2) Height (h2) Thickness (T) Strength (LBS) 60-4C 3/4 1/2 0.469 3.790 0.234 0.709 0.094 38,500 80-4C 1 5/8 0.625 5.150 0.312 0.949 0.125 72,000 100-4C 1-1/4 3/4 0.750 5.910 0.375 1.188 0.156 101,400 12
#304 Stainless Steel Single Strand ANSI Pitch (P) Overall Tensile Width (b1) Width (L) (d2) Height (h2) Thickness (T) Strength (LBS) 25SS-1* 1/4 1/8 0.130 0.338 0.091 0.228 0.030 480 35SS-1* 3/8 3/16 0.200 0.514 0.141 0.346 0.050 1,700 40SS-1 1/2 5/16 0.312 0.703 0.156 0.469 0.060 3,000 41SS-1 1/2 1/4 0.306 0.573 0.141 0.390 0.050 1,550 50SS-1 5/8 3/8 0.400 0.868 0.200 0.585 0.080 4,700 60SS-1 3/4 1/2 0.469 1.065 0.234 0.709 0.094 6,750 80SS-1 1 5/8 0.625 1.348 0.312 0.949 0.125 12,000 100SS-1 1-1/4 3/4 0.750 1.677 0.375 1.188 0.156 13,600 120SS-1 1-1/2 1 0.875 2.118 0.437 1.425 0.187 21,300 *less chain = Bushing diameter (d1) 13
#304 Stainless Steel Double Strand ANSI Pitch (P) Overall Tensile Width (b1) Width (L) (d2) Height (h2) Thickness (T) Strength (LBS) 35SS-2* 3/8 3/16 0.200 0.918 0.141 0.346 0.050 3,400 40SS-2 1/2 5/16 0.312 1.280 0.156 0.469 0.060 6,000 50SS-2 5/8 3/8 0.400 1.571 0.200 0.585 0.080 9,380 60SS-2 3/4 1/2 0.469 1.961 0.234 0.709 0.094 13,540 80SS-2 1 5/8 0.625 2.468 0.312 0.949 0.125 31,800 *less chain = Bushing diameter (d1) 14
#304 Stainless Steel Extended Pitch Pitch (P) Overall Tensile Width (b1) Width (L) (d2) Height (h2) Thickness (T) Strength (LBS) A2050SS 1-1/4 3/8 0.400 0.868 0.200 0.594 0.080 4,970 A2060SS 1-1/2 1/2 0.469 1.065 0.234 0.709 0.094 6,500 15
#304 Stainless Steel Conveyor Pitch (P) Overall Tensile Width (b1) (d1) Width (L) (d2) Height (h2) Thickness (T) Strength (LBS) C2040SS 1 5/16 0.312 0.703 0.156 0.469 0.060 2,760 C2050SS 1-1/4 3/8 0.400 0.868 0.200 0.590 0.080 4,970 C2060HSS 1-1/2 1/2 0.469 1.065 0.234 0.709 0.094 6,620 C2080HSS 2 5/8 0.625 1.531 0.312 0.949 0.156 10,590 16
Nickel d Single Strand ANSI Pitch (P) Overall Tensile Width (b1) Width (L) (d2) Height (h2) Thickness (T) Strength (LBS) 35NP-1* 3/8 3/16 0.200 0.514 0.141 0.346 0.050 2,400 40NP-1 1/2 5/16 0.312 0.703 0.156 0.469 0.060 3,900 41NP-1 1/2 1/4 0.306 0.573 0.141 0.390 0.050 2,833 50NP-1 5/8 3/8 0.400 0.868 0.200 0.585 0.080 6,600 60NP-1 3/4 1/2 0.469 1.065 0.234 0.709 0.094 9,300 80NP-1 1 5/8 0.625 1.348 0.312 0.949 0.125 15,600 100NP-1 1-1/4 3/4 0.750 1.677 0.375 1.188 0.156 24,500 *less chain = Bushing diameter (d1) 17
Extended Pitch Pitch (P) Overall Tensile Width (b1) (d1) Width (L) (d2) Height (h2) Thickness (T) Strength (LBS) A2040 1 5/16 0.312 0.703 0.156 0.469 0.060 3,700 A2050 1-1/4 3/8 0.400 0.868 0.200 0.594 0.080 6,300 A2060 1-1/2 1/2 0.469 1.065 0.234 0.709 0.094 8,200 18
Conveyor Pitch (P) Overall Tensile Width (b1) (d1) Width (L) (d2) Height (h2) Thickness (T) Strength (LBS) C2040 1 5/16 0.312 0.703 0.156 0.469 0.060 3,700 C2050 1-1/4 3/8 0.400 0.868 0.200 0.594 0.080 6,300 C2060H 1-1/2 1/2 0.469 1.065 0.234 0.709 0.094 9,300 C2080H 2 5/8 0.625 1.531 0.312 0.949 0.156 15,700 C2100H 2-1/2 3/4 0.750 1.807 0.375 1.188 0.187 27,200 C2120H 3 1 0.875 2.325 0.437 1.425 0.219 36,100 C2160H 4 1-1/4 1.125 2.875 0.563 1.901 0.281 69,300 19
Oversized Conveyor (Double Pitch) Pitch (P) Overall Tensile Width (b1) (d1) Width (L) (d2) Height (h2) Thickness (T) Strength (LBS) C2062H 1-1/2 1/2 0.875 1.065 0.234 0.709 0.094 9,300 C2082H 2 5/8 1.125 1.531 0.312 0.949 0.156 15,700 20
81X Lumber Conveyor Pitch (P) Overall Tensile Width (b1) (d1) Width (L) (d2) Height (h2) Thickness (T) Strength (LBS) 81X 2.609 1.062 0.905 2.062 0.437 1.122 0.156 28,900 81XH 2.609 1.062 0.905 2.531 0.437 1.122 0.220 39,500 81XHH 2.609 1.062 0.905 2.755 0.437 1.122 0.312 47,800 21
Single Strand Hollow Pitch (P) Overall Tensile Width (b1) (d1) Width (L) Outer (d2) Inner (d3) Height (h2) Thickness (T) Strength (LBS) 40-1HP 1/2 5/16 0.312 0.788 0.224 0.161 0.469 0.060 2,700 50-1HP 5/8 3/8 0.400 0.921 0.287 0.201 0.585 0.080 5,000 60-1HP 3/4 1/2 0.469 1.134 0.331 0.235 0.709 0.094 6,000 80-1HP 1 5/8 0.625 1.442 0.449 0.318 0.949 0.125 11,600 22
Conveyor Hollow Pitch (P) Overall Tensile Width (b1) (d1) Width (L) Outer (d2) Inner (d3) Height (h2) Thickness (T) Strength (LBS) C2040-1HP 1 5/16 0.312 0.676 0.224 0.161 0.469 0.060 2,800 C2050-1HP 1-1/4 3/8 0.400 0.830 0.287 0.201 0.585 0.080 5,100 C2060-1HP 1-1/2 1/2 0.469 1.056 0.331 0.235 0.709 0.094 6,000 C2080-1HP 2 5/8 0.625 1.348 0.449 0.318 0.949 0.125 11,600 23
Metric (British Standard) Pitch (P) Overall Tensile Width (b1) (d1) Width (L) (d2) Height (h2) Thickness (T) Strength (LBS) 06B 3/8 0.225 0.250 0.531 0.130 0.335 0.050 2,300 08B 1/2 0.305 0.335 0.669 0.175 0.472 0.060 4,000 10B 5/8 0.380 0.400 0.772 0.200 0.579 0.065 5,600 12B 3/4 0.460 0.475 0.894 0.225 0.637 0.070 7,200 16B 1 0.670 0.625 1.421 0.326 0.827 0.156 15,000 20B 1-1/4 0.770 0.750 1.701 0.401 1.039 0.177 23,800 24B 1-1/2 1.000 1.000 2.102 0.576 1.315 0.238 40,000 32B 2 1.220 1.150 2.654 0..701 1.661 0.276 62,300 24
Double Strand Metric (British Standard) Pitch (P) Overall Tensile Width (b1) (d1) Width (L) (d2) Height (h2) Thickness (T) Strength (LBS) 06B-2 3/8 0.225 0.250 0941 0.130 0.335 0.050 4,200 08B-2 1/2 0.305 0.335 1.248 0.175 0.465 0.060 8,700 10B-2 5/8 0.380 0.400 1.493 0.200 0.579 0.065 12,600 12B-2 3/4 0.460 0.475 1.706 0.225 0.637 0.070 14,800 16B-2 1 0.670 0.625 2.744 0.326 0.827 0.156 29,900 25
Triple Strand Metric (British Standard) Pitch (P) Overall Tensile Width (b1) (d1) Width (L) (d2) Height (h2) Thickness (T) Strength (LBS) 06B-3 3/8 0.225 0.250 1.360 0.130 0.335 0.050 6,700 08B-3 1/2 0.305 0.335 1.815 0.175 0.465 0.060 13,000 10B-3 5/8 0.380 0.400 2.130 0.200 0.579 0.065 19,000 12B-3 3/4 0.460 0.475 2.484 0.225 0.637 0.070 22,800 26
Non-Standard Pitch (P) Overall Tensile Width (b1) (d1) Width (L) (d2) Height (h2) Thickness (T) Strength (LBS) 410 (43)(65) 1/2 1/8 0.305 0.408 0.142 0.390 0.040 1,700 415 (42) 1/2 3/16 0.305 0.468 0.142 0.390 0.040 1,700 420 1/2 1/4 0.306 0.644 0.156 0.469 0.060 4,000 520 5/8 1/4 0.400 0.742 0.200 0.594 0.080 6,600 27
Implement (Agricultural) Pitch (P) Overall Tensile Width (b1) (d1) Width (L) (d2) Height (h2) Thickness (T) Strength (LBS) CA550 1.630 0.780 0.656 1.504 0.281 0.787 0.106 12,500 CA557 1.630 0.797 0.700 1.600 0.315 0.909 0.125 16,700 CA620 1.650 0.965 0.705 1.780 0.285 0.795 0.128 12,300 28
Attachment A1 Attachment K1 Attachment SK1 Attachment SA1 Attachment We offer many more style of attachment roller chains. Custom made-to-order roller chain assemblies are available. Send us your inquiry with drawing for a custom quote. 29
#35 Finished Bore Sprockets Type B (BS) Heat treated teeth Keyway is in center line of a tooth Black Oxide Finish 2 Set Screws Sprocket Thickness (B1): 0.168 Each sprocket size is available in several bore sizes Sprocket Outside Length Hub Size of Teeth Thru Bore (de) (A) (dm) 35B10 10 1.379 3/4 1 35B11 11 1.502 3/4 1-1/16 35B12 12 1.625 3/4 1-1/4 35B13 13 1.746 3/4 1-1/8 35B14 14 1.868 3/4 1-1/4 35B15 15 1.989 3/4 1-1/2 35B16 16 2.110 3/4 1-5/8 35B17 17 2.231 3/4 1-5/8 35B18 18 2.352 3/4 1-3/4 35B19 19 2.472 3/4 1-13/16 35B20 20 2.593 3/4 1-15/16 35B21 21 2.713 3/4 2 35B24 24 3.073 7/8 2 35B25 25 3.193 7/8 2 35B28 28 3.553 7/8 2 30
#40 Finished Bore Sprockets Type B (BS) Heat treated teeth Keyway is in center line of a tooth Black Oxide Finish 2 Set Screws Sprocket Thickness (B1): 0.284 Each sprocket size is available in several bore sizes Sprocket Outside Length Hub Sprocket Outside Length Hub Size of Teeth (de) Thru Bore (A) (dm) Size of Teeth (de) Thru Bore (A) (dm) 40B9 9 1.674 7/8 1-1/8 40B10 10 1.839 7/8 1-1/4 40B11 11 2.003 7/8 1-7/16 40B12 12 2.166 7/8 1-9/16 40B13 13 2.329 7/8 1-9/16 40B14 14 2.491 7/8 1-11/16 40B15 15 2.653 7/8 1-13/16 40B16 16 2.814 7/8 2 40B17 17 2.975 1 2-1/8 40B18 18 3.136 1 2-5/16 40B19 19 3.297 1 2-1/2 40B20 20 3.457 1 2-5/8 40B21 21 3.618 1 2-3/4 40B22 22 3.778 1 2-7/8 40B23 23 3.938 1 3 40B24 24 4.098 1 3-1/4 40B25 25 4.258 1 3-1/4 40B26 26 4.418 1 3-1/4 40B27 27 4.587 1 3-1/4 40B28 28 4.738 1 3-1/4 40B29 29 4.898 1 3-1/4 40B30 30 5.057 1 3-1/4 40B32 32 5.377 1 3-1/4 40B35 35 5.856 1 3-1/4 40B36 36 6.015 1 3-1/4 40B40 40 6.653 1-1/8 3-1/2 40B45 45 7.451 1-1/8 3-1/2 40B60 60 9.841 1-1/8 3-1/2 31
#50 Finished Bore Sprockets Type B (BS) Heat treated teeth Keyway is in center line of a tooth Black Oxide Finish 2 Set Screws Sprocket Thickness (B1): 0.343 Each sprocket size is available in several bore sizes Sprocket Outside Length Hub Sprocket Outside Length Hub Size of Teeth (de) Thru Bore (A) (dm) Size of Teeth (de) Thru Bore (A) (dm) 50B9 9 2.092 1 1-3/8* 50B10 10 2.299 1 1-9/16* 50B11 11 2.504 1 1-3/4* 50B12 12 2.708 1 1-63/64* 50B13 13 2.911 1 1-7/8* 50B14 14 3.114 1 2-1/8 50B15 15 3.316 1 2-3/8 50B16 16 3.517 1 2-1/2 50B17 17 3.719 1 2-11/16 50B18 18 3.919 1 2-7/8 50B19 19 4.121 1 3 50B23 23 4.922 1 3 50B24 24 5.123 1-1/4 3 50B25 25 5.323 1-1/4 3 50B26 26 5.532 1-1/4 3 50B27 27 5.723 1-1/4 3 50B28 28 5.922 1-1/4 3 50B29 29 6.122 1-1/4 3 50B30 30 6.321 1-1/4 3-1/4 50B32 32 6.721 1-1/4 3-1/4 50B36 36 7.519 1-1/4 3-1/4 50B40 40 8.316 1-1/4 3-1/4 50B20 20 4.321 1 3 50B21 21 4.521 1 3 50B22 22 4.722 1 3 *Has recessed groove for chain clearance 32
#60 Finished Bore Sprockets Type B (BS) Heat treated teeth Keyway is in center line of a tooth Black Oxide Finish 2 Set Screws Sprocket Thickness (B1): 0.459 Each sprocket size is available in several bore sizes Sprocket Outside Length Hub Sprocket Outside Length Hub Size of Teeth (de) Thru Bore (A) (dm) Size of Teeth (de) Thru Bore (A) (dm) 60B9 9 2.510 1-1/4 1-11/16* 60B10 10 2.759 1-1/4 1-15/16* 60B11 11 3.005 1-1/4 2-1/16* 60B12 12 3.249 1-1/4 2-3/8* 60B13 13 3.493 1-1/4 2-1/4 60B14 14 3.736 1-1/4 2-9/16 60B15 15 3.979 1-1/4 2-5/8 60B16 16 4.220 1-1/4 3-1/16 60B17 17 4.463 1-1/4 3-1/4 60B18 18 4.703 1-1/4 3-1/2 60B23 23 5.906 1-1/4 4 60B24 24 6.147 1-1/4 4 60B25 25 6.387 1-1/4 4 60B26 26 6.627 1-1/4 4 60B27 27 6.867 1-1/4 4 60B28 28 7.106 1-1/4 4 60B30 30 7.586 1-1/4 4 60B32 32 8.065 1-1/4 4 60B35 35 8.783 1-1/4 4 60B36 36 9.023 1-1/4 4 60B19 19 4.945 1-1/4 3-1/2 60B20 20 5.186 1-1/4 3-7/8 60B21 21 5.426 1-1/4 4 60B22 22 5.666 1-1/4 4 *Has recessed groove for chain clearance 33
#80 Finished Bore Sprockets Type B (BS) Heat treated teeth Keyway is in center line of a tooth Black Oxide Finish 2 Set Screws Sprocket Thickness (B1): 0.579 Each sprocket size is available in several bore sizes Sprocket Outside Length Hub Sprocket Outside Length Hub Size of Teeth (de) Thru Bore (A) (dm) Size of Teeth (de) Thru Bore (A) (dm) 80B9 9 3.347 1-5/8 2-1/4* 80B24 24 8.196 1-3/4 4-1/4 80B10 10 3.678 1-5/8 2-9/16* 80B11 11 4.000 1-5/8 2-13/16* 80B12 12 4.332 1-5/8 3-1/8* 80B13 13 4.657 1-1/2 3 80B14 14 4.982 1-1/2 3-1/4 80B15 15 5.305 1-1/2 3-13/16 80B16 16 5.627 1-1/2 4 80B17 17 5.950 1-1/2 4-1/4 80B18 18 6.271 1-1/2 4-1/4 80B19 19 6.593 1-1/2 4-1/4 80B20 20 6.914 1-1/2 4-1/4 80B22 22 7.555 1-3/4 4-1/4 80B23 23 7.876 1-3/4 4-1/4 *Has recessed groove for chain clearance 34
#40 Type A Sprocket Heat treated teeth Black Oxide Finish Sprocket Thickness (B1): 0.284 Sprocket Outside Bore Sprocket Outside Bore Size of Teeth (D1) Size of Teeth (D1) (de) (de) 40A10 10 1.839 1/2 40A11 11 2.003 1/2 40A12 12 2.166 1/2 40A13 13 2.329 1/2 40A14 14 2.491 1/2 40A15 15 2.653 5/8 40A16 16 2.814 5/8 40A17 17 2.975 5/8 40A18 18 3.136 5/8 40A19 19 3.297 5/8 40A20 20 3.457 5/8 40A21 21 3.618 5/8 40A22 22 3.778 5/8 40A24 24 4.098 5/8 40A25 25 4.258 5/8 40A26 26 4.418 5/8 40A27 27 4.587 5/8 40A28 28 4.738 5/8 40A30 30 5.057 5/8 40A32 32 5.377 5/8 40A35 35 5.856 5/8 40A36 36 6.015 5/8 40A40 40 6.653 5/8 40A45 45 7.451 3/4 40A48 48 7.929 3/4 40A23 23 3.938 5/8 35
#50 Type A Sprocket Heat treated teeth Black Oxide Finish Sprocket Thickness (B1): 0.343 Sprocket Outside Bore Sprocket Outside Bore Size of Teeth (D1) Size of Teeth (D1) (de) (de) 50A10 10 2.299 1/2 50A11 11 2.504 1/2 50A12 12 2.708 5/8 50A13 13 2.911 5/8 50A14 14 3.114 5/8 50A15 15 3.316 5/8 50A16 16 3.517 5/8 50A17 17 3.719 5/8 50A18 18 3.919 5/8 50A19 19 4.121 5/8 50A20 20 4.321 3/4 50A24 24 5.123 3/4 50A25 25 5.323 3/4 50A26 26 5.532 3/4 50A27 27 5.723 3/4 50A28 28 5.922 3/4 50A30 30 6.321 3/4 50A32 32 6.721 3/4 50A34 34 7.120 3/4 50A36 36 7.519 3/4 50A40 40 8.316 3/4 50A21 21 4.521 3/4 50A22 22 4.722 3/4 50A23 23 4.922 3/4 36
#60 Type A Sprocket Black Oxide Finish Sprocket Thickness (B1): 0.459 Sprocket Outside Bore Sprocket Outside Bore Size of Teeth (D1) Size of Teeth (D1) (de) (de) 60A9 9 2.510 1/2 60A10 10 2.759 3/4 60A11 11 3.005 3/4 60A12 12 3.249 3/4 60A13 13 3.493 3/4 60A14 14 3.736 3/4 60A15 15 3.979 3/4 60A16 16 4.220 3/4 60A17 17 4.463 3/4 60A18 18 4.703 3/4 60A19 19 4.945 3/4 60A20 20 5.186 3/4 60A24 24 6.147 3/4 60A25 25 6.387 3/4 60A26 26 6.627 3/4 60A27 27 6.867 3/4 60A28 28 7.106 3/4 60A30 30 7.586 3/4 60A32 32 8.065 3/4 60A34 34 8.544 1 60A35 35 8.783 1 60A36 36 9.023 1 60A40 40 9.980 1 60A21 21 5.426 3/4 60A22 22 5.666 3/4 60A23 23 5.906 3/4 37
#80 Type A Sprocket Black Oxide Finish Sprocket Thickness (B1): 0.575 Sprocket Outside Bore Sprocket Outside Bore Size of Teeth (D1) Size of Teeth (D1) (de) (de) 80A9 9 3.347 15/16 80A10 10 3.678 15/16 80A11 11 4.000 15/16 80A12 12 4.332 15/16 80A13 13 4.657 15/16 80A14 14 4.982 15/16 80A15 15 5.305 15/16 80A16 16 5.627 15/16 80A17 17 5.950 15/16 80A18 18 6.271 15/16 80A19 19 6.593 15/16 80A20 20 6.914 15/16 80A24 24 8.196 15/16 80A25 25 8.516 15/16 80A26 26 8.836 13/16 80A27 27 9.156 13/16 80A28 28 9.475 13/16 80A30 30 10.114 13/16 80A32 32 10.753 13/16 80A34 34 13/16 80A35 35 11.711 13/16 80A36 36 12.030 13/16 80A40 40 13.306 13/16 80A21 21 7.235 15/16 80A22 22 7.555 15/16 80A23 23 7.875 15/16 38
Double Couplers Heat Treated Teeth Not to exceed 5000 FPM rim speed Each coupling half is available in several bore sizes Coupling Size Outside Outside Hub Length Overall of Teeth w/o w/ Thru Bore (LTB) Length Thru Bore DC4012 40 12 2 2-13/32 1-13/32 1-1/8 2-17/32 DC4016 40 16 2-5/8 3-1/32 1-13/32 1-1/8 2-17/32 DC5016 50 16 3-1/4 3-25/32 2-1/2 1-7/16 3-1/4 DC5018 50 18 3-3/4 4-3/16 2-31/32 1-11/16 3-3/4 DC6018 60 18 4-3/8 5 3-1/2 1-7/8 4-3/16 DC6020 60 20 4-7/8 5-1/2 3-7/8 2 5-21/64 39
Weld On Sprockets We recommend using Low Hydrogen Electrodes for welding sprockets and hubs together. Black Oxide finish Sprocket Size Outside Bore Sprocket Size Outside Bore Size of Teeth (D1) Size of Teeth (D1) (de) (de) 4040X 40 40 6.653 2 4042X 40 42 6.972 2 4048X 40 48 7.927 2 4054X 40 54 8.885 2 4060X 40 60 9.841 2 4070X 40 70 11.433 2 4072X 40 72 11.752 2 4080X 40 80 13.026 2 4084X 40 84 13.663 2 4096X 40 96 15.573 2 40112X 40 112 18.12 2 5040X 50 40 8.316 2 5042X 50 42 8.715 2 5044X 50 44 9.114 2 5045X 50 45 9.313 2 5048X 50 48 9.911 2 5050X 50 50 10.309 2 5052X 50 52 10.708 2 5054X 50 54 11.106 2 5060X 50 60 12.301 2 5065X 50 65 13.296 2 5070X 50 70 14.292 2 5072X 50 72 14.690 2 5080X 50 80 16.283 2 5084X 50 84 17.079 2 5096X 50 96 19.467 2 50112X 50 112 22.651 2 6038X 60 38 9.501 2 6040X 60 40 9.980 2 6048X 60 48 11.893 2 6050X 60 50 12.371 2 6054X 60 54 13.327 2 6060X 60 60 14.761 2 6072X 60 72 17.628 2 More sizes continued on the next page... 40
Weld On Sprockets We recommend using Low Hydrogen Electrodes for welding sprockets and hubs together. Black Oxide finish Sprocket Size Outside Bore Sprocket Size Outside Bore Size of Teeth (D1) Size of Teeth (D1) (de) (de) 6080X 60 80 19.539 2 6096X 60 96 23.360 2 60112X 60 112 27.181 2 8024X 80 24 8.196 2 8025X 80 25 8.516 2 8048X 80 48 15.857 2 10010X 100 10 4.598 2 10011X 100 11 5.008 2 10012X 100 12 5.415 2 10013X 100 13 5.821 2 8026X 80 26 8.836 2 8027X 80 27 9.156 2 8028X 80 28 9.475 2 8029X 80 29 9.795 2 8030X 80 30 10.114 2 8032X 80 32 10.753 2 8033X 80 33 11.072 2 8034X 80 34 11.392 2 8035X 80 35 11.711 2 8036X 80 36 12.030 2 8040X 80 40 13.306 2 8045X 80 45 14.901 2 41
Weld On Hub We recommend using Low Hydrogen Electrodes for welding sprockets and hubs together. Black Oxide finish Hub Size Bore Outside Flange Length Thru Bore HUBX-IDLER 5/8* 2-1/2 2 11/16 HUBX1/2 1/2 2-1/2 2 1.435 HUBX5/8 5/8 2-1/2 2 1.435 HUBX11/16 11/16 2-1/2 2 1.435 HUBX3/4 3/4 2-1/2 2 1.435 HUBX13/16 13/16 2-1/2 2 1.435 HUX7/8 7/8 2-1/2 2 1.435 HUBX15/16 15/16 2-1/2 2 1.435 HUBX1 1 2-1/2 2 1.435 HUBX1-1/16 1-1/16 2-1/2 2 1.435 HUBX1-1/8 1-1/8 2-1/2 2 1.435 HUBX1-3/16 1-3/16 2-1/2 2 1.435 HUBX1-1/4 1-1/4 2-1/2 2 1.435 HUBX1-5/16 1-5/16 2-1/2 2 1.435 HUBX1-3/8 1-3/8 2-1/2 2 1.435 HUBX1-7/16 1-7/16 2-1/2 2 1.435 HUBX1-1/2 1-1/2 2-1/2 2 1.435 * Comes with 1/2 reducer bushing 42
Idler Sprockets Sealed ball bearing Ball bearing has a wide inner ring Max RPM: 1000 Hardened teeth May not depict the actual style of Idler sprocket. Sprocket Bore Outside Length Sprocket Bore Outside Length Size Size of Teeth Thru Bore Size Size of Teeth Thru Bore (de) (de) 35BB18-1/2 35 18 1/2 2.352 11/16 35BB18-5/8 35 18 5/8 2.352 11/16 40BB17-1/2 40 17 1/2 2.975 11/16 80BB11-3/4 80 11 3/4 4.000 13/16 80BB12-3/4 80 12 3/4 4.332 13/16 100BB10-1 100 10 1 4.598 7/8 40BB17-5/8 40 17 5/8 2.975 11/16 50BB13-1/2 50 13 1/2 2.911 11/16 50BB13-5/8 50 13 5/8 2.911 11/16 50BB15-1/2 50 15 1/2 3.316 11/16 50BB15-5/8 50 15 5/8 3.316 11/16 50BB17-1/2 50 17 1/2 3.719 11/16 50BB17-5/8 50 17 5/8 3.719 11/16 60BB11-1/2 60 11 1/2 3.005 11/16 60BB11-5/8 60 11 5/8 3.005 11/16 60BB13-1/2 60 13 1/2 3.493 11/16 60BB13-5/8 60 13 5/8 3.493 11/16 60BB15-1/2 60 15 1/2 3.979 11/16 60BB15-5/8 60 15 5/8 3.979 11/16 43
Keyed Shafting Material: C1018 cold drawn & 303 Stainless Steel Straightness tolerance: 0.012" per foot (Straightness not guaranteed) Stocked in 3 foot sections. Available in 6 foot section by quote. C1018CD 303 Keyway Length (Feet) KS1/2-3FT KS1/2SS-3FT 1/2 1/8 X 1/16 3 KS5/8-3FT KS5/8SS-3FT 5/8 3/16 X 3/32 3 KS11/16-3FT KS11/16SS-3FT 11/16 3/16 X 3/32 3 KS3/4-3FT KS3/4SS-3FT 3/4 3/16 X 3/32 3 KS13/16-3FT KS13/16SS-3FT 13/16 3/16 X 3/32 3 KS7/8-3FT KS7/8SS-3FT 7/8 3/16 X 3/32 3 KS1-3FT KS1SS-3FT 1 1/4 X 1/8 3 KS1-1/8-3FT KS1-1/8SS-3FT 1-1/8 1/4 X 1/8 3 KS1-3/16-3FT KS1-3/16SS-3FT 1-3/16 1/4 X 1/8 3 KS1-1/4-3FT KS1-1/4SS-3FT 1-1/4 1/4 X 1/8 & 5/16 X 5/32 3 KS1-5/16-3FT KS1-5/16SS-3FT 1-5/16 5/16 X 5/32 3 KS1-3/8-3FT KS1-3/8SS-3FT 1-3/8 5/16 X 5/32 3 KS1-7/16-3FT KS1-7/16SS-3FT 1-7/16 3/8 X 3/16 3 KS1-1/2-3FT KS1-1/2SS-3FT 1-1/2 3/8 X 3/16 3 KS1-5/8-3FT KS1-5/8SS-3FT 1-5/8 3/8 X 3/16 3 KS1-3/4-3FT KS1-3/4SS-3FT 1-3/4 3/8 X 3/16 3 KS1-15/16-3FT KS1-15/16SS-3FT 1-15/16 1/2 X 1/4 3 KS2-3FT KS2SS-3FT 2 1/2 X 1/4 3 44
Solid Shaft Collars Solid Shaft collars with set screw Metric, threaded, aluminum and black oxide available by quotation. Zinc d 304 Stainless Bore Outside Width Set Screw SC1/4 SSSC1/4 1/4 1/2 9/32 10-32 SC5/16-5/16 5/8 5/16 10-32 SC3/8 SSSC3/8 3/8 3/4 3/8 1/4-20 SC7/16-7/16 7/8 7/16 1/4-20 SC1/2 SSSC1/2 1/2 1 7/16 1/4-20 SC9/16-9/16 1 7/16 1/4-20 SC5/8 SSSC5/8 5/8 1-1/8 1/2 5/16-18 SC11/16-11/16 1-1/4 9/16 5/16-18 SC3/4 SSSC3/4 3/4 1-1/4 9/16 5/16-18 SC13/16-13/16 1-5/16 9/16 5/16-18 SC7/8 SSSC7/8 7/8 1-1/2 9/16 5/16-18 SC15/16-15/16 1-5/8 5/8 5/16-18 SC1 SSSC1 1 1-5/8 5/8 5/16-18 SC1-1/16-1-1/16 1-3/4 5/8 5/16-18 SC1-1/8-1-1/8 1-3/4 5/8 5/16-18 SC1-3/16 SSSC1-3/16 1-3/16 2 11/16 3/8-16 SC1-1/4 SSSC1-1/4 1-1/4 2 11/16 3/8-16 SC1-5/16-1-5/16 2-1/8 11/16 3/8-16 SC1-3/8 SSSC1-3/8 1-3/8 2-1/8 3/4 3/8-16 SC1-7/16 SSSC1-7/16 1-7/16 2-1/4 3/4 3/8-16 SC1-1/2 SSSC1-1/2 1-1/2 2-1/4 3/4 3/8-16 SC1-5/8-1-5/8 2-1/2 13/16 3/8-16 SC1-3/4 SSSC1-3/4 1-3/4 2-3/4 7/8 1/2-13 SC1-7/8-1-7/8 2-3/4 7/8 1/2-13 SC1-15/16-1-15/16 3 7/8 1/2-13 SC2 SSSC2 2 3 7/8 1/2-13 SC2-1/4-2-1/4 3-1/4 15/16 1/2-13 SC2-1/2-2-1/2 3-1/4 1 1/2-13 SC2-3/4-2-3/4 4 1-1/8 1/2-13 SC3-3 4-1/4 1-1/8 1/2-13 45
Single & Double Split Shaft Collars Split set collars finished with Black Oxide Metric, threaded and aluminum shaft collars are available by quotation. Single Split Double Split Bore Outside Width Socket Heads SSC1/4 DSSC1/4 1/4 11/16 5/16 4-40 SSC3/8 DSSC3/8 3/8 7/8 11/32 6-32 SSC1/2 DSSC1/2 1/2 1-1/8 13/32 8-32 SSC5/8 DSSC5/8 5/8 1-15/16 7/16 10-32 SSC3/4 DSSC3/4 3/4 1-1/2 1/2 1/4-28 SSC7/8 DSSC7/8 7/8 1-5/8 1/2 1/4-28 SSC1 DSSC1 1 1-3/4 1/2 1/4-28 - DSSC1-1/8 1-1/8 1-7/8 1/2 1/4-28 SSC1-3/16 DSSC1-3/16 1-3/16 2-1/16 1/2 1/4-28 SSC1-1/4 DSSC1-1/4 1-1/4 2-1/16 1/2 1/4-28 SSC1-3/8 DSSC1-3/8 1-3/8 2-1/4 9/16 1/4-28 SSC1-7/16 DSSC1-7/16 1-7/16 2-1/4 9/16 1/4-28 SSC1-1/2 DSSC1-1/2 1-1/2 2-3/8 9/16 1/4-28 SSC1-3/4 DSSC1-3/4 1-3/4 2-3/4 11/16 5/16-24 SSC2 DSSC2 2 3 11/16 5/16-24 46
Shaft Couplers Solid shaft coupler with keyway and 2 setscrews Black Oxide finish Coupler Bore Outside Overall Length Keyway Set Screw SHC1/2 1/2 1-1/4 2 1/8 X 1/16 1/4-20 SHC5/8 5/8 1-1/2 2-1/2 3/16 X 3/32 1/4-20 SHC3/4 3/4 1-5/8 3 3/16 X 3/32 1/4-20 SHC7/8 7/8 1-3/4 3 3/16 X 3/32 5/16-18 SHC1 1 1-3/4 4 1/4 X 1/8 5/16-18 SHC1-1/8 1-1/8 2 4-1/2 1/4 X 1/8 5/16-18 SHC1-3/16 1-3/16 2 4-1/2 1/4 X 1/8 5/16-18 SHC1-1/4 1-1/4 2-1/8 4-1/2 1/4 X 1/8 5/16-18 SHC1-1/4LK 1-1/4 2-1/8 4-1/2 5/16 X 5/32 5/16-18 SHC1-3/8 1-3/8 2-5/16 4-1/2 5/16 X 5/32 3/8-16 SHC1-7/16 1-7/16 2-5/16 4-1/2 3/8 X 3/16 3/8-16 SHC1-1/2 1-1/2 2-1/2 4-1/2 3/8 X 3/16 3/8-16 SHC1-5/8 1-5/8 2-3/4 4-1/2 3/8 X 3/16 3/8-16 SHC1-3/4 1-3/4 2-3/4 4-1/2 3/8 X 3/16 3/8-16 SHC1-15/16 1-15/16 3-5/16 4-1/2 1/2 X 1/4 1/2-13 SHC2 2 3-5/16 4-1/2 1/2 X 1/4 1/2-13 47
L Jaw Couplings Coupler halves are sold individually Black Oxide finish Keyway and 2 set screws (L050 series have no keyway) Coupler Bore # of Jaws Series Outside Length Thru Bore Keyway L050-3/8 3/8 2 L050 1-7/64 1-1/16 No keyway L050-1/2 1/2 2 L050 1-7/64 1-1/16 No keyway L050-5/8 5/8 2 L050 1-7/64 1-1/16 No keyway L075-7/16 7/16 3 L075 1-3/4 1-9/32 1/8 X 1/16 L075-1/2 1/2 3 L075 1-3/4 1-9/32 1/8 X 1/16 L075-5/8 5/8 3 L075 1-3/4 1-9/32 3/16 X 3/32 L075-3/4 3/4 3 L075 1-3/4 1-9/32 3/16 X 3/32 L075-7/8 7/8 3 L075 1-3/4 1-9/32 3/16 X 3/32 L095-7/16 7/16 3 L095 2-1/8 1-1/2 1/8 X 1/16 L095-1/2 1/2 3 L095 2-1/8 1-1/2 1/8 X 1/16 L095-9/16 9/16 3 L095 2-1/8 1-1/2 1/8 X 1/16 L095-5/8 5/8 3 L095 2-1/8 1-1/2 3/16 X 3/32 L095-3/4 3/4 3 L095 2-1/8 1-1/2 3/16 X 3/32 L095-7/8 7/8 3 L095 2-1/8 1-1/2 3/16 X 3/32 L095-15/16 15/16 3 L095 2-1/8 1-1/2 1/4 X 1/8 L095-1 1 3 L095 2-1/8 1-1/2 1/4 X 1/8 L095-1-1/8 1-1/8 3 L095 2-1/8 1-1/2 1/4 X 1/8 L100-5/8 5/8 3 L100 2-1/2 2-1/32 3/16 X 3/32 L100-3/4 3/4 3 L100 2-1/2 2-1/32 3/16 X 3/32 L100-7/8 7/8 3 L100 2-1/2 2-1/32 3/16 X 3/32 L100-1 1 3 L100 2-1/2 2-1/32 1/4 X 1/8 L100-1-1/8 1-1/8 3 L100 2-1/2 2-1/32 1/4 X 1/8 L100-1-1/4 1-1/4 3 L100 2-1/2 2-1/32 1/4 X 1/8 L100-1-3/8 1-3/8 3 L100 2-1/2 2-1/32 5/16 X 5/32 L100-1-1/2 1-1/2 3 L100 2-1/2 2-1/32 3/8 X 3/16 More sizes continued on the next page... 48
L Jaw Couplings Coupler halves and Buna inserts sold individually Black Oxide finish Keyway and 2 set screws (L050 series have no keyway) Coupler Bore # of Jaws Series Outside Length Thru Bore Keyway L110-5/8 5/8 3 L110 3-11/32 2-1/2 3/16 X 3/32 L110-3/4 3/4 3 L110 3-11/32 2-1/2 3/16 X 3/32 L110-7/8 7/8 3 L110 3-11/32 2-1/2 3/16 X 3/32 L110-1 1 3 L110 3-11/32 2-1/2 1/4 X 1/8 L110-1-1/8 1-1/8 3 L110 3-11/32 2-1/2 1/4 X 1/8 L110-1-1/4 1-1/4 3 L110 3-11/32 2-1/2 1/4 X 1/8 L110-1-3/8 1-3/8 3 L110 3-11/32 2-1/2 5/16 X 5/32 L110-1-1/2 1-1/2 3 L110 3-11/32 2-1/2 3/8 X 3/16 L110-1-5/8 1-5/8 3 L110 3-11/32 2-1/2 3/8 X 3/16 L Jaw Couplings Inserts Buna Inserts Insert L050N L075 L090/095N L099/100N L110N Fits Series L050 L075 L090 & L095 L099 & L100 L110 49
UCP 200 Series Pillow Block Bearings Includes zerk/grease fitting Self aligning bearing Synthetic single lip rubber seal with an outer steel slinger to protect the bearing and inner seal from contaminants. More specs available on the website Bearing Bore Bearing Center Line Overall Length Mounting Hole Spacing Overall Height Base Width (d) (H) (a) (e) (w) (b) UCP202-10 5/8 1-3/16 5 3-3/4 2-15/32 1-1/2 UCP204-12 3/4 1-5/16 5 3-3/4 2-31/64 1-1/2 UCP205-14 7/8 1-7/16 5-1/2 4-1/8 2-25/32 1.343 UCP205-15 15/16 1-7/16 5-1/2 4-1/8 2-25/32 1.343 UCP205-16 1 1-7/16 5-1/2 4-1/8 2-25/32 1.343 UCP206-18 1-1/8 1-11/16 6-1/2 4-3/4 3-5/16 1-7/8 UCP206-19 1-3/16 1-11/16 6-1/2 4-3/4 3-5/16 1-7/8 UCP206-20 1-1/4 1-11/16 6-1/2 4-3/4 3-5/16 1-7/8 UCP207-20 1-1/4 1-7/8 6-9/16 5 3-21/32 1-7/8 UCP207-21 1-5/16 1-7/8 6-9/16 5 3-21/32 1-7/8 UCP207-22 1-3/8 1-7/8 6-9/16 5 3-21/32 1-7/8 UCP207-23 1-7/16 1-7/8 6-9/16 5 3-21/32 1-7/8 UCP208-24 1-1/2 1-15/16 7-1/4 5-13/32 3-27/32 2-1/8 UCP209-26 1-5/8 2-1/8 7-15/32 5-3/4 4-3/16 2-1/8 UCP209-27 1-11/16 2-1/8 7-15/32 5-3/4 4-3/16 2-1/8 UCP209-28 1-3/4 2-1/8 7-15/32 5-3/4 4-3/16 2-1/8 UCP210-30 1-7/8 2-1/4 8-1/8 6-1/4 4-7/16 2-3/8 UCP210-31 1-15/16 2-1/4 8-1/8 6-1/4 4-7/16 2-3/8 UCP211-32 2 2-1/2 8-5/8 6-23/32 4-29/32 2-3/8 UCP211-34 2-1/8 2-1/2 8-5/8 6-23/32 4-29/32 2-3/8 UCP211-35 2-3/16 2-1/2 8-5/8 6-23/32 4-29/32 2-3/8 UCP212-36 2-1/4 2-3/4 9-1/2 7-1/4 5-7/16 2-3/4 UCP212-38 2-3/8 2-3/4 9-1/2 7-1/4 5-7/16 2-3/4 UCP212-39 2-7/16 2-3/4 9-1/2 7-1/4 5-7/16 2-3/4 UCP213-40 2-1/2 3 10-7/16 8 5-29/32 2-53/64 UCP215-47 2-15/16 3-1/4 10-13/16 8-17/32 6-3/8 2-29/32 50
UCFL 200 Series Two Bolt Bearings Includes zerk/grease fitting Self aligning bearing Synthetic single lip rubber seal with an outer steel slinger to protect the bearing and inner seal from contaminants. More specs available on the website Bearing Bore Overall Length Mounting Hole Spacing Overall Height Base Width (d) (a) (e) (Z) (b) UCFL202-10 5/8 3-7/8 3 1.135 2-1/8 UCFL204-12 3/4 4-7/16 3-17/32 1.311 2-3/8 UCFL205-14 7/8 5-1/8 3-57/64 1.405 2-11/16 UCFL205-15 15/16 5-1/8 3-57/64 1.405 2-11/16 UCFL205-16 1 5-1/8 3-57/64 1.405 2-11/16 UCFL206-18 1-1/8 5-13/16 4-19/32 1.530 3-5/32 UCFL206-19 1-3/16 5-13/16 4-19/32 1.530 3-5/32 UCFL206-20 1-1/4 5-13/16 4-19/32 1.530 3-5/32 UCFL207-20 1-1/4 6-11/32 5-1/8 1.750 3-17/32 UCFL207-21 1-5/16 6-11/32 5-1/8 1.750 3-17/32 UCFL207-22 1-3/8 6-11/32 5-1/8 1.750 3-17/32 UCFL207-23 1-7/16 6-11/32 5-1/8 1.750 3-17/32 UCFL208-24 1-1/2 6-7/8 5-21/32 2.015 3-15/16 UCFL209-26 1-5/8 7-13/32 5-27/32 2.062 4-1/4 UCFL209-27 1-11/16 7-13/32 5-27/32 2.062 4-1/4 UCFL209-28 1-3/4 7-13/32 5-27/32 2.062 4-1/4 UCFL210-30 1-7/8 7-3/4 6-3/16 2.156 4-17/32 UCFL210-31 1-15/16 7-3/4 6-3/16 2.156 4-17/32 UCFL211-32 2 8-13/16 7-1/4 2.315 5-1/8 UCFL211-34 2-1/8 8-13/16 7-1/4 2.315 5-1/8 UCFL211-35 2-3/16 8-13/16 7-1/4 2.315 5-1/8 51
SBLF 200 Series Two Bolt Bearings Includes zerk/grease fitting Self aligning bearing Synthetic single lip rubber seal with an outer steel slinger to protect the bearing and inner seal from contaminants. More specs available on the website Bearing Bore Overall Length Mounting Hole Spacing Overall Height Base Width (d) (a) (e) (Z) (b) SBLF204-12 3/4 2-7/8 2-13/16 1.125 2-13/32 SBLF205-14 7/8 3-3/4 2-63/64 1.205 2-17/32 SBLF205-15 15/16 3-3/4 2-63/64 1.205 2-17/32 SBLF205-16 1 3-3/4 2-63/64 1.205 2-17/32 SBLF206-18 1-1/8 4-7/16 3-9/16 1.300 3 SBLF206-19 1-3/16 4-7/16 3-9/16 1.300 3 SBLF206-20 1-1/4 4-7/16 3-9/16 1.300 3 SBLF207-20 1-1/4 4-13/16 3-15/16 1.402 3-1/2 SBLF207-21 1-5/16 4-13/16 3-15/16 1.402 3-1/2 SBLF207-22 1-3/8 4-13/16 3-15/16 1.402 3-1/2 SBLF207-23 1-7/16 4-13/16 3-15/16 1.402 3-1/2 52
UCF 200 Series Four Bolt Bearings Includes zerk/grease fitting Self aligning bearing Synthetic single lip rubber seal with an outer steel slinger to protect the bearing and inner seal from contaminants. More specs available on the website Bearing Bore Overall Length Mounting Hole Spacing Overall Height (d) (a) (e) (Z) UCF202-10 5/8 3 2-1/8 1-5/16 UCF204-12 3/4 3-3/8 2-1/2 1-5/16 UCF205-14 7/8 3-3/4 2-3/4 1-13/32 UCF205-15 15/16 3-3/4 2-3/4 1-13/32 UCF205-16 1 3-3/4 2-3/4 1-13/32 UCF206-18 1-1/8 4-1/4 3-1/4 1-19/32 UCF206-19 1-3/16 4-1/4 3-1/4 1-19/32 UCF206-20 1-1/4 4-1/4 3-1/4 1-19/32 UCF207-20 1-1/4 4-19/32 3-5/8 1-3/4 UCF207-21 1-5/16 4-19/32 3-5/8 1-3/4 UCF207-22 1-3/8 4-19/32 3-5/8 1-3/4 UCF207-23 1-7/16 4-19/32 3-5/8 1-3/4 UCF208-24 1-1/2 5-1/8 4 2-1/64 UCF209-26 1-5/8 5-3/8 4-1/8 2-1/16 UCF209-27 1-11/16 5-3/8 4-1/8 2-1/16 UCF209-28 1-3/4 5-3/8 4-1/8 2-1/16 UCF210-30 1-7/8 5-5/8 4-3/8 2-5/32 UCF210-31 1-15/16 5-5/8 4-3/8 2-5/32 UCF211-32 2 6-3/8 5-1/8 2-5/16 UCF211-34 2-1/8 6-3/8 5-1/8 2-5/16 UCF211-35 2-3/16 6-3/8 5-1/8 2-5/16 UCF212-36 2-1/4 6-7/8 5-5/8 2-23/32 UCF212-38 2-3/8 6-7/8 5-5/8 2-23/32 UCF212-39 2-7/16 6-7/8 5-5/8 2-23/32 UCF213-40 2-1/2 7-3/8 5-7/8 2.563 UCF214-44 2-3/4 7-19/32 6 2-31/32 UCF215-47 2-15/16 7-7/8 6-1/4 3-3/32 53
SBF 200 Series Four Bolt Bearings Includes zerk/grease fitting Self aligning bearing Synthetic single lip rubber seal with an outer steel slinger to protect the bearing and inner seal from contaminants. More specs available on the website Bearing Bore Overall Length Mounting Hole Spacing Overall Height (d) (a) (e) (Z) SBF204-12 3/4 3-3/8 2-1/2 1.516 SBF205-14 7/8 3-3/4 2-3/4 1.5551 SBF205-15 15/16 3-3/4 2-3/4 1.5551 SBF205-16 1 3-3/4 2-3/4 1.5551 SBF206-18 1-1/8 4-1/4 3-1/4 1.7717 SBF206-19 1-3/16 4-1/4 3-1/4 1.7717 SBF206-20 1-1/4 4-1/4 3-1/4 1.7717 SBF207-20 1-1/4 4-19/32 3-5/8 1.9094 SBF207-21 1-5/16 4-19/32 3-5/8 1.9094 SBF207-22 1-3/8 4-19/32 3-5/8 1.9094 SBF207-23 1-7/16 4-19/32 3-5/8 1.9094 SBF208-24 1-1/2 5-1/8 4 2.1220 SBF209-26 1-5/8 5-3/8 4-1/8 2.1614 SBF209-27 1-11/16 5-3/8 4-1/8 2.1614 SBF209-28 1-3/4 5-3/8 4-1/8 2.1614 54
UCT 200 Series Take-Up Bearings Includes zerk/grease fitting Self aligning bearing Synthetic single lip rubber seal with an outer steel slinger to protect the bearing and inner seal from contaminants. More specs available on the website Bearing Bore Overall Length Overall Width Width Slot to Slot Overall Height (d) (W) (a) (e) (Bi) UCT204-12 3/4 3-11/16 3-1/4 3 1.221 UCT205-14 7/8 3-13/16 3-1/2 3 1.343 UCT205-15 15/16 3-13/16 3-1/2 3 1.343 UCT205-16 1 3-13/16 3-1/2 3 1.343 UCT206-18 1-1/8 4-7/16 4-1/32 3-1/2 1.500 UCT206-19 1-3/16 4-7/16 4-1/32 3-1/2 1.500 UCT206-20 1-1/4 4-7/16 4-1/32 3-1/2 1.500 UCT207-20 1-1/4 5-3/32 4-1/32 3-1/2 1.689 UCT207-21 1-5/16 5-3/32 4-1/32 3-1/2 1.689 UCT207-22 1-3/8 5-3/32 4-1/32 3-1/2 1.689 UCT207-23 1-7/16 5-3/32 4-1/32 3-1/2 1.689 UCT208-24 1-1/2 5-21/32 4-1/2 4-1/64 1.937 UCT209-26 1-5/8 5-21/32 4-19/32 4-1/64 1.937 UCT209-27 1-11/16 5-21/32 4-19/32 4-1/64 1.937 UCT209-28 1-3/4 5-21/32 4-19/32 4-1/64 1.937 UCT210-30 1-7/8 5-7/8 4-19/32 4-1/32 2.032 UCT210-31 1-15/16 5-7/8 4-19/32 4-1/32 2.032 UCT211-32 2 6-23/32 5-3/4 5-1/8 2.187 55