ref.: T4750 rev. no.: 2 date: 10/04 page: 1/1 Flexibility Tractel s Swingstage Division has a full range of Safety Tieback Anchors to suit every building and budget; from the standard U-bar model, to more aesthetic Domed or Flush Mounted anchors, as well as Wall Mounted Models used when roof penetration is not an option. Swingstage s anchors will suit any building condition: they can be bolted, welded, clamped, cast-in or fixed with adhesive anchors. Our design team can quickly address any special conditions or requirements. SAFETY TIEBACK ANCHORS When securing building maintenance systems, including outriggers and bosun s chairs to buildings, Swingstage s Safety Tieback Anchors provide the code-regulated level of safety required ensuring problem free equipment use. Swingstage Safety Tieback Anchors can also be used as Lifeline Anchors for personal fall protection. With a separate independent lifeline, rope grab, lanyard and body harness, the safety anchor becomes a principal component in a safety lifeline system. Conformity Anchors are designed to meet all applicable safety codes, regulations and standards where applicable, including OSHA, CalOSHA, ASME/ANSI and CAN/CSA-Z91-M90, which govern loading and location of these required safety devices, as well as the types and sizes of material used in their construction. Swingstage s anchors also meet regulations that state safety-anchoring devices must be designed by a registered professional engineer. Our engineering team can assist you in conforming to code requirements, without installing more anchors than necessary. Performance Safety tieback anchors can be used as primary suspension or safety suspension points for workers with safety harnesses and bosun s chairs with controlled descent apparatus. They are also used as tie-offs for primary or secondary, portable and permanent suspension equipment, including outriggers with suspended platforms. safety tieback lifeline anchor primary suspension tieback safety lifelines Typical tieback rigging for outriggers and platform
tieback anchors roof mounted ref.: T4785 date: 06/04 page: 1/3 SAFETY TIEBACK ANCHORS When securing building maintenance systems, including outriggers and bosun s chairs to buildings, Swingstage s Safety Tieback Anchors provide the code-regulated level of safety required ensuring problem free equipment use. Swingstage Safety Tieback Anchors can also be used as Lifeline Anchors for personal fall protection. With a separate independent lifeline, rope grab, lanyard and body harness, the safety anchor becomes a principal component in a safety lifeline system. Standard Connections Conformity Anchors are designed to meet all applicable safety codes, regulations and standards where applicable, including OSHA, CalOSHA, ASME/ANSI and CAN/CSA-Z91-M90, which govern loading and location of these required safety devices, as well as the types and sizes of material used in their construction. Weld to Steel 5000 Lbs. (5400 Lbs. California) Ultimate load in any direction U-Bar - 3/4 Dia. stainless steel Embedded Anchor Galvanized Steel Pipe support 4 Dia. Flashing and sealing by others Typical standard heights of 12, 1 or 24 Thru Bolt Structure must resist applied load with a minimum safety factor of 4:1 by others Hilti Anchor 2004 Tractel. All rights reserved.
SAFETY TIEBACK ANCHORS - Flush type tieback anchors flush type ref.: T4785 date: 06/04 page: 2/3 Standard Connections When securing building maintenance systems, including outriggers and bosun s chairs to buildings, Swingstage s Safety Tieback Anchors provide the code-regulated level of safety required ensuring problem free equipment use. Flush mounted When tiebacks are required on roofs where aesthetics, pedestrians or other traffic does not permit any protuberances, Tractel s flush mounted tiebacks provide an attractive solution. All varieties of standard models are available for every mounting method including new or retrofit applications Weld to Steel Conformity Anchors are designed to meet all applicable safety codes, regulations and standards where applicable, including OSHA, CalOSHA, ASME/ANSI and CAN/CSA-Z91-M90, which govern loading and location of these required safety devices, as well as the types and sizes of material used in their construction. Top of finished roof 5000 Lbs. (5400 Lbs. California) Ultimate load in any direction Embedded Anchor Hot dip galvanized flush tieback anchor Flashing and sealing by others Height to top of finished roof TBD Thru Bolt Structure must resist applied load with a minimum safety factor of 4:1 by others 2004 Tractel. All rights reserved. Hilti Anchor
SAFETY TIEBACK ANCHORS tieback anchors wall mounted ref.: T4785 date: 06/04 page: 3/3 Standard Connections When securing building maintenance systems, including outriggers and bosun s chairs to buildings, Swingstage s Safety Tieback Anchors provide the code-regulated level of safety required ensuring problem free equipment use. Wall Mounted Safety Tieback Anchors When tiebacks are required on roofs where waterproofing or flashing is not an option, Tractel s wall mounted tiebacks provide a simple, inexpensive solution. Conformity Anchors are designed to meet all applicable safety codes, regulations and standards where applicable, including OSHA, CalOSHA, ASME/ANSI and CAN/CSA-Z91-M90, which govern loading and location of these required safety devices, as well as the types and sizes of material used in their construction. Embedded Anchor Flashing and sealing by others Hot dip galvanized wall mount Thru Bolt U-Bar - 3/4 Dia. stainless steel 5000 Lbs. (5400 Lbs. California) Ultimate load in any direction Structure must resist applied load with a minimum safety factor of 4:1 by others Hilti Anchor 2004 Tractel. All rights reserved.
ref.: T4768 date: 02/01 page: 1/4 U-bar Safety Tieback Anchors The standard U-bar are the economical solution for securing secondary safety lifelines or for equipment tieback. All varieties of standard models are available for every mounting method. Flashing & Sealing SAF0007A-SAF0016A Available All our anchors are designed to meet or exceed all applicable safety codes, regulations and standards where applicable, including FEDOSHA, CALOSHA, ASME/ANSI and CAN/CSA-Z91-M90. U-BAR - 3/4 DIA. STAINLESS STEEL TYPE-304 TRS1800S & TRS2400S TRT1200S & TRT1800S GALVANIZED STEEL PIPE SUPPORT 4 DIA. OPTIONAL RIGID INSULATION ALL FLASHING AND SEALING REQUIRED FIELD WELD 5/16 TOP OF BUILDING STRUCTURAL STEEL U-BAR - 3/4 DIA. STAINLESS STEEL TYPE-304 GALVANIZED STEEL PIPE SUPPORT 4 DIA. OPTIONAL RIGID INSULATION ALL FLASHING AND SEALING REQUIRED 2 THREADED RODS CENTERED (3/4 UNC SS304 THREADED ROD C/W 3/4 UNC DOUBLE NUTS) 1 TRS1800S or 24 TRS2400S 12 TRT1200S or 1 TRT1800S 4 MIN 7 MAX Tractel model TRS1800S & TRS2400S U-Bar Safety Tieback Anchor, welded to wide beam. (w/o bottom plate) U Bar: 3/4 dia. type 304 stainless steel Pipe Support: 4 dia. galvanized steel Notes: FIELD WELD E70XX ELECTRODE FINISH HOT DIP GALVANIZED Tractel model TRT1200S & TRT1800S U-Bar Safety Tieback Anchor, bolted to structure. U Bar: 3/4 dia. type 304 stainless steel Pipe Support: 4 dia galvanized steel Base & Clamp Plate: galvanized steel (11 square base plate & 11 x 4 clamp plate) STRUCTURE TO WITHSTAND APPLIED LOADING BY OTHERS 11 5 1/4 MAX 2 1/4 MIN 2 Threaded Rods & Nuts: 3/4 UNC SS304 thread rod c/w 3/4 UNC double nuts Note: finish hot dip galvanized
ref.: T4768 date: 02/01 page: 2/4 U-bar Safety Tieback Anchors The standard U-bar are the economical solution for securing secondary safety lifelines or for equipment tieback. All varieties of standard models are available for every mounting method. Flashing & Sealing SAF0007A-SAF0016A Available All our anchors are designed to meet or exceed all applicable safety codes, regulations and standards where applicable, including FEDOSHA, CALOSHA, ASME/ANSI and CAN/CSA-Z91-M90. STEEL TYPE-304 GALVANIZED STEEL PIPE SUPPORT 4 DIA. OPTIONAL RIGID INSULATION FLASHING AND SEALING REQUIRED SINGLE U-ANCHOR BOLT CENTERED (3/4 UNC SS304 THREADED ROD C/W DOUBLE NUTS STRUCTURE TO WITHSTAND APPLIED LOADING BY OTHERS STEEL TYPE-304 GALVANIZED STEEL PIPE SUPPORT 4 DIA. OPTIONAL RIGID INSULATION FLASHING AND SEALING REQUIRED 4 ADHESIVE ANCHORS (HVA M20X240) CENTERED (M20 SS304 THREADED ROD C/W M20 DOUBLE NUTS) STRUCTURE TO WITHSTAND APPLIED LOADING BY OTHERS 11 SQ 11 SQ 12 TRE1200S or 1 TRE1800S 5 6 MIN 12 TRM1200S or 1 TRM1800S 6 11/16 MIN TRE1200S & TRM1200S & TRE1800S TRM1800S Tractel model TRE1200S & TRE1800S U-Bar Safety Tieback Anchor, embedded anchor bolt into concrete. U Bar: 3/4 dia. type 304 stainless steel Pipe Support: 4 dia. galvanized steel Base Plate: 11 square galvanized steel U-Anchor Rod & Nuts: 3/4 UNC SS304 thread rod c/w 3/4 UNC double nuts Note: Finish hot dip galvanized Tractel model TRM1200S & TRM1800S U-Bar Safety Tieback Anchor, adhesive anchor into concrete. U Bar: 3/4 dia. type 304 stainless steel Pipe Support: 4 dia. galvanized steel Base Plate: 11 square galvanized steel Adhesive Anchor & Nuts: M20x240 SS304 threaded rod c/w M20 double nuts (Available) Note: Pull test all adhesive anchors to 4000lbs by others Finish hot dip galvanized
wall mounted models ref.: T4768 date: 02/01 page: 3/4 Wall Mounted Safety Tieback Anchors When tiebacks are required on roofs where waterproofing or flashing is not an option, Tractel s wall mounted tiebacks provide a simple, inexpensive solution. All varieties of standard models are available for every mounting method, including new or retrofit applications. Like all Tractel tiebacks, they are load rated at 5400 lbs. in any direction, and meet or exceed all required safety codes. ALL FLASHING AND SEALING BY OTHERS 3 6 MIN 5 TWE1000S Tractel model TWE1000S TWT1000S GALVANIZED STEEL PLATE STEEL TYPE 304 Wall mounted safety tieback anchor, embedded in concrete. SINGLE U-ANCHOR BOLT CENTRED (3/4 UNC SS304 THREADED ROD C/W 3/4 UNC DOUBLE NUTS 1 1/2 U - Bar: 3/4 dia. type 304 stainless steel Top Plate: Galvanized steel - 11 x 5 U - Anchor & Nuts: 3/4 UNC SS304 threaded rod c/w 3/4 UNC double nuts Note: Finish hot dip galvanized ALL FLASHING AND SEALING BY OTHERS GALVANIZED STEEL PLATE 2 3/4 4 MIN 7 MAX 2 1/4 MIN 5 1/4 MAX Tractel model TWT1000S Masonry wall mounted safety tieback anchor, bolted to structure. STEEL TYPE 304 U - Bar: 3/4 dia. type 304 stainless steel Top Plate: Galvanized steel - 11 x 5 TWO THREADED RODS CENTRED (3/4 UNC SS304 THREADED ROD C/W DOUBLE NUTS 1 1/2 Two Threaded Rods & Nuts: 3/4 UNC SS304 threaded rod c/w 3/4 UNC double nuts Note: Finish hot dip galvanized
wall mounted models ref.: T4768 date: 02/01 page: 4/4 Wall Mounted Safety Tieback Anchors When tiebacks are required on roofs where waterproofing or flashing is not an option, Tractel s wall mounted tiebacks provide a simple, inexpensive solution. All varieties of standard models are available for every mounting method, including new or retrofit applications. Like all Tractel tiebacks, they are load rated at 5400 lbs. in any direction, and meet or exceed all required safety codes. ALL FLASHING AND SEALING BY OTHERS GALVANIZED STEEL PLATE STEEL TYPE 304 1 1/2 TWM1000S Tractel model TWM1000S TWC1000S Wall mounted safety tieback anchor, adhesive anchor into concrete. U - Bar: 3/4 dia. type 304 stainless steel FOUR ADHESIVE ANCHORS (HVA M20x240) CENTRED (3/4 UNC SS304 THREADED RODS C/W DOUBLE NUTS Top Plate: Galvanized steel - 11 x 5 Adhesive Anchors & Nuts: Four adhesive anchors (hva m20x240) centred, two 3/4 unc ss304 threaded rods c/w double nuts (Available) 2 3/4 6 11/16 MIN Notes: Pull test all adhesive anchors to 4000 lbs. by others Finish hot dip galvanized GALVANIZED STEEL PLATE STEEL TYPE 304 1 1/2 Tractel model TWC1000S Wall mounted safety tieback only, mounting method by others. ALL FLASHING AND SEALING BY OTHERS U - Bar: 3/4 dia. type 304 stainless steel Top Plate: Galvanized steel - 11 x 5 2 3/4 Notes: Mounting method by others, Tractel not responsible for incorrect installation. Finish hot dip galvanized